Aladdin 37 Manual 

ALADDIN BLUE FLAME HEATER This heater is manufactured in accordance with British Oil Heater Regulations 1966, British Standard 3300:1974 and other national and international safety standards and regulations where relevant. Additionally and in accordance with the amendments to the British Standard effective from May 1st 1969, the heater is fitted with an extinguisher which puts out the flame if the heater is accidentally knocked over. However heat is produced, carelessness and ignorance can cause accidents, so for your own comfort and safety, please read and understand these instructions before lighting your heater. The numbers in brackets in the text will help you to identify the parts on the illustrations. The illustrations are on the last page and are identified by symbols in the margins of the text. UN PACKING We have been generous with the packing to make sure that your heater gets to you without damage; make sure you remove all the packing before lighting. EXTINGUISHER DEVICE Before filling the tank the extinguishing device should be checked as follows: Stand the heater on the floor as shown on the front cover of this leaflet. Set the mechanism by pressing down the resetting lever sticking out of the chimney. The lever will move easily until near the end of its travel and then some resistance will be felt as the sensing weight on the mechanism is pulled up to its set (vertical) position. To check the mechanism, remove the top cover and rock the heater over on two feet. Look inside the top of the chimney and you will see the sensing weight falling over releasing the extinguisher which will slide down over the top of the burner. Reset the extinguisher and repeat the operation to ensure that the mechanism is working freely. Note: Leave the carrying handle down when the heater is in use or it will overheat. FILLING The tank (P.169917) will hold one Imperial gallon (1.2 U.S. gallons or4•5 litres). Use only premium grade paraffin (domestic kerosene) conforming to British Standard 2869C1. It is very dangerous to use any other fuel such as petrol or power kerosene. Remember, put absolutely nothing but best quality paraffin in your tank or storage container and make sure it cannot become contaminated in any way. The filler cap/air valve (P.169902) unscrews. This part is extremely important in the functioning of the heater so please handle it carefully. If the small air hole in the top of the cap becomes blocked with dirt or fluff it must be cleared by blowing through from the top of the cap. Don’t use wire or pins etc., as you may damage the diaphragm underneath Wipe dry any paraffin which may occasionally seep through the air hole. As a precaution against over-filling, the oil gauge (P.199916) is designed to register full when the tank is approximately 80% full. To obtain the maximum burning time quoted for your heater, it will be necessary to disregard the oil

maximum capacity. This must be done carefully to avoid over-filling--the level of paraffin must not rise above the bottom of the filler neck. The oil gauge also indicates when the heater needs refilling. Do not allow the heater to burn dry thus causing the wick to smoulder which will shorten the life of the wick and lessen performance. LIGHTING When you use the heater for the first time, or have fitted a new wick, do not light it for at least an hour so that the wick has a chance to soak up enough paraffin. Release the clip and swing open the chimney. Check that the flame spreader (P.329900), which has a large number of small holes in it, is fitted in the centre tube of the tank. If it has fallen out or is not seated properly it must be replaced and pushed fully home before the heater is lit. Make sure the burner basket (P.151000) is locked fully into the tank. The wick winder “W” turns clockwise to raise the wick (P.169901). With just enough wick showing (you should still see five rows of holes on the flame spreader), light the wick all the way around and then press the extinguisher resetting lever down and hold it down whilst closing the heater, checking carefully that the spring clip is properly fastened. Release the resetting lever, leaving it in the down position. If the lever is not left in the down position the heater will be extinguished as soon as the lever is released. The burner reaches working temperature very quickly, so you should Immediately adjust the wick to give you the required heat within the limits of the SAFE BLUE FLAME. THE SAFE BLUE FLAME Remember that your safety indicator is the colour of the flame. When the flame is a clear blue all over you have got the SAFE BLUE FLAME. When the flame shows any yellow the wick is too high or too low or something is wrong with the heater never letthe heater burn like this—it could cause smoking. This visual safety indicator is so important and so simple to use that a little practice at first will amply repay you. Short periods of yellow flame are not dangerous so you can safely try the settings for yourself. Turn the wick winder anti-clockwise CN until the heater is almost out and you will get aflickering yellow edge to the flame; this is too low. Raise the wick until a completely blue flame is obtained and then raise a little more so that it cannot revert to yellow; this is the lowest setting for the SAFE BLUE FLAME. As you turn the wick up more the blue flame will grow and you may notice a reddish glow above the flame and possibly intermittent red flecks of burning dust. This is quite normal. Eventually yellow spikes will appear at the top edge of the flame to warn you that you have gone too far. Lower the wick until you get rid of the yellow spikes and you now have the highest setting for the SAFE BLUE FLAME. LEAVING THE HEATER As long as you have the SAFE BLUE FLAME you can confidently leave your heater unattended, but do take a few simple precautions against accidents. Place the heater on a level surface out of draughts and where it can’t be knocked over. Make sure that children cannot play with it. You and the heater

