Directed Xpresskit DBALL2 Installation Manual

Important! This product is compatible with vehicles equipped with a manual transmission. NOT Remote Start Ready ( RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. Installation Guide Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Vehicle Application Guide ....... .................. .... ................................. ............................... ...................................................... Installation s s (Wiring Diagram & Vehicle Wiring Reference Chart ) Type 1 ............................................................................................ ....................................................... ............................ Type 2 ............................................................................................ ....................................................... ............................ SmartStart/ 202 Installation Notes.................................................................................................................................. XL Programming Module Programming ...................... ....... ....................................................................... .......... ........................................... Module Reset.. ................................................................................................................................................................ ... Hard ... .... Reset.. ................................................................................................................................................................ Feature & Option List.......................................................................................................................................................... Feature Programming......................................................................................................................................................... LED Diagnostics & Troubleshooting................................................................................................................................... Limited One-Year Consumer ........ Warranty....................................................................................................................... Quick Reference Guide...................................................................................................................................................... 02 03 05 07 08 09 09 10 10 11 13 14 Index SmartStart Compatible SmartStart is equipped with D2D which means it can be connected to an interface module and used in , Remote Start Ready ( ) mode the use of See the section for more RSR without a remote starter. Module Programming information. The NISS06 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Nissan vehicles. This guide supports the installation of a DBALL2 in Remote Start Ready ( ) mode. This solution offers three (3) configuration options to control your system: 3x Lock RSR OEM Remote Start Activation, System or SmartStart (all sold separately). RF This module can only be flashed and configured using Xpress VIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to for more information. the Module Programming section 8 on page Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

Page 2 The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles 2017 2016 2015 2014 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Trunk / Hatch Release RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-Ignition Status Nissan Rogue (Smart Key) 2 1 1 1 • • • • • • • • • • • • • • • • • • • Legend: AV: Horn & Lights Controls DL: OE Door Lock & Alarm Controls PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

Liftgate switch) Important! The devices, but supplied with the . Hood Pin and Remote Start Safety Override Switch are mandatory safety are NOT DBALL Hood Pin Remote Start Safety Override Switch [ ] 2 HS CAN High: 3 Tan/Black: [ ] 2 HS CAN Low: 4 Tan: (-) Ground: 7 Brown: (-) Ignition Output: 8 Yellow: (-) Ground: 11 Yellow/Red: (-) Output: 12 Starter Brown/Red: 6: White/Black: (-) Hood Input (-) Unlock Output: 1 Black/White: (-) Push-To-Start: 2 Green/Black: (-) Lock Output: 3 Green/White: (-) : 4 Hazards Output Red/Black: [1] ( ) - Trunk Release Output: 12 Blue/Red: (-) Ground: 14 Black: (+) 12V: 13 Red: BCM E29 M19 M18 B16 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 8 9 7 6 5 4 3 2 1 (-) Lock: Brown, pin 12 (-) Unlock: pin 13 Pink, (-) PTS: Yellow, pin 9 40 39 38 37 36 35 34 33 32 31 30 29 28 11 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 10 9 8 7 6 5 4 3 2 1 BCM Connector M19 (Black conn. at BCM) BCM Connector M18 (Grey conn. at BCM) ( ) - Starter: Green, pin 19 18 15 24 20 16 13 22 19 21 17 14 23 6 3 12 8 4 1 10 7 9 5 2 11 BCM Connector E29 (Black conn, at BCM) [ ] 2 HS CAN High: in 6 Blue, p [ ] 2 HS CAN Low: in 14 Pink, p Diagnostic connector OBDII 1 8 16 9 1 White conn. (back of dash fuse box) ( ) : pin 1 + 12V Green or Blue, Diode A s 3 x 1 [1] (-) P : in ower Liftgate , p 7 Lt. Green (-) Accessory 1: Lavender/White, pin 28 (-) Ignition 1: , Yellow pin 27 (-) Hazards: , Yellow pin 11 (-) : pin Accessory 2 25 Brown, You can connect to either a XL202 RFTD a SmartStart module. OR Refer to the SmartStart/ XL202 Installation Notes for more information. Installation Type 1 Page 3 10 2 DBALL RF Prog Button . LED 4 14 12 2 With the exception of the OBDII Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise). s [ ] 2 If the module does not program, the HS CAN connections can be made at the BCM. See the installation guide for the 2017 Nissan Rogue (Smart Key). [ ] 1 T . he vehicle MUST be disarmed for the power tailgate to operate Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

