Xerox 721 Message Manual
Read Online
Read the Xerox 721 Message Manual online using the built-in PDF viewer.
Text of the manual
701 S. Aviation Boulevard
El Segundo, CA 90245
© 1994, 1995 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of
copyrightable material and information now allowed by statutory
or judicial law or hereinafter granted, including without limitation,
material generated from the software programs which are
displayed on the screen, such as icons, screen displays, looks,
etc.
Printed in the United States of America
Xerox® and all Xerox products mentioned in this publication are
trademarks of Xerox Corporation. Products and trademarks of
other companies are also acknowledged.
WARNING: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
Changes are periodically made to this document. Changes,
technical inaccuracies, and typographic errors will be corrected in
subsequent editions.
This document was created on the Xerox 6085 Professional
Computer System using VP software. The typeface is Optima.
The Xerox 4635 Laser Printing System Message Guide Guide is
part of the ten-manual reference set for your laser printing
system. The entire reference set is listed in the table below.
Several other related documents are also listed for your
convenience. For a complete list and description of available
Xerox documentation, refer to the Xerox Documentation Catalog
(Publication number 610P17417) or call the Xerox
Documentation and Software Services (XDSS) at 1-800-445-5554.
Publication
Number
Xerox Dynamic Document Interface
Operator Guide
720P13670
Xerox Dynamic Document Interface
Command Summary
720P13680
Xerox 4635 Laser Printing System
Operator Guide
721P83010
Xerox 4635 Laser Printing System
Operations Reference
721P83020
Xerox 4635 Laser Printing System
Sysgen Guide
721P83030
Xerox 4635 Laser Printing System
Message Guide
721P83040
Xerox 4635 Laser Printing System
PDL/DJDE Reference
721P83050
Xerox 4635 Laser Printing System
Forms Creation Guide
721P83060
Xerox 4635 Laser Printing System
Product Reference
721P83070
Xerox 4635 Laser Printing System
Installation Planning Guide
721P83080
Xerox 4635 Laser Printing System
Operator Command Summary Card
721P83090
Xerox 4635 Laser Printing System
PC UI Reference
721P83100
Xerox Laser Printing Systems
Tape Formats Manual
600P86175
Xerox Laser Printing Systems
Standard Font Library Font User Guide
600P86174
Xerox 4850 HighLight Color and 4135
Laser Printing Systems Font User Guide
720P87340
Helpful Facts About Paper
721P82490
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
iii
This publication may contain descriptions of concepts and
features not currently available for your Xerox Laser Printing
System. Consult your Xerox sales representative or your
operating system software program description for additional
information.
iv
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
Table of contents
Related publications
iii
Notice
iv
Introduction
vii
About the reference set
vii
4635 Laser Printing System document set
vii
What the message guide contains
x
How the message guide is organized
xi
The conventions used in this guide
xii
1. CP (COMPRESS command) messages
1-1
2. DSR (disk save and restore command) messages
2-1
3. FD (forms compilation) messages
3-1
4. HIP (host interface processor) messages
4-1
5. IFU (Interpress font utility) messages
5-1
6. OSS (operating system software) messages
6-1
OS Level 0: Confirmation
6-1
OS Level 1: Information
6-9
OS Level 2: Routine maintenance
6-41
OS Level 3: Printer problem
6-65
OS Level 4: System or tape problem
6-71
OS Level 6: Job integrity
6-75
OS Level 7: System problem
6-95
OS Level 8: Probable severe software error
6-100
OS Level 9: Probable severe hardware error
6-107
7. PDL (job source library compilation) messages
7-1
8. PG (PURGE command) messages
8-1
9. PR (HARDCOPY graphics printing command) messages
9-1
10. PSC (printer subsystem controller command) messages
10-1
11. SCALE command messages
11-1
12. SFS (status file services command) messages
12-1
13. System verification error messages
13-1
14. Summary sheet error messages
14-1
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
v
TABLE OF CONTENTS
Appearance warning messages
14-4
Appearance warning
14-4
Appearance warning (page n)
14-6
Fatal error messages
14-8
Fatal error
14-8
Fatal error (page n)
14-8
Informational messages
14-11
Informational messages
14-11
Master error messages
14-13
Master error (page n)
14-13
Master warning messages
14-18
Master warning (page n)
14-18
System problem messages
14-18
System problem
14-18
System problem (page n)
14-19
15. 4635 LPS additional messages
15-1
Numbered 4635 LPS messages
15-2
Messages 7 through 36
15-2
Messages 41 and 42
15-2
Messages 44 through 48
15-2
Message 538
15-2
Messages 540 and 541
15-2
Messages 544 through 574
15-3
Messages 1538 through 1572
15-7
Messages 3538 through 3579
15-11
Messages 4037 through 4145
15-13
Messages 4500 through 4506
15-14
Messages 9038 through 9068
15-15
Messages 9537 through 9542
15-18
Unnumbered 4635 LPS messages (in alphabetical order)
15-19
Appendix
A.
Xerox support services
A-1
Glossary
GLOSSARY-1
Index
INDEX-1
vi
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
The Xerox4635 Laser Printing Systems Message Guide is one of
the ten manuals which make up your 4635 Laser Printing System
(LPS) Reference Set.
The LPS Message Guide provides an easy to use reference tool
for quickly determining why messages appear on your system
controller display or printed summary sheet, and the appropriate
action(s), if any, to take.
This message guide does not contain detailed explanations of
tasks. Throughout the guide, you are referred to the appropriate
reference manual for detailed information.
About the reference set
This document is part of a reference set designed to help you
receive maximum benefit from your 4635 laser printing system.
To help you select the appropriate document for your needs, the
following section identifies the documents in the set and
describes the information contained in each.
4635 Laser Printing System document set
•
Product overview
•
Hardware and software
•
LPS connections
•
User considerations
•
LPS comparisons
4635 LPS
Product
Reference
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
System overview
•
PC UI procedures
•
Paper facts and procedures
•
Operating procedures
•
Maintenance
•
Problem solving
•
Supplies
•
Meter reading and reporting
4635 LPS
Operator
Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
vii
Print Description Language components and processes
•
Input processing functions
•
Output processing functions
•
PDL/DJDE command summary
•
Page formatting guidelines
•
Character code assignment tables
•
PDL/DJDE programming information with step-by-step
instructions
4635 LPS
PDL/DJDE
Reference
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Configuration options
•
Commands
•
OSS software installation, upgrade, and modification
procedures
4635 LPS
System
Generation
Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Command syntax for operator and system administrator
procedures
•
LPS defaults
•
LPS resources
•
Command summaries
•
Communication and graphics on the LPS
•
Command files
4635 LPS
Operations
Reference
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Basic concepts for creating forms
•
Coding and compiling for LPS Forms Description Language
•
Sample form setup command sets
•
Tips for successful forms creation
4635 LPS
Forms
Creation
Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
PC UI procedures
•
Hierarchy of PC UI windows
4635 LPS
PC UI
Reference
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
OSS and other messages
•
Meaning and recovery procedures
4635 LPS
Message
Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
viii
XEROX 4635 LASER PRINTING SYSTEMS MESSAGE GUIDE
Provides a quick reference of commonly-used operator
commands.
4635 LPS
Operator
Command
Summary
Card
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
LPS basic components and options
•
Tasks that must be accomplished before installation
•
Preinstallation requirements
•
Installation process
•
Postinstallation activities
4635 LPS
Installation
Planning
Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Selection and guidelines
•
Storage and handling
•
Specifications for different printers
Helpful Facts
About Paper
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Characteristics of different formats
•
File organization
•
Data formats
•
Carriage control conventions
Tape Formats
Manual
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Font naming conventions
•
Listing of standard fonts
•
Data sheets
•
Glossary of typography terminology
LPS Standard
Font Library
Font User
Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
•
Available fonts
•
Typography concepts
•
Xerox Font Services
•
Glossary of typography terminology
4850
HighLight
Color and
4135 LPS Font
User Guide
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
XEROX 4635 LASER PRINTING SYSTEMS MESSAGE GUIDE
ix
What the message guide contains
The 4635 LPS Message Guide is divided into the following
chapters:
Chapter 1:
CP (COMPRESS command) messages
Chapter 2:
DSR (disk save and restore command) messages
Chapter 3:
FD (forms compilation) messages
Chapter 4:
HIP (host interface processor) messages
Chapter 5:
IFU (Interpress font utility) messages
Chapter 6:
OSS (operating system) messages
Chapter 7:
PDL (job source library compilation) messages
Chapter 8:
PG (PURGE command) messages
Chapter 9:
PR (HARDCOPY graphics printing command) messages
Chapter 10:
PSC (printer subsystem controller command) messages
Chapter 11:
SCALE command messages
Chapter 12:
SFS (status file services command) messages
Chapter 13:
System verification error messages
Chapter 14:
Summary sheet error messages
Chapter 15:
4635 LPS additional messages
Appendix:
Xerox support services
Glossary
A glossary of terms and abbreviations is provide
Index
An alphabetical listing of all unnumbered messages contained in
this guide
The following information is also provided:
•
Information about ordering additional copies of this message
guide through the Xerox Documentation Subscription Service
(XDSS)
•
An order card for the Customer Documentation Catalog,
which describes other available Xerox documentation
•
A Reader Comment Form. Please take a few minutes to write
your comments about the message guide, and any
suggestions you may have for improving it, on the Reader
Comment Form
•
Chapters 1 through 14 are arranged alphabetically according
to the coded messages as they appear on the system
controller (e.g., CP, DS, and FD) or by the type of uncoded
messages (i.e., scale, summary sheet, and system verification
error).
x
XEROX 4635 LASER PRINTING SYSTEMS MESSAGE GUIDE
How the message guide is organized
•
Tabs separate the chapters for easy reference and are printed
with the code you will see on the system display. For
example, FDL messages appear as FDxxxx on your system
display, thus the tab for the FDL chapter is “FD (forms
compilation).”
•
Coded messages are listed alphanumerically, with the two-
letter code followed by the four-digit numeric code, such as:
OS1000, PD8510, and HP2430. The numeric codes range
from 0 to 9. Generally, the higher the numeric code, the
more serious the problem or condition being reported.
•
Scale and system verification error messages are not
numbered and, therefore, are listed in alphabetical order by
the first word in the message.
•
The message chapters consist of a lefthand “Message”
column and a righthand “Meaning/action” column. The
message column contains each entry‘s message code
followed by the message that appears on the system
controller display, for example:
OS2002 CHECK PAPER SUPPLY IN TRAY 1.
The Meaning/action column contains the meaning of the
message and/or what caused it to be displayed. For example:
Fewer than 25 sheets of paper remain in (feeder) tray 1.
This column also lists the action(s) to take, if any, in response to
the message. For example:
1.
Add paper to (feeder) tray 1.
2.. Press the key to resume printing.
XEROX 4635 LASER PRINTING SYSTEMS MESSAGE GUIDE
xi
The conventions used in this guide
The following conventions are used throughout this guide:
•
When keyed in, most commands can be shortened to three
letters. For example, RESET may be entered as RES.
Commands are shown in capital letters.
•
Variable numbers, letters, and words appear as lowercase
italicized characters. These variables represent the actual
characters you will see in system controller display messages
or will enter in commands. For example, the command FEED
cluster-name and the message OS1010 STARTING JOB xxxx
contain variable elements.
