Directed Electronics 4103 Quick Reference Install Manual

1 Quick Reference Install Guide Remote Start with Keyless Entry 4103-series Multi-button remote Control Button (Valet Switch) Door Lock/unlock Harness Side View Antenna Antenna LED (Programming indicator) Parking light jumpers Primary Harness Remote Start Harness Heavy Gauge Relay Side View Satellite Harness Red 4-pin port, Bitwriter/ ESP2 or D2D 4x03 Wiring Connections Main Harness (H1), 9-pin connector H1/1 LIGHT GREEN BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT H1/2 GREEN/WHITE (-) 200mA FACTORY ALARM REARM OUTPUT H1/3 YELLOW (+) IGNITION OUT (TO ALARM) H1/4 WHITE/BLUE (-) ACTIVATION INPUT H1/5 ORANGE (-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT H1/6 BROWN (-) 200mA HORN OUTPUT H1/7 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT H1/8 BLACK GROUND INPUT H1/9 WHITE (+/-) LIGHT FLASH OUTPUT Heavy Gauge Relay, 6-pin connector 1 PINK OUTPUT TO PRIMARY IGNITION CIRCUIT 2 PURPLE OUTPUT TO STARTER CIRCUIT 3 ORANGE OUTPUT TO ACCESSORY CIRCUIT 4 RED (+) (30A) HIGH CURRENT 12V INPUT 5 PINK/WHITE OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT 6 RED (+) (30A) HIGH CURRENT 12V INPUT Satellite harness - 4-pin connector 1 BLUE (-) 200mA STATUS OUTPUT 2 ORANGE (-) 200mA ACCESSORY OUTPUT 3 PURPLE (-) 200mA STARTER OUTPUT 4 PINK (-) 200mA IGNITION OUTPUT Remote Start harness (H3), 5-pin connector H3/1 BLACK/WHITE (-) NEUTRAL SAFETY SWITCH INPUT H3/2 VIOLET/WHITE TACHOMETER INPUT H3/3 BROWN (+) BRAKE SHUTDOWN INPUT H3/4 GRAY (-) HOOD PIN SWITCH SHUTDOWN INPUT H3/5 BLUE/WHITE (-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT Installation Points Tach Learning To learn the tach signal: 1. Start the vehicle with the key. 2. Within 5 seconds, press and hold the Valet (Control) button. 3. After 3 seconds the system LED will light constant when the tach signal is learned. 4. Release the Valet (Control) button. Important: This unit can learn the tachometer with the analog input or through D2D using an interface module. The unit confirms which source is used. When programming tach learning with: •� Analog, the parking lights flash one time •� D2D inerface module, the parking lights flash twice If the tachometer input on the system is connected to the vehicle, the D2D tachometer input will be ignored. Virtual Tach Note: Virtual tach is not recommended for diesel vehicles. To program Virtual Tach: 1. After the install is complete, remote start the car. 2. If the car does not start on the first attempt, let the remote start attempt again. 3. Once the car starts, let it run until the parking lights come on. 4. When the parking lights come on, shut off the remote start with the remote - that’s it! Virtual Tach is programmed. Virtual Tach handles disengaging the starter motor during remote starting – it does not address over-rev. If the customer wants to have the over-rev protection capabil- ity, the tach wire must be connected. This may involve more installation shop charges than initially quoted. Important: If the Virtual Tach mode over cranks or doesn't crank the vehicle long enough to start and run the car, use the Bitwriter to add or subtract the starter output time. You can adjust the output time in incre- ments of 50msec of the learned time using the Bitwriter. Red 4-pin port, Bitwriter/ESP2 or D2D programming The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port. The factory default is Bitwriter/ESP2 mode. To use as D2D mode follow the below steps: 1. Make sure White/Blue activation wire is grounded. 2. Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode change. 3. Remove the White/Blue wire from ground. To change from D2D to Bitwriter/ESP2 mode: 1. Make sure the White/Blue activation wire is grounded. 2. Power the unit up, the system LED turns on solid for 5 seconds to confirm Bit- writer/ESP2 mode change. 3. Remove the White/Blue wire from ground. The procedure can be repeated to toggle from one mode to the other. Important: If you power up the system with the White/Blue activation wire ungrounded, the system LED will come on solid for 5 seconds indi- cating the system is in Bitwriter/ESP2 mode. Reset and Deletion If a feature/virtual tach needs to be reset or the remote controls need to be deleted, use the following procedure. 1. Turn the ignition to the ON position (The heavy gauge pink wire must be con- nected). 2. Within 10 seconds, press and release the Valet button: 2 times if you want to delete remotes, 3 times to reset features or 4 times to reset virtual tach. These features are described next. Delete remotes: This feature erases all remotes from the memory of the system. This is useful in cases when a customer’s remote is lost or stolen. Note: This does not reset the programmed features of the system or reset the Virtual Tach setting. Reset Features: This resets all features of the system to the factory default settings. Note: This feature does not delete the remotes from the system or reset the Virtual Tach setting Virtual Tach Reset: Deletes all previously learned values for Virtual Tach, and on the next remote start sequence the unit begins virtual tach initial- ization. Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach setting. 3. Once you have selected the function step, press the Valet button once more and hold it. The LED flashes and the horn honks to confirm the selected func- tional step. Do not release the Valet button 4. While holding the Valet button, press the AUX button on the remote control. The horn honks to confirm that the feature has been successfully reset. Once the feature is reset, the Valet button can be released. Remote Start Shutdown Diagnostics To perform shutdown diagnostics: 1. With the ignition Off, press and hold the Valet button. 2. Turn the ignition On and then back Off while holding the Valet button. 