get enough. EXTINGUISHING After you have turned the wick right down to extinguish the heater, turn it up again and look to make sure it is really out. It is vita! to ensure that the flame is out—a low yellow flame will overheat the burner and could cause smoking. USING WICK CLEANER A good flame depends on a clean wick. The wick should not be cleaned until it has been used for 50 hours or more. There after, about once a week remove the flame spreader (P.329900), turn the wick right down, make sure the wick cleaner (P.1 59904) is the right way up (trade mark “Aladdin” uppermost) and place it on the top of the burner Whilst turning the wick cleaner clockwise fl with one hand, slowly turn the wick up with the other. Maintain a gentle downward pressure on the wick cleaner to keep it level and touching the rim of the burner basket (P.151000). When the rising wick reaches the cleaner, j black carbon will come through the three holes. This will soon stop and your wick will be clean and properly shaped for further use. Wipe the rim of the burner basket clean before replacing the flame spreader. The wick must be kept shaped at the correct angle and this can only be done with the wick cleaner provided. Never use scissors, razor blades, etc. Please store the wick cleaner in a safe place. Do not keep it near the heater chimney as the temperature could be sufficient to soften and distort it. CLEANING THE HEATER A dirty heater may smell and can even be dangerous, particularly if fluff or carbon is blocking any of the air holes. Wipe off any paraffin which has been spilt during filling and clean regularly to get rid of all dust, fluff and carbon. Take out the flame 9 spreader (P.329900) and burner basket (P.151000) for cleaning and don’t forget to clean the gallery which can be seen at the bottom of the chimney when the heater is open. Hot soapy water can be used as long as none gets in the tank or on the wick, but you must never use abrasives. RESHAPING WICK If the top edge of the wick becomes unevenly burnt away and one side of the flame is much higher than the other, or burning yellow, you must not use the heater until the wick has been reshaped. Put the heater where the smell won’t matter, and let it burn completely out. Careful use of the wick cleaner now, and for the next day or two of normal burning, will fully restore the shape of the wick. . FITTING NEW WICK Carefully used, the wick will last a remarkably long time, but when it will no longer turn up enough get a new one—forcing the wick winder will only result in an unnecessary repair bill. Take out the flame spreader (P.329900) and remove the burner basket (P.151000) by turning anti-clockwise � Th. Turn the wick up until the cog is free and then pull the wick and carrier out of the tank. Disengage the teeth on either side of the wick by pressing the top of the wick above the teeth and draw the old wick out of the carrier.