•
There are four symbols used for variables in this guide:
n = Any permitted number. Decimal numbers appear as
nn.nn
x = Any applicable letter. Variable words appear as strings
of x’s, such as xxxx
y = A second variable number or letter appearing when n or
x has already been used in the message
z = A third variable number or letter appearing when n
and/or x and y have already been used in the message
•
The names of keys are indicated in capital letters and
enclosed in delimiters, such as the and
keys.
•
If a printer display message appears in conjunction with a
system display message, it is shown in the Meaning/action
column of the message guide in capital italicized letters, for
example: EMPTY SAMPLE TRAY.
•
The terms “feeder tray,” “paper tray,” and “tray” are used
interchangeably.
•
Other terms used include the following:
enter = Key in a command or response, then press the
or key.
restart job = Send or transmit a job again (online) or
rewind a tape and start job again (offline).
recode job = Rewrite the JSL entry or DJDE, making
necessary changes.
xii
XEROX 4635 LASER PRINTING SYSTEMS MESSAGE GUIDE
CP (COMPRESS command)
messages
These messages may appear during the process of compressing
the system disk. (Refer to your 4635 LPS Operations Reference
chapter on managing LPS resources for additional information.)
CP1010
Compress now restoring the print file
The COMPRESS command was entered. The process has moved
the print file to different area of the system disk.
CP1020
Now processing DP0
CP1030
Now processing DP1
CP1040
Now processing DP2
CP1050
Now processing DP3
The COMPRESS command was entered. The system is currently
compressing the indicated disk pack unit.
Action
None.
CP1800
Compress processor aborting
The ABORT command was entered during the compress process.
The system disk remains partially compressed.
CP1900
Insufficient working memory for compress
Not enough dynamic memory exists for the compress process.
Action
Contact your systems specialist or Xerox representative regarding
obtaining additional memory capacity.
CP2010
Enter ‘A’ to abort or ‘C’ to compress other disks
Multiple disks IDs were specified in the COMPRESS command.
One of the system disks contains so many files that there is not
enough internal memory to load the COMPRESS task.
Action
Enter A to abort compression.
or
Enter C to skip over the full disk and compress others specified
in COMPRESS command.
CP2700
Invalid keyin
The compress command was entered incorrectly.
Action
Reenter command correctly
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
1-1
CP (COMPRESS COMMAND) MESSAGES
CP2710
Keyins are not allowed at this time
Compress process has begun. System cannot process any other
commands entered at this time.
Action
1.
Wait for entire compress process to complete.
2.
Reenter command.
CP2720
Invalid start command
The COMPRESS start command was entered incorrectly.
Action
Reenter COMPRESS.
CP7010
Unable to compress this disk. Use DSR - COMPRESS MODE
The COMPRESS command was entered, but disk contains so
many files that there is not enough internal memory to load
COMPRESS task.
Action
Perform DSR, selecting compressed object mode, to compress
the disk. (Refer to your 4635 LPS Operations Reference chapter
on managing LPS resources for additional information.)
CP9100
File integrity error. Edit and print CPR000.TMP
The system has discovered a multi-allocated sector and is listing
it in a special file (CPR000.TMP). The compress function is
terminated.
Action
1.
Print CPR000.TMP error log to locate the problem.
2.
Call Xerox Customer Service with the information above.
1-2
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
DSR (disk save and restore
command) messages
These messages may appear during the process of saving all disk
files on tape or restoring all files to system disk from tape. (Refer
to your 4635 LPS Operations Reference chapter on managing
LPS resources for additional information.)
DS1010
Save process complete
The DSR command was entered. The system has completed
backing-up system disk data on tape.
DS1020
DSR is saving disk drive 0.
DS1030
DSR is saving disk drive 1.
DS1040
DSR is saving disk drive 2.
DS1050
DSR is saving disk drive 3.
Action
None.
DS2010
Mount and ready DSR tape
The DSR command was entered when no save tape had been
mounted.
Action
Mount the save tape.
DS2020
Mount and ready DSR volume nnnn
The DSR process requires more than one save tape. The system
has encountered the EOV label.
Action
Mount the indicated tape volume.
DS3010
Invalid parameter...DSR aborted
An incorrect density parameter was entered with the DSR
command. The DSR task has terminated.
Action
Reenter the command as DSR or DSR 6250. No other
parameters are accepted.
DS3020
DSR Version 2.0 unable to run on this configuration
DSR version 2.0 is incompatible with the current printer
configuration.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
2-1
DSR (DISK SAVE AND RESTORE COMMAND) MESSAGES
DS8010
Tape error xxxx...DSR aborted
The system has encountered a device error from which it was
unable to recover after several attempts. DSR task is aborted.
Action
1.
Clean the tape drive and retry the task. (Refer to the
maintenance chapter in your 4635 LPS operator guide.)
2.
If the problem continues, replace the save tape.
DS8020
Tape is read only...DSR aborted
The tape is designed to be read but not written. Data cannot be
copied onto it. The DSR task is aborting.
Action
Use a different tape.
DS8030
Tape is write protected
The save tape does not have a write enable ring. Data cannot be
copied onto it. The DSR task will abort.
Action
1.
Add a write enable ring to tape.
2.
Reenter the DSR command.
DS8040
6250 not supported, defaulting to 1600
The DSR 6250 command was entered, but your system does not
support a recording density of 6250 bpi. The system will record
at 1600 bpi.
Action
None.
DS9010
Disk error xxxx...DSR aborted
The system has encountered an error on disk from which it was
unable to recover after several attempts. The DSR task is
aborted.
Action
Contact your systems specialist or Xerox Customer Service.
DS9020
DSR aborted
The DSR task has aborted due to a hardware error.
Action
1.
Retry the DSR task.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
DS9030
File structure integrity error...DSR aborted
This message occurs during the DSR process of saving disk files
to tape. Either multiple-allocated or nonallocated blocks have
been encountered. The DSR process has been cancelled.
Action
1.
Enter the COMPRESS command.
2.
If the compress procedure fails, reformat the disk. (Refer to
your 4635 LPS Operations Reference.)
2-2
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
DSR (DISK SAVE AND RESTORE COMMAND) MESSAGES
DS9040
System error...DSR aborted
An unspecified hardware error has caused DSR task to abort.
Action
1.
Retry the DSR task.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
DS9050
File structure integrity error on xx...DSR aborted
The specified disk drive has a corrupt file structure. A format will
be required.
Action
Reformat the system disk. (Refer to your 4635 LPS Operations
Reference.)
DS9060
Invalid DSR.SAF detected
DSR.SAF is corrupt or incompatible with DSR.
Action
Perform system generation, if authorized to do so, or contact
your systems specialist.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
2-3
3. FD (forms compilation) messages
These messages may appear while forms are being compiled
using Forms Description Language (FDL). (Refer to your 4635
LPS Forms Creation Guide for additional information.)
FD0900
Operator-requested abort
The ABORT command was entered. Compiling is stopped.
Action
None.
FD1000
All forms compiled. Forms compiler exiting
The FDL file-name command was entered. Form(s) have been
successfully compiled and the FDL compiling session is
terminated.
Action
None.
FD1050
Forms compiler resuming
The system is beginning to compile another form after having
completed one previously sent.
Action
None.
FD1800
Forms compiler aborting
The FDL task is being cancelled. The ABORT command was
entered, a system disk error has occurred, or a specified file was
not found. This message appears with all fatal error messages.
Action
None.
FD2700
Unrecognized key-in, key-in ignored. May be reentered
A command was entered incorrectly or placed incorrectly in a
line. The system is ignoring the entry.
Action
Reenter the command correctly. (Refer to your 4635 LPS Forms
Creation Guide.)
FD2710
Invalid character, reenter
The symbol or word entered was incorrect for its location in the
command line.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
3-1
FD (FORMS COMPILATION) MESSAGES
FD2720
Key-in too long. Reenter
The name or word entered exceeds the permitted number of
characters.
Action
Enter a different word within the permitted range. (Refer to your
4635 LPS Forms Creation Guide.)
FD2730
Parameter too long. Reenter
The command parameter entered contained more characters than
permitted.
Action
Reenter the command with an allowable number of characters.
(Refer to your 4635 LPS Forms Creation Guide.)
FD2740
FSL not found or invalid option, check and retry
The Forms Source Library (FSL) file specified does not exist on
system disk. The compiler will abort.
Action
1.
Check FSL for the correct file name.
2.
Create the FSL file on disk if necessary. (Refer to your 4635
LPS Forms Creation Guide.)
3.
Retry the FDL task.
FD2750
Unsupported tape device specified
You have entered the SUBDEV command, and referenced a tape
device that is currently not supported by this system.
Action
Correct the reference parameter in the SUBDEV command. Refer
to your system administrator guide.
FD2915
Security violation
The requested file has been protected by the ABNORMAL
SECURITY = YES PDL statement. An attempt was made to
access it at an incorrect logon level.
Action
To access the file, obtain correct password and logon at Level 5.
(Refer to your 4635 LPS Operations Reference chapter on setting
LPS parameters for additional information.)
FD4500
Error in reading magnetic tape
The system is unable to read the input tape containing FDL. The
compiler will abort. (Refer to the maintenance chapter in your
4635 LPS Operator Guide.)
Action
1.
Clean the magnetic tape drive. (Refer to the maintenance
chapter in your 4635 LPS Operator Guide.)
2. If the problem recurs, recreate the FDL tape.
3-2
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
FD (FORMS COMPILATION) MESSAGES
FD9400-FD9540
Disk/file error messages
The system is unable to access (read, write, open, or close) the
indicated file due to a problem with the disk. Forms Compiler
will abort.
FD9400
Error in closing the source-input file.
FD9410
Error in closing the source-output file.
FD9420
Error in closing the listing/summary file.
FD9430
Error in opening the source/output file.
FD9440
Error in opening the listing/summary file.
FD9450
Error in reading the source-input file.
FD9460
Error in reading the source-output file.
FD9470
Error in writing the source-output file.
FD9475
Error in back-spacing the source-output file.
FD9480
Error in writing the listing/summary file.
FD9485
Error in reading the listing/summary file.
FD9490
Error in back-spacing the listing/summary file.
FD9510
Error in closing context file.
FD9520
Error in opening context file.
FD9530
Error in reading context file.
Action
1.
Retry the entry. The message should not reappear if the
failure was an intermittent memory error.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
3-3
HIP (host interface processor)
messages
These messages may appear on your system controller display if
printer communications have been established through the host
interface processor (HIP). The HIP chapters in your 4635 LPS
Operator Guide and 4635 LPS Operations Reference provide
detailed information on HIP.
HP0010
Host interface processor unloaded
The HIP command was entered. HIP task is activated and ready
to receive jobs.
Action
None.
HP0020
Host interface processor unloaded
The HIP END command was entered. HIP task is deactivated.
Action
Wait for the system to print any files stored in the HIP buffer.
HP0030
Logging enabled
You have entered the HIP LOG [START] command. The system
has enabled the logging of selected XNS operations.
Action
None.
HP0031
Logging disabled
You have entered the HIP LOG [STOP] command. The system is
telling you that it has disabled the logging of selected XNS
operations. You can disable selected XNS operations for the
purpose of record capturing.
Action
None.
HP0080
Concatenated job operator display mode is ‘ON’
In response to an operator command, HIP will display internal
job status while in a concatenated job mode.