3. Release the Valet button. 4. Press and release the Valet button. The LED flashes to report the last shutdown for one minute or until the ignition is turned on, as shown in the following table: LED Flashes Shutdown Mode 1 flash Timed out 2 flashes Over-rev shutdown 3 flashes Low or no RPM, low battery (voltage and virtual tach modes) 4 flashes Transmitter shutdown (or optional push button) 5 flashes (-) Hood Shutdown (H3/4 GRAY) 6 flashes (+) Shutdown (H3/3 BROWN) 7 flashes (-) Neutral safety shutdown (H3/1 BLACK/WHITE) 8 flashes Wait-to-start timed out Door Lock, 3-pin connector 1 LIGHT BLUE (-) UNLOCK OUTPUT 2 EMPTY NOT USED 3 GREEN (-) LOCK OUTPUT Guide Translations For a Spanish version of the Installation Guide, please download it from www. directechs.com under Resources. Estimado Cliente: Si buscas los guías de instalación, por favor de bajar lo del Resources en el sitio www.directechs.com

2 QRN4103 2011-12 Programming System Features The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the feature settings using the Valet button. 1. Turn the ignition on, then off. 2. Select a Menu. Within 10 seconds, Press and hold the Valet button. The number of LED flashes and horn honks indicates the menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2 honks indicates menu 2. 3. When the desired menu LED flashes and honks are heard, release the Valet button. 4. Select a Feature. Within 10 seconds, Press and release the Valet button the number of times correspond- ing to the feature you wish to change. Then press and hold one more time to select the feature. The LED flashes and the horn honks to indicate which feature is selected. 5. Program the Feature. While holding the Valet button, you can program the feature using the remote control. For features with only two options; AUX = option 1 while AUX = option 2. For features with more than two options; AUX selects the options in ascending order. The LED flashes and the horn honks indicating which option is selected. Once a feature is programmed: •� Other features can be programmed within the same menu •� Another menu can be selected •� The learn routine can be exited if programming is complete To access another feature in the same menu: 1. Press and release the Valet button the number of times necessary to advance from the feature you just pro- grammed to the next one you want to program. 2. Then press the Valet button once more and hold it. To select another menu: 1. Press and hold the Valet button. 2. After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu has been accessed. The learn routine exits if any of the following occurs: •� The ignition is turned On •� There is no activity for 30 seconds •� The Valet button is pressed too many times Bitwriter - Only Options If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet button. The Bitwriter® gives you access to a wider range of system options. These additional features and the adjust- ments that may be programmed are described in the table below. Menu Item Feature Default Options 1 Engine Runtime 12 min. 1-60 min. 2 Diesel start type Off Timed 3 Diesel start delay time (seconds) 15 sec 1-90 sec. 4 Virtual Tach Fine Tune Not initialized 0 to 1 second in 50 millisecond increments 5 Remote control programming Unlocked Locked 6 Feature Programming Unlocked Locked Feature Menus Default settings are in bold type. Menu 1 Feature # Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+ 1 Horn function Off Siren 20 mS Siren 30 mS Siren 40 mS Siren 50 mS 2 Ignition con- trolled lock On Off 3 Ignition con- trolled unlock On Off 4 Doorlock out- put duration 0.8 sec. 3.5 sec. 0.4 sec. 5 Double pulse unlock Off On 6 Double pulse lock Off On 7 Factory Alarm Disarm func- tion with unlock Before unlock Remote start only 8 Factory Alarm Disarm Pulses Single Double 9 Comfort Closure Comfort Closure 1 Off Comfort Closure 2 10 Panic On Off Menu 2 Feature # Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+ 1 Engine check- ing Virtual tach voltage Off tachometer 2 Engine Runtime 12 min 24 min 60 min 3 Park light output Pulsed Constant 4 Cranking time 0.6 sec. 0.8 sec. 1.0 sec. 1.2 sec. 1.4, 1.6, 1.8, 2.0, 4.0 sec 5 Activation pulse count 1 pulse 2 pulses 3 pulses 6 2nd Ignition behavior Ignition Accessory 7 Accessory output Off during wait-to-start On during wait-to-start 8 2nd Status behavior Normal Latch rear defogger Pulse rear defogger 9 Anti-grind On Off 10 Diesel start delay Off Timed 15 sec Timed 30 sec. Timed 45 sec. 11 Timer mode run time 12 min 3 min 6 min 9 min See full Installation Guide for more detailed information on this system. Such information and more can be found online at: www.directechs.com Logo, Directed Electronics w-driven.eps Logo, Directed with designed in USA.eps Directed Logo Usage Remote Programming 1. Turn key to the ON position 2. Within 10 seconds, press and release Valet button one time. 3. Within 10 seconds, press and hold the Valet button. The LED will flash one time and the horn honks (if connected) to confirm entry into remote programming. 4. Press the AUX button on the remote control. 5. The horn honks to confirm the remote has been programmed. 6. Release the Valet button, and turn the key to the Off position. 7. The horn sounds one long honk to confirm that remote programming has been exited. The programming routine exits if any of the following occurs: •� The ignition is turned off •� There is no activity for 30 seconds •� The Valet button is pressed too many times Basic Remote Functions Button Function A U X LOCK A U X UNLOCK AUX TRUNK RELEASE AUX AUX REMOTE START Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M). Some bitwriters with a date code of 6B do not require the IC upgrade, refer to tech tip # 1112 for more information. The Bitwriter® (p/n 998U) re- quires chip version 2.7 or newer to program this unit.