Holding the carrier (P.379935) in one hand with the flanged end at the top, and the new wick in the other, insert the tails through the top of the wick carrier until the two teeth on each side of the wick are immediately above the slots on either side of the carrier. Gently squeeze the wick above the teeth and ease it down until they engage with the lowest set of slots in the carrier as shown at “A”. Grasp the ends of the tails together with the bottom of the carrier and gently draw the assembly over the centre tube of the tank “B”. Line up rack on wick carrier with the winder cog “C” and gently push the assembly down until the rack engages with the winder cog. Then turn the wick down with the winder—ensuring at the same time that the tape on the inside of the wick does not catch on top of the centre tube. Replace burner basket and lock firmly in position by turning clockwise. Replace the flame spreader. Refill the tank and allow the wick to soak for at least an hour before lighting. As the wick is consumed during normal use it will be found that it cannot be turned up high enough to give a full height flame. When this happens, withdraw the wick and carrier as described above and re-position the wick in the next higher set of slots in the carrier. This may be done several times until a full height flame becomes impossible even with the wick in the highest slots, at which stage a new Aladdin wick must be fitted. The capital letters, A, B and C in the text will guide you to the various Wick Fitting illustrations on the last page. MAINTENANCE Replace any damaged or worn out part immediately with a genuine Aladdin spare—we cannot accept any responsibility if substitutes are used. Once a year rinse out the tank with clean paraffin (kerosene) and fit a new wick. If you cannot get the SAFE BLUE FLAME or are in any difficulty take the heater to your nearest Aladdin stockist. Never use a heater which is not working properly. SAFETY PRECAUTIONS 1. Always ensure that the heater is placed on a level surface and the handle is in the down position when the heater is alight. 2. Use only premium grade paraffin conforming to BS 2869 grade C1. We recommend ‘Pink” paraffin available in U.K. and Eire only; NEVER USE petrol or any other fuel. 3. Make sure the flame is Blue. 4. Keep all parts of the heater clean, particularly the burner and chimney. 5. Ensure the room is well ventilated—fresh air must have access, but do not put the heater in a draught. 6. Do not fill when alight. Do not carry while alight. Do not allow clothes or any article on or near the heater. Do not place the heater where it can be knocked over. 7. Replace damaged parts immediately. 8. Use only Aladdin spares—others can be dangerous. 9. Make sure the heater is guarded if children are in the room alone. 10. Do not add salt or anything else to the fuel—it’s useless and harmful. 11. Provision for fixing. There are screw holes in the feet of the heater.

substantial air inlet at floor level, together with a fanlight or window slightly open, provided such opening is not obstructed by completely drawn curtains. IT IS PARTICULARLY IMPORTANT to observe this precaution and ensure adequate ventilation if it is intended to sleep in a room in which there is an oil heater in use. NEVER USE YOUR O1L HEATER IN A ROOM WH1CH HAS BEEN COMPLETELY SEALED AGAINST DRAUGHTS. AL WA YS ENSURE THA T THE DRA UGHT EXCL UDER (P.160803) IS FITTED FIRML Y INTO THE UNDERSIDE OF THE TANK. SPECIFICATIONS Heat output.. .. .. .. .. .. .. .. .. .. .. B.Th.U’s per hour—5,870—9,320 Kilogram Calories per hour - 1,470 - 2,330 Equivalent to .. .. .. .. .. .. .. .. .. .. . .. 13/4 – 23/4 kilowatts (approx.) Consumption.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 25-16 hrs. per gallon Approximate capacity.. .. .. .. .. .. .. .. .. .. .. .. .. .. 1 gallon (45 litres) ______________________________________________________________ SPARE PARTS P.329900 Flame spreader P.169901 Wick P.379935 Wick carrier P.151000 Burner basket P.1 59904 Wick cleaner P 379963 Hinge pin with washers and nuts P.379908 Handle P.169902 Filler cap with air valve, washer and chain P.339905 Oil gauge only (Optical) P.169903 Oil gauge cap and washer P.150225 Dome nut P.370300 Bottom frame P.169917 Tank complete P.151910 Top cover P.379906 Top frame, chimney, gallery, boiling ring assembly P.370500 chimney and gallery assembly P.379903 Mica and screws P.151604 Frame and screws for mica If you have any difficulty in obtaining spare parts for your Blue Flame Heater please write to us: ALADDIN INDUSTRIES LTD., GREENFORD, MIDDLESEX.

GREENFORD, ENGLAND or in certain countries by one of the following licensors: ALADDIN INDUSTRIES INC., NASHVILLE, U.S.A. INDUSTRIES ALADDIN, S.A., PARIS ALADDIN INDUSTRIES PTY., LTD., SYDNEY Information on request from Patent Department, Aladdin Industries Ltd., Greenford, England. These devices are the registered Trade Marks of Aladdin Industries Limited in Great Britain GB. Patent Nos. 1001029, 1048229, 1079716 and Foreign Patents