Action
None.
HP0085
Concatenated job operator display mode is ‘OFF’
In response to an operator command, HIP will not display
internal job status while in a concatenated job mode.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-1
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP0090
Job concatenation mode is ‘ON’
In response to an operator command, HIP is now in a
concatenated job mode.
Action
None.
HP0095
Job concatenation mode is ‘OFF’
In response to an operator command, HIP is not in a
concatenated job mode.
Action
None.
HP0100
Stopped online
The HIP STOP command was entered while the system was
online. Jobs will be accepted until the HIP buffer is full. No
further jobs will be accepted.
Action
1.
Wait for message HP2100 to appear on the printer display.
2.
Enter the HIP START command to print only jobs in the HIP
buffer.
HP0110
Stopped offline
The HIP STOP command was entered while HIP was offline from
the host. No processes were interrupted.
Action
None.
HP0120
Job aborted: JOB ID xxxx
The HIP ABORT job command was entered. The job indicated
has been cancelled.
Action
None.
HP0130
Log file reset
You have entered HIP LOG [RESET]. The system is informing you
that the log file has been cleared and all information had been
deleted.
Action
None.
HP0210
Transmission aborted: JOB ID xxxx
The HIP ABORT command was entered. The job being sent has
been cancelled.
Action
None.
HP1010
Input starting report - jid xx
This is displayed while in a concatenated job mode if the
concatenated job operator display mode is ON when input starts
a HIP job.
Action
None.
4-2
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP1020
Input report complete - jid xx
This is displayed while in a concatenated job mode if the
concatenated job operator display mode is ON when input
finishes a HIP job.
Action
None.
HP1030
Output starting report - jid xx
This is displayed while in concatenated job mode if the
concatenated job operator display mode is ON when output
starts a HIP job.
Action
None.
HP1040
Output report complete - jid xx
This is displayed while in a concatenated job mode if the
concatenated job operator display mode is ON when output
finishes a HIP job.
Action
None.
HP1100
No jobs to abort
The HIP ABORT command was entered, but the host has not
sent any jobs to the printer.
Action
None.
HP1110
End of job display
All job information appears on the system (controller) display.
No more related information will appear at this time.
Action
None.
HP1120
HIP job queue cleared
No data remains in the HIP buffer; jobs have printed or have
been aborted.
Action
None.
HP1130
Buffer file allocation less than specified
The HIP buffer has less space than specified in the HIP.CMD file
at installation. There may not be enough space to hold the
entire job being sent.
Action
1.
Delete unneeded files from system disk to create more
space.
2.
Compress the disk. (Refer to your 4635 LPS Operations
Reference chapter on managing LPS resources for additional
information.)
3.
Enter SETUP mode to change the HIP buffer file size. (Refer
to your 4635 LPS Operations Reference chapter on HIP-
accessed communicating modes for additional information.)
4.
Resend the job.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-3
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP1140
Cannot abort job(s): xxxx (, yyyy, etc.)
The HIP ABORT jobs command was entered. The system is
unable to process the command because job(s) entered were
not received by printer.
Action
1.
Verify that the job numbers were entered correctly.
2.
Reenter the command.
HP1150
Cannot start job(s): xxxx
The HIP START jobs command was entered, but the system is
unable to process the jobs indicated because they are either not
in the pending or receive state, or they have already been
started.
Action
1.
Verify that the job numbers were entered correctly.
2.
Reenter the command.
HP1160
Logging already enabled
You have entered the HIP LOG [START] command. The system is
informing you that the log is already enabled.
Action
None.
HP1170
Log file allocation less than specified
The system is informing you that there is insufficient disk space in
the file system for the number of log entries specified in the
LOG ENTRIES command. The system allocates the largest
possible number of entries available for the disk space.
Action
None.
HP1171
New log file created
A new log file has been created.
Action
None.
HP1172
Log file empty, nothing to print.
You have entered the HIP SHOW LOG [PRN] command and
there are no entries in the log file.
Action
None.
HP1180
No echo servers on list
There are no echo servers on list.
Action
None.
HP1181
Echo test started. Results available in nnn seconds
The echo test has been started.
Action
None.
4-4
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP1182
Echo test already running
The echo test is running.
Action
None.
HP1183
Invalid echo server specification
You have entered an invalid echo server specification.
Action
None.
HP1184
Echo test was not in progress
The echo test is not in progress.
Action
None.
HP1185
Echo test terminated. echo server: nn
The echo test has been terminated.
Action
None.
HP1190
HIP version n, n
This is an informational message stating the HIP version(s) being
used.
Action
None.
HP1200
Offline pending end of transmission
The HIP OFFLINE command was entered. The printer will go
offline when the current file being received is complete.
Action
None.
HP1207
Offline pending end of current active xns session
The HIP OFFLINE command was entered. The printer will
disconnect from Ethernet when the current session is terminated.
Action
None.
HP1210
Host online. Accepting all jobs
The HIP ONLINE ALL command was entered. The printer and
remote host are communicating, and the host is sending jobs to
the HIP buffer. All print and nonprint files (fonts, forms, or JSLs)
will be accepted.
Action
Enter the HIP START command at the system controller keyboard
to initiate printing.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-5
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP1220
Host online. Accepting print jobs only
The HIP ONLINE command was entered. The printer and the
remote host are communicating, and the host is sending jobs to
the HIP buffer. Only files to be printed will be accepted.
Action
Enter the HIP START command at the system controller keyboard
to initiate printing.
HP1230
Host offline
The HIP OFFLINE or RESET command was entered. The printer
and remote host are no longer communicating.
Action
None.
HP1240
Host not responding
The HIP START command was entered but the host is not online
and communicating with printer. (This message is displayed
every 30 seconds until the host comes online or the interface is
terminated.)
Action
1.
If using Ethernet, verify that the connection is good and that
the printer network address and network number are correct.
2.
If using XPAF, contact your systems specialist or Xerox
Customer Service.
3.
If the failure recurs, call for service.
HP1242
Online interface waiting for communications
HIP is online to the XPAF host and waiting for communications.
Action
None.
HP1246
Receiving communications from host
The host has established the data communications link.
Action
None.
HP1250
Transmission complete: job id xxxx
The host has completed sending the indicated job to the printer.
The job will now begin printing.
Action
None.
HP1260
Interface busy - cannot send file(s)
The HIP SEND command was entered. The interface is busy and
is unable to send files from the host at this time.
Action
Wait for current transmission to complete.
HP1265
Online interface already in use
The XPAF host was already online when the HIP HOST XPF
command was entered.
Action
None.
4-6
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP1270
Change of job nn to file xxxxxx completed successfully
The CHANGE command successfully created the file.
Action
None.
HP1280
HIP reset not allowed. Invalid task state
HIP is online and/or jobs in the HIP queue are not completed.
HIP must be offline and all jobs must be completed before the
HIP RESET command can be invoked (these restrictions do not
apply at logon level 4).
HP1290
Host suspended pending pass-through job initiation
A pass-through job was received and the HIP online interface was
suspended.
Action
None.
HP1291
HIP resuming following pass-through job
The pass-through job has completed and HIP is ready to receive
data
Action
None.
HP1298
XPS communications recovered
HIP can now receive data via the XPS communication mode.
Data received but not yet written to system disk will be copied
from memory (saved at system error restart) and written to
system disk. The system then reestablishes the communications
link and continues to receive the next block of data.
Action
None.
HP1299
XPAF communications recovered
HIP can now receive data via the XPAF communication mode.
Data received but not yet written to system disk will be copied
from memory (saved at system error restart) and written to
system disk. The system then reestablishes the communications
link and continues to receive the next block of data.
Action
None.
HP1300
Assuming negative confirmation
A confirmation prompt requiring a YES or NO response was
displayed. No response was entered within the system’s time
limit. The system is responding as if N were entered.
Action
If the Y response was intended, reenter the command,
responding to the confirmation prompt within the system time
frame of 30 seconds.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-7
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP1320
Function is not supported by current host
The requested function cannot be carried out by the current
host.
Action
None.
HP1325
Command not permitted by current host
You are currently logged on to the system at a level less than 2.
The command you attempted to enter cannot be accepted at
your present level.
Action
1.
Log off and then log on at level 2.
2.
Refer to the appropriate 4635 LPS Operator Guide.
HP1330
Buffersize=xxx, utilization=yy% zzzz blocks used, uuuu
blocks available.
This messsage provides the number of blocks available and the
amount of the buffer already used.
Action
None.
HP1340
Known and current hip hosts:
This message lists the available and currently-used HIP hosts for
your system.
Action
None.
HP1410
End of HIP diagnostic
The HIP command was entered during an interactive diagnostic
test, or the system failed Test 2 or 3. The diagnostic test has
been terminated.
Action
None.
HP1420
End of test 3 analysis
The system failed Diagnostic Test 3. HIP has completed analysis
of Test 3 results and has identified the data line that has failed.
This message follows message HP9431 or HP9432.
Action
None.
HP2010
No host selected
A host has not been selected for HIP.
Action
Enter the appropriate HIPHOST command. (Refer to your 4635
LPS Operations Reference chapter on HIP-accessed
communicating modes for additional information.)
HP2020
Selected host not present on system
The host selected is not available on your system.
Action
Contact your systems specialist or Xerox representative.
4-8
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP2030
“ALL” not allowed at current logon level
HIP ONLINE ALL was entered, but the current LOGON level does
not support HIP ONLINE ALL.
Action
None.
HP2090
Host interface must be online. Enter HIP ‘ONLINE’
or
Host interface must be online. select or enter ‘HIP ONLINE’
Host interface is not online.
Action
Enter or select the HIP ONLINE command.
HP2100
Host file buffer full - enter HIP START
or
Host file buffer full - select or enter HIP START
The HIP STOP command was entered while the system was
online. Input continued transmitting files until the HIP buffer was
full. Host transmission has now stopped.
Action
Enter or select the HIP START command to print files in the HIP
buffer.
HP2110
All jobs will be lost: confirm with ‘Y’.
The HIP ABORT ALL command was entered. This message is a
confirmation prompt.
Action
Enter Y to abort all jobs being processed.
or
If you do not wish to abort all jobs, enter N.
HP2120
Insufficient disk space for host buffering
Fewer than 256 blocks are available for HIP buffer space. There
is not sufficient space to receive and buffer files. The system
cannot go online.
Action
1.
Delete files from system disk to provide more space.
2.
Compress the system disk. (Refer to your 4635 LPS
Operations Reference chapter on managing LPS resources for
additional information.)
3.
Enter the SETUP mode to change the HIP buffer file size.
(Refer to your 4635 LPS Operations Reference chapter on
HIP-accessed communicating modes for additional
information.)
HP2121
Insufficient disk space for log print file
You have entered HIP SHOW LOG [PRN]. There is insufficient
disk space for the printing of the log file.
Action
Clear additional disk space for printing.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-9
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP2130
Overwrite file name.type: CONFIRM
DUPLICATEFILE = VERIFY was entered in the HIP.CMD file at
installation. A file has been sent having the same name as the
file already existing on system disk.
Action
Enter YES if you wish the new file to replace the existing file.
or Enter NO to reject the file transfer.
HP2140
Unable to process jobs list at this time—try again
The HIP START or HIP ABORT command was entered. The
printer is temporarily unable to carry out the requested operation
because of a conflicting ongoing process.