Installation © 2017 Directed. All rights reserved. Page 4 Type 1 - Vehicle Wiring Reference Chart Function Color Pin Polarity Location Color Pins Nissan Rogue (Smart Key) 2014-2016 12V Blue or Green 1 (+) Back of dash fuse box. White 1 Power Liftgate Lt. Green 7 (-) Power liftgate switch. Green 8 Starter Green 19 (-) Connector E29, BCM under drivers dash. Black 24 HS CAN High Blue 6 Data OBDII. White 16 HS CAN Low Pink 14 Data OBDII. White 16 Ignition 1 Yellow 27 (-) Connector M18, BCM under drivers dash. Gray 40 Accessory 1 Lavender/White 28 (-) Connector M18, BCM under drivers dash. Gray 40 Accessory 2 Brown 25 (-) Connector M18, BCM under drivers dash. Gray 40 Hazards Yellow 11 (-) Connector M18, BCM under drivers dash. Gray 40 PTS Yellow 9 (-) Connector M19, BCM under drivers dash. Black 40 Lock Brown 12 (-) Connector M19, BCM under drivers dash. Black 40 Unlock Pink 13 (-) Connector M19, BCM under drivers dash. Black 40 Connector Information

. Hood Pin and Remote Start Safety Override Switch are mandatory safety are NOT DBALL HS CAN High: 3 Tan/Black: HS CAN Low: Tan: 4 (-) Ground: 7 Brown: (-) Ignition Output: 8 Yellow: (-) Ground: 11 Yellow/Red: (-) Output: 12 Starter Brown/Red: (-) Unlock Output: 1 Black/White: (-) Push-To-Start: 2 Green/Black: (-) Lock Output: 3 Green/White: (-) : 4 Hazards Output Red/Black: [1] ( ) - Trunk Release Output: 12 Blue/Red: (-) Ground: 14 Black: (+) 12V: 13 Red: BCM E29 M19 M18 B16 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 8 9 7 6 5 4 3 2 1 (-) Lock: Brown, pin 12 (-) Unlock: pin 13 Pink, (-) PTS: Yellow, pin 9 BCM Connector M19 (Black conn. at BCM) ( ) - Starter: Green, pin 19 18 15 24 20 16 13 22 19 21 17 14 23 6 3 12 8 4 1 10 7 9 5 2 11 BCM Connector E29 (Black conn, at BCM) 1 White conn. (back of dash fuse box) ( ) : pin 1 + 12V Green or Blue, 1 2 3 4 5 6 7 8 9 19 18 17 16 15 14 13 12 11 10 20 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 40 BCM Connector B16 (Green conn. at BCM) HS CAN High: Blue, 20 pin HS CAN High: Pink, 40 pin Power Liftgate (Green conn. at Liftgate switch) [1] (-) P : in ower Liftgate , p 7 Lt. Green 40 39 38 37 36 35 34 33 32 31 30 29 28 11 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 10 9 8 7 6 5 4 3 2 1 BCM Connector M18 (Grey conn. at BCM) Diode A s 3 x 1 (-) Accessory 1: Lavender/White, pin 28 (-) Ignition 1: , Yellow pin 27 (-) Hazards: , Yellow pin 11 (-) : pin Accessory 2 25 Brown, Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input installation Type 2 Page 5 10 2 DBALL RF Prog Button . LED 4 14 12 2 You can connect to either a XL202 RFTD a SmartStart module. OR Refer to the SmartStart/ XL202 Installation Notes for more information. Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input installation Type 2 Page 5 10 2 DBALL RF Prog Button . LED 4 14 12 2 You can connect to either a XL202 RFTD a SmartStart module. OR Refer to the SmartStart/ XL202 Installation Notes for more information. All adapters are displayed from the wire side (unless specified otherwise). [ ] 1 T . he vehicle MUST be disarmed for the power tailgate to operate Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