Action
Wait one minute, then reenter the HIP START or HIP ABORT
command.
HP2145
Enter ‘HIP show jobs continue’ for more
The HIP JOBS command was entered to display job queue.
Queue contains more than 20 jobs, so all jobs are not shown on
the display.
Action
Enter the HIP SHOW JOBS CONTINUE command to display the
rest of the job queue entries.
HP2150
HIP job queue full. Enter ‘HIP START.’
or
HIP job queue full. Select or enter ‘HIP START.’
The HIP job queue is full and processing must start in order to
free space for incoming jobs.
Action
None.
HP2160
Enter ‘HIP show log continue’ for more
There are more than 20 entries in the log and you must enter
HIP SHOW LOG CONTINUE to view additional screens.
Action
None.
HP2165
Insufficient disk space for log files.
You have entered HIP LOG [START]. There is insufficient disk
space to begin logging.
Action
Delete home files to create space for logging procedures.
HP2200
Rejected nonprint file transfer
An unacceptable nonprint file was sent; therefore, the system did
not store it. (Acceptable file types are those specified in the
ACCEPT command in HIP.LIB.)
Action
Edit HIP.LIB and add the file extension to the
ACCEPT=command.
4-10
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP2210
File send not allowed
The file SEND command is not permitted.
Action
None.
HP2220
File specified to send does not exist
The file requested to be sent does not exist.
Action
Verify that the file name is correct and retry the command.
HP2230
File send request rejected by host
The request to send a file cannot be processed.
Action
Make sure the host is in a state to receive files, and retry the
command.
HP2240
Send request rejected by queue saturation
HIP SEND was rejected due to a “queue full” condition.
Action
Wait until jobs have printed, then reenter the HIP SEND request.
HP2290
Pass-through pending, enter ‘HIP START.’
or
Pass-through pending, select or enter ’HIP START.’
A pass-through job has been sent from the XPAF host; HIP must
be started.
Action
None.
HP2300
Command error at: part of command in error
The command part indicated was entered incorrectly.
Action
Reenter the command correctly. (Refer to the HIP chapter in
your 4635 LPS Operator Guide.)
HP2310
Reenter command
An incorrect command was entered.
Action
Reenter the correct command. (Refer to the HIP chapter in your
4635 LPS Operator Guide.)
HP2320
Invalid command with current host type
The command entered is not correct for the current host.
Action
Enter the command appropriate for your current host. (Refer to
your 4635 LPS Operations Reference chapter on HIP-accessed
communicating modes for additional information.)
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-11
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP2330
Invalid command with no host specified
A host must be selected before the command can be carried
out.
Action
1.
Select a host. (Refer to your 4635 LPS Operations Reference
chapter on HIP-accessed communicating modes for
additional information.)
2.
Reenter the command.
HP2340
Cannot change: HIP must be in ‘STOP’ state.
To invoke the CHANGE command, HIP must be in the STOP
state and the file must be completely received and in the
PENDING state.
Action
None.
HP2341
Cannot change: job must be in ‘PENDING’ state.
To invoke the CHANGE command, HIP must be in the STOP
state and the file must be completely received and in the
PENDING state.
Action
None.
HP2342
Cannot change: change process already active.
Only one CHANGE command can be invoked at one time.
Action
Allow the current change process to complete before invoking
another.
HP2343
Cannot change: invalid file specification.
The output file-type is either invalid or not a type specified in the
ACCEPT list.
Action
None.
HP2344
Cannot change: job does not exist.
The jid specified does not exist in the HIP job queue.
Action
None.
HP2345
Cannot change: output file already exists
The file specified is already resident on the disk.
Action
Rename the output file and retry the CHANGE command.
4-12
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP2346
Command not allowed on system UI.
This message is in response to a service-oriented command
which creates a display that the system PC-UI is not capable of
handling.
Action
Use a LINK terminal to execute this command.
HP2400
HIP interface must be offline. Enter ‘HIP OFF’
The HIP DIAGNOSTIC command was entered. HIP must be
offline to perform diagnostics.
Action
1.
Enter the HIP OFFLINE command.
2.
Reenter HIP DIAGNOSTIC.
HP2410
Abort current transmission; confirm with ‘Y’
This message is a confirmation prompt appearing after the HIP
ABORT command was entered.
Action
Enter Y to abort the job
or
Enter N if abort is not desired.
HP2420
Defer hip diagnostic until OCS queue idle
The HIP DIAGNOSTIC command was entered while a job was
queued or being processed. The command is being ignored.
Action
Wait until all jobs print.
or
Enter the ABORT job command to cancel the job (if only one
remains).
or
1.
Enter the RESET command to delete all jobs.
2.
Reenter the HIP DIAGNOSTIC command to proceed with
diagnostics.
HP2500
Change of job xxxx to file file-type failed: unrecoverable I/O
error yy.
The CHANGE command failed due to the error values specified
in this message. These error values will be one of the following:
•
03 disk controller failed
•
04 disk parity errors
•
10 end of file detected
•
24 device full (insufficient space for the file)
•
26 no such file
•
32 input file read error
•
56 output file write error
•
59 disk device fault (unable to perform operation).
All of the values listed above except 24 will generate an error log
entry.
Action
If value 24 is received, your company’s analyst/programmer
should free up sufficient contiguous system disk space by either
deleting unnecessary files or compressing the disk.
Note: Compressing the disk where the HIPBF.SYS resides should
not be performed because the HIP files will become inaccessible.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-13
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP5000
Host restarted. Trying to reestablish communications
The link to the DMR host was broken and is now reestablished.
HIP is attempting to reestablish communications with the host
and resume from the point where the link was broken.
Action
None.
HP7100
Can not change hosts while jobs are pending or active
Hosts cannot be changed until all jobs are completed.
Action
1.
Wait until active and pending jobs have been printed.
2.
Enter the appropriate HIPHOST command to change hosts.
HP8100
HIP dynamic memory allocation failure: reload
HIP does not have enough memory to continue.
Action
1.
Enter the HIP END command.
2.
Restart HIP or reboot the system.
HP8250
Fatal protocol violation detected
Commands used violate the higher-level software protocols used
to communicate between the 4635 LPS and the host. The host
will be advised to restart communication with the printer. No
data should be lost in this process.
Action
None.
HP9200
Interface failure: unable to receive data
A hardware error has occurred. The system is unable to recover
lost data. The job will abort and the interface will go offline.
Action
1.
Resend the job.
2.
If the error continues, contact your systems specialist or
Xerox Customer Service.
HP9210
Interface failure: failed to go offline
HIP is unable to post the offline status to the XPAF host
computer.
Action
None.
HP9400
HostCLR not received. See host for reason
The HIP DIAGNOSTIC command for interactive diagnostics was
entered. The system failed Test 1: HOSTCLR control line not
verified.
Action
1.
Wait until the diagnostic test is terminated or completed.
2.
Contact your systems specialist or Xerox Customer Service
and give information appearing on the 871-CM display.
4-14
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
HIP (HOST INTERFACE PROCESSOR) MESSAGES
HP9410
Data to host transfer error. See host for reason
The HIP DIAGNOSTIC command was entered. The system failed
Test 2: unable to send a command on OEMI and in turn read the
printer status. The system is terminating the diagnostic test.
Action
1.
Inspect the 871-CM display (the “host” referred to in
message) to learn the nature of the failure.
2.
Contact Xerox Customer Service and give information
appearing on the 871-CM display.
HP9420
Host not communicating. See host for reason
The HIP DIAGNOSTIC command was entered. The system failed
Test 1: (see explanation for message HP9400) or Test 2: system
was unable to send a command on OEMI and in turn read the
printer status.
If Test 2 failed, diagnostics are terminated.
Action
1.
Inspect the 871-CM display (the “host” referred to in the
message) to learn nature of the failure.
2.
Contact Xerox Customer Service and give information
appearing on the 871-CM display.
HP9430
Host timed out in test 3. See host for reason
HIP diagnostic failed.
Action
1.
Reenter the HIP DIAGNOSTIC command to retry the
diagnostic test.
2.
If the problem recurs, contact your systems specialist or
Xerox Customer Service.
HP9431
Line no. n is open
The HIP DIAGNOSTIC command was entered. The system failed
Test 3 which verifies integrity of 8 parallel data lines. The line
number indicated is shorted high.
Action
1.
Inspect the 871-CM display (the “host” referred to in the
message) to learn the nature of the failure.
2.
Contact Xerox Customer Service and give information
appearing on the 871-CM display and in this message.
HP9432
Line no. n is shorted
The HIP DIAGNOSTIC command was entered. The system failed
Test 3 which verifies integrity of 8 parallel data lines. The line
number indicated is shorted to ground.
Action
1.
Inspect the 871-CM display (the “host” referred to in the
message) to learn the nature of the failure.
2.
Contact Xerox Customer Service and give information
appearing on the 871-CM display and in this message.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
4-15
IFU (Interpress font utility)
messages
These messages appear when the Interpress font utility program
(Refer to your 4635 LPS Operations Reference chapter on HIP-
accessed communicating modes for additional information.) The
meaning of terms used in this section can be found in the
Glossary at the back of the message guide.
IF1000
Exit IFU to print
This message advises that you must either exit IFU before
printing your job or IFU is exiting to print a job.
Action
If IFU has not exited to run the print job, enter the END
command to return control to the operating environment and to
invoke the print job.
IF1010
Compiling map xxxx
The requested map is being compiled.
Action
None.
IF1020
Compiling IPFONTS from FIS master xxxx
IPFONTS (Interpress fonts) are being compiled from the
requested FIS master during execution of the ADD command.
Action
None.
IF1021
Compiling DCFONTS from FIS master xxxx
DCFONTS (data center fonts) are being compiled from the
requested FIS master during execution of the ADD command.
Action
None.
IF1030
Family x does not exist in directory
This is an informational message stating that the IPM (Interpress
mapping) file directory does not have the requested font family.
Action
None.
IF1061
Consolidating unreferenced character mapping tables
This is an informational message.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-1
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF1100
Font family xxxx
This is an informational message indicating the font family name
being compiled by the IPFNTS command.
Action
None.
IF1102
Adding xxxx point xxxx
This is an informational message indicating the orientation and
point size are being added to the font mapping structure during
execution of the IPFNTS command.
Action
None.
IF1105
Building font file xxxx : point size n, orientation y
The system is creating a font file with the point size and
orientation shown in the message.
Action
None.
IF1200
Family %0 %1 %2 already exists in directory
The family name of the wanted font is already in the font
directory.
Action
None.
IF1210
Family name specified does not exist in font directory
The family name for a requested font is not in the font directory.
Action
None.
IF1300
Font file xxxx has been deleted
The font file previously marked for deletion by the DELETE
command has been deleted during execution of the COMPRESS
command.
Action
None.
IF1301
WARNING: could not delete the font file xxxx
This warning is given when there is no write access to the file.
Either the user does not have the proper permission or the file
access mode has been changed at some point after the file was
added. It is assumed that the user wants the file left there and is
not deleted from FFM (font file management).
Action
None.
IF1302
Could not find the font file xxxx to delete it
This warning is given when an attempt is made to delete a
particular font file that does not exist on the system.
Action
None.
5-2
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF1410
Start of volume x
This message is displayed at the start of listing a medium's
contents via the IFU medium LIST¦FILE command, when
positioned at the beginning of the medium.
Action
None.
IF1415
Volume x
This message is displayed at the start of listing a medium's
contents via the IFU medium LIST¦FILE command when not
positioned at the beginning of the medium, but at the beginning
of one of the appended written files.
Action
None.
IF1420
Continued on next volume
This message is displayed when listing a medium's contents via
the IFU medium LIST¦FILE command.
Action
None.
IF1421
Continuation volume x
This message is displayed when listing a medium's contents via
the IFU medium LIST¦FILE command.
Action
None.
IF1425
Continuation
This message is displayed when listing a medium's contents via
the IFU medium LIST¦FILE command.
Action
None.
IF1500
Character x requires RIP
The requested character requires RIP (raster image processor),
which is not on your system.
Action
None.
IF1501
Rendered character x requires RIP
The requested rendered character requires RIP (raster image
processor), which is not on your system.
Action
None.
IF1502
Adding as composite bitmap
The requested character is being added as a composite bitmap.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-3
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF1503
Replacing with substitute character
This is an informational message advising that a particular
character is being replaced with the substitute character.
Action
None.
IF1504
Adding as rendered character
The requested character is being added as a rendered character.
Action
None.
IF1600
Consolidating IPM files...
This is an informational message.
Action
None.
IF1601
Consolidating unreferenced character mapping tables
This is an informational message.
Action
None.
IF1602
Deleting unreferenced font files...
This is an informational message.
Action
None.
IF1625
Easy values for FIS font master x are n point orientation: n
resolution: n SPI
This is an informational message providing the easy values for the
specified FIS font master.
Action
None.
IF1626
Comparable name x is y
This is an informational message which provides an equivalent
name for the one requested.
Action
None.
IF1627
Adding font mapping: x
This message provides font mapping that is currently being
inserted into the Interpress font mapping structure.
Action
None.
IF1628
Floppy is not supported
The optional floppy drive is not supported as an IFU input
device.
Action
None.
5-4
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF1629
Parser error
There is a problem with parsing the parameters within a
command.
Action
None.
IF2000
Aborting ADD
The ADD command to add font families to the Interpress or data
center font environments has been aborted.
Action
None.
IF2001
Aborting DCFONTS add
The ADD command to add font families to the DCFONTS (data
center fonts) environment has been aborted.
Action
None.
IF2002
Hardvalues requires RIP option; aborting ADD
Either the point size, orientation, or resolution (hardvalues)
requested does not match what is in the FIS font master
(easyvalues). Requesting hardvalues requires RIP. The ADD
command is therefore being aborted.
Action
None.
IF2005
Terminated. Font profile contains syntax errors
There is a syntax error in the font profile.
Action
Look for possible syntax errors in the font profile and retry the
command.
IF2010
Medium parameter must be a symbol
The part of the command that defines the medium to be used
(tape, floppy, cartridge, etc.) must be written as a single,
acceptable word.
Action
Reenter the statement using an acceptable format.
IF2011
Medium parameter must be TAPE, FLOPPY, or CARTRIDGE
The part of the command that defines the medium to be used
must be either TAPE, FLOPPY, or CARTRIDGE.
Action
Reenter the statement to specify the appropriate medium.
IF2020
Font mask is invalid
In the READ or WRITE statement, the font name mask (complete
font family name) has an invalid parameter.
Action
Reenter the command, using valid parameters in the READ or
WRITE statement.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-5
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2025
Unknown parameter on ADD command
One of the parameters (descriptive elements) in the ADD
command is incorrect.
Action
Check the ADD command and reenter it correctly.
IF2030
Command not recognized
An invalid IFU command has been entered.
Action
Reenter a valid IFU command.
IF2032
Wildcarding not permitted
Wildcarding is not allowed in the Interpress font family name for
this command.
Action
1.
Reenter the command without wildcard characters in the
Interpress font family name.
2.
Retry the command.
IF2036
Wildcarding has found a match
A match has been found with the wildcarded Interpress font
family name requested in the IFU COPY READ command before
end of volume was reached.
Action
Mount the next volume to continue searching
or
Discontinue the operation.
IF2040
MOVE command was stopped by end of volume
During execution of the IFU MOVE command, the number of
files to be moved passed the end of volume.
Action
1.
Enter the IFU medium LIST command to display the number
of items stored on the medium.
2.
Reenter the MOVE command with a valid number of files to
be moved.
IF2042
Invalid number of files have been specified to move
An incorrect number of files to be moved has been given.
Action
Check the number of items on the medium, and enter a valid
number of files to move.
IF2050
Please mount the next volume, number x
This message instructs you to mount the next tape or cartridge
volume. A message will then ask if you want to continue or
abort the operation.
Action
1.
Mount the tape or cartridge number indicated in the
message.
2.
Enter C to continue.
or
Discontinue the operation.
5-6
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2052
The wrong volume has been mounted
The tape or cartridge has been mounted out of sequence. A
message will follow indicating the correct volume to mount and
ask whether you want to continue or quit the operation.
Action
1.
Mount the correct volume.
2.
Enter C to continue.
or
Discontinue the operation.
IF2053
The wrong volume for this volume set has been mounted
The correct volume number has been loaded, but it is not from
the volume set of the previously read volume. A message will
follow indicating the correct volume to mount and ask whether
you want to continue or quit the operation.
Action
1.
Mount the correct volume from the previously read set.
2.
Enter C to continue.
or
Discontinue the operation.
IF2060
Medium not positioned at IFU COPY label. Please reposition
the medium or mount the correct medium
An IFU COPY label is not present to allow processing to begin.
Action
1.
Reposition medium at start of volume if it is the correct
medium
or
mount the correct volume.
2.
Retry the command.
IF2061
Attempting to append to a non IFU COPY medium. Mount
correct medium or initialize the medium and retry
Appending an IFU COPY WRITE file to the end of a non IFU
COPY medium is not permitted.
Action
1.
Mount the correct tape
or
Initialize the medium via the IFU VOLINIT command if the
data on the tape is not needed. (Refer to your 4635 LPS
Operations Reference chapter on managing LPS resources for
additional information.)
2.
Retry the comand.
IF2062
This is an IFU COPY medium but it contains no IFU data.
please mount the correct medium to read
There is no data on the medium to read.
Action
1.
Mount the correct medium with the needed data.
2.
Enter C to continue reading.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-7
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2080
Reading x.
The IFU COPY READ command was reading an Interpress font
family name when end of volume was reached. A message will
follow asking whether you wish to continue searching onto the
next volume or quit the operation.
Action
1.
Mount the next volume.
2.
Enter C to continue reading.
Note: If you elect to quit the operation, a warning message will
follow indicating that exiting execution at this time may corrupt
the font structure on the system.
IF2090
Interpress font was not found
The Interpress font name requested has not been found during
an IFU COPY READ command. A message will follow asking
whether you wish to continue searching onto the next volume or
quit the operation.
Action
Mount next volume to continue searching
or
Discontinue the operation.
IF2098
Are you sure you want to abort? (enter ‘Y’ or ‘N’)
An ABORT command was entered during the IFU COPY READ
process.
Action
Enter N.
Note: The font structure on the disk may be corrupted if the
process is aborted.
IF2099
Aborting at this time may corrupt the font structure
Aborting while reading an Interpress font family name from the
medium onto the system may corrupt the font structure. A
message will follow asking whether you wish to continue
searching onto the next volume or quit the operation.
Action
1.
Mount the next volume.
2.
Enter C to continue the operation.
IF2200
Do you have n floppy disks?
The system is advising you to have enough floppy disks available
to complete the requested IFU COPY FLOPPY WRITE command.
Action
None.
IF2201
Please have n formatted floppies available
The system is advising you to have the given number of
formatted floppy disks available to complete the requested
operation.
Action
None.
5-8
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2210
Floppy dismount has failed
The floppy disk is already dismounted. This is a system problem
that may have occurred between the dismounting of one floppy
disk and the mounting of another.
Action
None.
IF2211
Floppy mount has failed
The floppy may still be mounted due to the premature execution
of a previous IFU COPY command, it may not be ready to be
mounted yet, or it may be faulty.
Action
Retry mounting the same floppy disk or a different one.
or
Reboot the system and reenter the command.
IF2212
The wrong floppy has been mounted
A floppy disk has been mounted out of sequence for reading in.
A message will follow asking if you want to continue or quit this
operation.
Action
Mount the correct floppy if you wish to continue.
or
Discontinue the operation.
IF2220
Please enter the next floppy, number x
Mount the floppy disk next in sequence, as indicated in the
message.
Action
IF2230
Insufficient room on floppy. Please try another floppy.
The floppy disk used does not contain enough space to open a
file to write to during an IFU COPY WRITE command.
Action
1.
Insert a different floppy disk.
2.
Retry the desired activity.
IF2232
Incomplete Interpress font written; missing font files.
When the Interpress font was written to the medium via the IFU
COPY WRITE command, there were missing font files on the
system. The write will complete successfully, but an IFU COPY
READ of this medium will create incomplete Interpress font data
on the system.
Action
1.
Copy the missing font(s) onto the system.
2.
Reenter the IFU COPY WRITE command.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-9
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2233
Incomplete Interpress font read; missing font file(s).
When the Interpress font was written to the medium via the IFU
COPY WRITE command, there were missing font files on the
system. The read will complete successfully, but will not add the
missing font(s) that are mapped to the Interpress font to the
system.
Action
Copy the missing fonts onto the system. Since the missing fonts
are not indicated, use the IFU FIL/EX command on the Interpress
font read to see which fonts were not read in.
IF2234
Output listings of Interpress fonts may be incomplete.
The output file filled during execution of a “wildcarded” IFU LIST
command and some of the Interpress fonts stored on the system
may not be listed.
Action
Retry the operation by entering a number of IFU LIST commands
with specific parameters. This will allow the system to list all
Interpress fonts within each parameter.
IF2235
Please confirm deletion of wildcarded Interpress font
Upon entering the IFU DELETE command, you are asked by the
system to confirm this operation by entering C to continue or A
to abort.
Action
Enter C or A as appropriate.
IF2236
Response was received unsuccessfully!
The operator's response was not received correctly.
Action
None.
IF2237
Package %0 issued unknown message number %1.
This is a general error message.
Action
None.
IF2239
Font x already exists on system, renamed to: y.
During execution of the IFU COPY READ command, the system
is renaming the indicated font before it copies it onto system
disk because a font with the same name already exists on system
disk.
Action
None.
IF2240
Bad line spacing override value was found in font profile.
The line spacing override value is not a numerical value in the
font profile.
Action
1.
Make appropriate changes in the font profile.
2.
Retry the ADD command.
5-10
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2241
FISname not in font profile, using name from FIS master.
The FIS-name parameter in the font profile was omitted. The
name from the FIS master will be used to create the font.
Action
None.
IF2245
Font or character size exceeds standard format.
The font file bitmap size exceeds 1 Megabit or one or more
characters exceed 1024 bits high by 512 bits wide (if viewed in
portrait orientation).
Action
If your system can utilize the 5-word FST format (with version 3
software), set the FTYPE parameter in the font profile to
FTYPE = EXTENDED and retry the ADD process.
or
If your system does not have the 5-word FST format, decrease
the number of characters requested in the CHARS/DCCHARS
parameter in the font profile and retry the ADD process.