Installation © 2017 Directed. All rights reserved. Page 6 Type 2 - Vehicle Wiring Reference Chart Function Color Pin Polarity Location Color Pins Nissan Rogue (Smart Key) 2017 12V Blue or Green 1 (+) Back of dash fuse box. White 1 Power Liftgate Lt. Green 7 (-) Power liftgate switch. Green 8 Starter Green 19 (-) Connector E29, BCM under drivers dash. Black 24 HS CAN High Blue 20 Data Connector B16, BCM under drivers dash. Green 40 HS CAN Low Pink 40 Data Connector B16, BCM under drivers dash. Green 40 Ignition 1 Yellow 27 (-) Connector M18, BCM under drivers dash. Gray 40 Accessory 1 Lavender/White 28 (-) Connector M18, BCM under drivers dash. Gray 40 Accessory 2 Brown 25 (-) Connector M18, BCM under drivers dash. Gray 40 Hazards Yellow 11 (-) Connector M18, BCM under drivers dash. Gray 40 PTS Yellow 9 (-) Connector M19, BCM under drivers dash. Black 40 Lock Brown 12 (-) Connector M19, BCM under drivers dash. Black 40 Unlock Pink 13 (-) Connector M19, BCM under drivers dash. Black 40 Connector Information

be purchased separately. optional XL MUST Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information. PKE 4 4 XL202 Antenna XOVER SmartStart is and not included. It be purchased separately. optional MUST SmartStart is and not included. It be purchased separately. optional MUST Th solution offers ( ) configuration options to control your system Kit e Remote Start Ready ( ) two 2 : DBALL RSR RF both This section provides specific installation information for SmartStart and 202. or SmartStart ( sold separately). XL Configuration Wires (Gray & White) Connect Gray wire to (-) Ground 5 pins D2D (4 pins, white) 4 pins 2 pins, not used CABLE CABLE The modules must be connected in a specific order. Refer to the section for more information. Module Programming 1. Use the D2D Crossover ( ) cable that is provided with 202, and the one in the package. XOVER XL NOT DBALL 2. The modules must be connected in a specific order. Refer to the section for more information. Module Programming The modules must be connected in a specific order. Refer to the section for more information. Module Programming SmartStart/ 202 Installation Notes XL SmartStart Revision B RF Kit RF & PKE Combination Kit Refer to the Passive Keyless Entry ( PKE) Installation Guide (N2102T) for detailed wiring information. RF PKE BT , & SmartStart Combination Kit SmartStart Revision A 2 DBALL 2 DBALL 2 DBALL LED Prog. Button D2D (4 pins, white) 4 pins 2 pins, not used OR SmartStart Configuration Wires (White & Brown or Blue) Cut Brown or Blue Loop LED THIS SIDE UP LED Page 7 Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

ensure everything is correct prior to moving onto the next step. Note: Before connecting either the 202 or SmartStart module to , it is important to ensure that the proper feature and XL DBALL function programming is selected using Xpress (version 4. or higher). Visit www.directechs.com to download the latest VIP 5 version of the application. Warning! To take advantage of advanced features, you must use Xpress VIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features. 1. Connect the interface module to your computer using the XKLoader. 2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page. 3. Select the , and of the vehicle; the page will refresh to display the compatible firmware. year make model 4 In the search result page, select , and follow the instructions provided on the screen. . Config for RSR 5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module. 6. The following message will be displayed when the upload is completed: “The flashing is successfully completed. You may now unplug the kit.” You can now proceed with the programming instructions below. Page 8 1 10-pin D2D 1 st 12-pin 14-pin 2 nd 3 rd & Solid Connect the 10-pin 2-pin harnesses to , 1 and 14-pin DBALL, then w . ait until the turns solid red LED ON 10-pin D2D XL202 10-pin D2D SmartStart OR The module be disconnected from any power source before SmartStart can DBALL must be connected to it. Failing to do so could damage DBALL. a. To ensure that the D2D communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source ( Rev B SmartStart), and the Brown or Blue loop must be cut ( Rev A SmartStart). b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by the D2D connector. DBALL Connect SmartStart to using the D2D port. DBALL SmartStart Installation Connect 202 to using the D2D port. XL DBALL XL202 Installation Refer to the Diagnostics section on page 1 for more information and for troubleshooting purposes. LED s 11- 2 You have successfully completed the module programming sequence. 2 3 Press P to turn ignition O the ush-to-Start button FF once the module is once successfully programmed. 1X ENGINE START STOP PUSH Press P to turn ignition ON. the ush-to-Start button once The LED turns ON solid green for 3 seconds, then shuts OFF. Note: If the bypass was skipped, the LED flashes orange then turns ON solid orange for 3 seconds and shuts off. Important: Do press the brake pedal. NOT 1X ENGINE START STOP PUSH & & Solid x 3 sec. Off Do NOT press the brake pedal Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