IF2250
Medium must be tape or cartridge.
Magnetic tape or cartridge are the only media possible for the
ADD command (some commands do not accept floppy disks).
Action
Reenter the command specifying either magnetic tape or
cartridge.
IF2304
Font profile name is required in ADD command
The ADD command must contain the desired font profile name.
Action
Reenter the ADD command, to include the applicable font profile
name.
IF2306
Font profile x cannot be opened
The requested font profile cannot be opened.
Action
1.
Verify that the font profile exists on the system and that it is
not corrupted.
2.
Reenter the ADD command.
IF2318
Nonnumeric resolution parameter
The resolution of the font must appear numerically as 300 or 600
(spi) in the IPFONTS or DCFONTS statement of the font profile.
Action
1.
Correct the IPFONTS or DCFONTS statement using “300” or
“600” as the resolution parameter in the font profile.
2.
Reenter the ADD command.
IF2324
Pt size x and orient y were not requested; skipping ADD
The expected point size and orientation have not been
requested, and the ADD command will not be processed.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-11
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2330
Character x not found
The character shown in the message cannot be found within the
FIS font master.
Action
1.
Verify that the character requested within the font profile is
the desired character.
2.
Reenter the ADD command.
3.
If the message reappears, contact your systems specialist or
Xerox Customer Support.
IF2332
Composite request (character x) requires RIP
The composite character requested in the font profile requires
RIP (raster image processor), which is not on your system.
Action
None.
IF2336
Map x was not found in IPFNTS.SYS
The requested Interpress character mapping is not found in the
character mapping tables that are stored in the IPFNTS.SYS file.
Action
Modify the font profile to refer to an existing map in the
IPFNTS.SYS file.
IF2342
Operation code must be a symbol
When entering the original command line, the system did not
encounter the READ or WRITE parameter.
Action
Reenter the command line, specifying either a READ or WRITE
parameter.
IF2344
Operation code must be read or write
A READ or WRITE parameter was not specified in the command
line.
Action
Reenter the command line, specifying either a READ or WRITE
parameter.
IF2346
Family xxx not found in family directory
In attempting to delete or list the requested family from the
directory, either the naming authority, character code, or type
style does not exist.
Action
None.
IF2400
FIS name is not in easy value
The font name specified in the FIS font master does not match
the font name specified in the font profile.
Action
None.
5-12
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2402
No CCID parameter has been specified
No CCID (character code identifier) parameter has been specified
in the font profile.
Action
1.
Enter a CCID parameter in the font profile.
2.
Reenter the ADD command.
IF2408
CHARS parameter was not found in IPFONTS statement
The IPFONTS statement in the font profile does not contain the
CHARS (enumeration or range of point sizes) parameter.
Action
1.
Enter the CHARS parameter in the IPFONTS statement of the
font profile.
2.
Reenter the ADD command.
IF2410
Orientation parameter was not found in DCFONTS statement
Orientation (i.e., PORTRAIT, LANDSCAPE, IPORTRAIT, and
ILANDSCAPE) has not been specified in the DCFONTS statement
in the font profile.
Action
1.
Correct the DCFONTS statement to include the desired
orientation parameter.
2.
Retry the ADD command.
IF2412
Point size was not found in DCFONTS statement
Point size is not specified in the DCFONTS statement of the font
profile.
Action
1.
Reenter the DCFONTS sequence to include point size.
2.
Retry the ADD command.
IF2414
Files parameter was not found in DCFONTS statement
No FILES parameter is specified in the DCFONTS statement in the
font profile.
Action
1.
Correct the DCFONTS statement to include the FILE
parameter.
2.
Retry the command.
IF2416
DCCHARS parameter x was not found in DCFONTS statement
The indicated DCCHARS parameter is not included in the
DCFONTS statement of the font profile.
Action
1.
Correct the DCFONTS statement to include the DCCHARS.
2.
Retry the command.
IF2420
Label missing on MAP statement
The MAP statement in the font profile must contain a label.
Action
Reenter the MAP statement to include a label.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-13
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2422
Character mapping table x was not found
The character mapping table needed for the font to be added
does not exist in IPFNTS.SYS.
Action
1.
Compile the correct IPFNTS.JSL with the needed mapping
structure.
2.
Retry the ADD command.
IF2426
Point size x was not found in easy values
The point size requested is not contained within the FIS font
master.
Action
None.
IF2428
Orientation x was not found in easy values
Some orientations requested are not contained in the FIS font
master.
Action
None.
IF2434
Missing name parameter on fonts statement
An Interpress font name is missing from the Interpress fonts
statement in the font profile.
Action
Correct the FONTS statement to include the appropriate name
parameter.
IF2438
FSET parameter x not found
The FSET parameter indicated is missing from the IPFNTS.JSL.
Action
Enter a valid FSET parameter and recompile IPFNTS.
IF2440
Mapping table x was not found in IPFNTS.SYS
The mapping table indicated is not found in the IPFNTS.SYS file.
Action
1.
Recompile the JSL file with the required map.
2.
Retry the command.
IF2448
Missing naming authority in Interpress family name
Interpress naming authority identification is missing from the
command line.
Action
Reenter the command, including the naming authority in the
Interpress family name.
IF2450
Missing character code id in Interpress family
Interpress character code identification is missing from the
command line.
Action
Reenter the command, including the character code ID in the
Interpress family name.
5-14
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2452
Missing typeface style in Interpress family name
Typeface style is missing from the command line.
Action
Reenter the command, including the typeface style in the
Interpress family name.
IF2454
Too many embedded blanks within family name
There are too many spaces in the family name parameter of the
command line.
Action
Reenter the family name parameter of the command sequence to
include an acceptable number of spaces.
IF2456
WARNING: Substitute character requires extended metrics
Substitution of the requested character requires extended
metrics, which may reduce Interpress performance.
Action
None.
IF2701
Syntax error: expecting a comma after x
There is a syntax error in the command line. The system requires
a comma after the item indicated in the message.
Action
Reenter the command to include the needed comma.
IF2702
Syntax error: unexpected comma at end of command
There is a syntax error in the command line that includes an
unnecessary comma at the end of the command.
Action
Reenter the command, omitting the unnecessary comma.
IF2703
Syntax error: expecting (=) after parm
There is a syntax error in the command line. The system requires
an equal sign (=) after the parameter.
Action
Reenter the command to include the “=” sign.
IF2704
Syntax error: incomplete list
There is a syntax error in the command line that includes an
incomplete list of characters or statements.
Action
Reenter the command to include the complete list of required
elements.
IF2705
Syntax error: missing right parenthesis
A right parenthesis is missing from the command line.
Action
Reenter the command to include the missing parenthesis.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-15
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2706
Syntax error: expecting at least one more argument
There is a syntax error in the command line. The system requires
at least one more argument (parameter) in the command
sequence.
Action
Reenter the command to include at least one more parameter.
IF2707
Syntax error: unexpected punctuation
Incorrect punctuation is present in the command line.
Action
Reenter the command using acceptable punctuation.
IF2708
Syntax error: unexpected token x encountered
The character or symbol indicated in the message is incorrectly
included in the command line.
Action
Reenter the command, omitting the incorrect character or
symbol.
IF2709
Syntax error: literal exceeds x characters
The literal (an alphanumeric string not enclosed in single quotes)
exceeds the maximum number of allowable characters.
Action
Reenter the command, using a literal with an allowable number
of characters.
IF2710
Syntax error: hex value is out of range
The command line contains a hexadecimal value that is not within
the allowable range.
Action
Reenter the statement to include hex values that are within the
allowable range.
IF2711
Syntax error: invalid hex value
The command line contains an incorrect hexadecimal value.
Action
Reenter the statement to include an acceptable hex value.
IF2712
Syntax error: unclosed string
A string (sequence of alphanumeric characters treated as a single
unit of data) must be enclosed in single quotes.
Action
Reenter the command to include a string enclosed in single
quotes.
IF2713
Syntax error: string exceeding x characters
The string exceeds the allowable numbers of characters.
Action
Reenter the command to include a string with an allowable
number of characters.
5-16
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2714
Syntax error: invalid character x has been encountered
The command line contains a character that is not allowed.
Action
Reenter the command, using allowable characters.
IF2715
Syntax error: invalid command x has been encountered
The command requested is not allowed.
Action
1.
Verify and reenter the command.
2.
If the message reappears, contact your systems specialist or
Xerox Customer Support.
IF2720
Syntax error in statement x
An error exists in the given statement.
Action
Check and reenter the command, using the corrected statement.
IF2730
Semantic error in statement x
An error exists in the meaning of the statement as formatted.
Action
Check and reenter the command, using the corrected statement.
IF2790
Parser error: next _ charcalled with invalid mode
An error has occurred while the system was reading the
command line. This could be the result of a previous syntax
error in the command line.
Action
Check the command syntax and retry.
IF2791
Parser error: invalid next _ char (2) call
An error has occurred while the system was reading the
command line. This could be the result of a previous syntax
error in the command line.
Action
Check the command syntax and retry.
IF2805
Invalid medium parameter
The statement that defines the source (TAPE, CASSETTE, DISK,
FLOPPY) of the FIS master is incorrect.
Action
Check and reenter the command using an allowable type of
medium.
IF2850
Invalid LPS seed parameter
The statement defining the LPS seed name (the base or root of
the name) of the newly created font file is incorrect.
Action
1.
Verify the seed name in the LPS seed name parameter in the
font profile, and reenter the command.
2.
If the message reappears, contact your systems specialist or
Xerox Customer Support.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-17
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2851
Invalid default font name
The default substitution font requested is incorrect.
Action
Check and reenter the DEFAULT statement using an acceptable
font name.
IF2852
Invalid FTYPE parameter
The FTYPE parameter in the font profile is incorrect.
Action
1.
Reenter the FTYPE parameter to include the correct
parameter (either STANDARD or EXTENDED).
2.
Retry the ADD command.
IF2853
Invalid Interpress family name
The Interpress family name requested is incorrect.
Action
Reenter the command to include the family name statement with
the correct syntax.
IF2854
Invalid mapping parameter on fonts statement
The mapping parameter contained in the FONTS statement of the
IPFNTS command sequence is not allowed.
Action
1.
Reenter the command to include an acceptable mapping
parameter in the FONTS statement.
2.
If the message reappears, contact your systems specialist or
Xerox Customer Support.
IF2856
Invalid name parameter on fonts statement
The NAME parameter in the JSL file is incorrect.
Action
Enter the correct NAME parameter in the JSL file.
IF2857
Invalid printer name in the IPFONTS statement
The printer name entered in the CREATOR statement in the font
profile is incorrect.
Action
1.
Correct the CREATOR statement in the font profile with an
appropriate printer name.
2.
Retry the command.
IF2858
Invalid printer name
The printer name entered in the printer command is incorrect.
Action
Check and reenter the appropriate printer name in the command.
IF2859
Invalid resolution parameter on fonts statement
The resolution requested (300 or 600 spi) in the fonts statement
in the JSL file is incorrect for your system’s configuration.
Action
1.
Correct the resolution parameter in the FONTS statement in
the JSL file.
2.
Retry the command.
5-18
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2860
Invalid sections parameter
The section parameter in the GENERAL statement of the font
profile is incorrect.
Action
1.
Verify and reenter the appropriate sections parameter in the
font profile.
2.
Reenter the ADD command.
IF2861
Invalid substitution parameter
The requested SUBSTITUTION parameter in the PROFILE
statement of the font profile is incorrect.
Action
1.
Verify and reenter the command to include the appropriate
SUBSTITUTION parameter.
2.
Reenter the ADD command.
IF2862
Invalid density switch
Only 1600 and 6250 densities are valid.
Action
None.
IF2863
Invalid font mask in command
The Interpress font name requested in the command is incorrect.
Action
1.
Verify and reenter the command to include the appropriate
Interpress font name.
2.
If the message reappears, contact your systems specialist or
Xerox Customer Support.
IF2864
Invalid statement found in font profile
An incorrect statement exists in the font profile.
Action
Verify all statements and reenter the command correctly.
IF2901
JSL syntax err x- literal exceeding y chars
A literal in the JSL file exceeds the permissible number of
characters.
Action
1.
Correct the JSL file to include a permissible literal.
2.
Retry the command.
IF2902
JSL syntax err x - invalid hex value
An incorrect hexadecimal value exists in the JSL file.
Action
1.
Correct the JSL file to include a correct hex value.
2.
Retry the command.
IF2903
JSL syntax err x - unclosed string
There is an unclosed string in the JSL file.
Action
1.
Correct the JSL file to include a string enclosed in single
quotes.
2.
Retry the command.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-19
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2904
JSL syntax err x string exceeding y chars
The JSL file string exceeds the allowable number of characters.
Action
1.
Correct the JSL file to include a string with an allowable
number of characters.
2.
Retry the command.
IF2905
JSL syntax err x - invalid character (/)
The JSL file contains a character that is not allowed by the
system.
Action
1.
Correct the JSL file, using allowable characters.
2.
Retry the command.
IF2906
JSL syntax err x - unclosed comment
The JSL file contains an incomplete comment, i.e., it is offset by
“/*” and “*/” .
Action
1.
Correct the JSL file, using correct syntax for the comment.
2.
Retry the command.
IF2907
JSL syntax err x - invalid character y
The JSL file contains a character that is not allowed.
Action
1.
Correct the JSL file, using allowable characters.
2.
Retry the command.
IF2908
JSL syntax err x - expecting literal value
The system requires a value to follow the literal in the JSL file.
Action
1.
Correct the JSL file to include a literal value.
2.
Retry the command.
IF2909
JSL syntax err x - missing asemi-colon
A semi-colon is missing from the JSL file.
Action
1.
Correct the JSL file to include the missing semi-colon.
2.
Retry the command.
IF2910
JSL syntax err x - expecting an equal sign after y
The system requires an equal sign (=) after the given character in
the JSL file.
Action
1.
Correct the JSL file to include the required equal sign.
2.
Retry the command.
IF2911
JSL syntax err x - unexpected punctuation y
There is incorrect punctuation in the JSL file.
Action
1.
Correct the JSL file, omitting the unneeded punctuation.
2.
Retry the command.
5-20
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2912
JSL syntax err x - missing right parenthesis
A right parenthesis is missing from the JSL file
Action
1.
Correct the JSL file to include the missing parenthesis.
2.
Retry the command.
IF2913
JSL syntax err x - invalid JSL statement y
There is an incorrect statement in the JSL file.
Action
1.
Correct the JSL file.
2.
Retry the command.
IF2914
JSL syntax err x - invalid JSL parameter y
There is an incorrect parameter in the JSL file.
Action
1.
Correct the JSL file.
2.
Retry the command.
IF2915
JSL syntax err x - invalid ASCII value
An incorrect value has been assigned to the ASCII element of the
id:CODE statement of the JSL file.
Action
1.
Correct the JSL file to include correct ASCII values.
2.
Retry the command.
IF2916
Rendered subcharacter is not specified in font profile
One or more subcharacter component(s) of a rendered character
has not been specified within the font profile.
Action
1.
Add the appropriate character(s) to the font profile CHARS
statement.
2.
Reenter the ADD command.
IF2950
JSL file x will not open
The requested JSL file in the IPFNTS statement cannot be
opened.
Action
Verify and reenter the JSL file name correctly.
IF2951
JSL statement is too large to be processed
The JSL statement in the JSL file is too large for the system to
process.
Action
1.
Modify the JSL file to include more semi-colons to indicate
the end of statements.
or
Shorten the statements, if possible.
2.
Retry the command.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-21
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2960
JSL parse err x - unexpected token type (y, z)
A character or symbol is included in the JSL file that the system
cannot read.
Action
1.
Correct the JSL file, omitting any incorrect elements.
2.
Retry the command.
IF2970
Invalid hardvalues parameter.
An invalid value was assigned to the HARDVALUES parameter in
the font profile.
Action
1.
Change the HARDVALUES parameter in the font profile to
YES or NO.
2.
Reenter the ADD command.
IF2971
Bad CHARS parameter
The CHARS parameter in the font profile contains invalid syntax.
Action
1.
Correct the syntax of the CHARS parameter.
2.
Reenter the ADD command.
IF2972
Bad COMPOSITES parameter.
The COMPOSITES parameter in the font profile contains
incorrect syntax.
Action
1.
Correct the syntax of the COMPOSITES parameter in the font
profile.
2.
Reenter the ADD command.
IF2973
No valid characters were found in character set x
In processing the FIS master, the substitute character's raster
bitmap is either missing or defective.
Action
1.
Correct the CHARS parameter of the font profile.
2.
Reenter the ADD command.
IF2974
Character x is in the system reserved area
No characters may be added in the range 0-208 or 0-20 (octal).
These positions are reserved for system use.
Action
1.
Remove the invalid characters from the CHARS parameter in
the font profile.
2.
Reenter the ADD command.
IF2975
Contour fonts require RIP option; aborting ADD
The FIS master contains contour character shapes which require
the RIP option.
Action
None.
5-22
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF2976
Some parameter(s) are not in easy values.
One or more of the parameters specified in the font profile do
not match the easy values of the FIS font master.
Action
1.
Correct the font profile to match the easy values.
2.
Reenter the ADD command.
IF2979
Invalid DCALSO parameter.
The DCALSO (DATA CENTER ALSO) parameter specified in the
font profile is incorrect.
Action
1.
Change the DCALSO parameter in the font profile to YES or
NO.
2.
Retry the ADD command.
IF4010
Easy values are missing point sizes or orientations
The FIS master is incorrectly formatted and, therefore, does not
specify point sizes and orientation.
Action
None.
IF4110
FIS master error; aborting ADD
Due to an error in the FIS master, the requested ADD command
is being aborted.
Action
1.
Obtain a valid FIS master.
2.
Retry the command.
IF4111
FIS processing error; aborting ADD
Due to an error in the FIS master, the ADD command is being
aborted. This error is probably the result of a previous error
which should have displayed a message.
Action
Contact your systems specialist or Xerox Customer Service.
IF4112
Unable to create a font file, x; aborting ADD.
An error has occurred when the system attempted to access the
font file. The ADD command has been aborted.
Action
None.
IF4120
Easy values are invalid. fatal error in Interpress
A fatal Interpress error occurred while an FIS master was being
processed. The Interpress error appears on the system controller
display before this IFU message.
Action
1.
Correct the FIS master.
2.
Reenter the ADD command.
IF4121
Easy values are invalid. fatal error in FIS master.
An error occurred during processing of an FIS master.
Action
1.
Correct the FIS master.
2.
Reenter the ADD command.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-23
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF4122
Character is missing at least one extent.
The FIS master lacks sufficient information to complete the ADD
process for this character.
Action
1.
Correct the FIS master.
2.
Reenter the ADD command.
IF4123
Substitute character bitmap is bad or missing.
During processing of the FIS master, the substitute character's
raster bitmap was found to be either missing or defective.
Action
None.
IF4124
Rendered subcharacter is bad or missing.
One or more subcharacter component(s) of a rendered character
is either defective or not in the FIS master.
Action
1.
Correct the FIS master.
2.
Reenter the ADD command.
IF7000
** - WRITE LOCK PROTECTION ERROR - **
A write operation could not be completed successfully, probably
because the write ring is not present on the magnetic tape.
Action
1.
Put a write enable ring on the magnetic tape. (Refer to your
4635 LPS Operator Guide.)
2.
Retry the command.
IF7100
Can‘t find IFUFSN.SYS; resysgen and retry ADD
The IFUFSN.SYS file, which contains default font information, was
not found on the system disk. (Refer to your 4635 LPS System
Generation Guide.)
Action
1.
If authorized to do so, resysgen.
2.
Retry the ADD command.
IF7101
Font file x will not open
The requested font file is not on the system.
Action
Copy the missing font onto the system.
IF7102
IPFNTS.SYS file will not open
The IPFNTS.SYS file is not on the system.
Action
Create a new IFU IPFNTS.SYS file by executing the IFU IPFNTS
command.
5-24
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF7104
IPFNTS.SYS open error
The system is unable to access the IPFNTS.SYS file.
Action
Create a new IFU IPFNTS.SYS file by executing the IFU IPFNTS
command.
IF7105
Output file will not open
The medium specified (tape, disk, etc.) does not contain the
external file requested
Action
Verify the file name and, if it exists on the medium, reenter the
command. (Refer to your 4635 LPS Operations Reference
chapter on managing LPS resources for additional information.)
IF7106
Print file will not open
The IFU LIST command cannot open the .DAT print file to
process. This is probably a disk error.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF7108
Temporary file x of decomposed FIS will not open
There is an IFU temporary access problem, probably due to a
disk error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7109
JSL storage request has failed.
An error occurred when requesting memory for the IPFNTS.JSL
file. This is probably due to a disk error or insufficient disk
space.
Action
1.
Compress the disk and retry the command.
2.
If the message reappears, contact your systems specialist or
Xerox Customer Service.
IF7701
Error generating font file x; aborting ADD
There is a font profile access problem, probably due to a disk
error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7702
Error processing the font profile
There is a font profile access problem, probably due to a disk
error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-25
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF7703
Error processing temporary font profile
There is an IFU temporary access problem, probably due to a
disk error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7704
Family name directory is out of space
There is no more space in the FDR file. This is a software
limitation problem.
Action
Contact your systems specialist or Xerox Customer Service.
IF7705
Family name directory will not open
The FDR package is either not on the system or is corrupted
Action
Execute the IFU IPFNTS command sequence to recreate the FDR
file.
IF7800
Interpress decomposer initialization error
There is insufficient memory to initialize IPD.
Action
Contact your systems specialist or Xerox Customer Service.
IF7801
Interpress mapping file package ADD function failed
An error occurred when adding an entry to the IPM (Interpress.
mapping), probably due to a disk error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7802
Interpress mapping package failure
An error occurred when accessing the IPM file, probably due to a
disk error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7803
Character mapping table package error
An error occurred when the system was processing the character
mapping table package, probably due to a disk error or
insufficient space.
Action
Contact your systems specialist or Xerox Customer Service.
IF7804
Character mapping table package will not open
The system is unable to access the character mapping table
package, probably due to a disk error or insufficient space.
Action
Contact your systems specialist or Xerox Customer Service.
5-26
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF7901
CMT failed during IPF call x
CMT (character mapping table) could not be read from the
IPFNTS.SYS file. Either IPFNTS does not exist on the system or
the file is corrupted.
Action
1.
Check if the IPFNTS.SYS file is on the system.