harnesses to the module Press hold the rogramming . and p button, then connect the 14-pin harness to the module. 10-pin D2D 1 st 12-pin 14-pin 2 nd 4 th 3 rd Warning gainst xecuting a Hard Reset! A E A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as and D2D options) may have to be reconfigured. See the section of this guide. RFTD Feature & Option List 2 Solid & Release 3 Release the programming button. The turns solid red. LED ON Module Reset Hard Reset 2 & & 1 Wait 3 seconds until the orange then release the LED turns ON solid p The turns solid red. rogramming button. LED ON If required for your installation, connect the 10-pin & 12-pin harnesses to the module Press hold the rogramming . and p button, then connect the 14-pin harness to the module. 10-pin D2D 1 st 12-pin 14-pin 2 nd 4 th 3 rd A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. Page 9 Solid Release Solid Solid Flashes & Wait 3 seconds until the orange ait LED turns solid , and w 10 more seconds ON until the LED starts to flash orange and red. Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

It is recommended to configure all features and options listed below the the using configuration tool found on the module flashing page on www.directechs.com. The web offers more options such as RSR; however, manual configuration of the features is possible using the information on this page. * Default Option Feat. Operation Flashes/Options Description 1. No RF Output* Module is connected to a remote starter using a standard installation. 2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available). 3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available). 1. Disabled The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter. 2. Safelock Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown. 3. Enabled* Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user. RFTD Output Type 1 2 Smart OEM Alarm Control To enter feature programming routine � Turn t , then he ignition . ON OFF � Within 5 seconds, press and the rogramming button turns after 3 seconds . Release the HOLD LED ON p until the orange ( ) Programming button. � The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicate LED LED will flash green once slowly red the current option of feature 1 . (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence will repeat until . a new command is entered Changing feature options � Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the DBALL RSR OEM in using 3x Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground will change the option for the selected feature. � The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowly LED LED red the number of times to indicate the current feature. repeat until . The flashing sequence will a new command is entered Accessing another feature � Press and release the programming button a number of times to advance from the current feature to the next desired feature. � The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly to LED LED indicate the current option of the current feature. repeat until . The flashing sequence will a new command is entered When the maximum number of features or options is reached, the will start flashing again from the first feature or option. LED Once a feature is programmed � Other features can be programmed. � The feature programming can be exited. Exiting feature programming � No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programming LED ON sequence. OR � Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm the HOLD LED ON end of the programming sequence. Feature Programming Programming Button Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

Page 11 LED Description Troubleshooting Module has no power. Make sure the D2D harness is connected or that the 12 Volt is present between the red and black wires. If the 12 Volt is present, the module may be defective. Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. Initialization failed. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. Transponder functions were skipped. (If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module. All required CAN networks has been detected. Normal operation. 1 of 2 CAN networks has been detected. Normal operation Key2GO initiated. Please follow the steps indicated in “Module programming” to complete the Key2GO programming. Module was successfully programmed with all functions. Normal operation Module was successfully programmed without transponder functions. Normal operation. CAN2 not detected. Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. J1850 not detected. Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again. CAN1 not detected. Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Bypass data not detected. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. Bypass processing error. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. ISO 1 not detected. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. ISO 2 not detected. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. MUX not detected. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. Module Programming Module Programming - Error Codes Solid red Flashes red x 1 Flashes red x 1 Flashes red x 2 Flashes red x 3 Flashes red x 4 Flashes red x 5 Flashes red x 6 Flashes red x 7 Solid green x 3 secs Flashes green Solid orange Flashes red & green Off Flashes orange Flashes orange slowly Solid orange x 3 secs Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

Installation © 2017 Directed. All rights reserved. LED Description Troubleshooting OBDII feature is not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. Ground When Running (Status) command received. The module has initialized the remote start sequence. Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Start ON command received. The module has received the Start ON command and is processing the remote start sequence. PTS shutdown error. The PTS output from the module was not activated due to safety protection. CAN bus incorrectly detected. Verify the CAN1 and CAN2 connections. Refer to “Installation (wiring diagrams & vehicle wiring reference charts)” to check the connections. LOCK command received. UNLOCK command received. TRUNK command received. AUX1 command received. AUX2 command received. AUX3 command received. Takeover successful. Normal operation. Runsafe was not disabled. No UNLOCK command was received prior to opening the door, or the 45 second timer expired in takeover mode. Brake was not detected. The brakes were not detected, which prevents the system from shutting down the vehicle. Smart key was not detected. The smart key was not detected, which prevents the system from shutting down the vehicle. Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. 3x OEM Lock Remote Start Activation was attempted when RFTD feature is disabled. Activated from Web automatically when using RSR flash tool or can be done manually. Refer to feature programing section for more information. Feature error. An RSR feature file mismatch was detected. Please contact Technical Support. RSR codes External module synchronization Commands Activation Ground When Running (Status) If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D. Shutdown codes (Flashes red, red then orange) x 10 Flashes red & orange Flashes red x 21 Flashes red x 2 Flashes red x 4 Flashes red x 7 Flashes red x 9 Flashes red x 10 Flashes red x 1 Flashes red x 3 Flashes green Flashes green quickly Flashes green x 1 Flashes orange x 1 Flashes orange x 2 Flashes orange x 3 Flashes orange x 5 Flashes orange x 4 Flashes orange x 6 Page 12

Page 13 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“ DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING , , , BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY , , , FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY , ; PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS , PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANYAND ALLACTS OF . THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR . A INSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS , , , , AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER , INCLUDING WITHOUT LIMITATION , LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING , , . A A DIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF , CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE . DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED . TO THE AUTHORIZED DIRECTED DEALER ’S PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE . RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL , , DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL , , , , LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE , . , MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THE A ’S PARTAS DESCRIBEDABOVE. This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States of America or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitations AS IS NO WARRANTY on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com 920-10012-01 2013-07 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada. Rev.: 20 170712 Platform: DBALL2 Firmware: NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved.

and put the gear in Park (P). Press remote start button* * Your aftermarket remote may differ from the model shown in the illustrations. Stop & put vehicle in Park (P) P & Flashes ENGINE START STOP & Quick Reference Guide DBALL2-NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved. Pit Stop Mode The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running. Note: We recommend that you always lock the doors of your vehicle when leaving it unattended. It is now safe to leave the engine running and exit the vehicle with the factory remote in hand. Press the button to remote start the vehicle.* The PTS button will flash once to indicate the vehicle is now in Pit Stop Mode. Parking Light Error Codes The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Flashes Diagnostic 1 Runtime expired. 2 Over-rev shutdown. 3 Low/No RPM. 4 Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/Remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, safety override switch input will report 7 flashes. Get In and Go Get In and Go is designed to provide users with easy takeover when entering their Push-to-Start (PTS) equipped vehicle, once it has been remote started. Typically, users would have to remote start their vehicle, then get inside and press the vehicle start button to perform a takeover. There is therefore a physical action required to drive away. With Get In and Go technology, you simply remote start the vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and enjoy your vehicle. This unique feature monitors a variety of parameters such as the key fob, vehicle speed sensor and door sensor, in order to perform takeover securily. GG Vehicle Takeover with Get In and Go* 4 3 1 Press the remote start button on the transmitter to start the vehicle.** 2 Close the door then press the brake pedal, put the car in gear and drive off. Enter the vehicle, while making sure the factory remote is inside with you. Press the Unlock button on the factory or aftermarket remote.** Ready to drive off Press remote start button** Press Unlock button on either remote** OR ** Your aftermarket remote may differ from the model shown in the illustrations. Enter vehicle with key fob GG * Get In and Go connections required. Exit vehicle with Smart Key

DBALL2-NISS06 Remote Start Ready (RSR) Installation © 2017 Directed. All rights reserved. Button(s) Actions Press & hold for 1 second to lock. Press & hold for 1 second to unlock. Press & hold for 1 second to remote start. Press & hold for 5 seconds to activate the trunk release (optional). Press once, then to activate the rear hatch/tail glass release (optional).* Press 3 times, then to activate the panic mode. Press once, then to reset the remote starter runtime. List of Available Commands x1 + x3 + x1 + * This output is configurable. see your authorized installation center for more information. Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Remote Start Ready (RSR) Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. SmartStart Compatible This system is compatible with Directed SmartStart 3.0. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: Ÿ Lock/Arm Ÿ Unlock/Disarm Ÿ Remote Car Starter Ÿ Trunk Release Ÿ Panic Ÿ Aux Channels You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It's easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more. 3.0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com.