2.
If IPFNTS.SYS is on the system, the file is corrupted.
Recompile the IPFNTS.JSL to replace the corrupted
IPFNTS.SYS file.
IF7902
CMT package error
An error occurred while the system was processing the character
mapping table, probably due to a disk error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7903
FFM ADD command failed on file x
The font file management ADD command has failed on the
requested file.
Action
1.
Retry the ADD command.
2.
If the message reappears, contact your systems specialist or
Xerox Customer Service.
IF7904
FFM package will not open
The system is unable to open the IFUFFM.SYS file, probably due
to a disk error.
Action
1.
Check if the IFUFFM.SYS file is on the system.
2.
If IFUFFM.SYS is on the system, the file is probably
corrupted. Delete the IFUFFM.SYS file and retry the ADD
command to recreate the FFM file.
IF7905
GTMU allocation of font request memory failed
The system is unable to get adequate memory for the requested
font, probably due to a disk error or insufficient space.
Action
1.
Compress the disk and retry the command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7907
IPM package will not open
The system cannot open the IPM package, probably due to a
disk error.
Action
1.
Delete the IPM files on the system and recompile the
IPFNTS.JSL to recreate the IPM files.
2.
Retry the command.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-27
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF7908
MAPM of font request memory failed
The request for mapping memory failed due to insufficient
available memory.
Action
None.
IF7909
SAMPLE command failed, retry
The command file IFSAM$.CMD, used to print out the fonts
specified in the SAMPLE command, does not exist because the
FOPEN command failed. This is a probable disk error.
Action
Contact your systems specialist or Xerox Customer Service.
IF7910
IPM FDR routine x has failed
An error occurred while accessing the file directory (FDR),
probably due to a disk error.
Action
1.
Check if the IFUFDR.SYS file is on the system.
2.
If IFUFDR.SYS is on the system, the file is corrupted and
should be deleted.
3.
Recompile IPFNTS.SYS to recreate this file.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7911
IPM error
IPM would not open because it is either not on the system or
the file is corrupted.
Action
1.
Delete the IPM files on the system.
2.
Recompile IPFNTS.SYS to recreate this file.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF7912
IPM FCLOSE of file x has failed
An attempt is being made to close an IPM file that is already
closed or an IPM file that is corrupted, probably due to a disk
error.
Action
1.
Delete the IPM files on the system.
2.
Recompile IPFNTS.SYS to recreate this file.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7913
IPM FOPEN of file x has failed
An attempt is being made to open an IPM file that is already
open.
Action
1.
Delete the IPM files on the system.
2.
Recompile IPFNTS.SYS to recreate this file.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
5-28
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF7914
IPM input from file x, block y, failed
The system failed in an attempt to read a block from an IPM file.
The file is either corrupted or does not exist on the system.
Action
1.
Delete the IPM files on the system.
2.
Recompile IPFNTS.SYS to recreate this file.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7915
IPM more than 1000 files are needed for x
Allocation is being attempted from the free blocks list but there
are not enough free blocks to store the family. On the one-
thousandth file, this allocation will fail due to file sequence
wraparound.
Action
None.
IF7916
IPM package error
IPM would not open. The IPM file is either missing from the
system or is corrupted.
Action
1.
Delete the IPM files on the system.
2.
Recompile IPFNTS.SYS to recreate this file.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7930
Error occurred while reading decomposed FIS file.
A disk input/output error occurred while the system was
accessing an internal temporary file.
Action
1.
Reenter the ADD command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF7931
Error occurred while accessing the CMT block
An IFU internal error has occurred.
Action
None.
IF8101
CMT calling sequence error x
The character mapping table is being processed out of sequence.
Action
Contact your systems specialist or Xerox Customer Service.
IF8102
CMT storage request has failed
The amount of storage space requested is too large.
Action
Contact your systems specialist or Xerox Customer Service.
IF8103
CMT symbol table has overflowed by map x
There was not enough space in the character mapping table
when adding the next symbol.
Action
Contact your systems specialist or Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-29
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8104
CMT entry table has overflowed by map x
There was not enough space in the character mapping table
when adding the next entry.
Action
Contact your systems specialist or Xerox Customer Service.
IF8105
CMT insufficient room in disk file (MAP x )
There is insufficient disk space for the requested character
mapping table.
Action
Contact your systems specialist or Xerox Customer Service.
IF8106
CMT mapping x too big
The size of the indicated mapping exceeds the maximum size.
Action
Contact your systems specialist or Xerox Customer Service.
IF8201
Error: from IPM_open ( )
The system is unable to open an IPM file.
Action
1.
Delete all IPM files from the system.
2.
Recompile IPFNTS.JSL to recreate the IPM files and retry the
command.
3.
If the message reappears, contact your systems specialist or
Xerox Customer Support.
IF8202
Error: from FFM_open ( )
The system is unable to open the IFUFFM.SYS file (font file
management). Either the IFUFFM.SYS file is not on the system or
it is corrupted.
Action
1.
If IFUFFM.SYS is on the system, it is corrupted and should be
deleted.
2.
Retry the ADD command.
3.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF8203
Error: from IPF_open ( )
The system is unable to open the IPFNTS.SYS file. Either the file
is not on the system or is corrupted or there is a software
problem.
Action
1.
Check if the IPFNTS.SYS file is on the system.
2.
If IPFNTS.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
5-30
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8204
Error: from DLM_open ( )
The system is unable to open the IFUDLM.SYS file. Either the file
is not on the system or is corrupted, or there is a software
problem.
Action
1.
Check if the IFUDLM.SYS file is on the system.
2.
If IFUDLM.SYS is on the system, it is corrupted and should
be deleted.
3.
Retry the command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF8205
Error: from IPM_set_family_mask ( )
The IPM file is being processed out of sequence.
Action
Contact your systems specialist or Xerox Customer Support.
IF8207
Error: from IPM_set_font_mask ( )
The IPM file is being processed out of sequence.
Action
Contact your systems specialist or Xerox Customer Support.
IF8208
Error: from IPM_next_font_entry ( )
The IPM file is being processed out of sequence.
Action
Contact your systems specialist or Xerox Customer Support.
IF8209
Error: from FFM_mark_ref ( ) entry ( )
An error occurred when the system attempted to access the
IFUFFM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUFFM.SYS file is on the system.
2.
If IFUFFM.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
F8210
Error: from IPF_read_block ( ) entry ( )
An error occurred when the system attempted to access the
IPFNTS.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IPFNTS.SYS file is on the system.
2.
If IPFNTS.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-31
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8211
Error: from IPF_WRITE_BLOCK ( ) ENTRY ( )
An error occurred when the system attempted to access the
IPFNTS.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IPFNTS.SYS file is on the system.
2.
If IPFNTS.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8212
Error: from FFM_FIND_NEXT ( )
An error occurred when the system attempted to access the
IFUFFM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUFFM.SYS file is on the system.
2.
If IFUFFM.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8213
Error: from FFM_READ_CURRENT ( )
An error occurred when the system attempted to access the
IFUFFM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem
Action
1.
Check if the IFUFFM.SYS file is on the system.
2.
If IFUFFM.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8214
Error: from DLM_ADD ( )
An error occurred when the system attempted to access the
IFUDLM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUDLM.SYS file is on the system.
2.
If IFUDLM.SYS is on the system, it is corrupted and should
be deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
5-32
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8215
Error: from FFM_CURR_FONT _REF ( )
An error occurred when the system attempted to access the
IFUFFM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUFFM.SYS file is on the system.
2.
If IFUFFM.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8216
Error: from DLM_REWIND ( )
An error occurred when the system attempted to access the
IFUDLM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUDLM.SYS file is on the system.
2.
If IFUDLM.SYS is on the system, it is corrupted and should
be deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8217
Error: from DLM_READ_SEQ ( )
An error occurred when the system attempted to access the
IFUDLM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUDLM.SYS file is on the system.
2.
If IFUDLM.SYS is on the system, it is corrupted and should
be deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8218
Error: from FFM_Delete ( )
An error occurred when the system attempted to access the
IFUFFM.SYS file. Either the file is not on the system or is
corrupted, or there is a software problem.
Action
1.
Check if the IFUFFM.SYS file is on the system.
2.
If IFUFFM.SYS is on the system, it is corrupted and should be
deleted.
3.
Retry the ADD command.
4.
If the problem continues, contact your systems specialist or
Xerox Customer Service.
IF8301
IPM calling sequence error x
The IPM file is being processed out of sequence.
Action
Contact your systems specialist or Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-33
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8302
IPM disk family x is too big
In an IFU IPFNTS command, this IPM name is too large to be
added to the IPM file on the system.
Action
1.
Alter the JSL file if necessary, to specify a smaller IPM family
to be compiled.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF8303
IPM family is too large: x
In an IFU IPFNTS command, this IPM name is too large to be
added to the IPM file on the system.
Action
1.
Alter the JSL file if necessary, to specify a smaller IPM family
to be compiled.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF8304
IPM storage request has failed
The amount of storage space requested is too large.
Action
Contact your systems specialist or Xerox Customer Service.
IF8307
Interpress decomposer easy value error
There has been an error when reading easy values from the input
media.
Action
Contact your systems specialist or Xerox Customer Service.
IF8401
FIS font request failed with EMT return code x
The FIS font request cannot be processed due to the EMT
(emulator trap) return code shown.
Action
Contact your systems specialist or Xerox Customer Service.
IF8402
FIS initiation failed with EMT return code x
Initiation of FIS cannot be processed due to the EMT return code
shown.
Action
Contact your systems specialist or Xerox Customer Service.
IF8403
FIS termination failed with EMT return code x
FIS termination cannot be processed due to the EMT return code
shown.
Action
Contact your systems specialist or Xerox Customer Service.
IF8404
Font set is larger than Font_Set_Array_size limit
There is not enough memory to process the font set.
Action
Contact your systems specialist or Xerox Customer Service.
5-34
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8405
IPD communication failure; aborting ADD
IPD communication is not operational. The ADD command has
been aborted.
Action
Contact your systems specialist or Xerox Customer Service.
IF8406
Incorrect floppy logical unit
The logical unit assigned to the device does not check out
correctly.
Action
1.
Retry the command.
2.
If this fails again, reboot the system and retry the command.
IF8408
Missing block header on medium to read
The text that was just read from the written file on the medium
was not as expected. The format of the file written by the WRITE
command is either corrupted, the READ and WRITE codes are
not being executed synchronically, or a noncopy medium was
loaded when a READ was attempted.
Action
Remount the medium (tape, floppy, etc.), making sure it is the
correct medium for a READ
or
Execute the corresponding WRITE command again for the READ
that failed.
IF8409
Missing font mapping header at file offset?
The text that was just read from the written file on the medium
was not as expected. The format of the file written by the WRITE
command is either corrupted, the READ and WRITE codes are
not being executed in sync, or a noncopy medium was loaded
when a read was attempted.
Action
Remount the medium (tape, floppy, etc.), making sure it is the
correct medium for READ.
or
Execute the corresponding WRITE command again for the READ
that failed.
IF8410
Tape file buffering has failed
There is an error in the system call.
Action
1.
Retry the operation.
2.
If the retry fails, reboot the system.
IF8420
Internal buffer allocation failed, aborting ADD.
Memory allocation for a font file has failed.
Action
Contact your systems specialist or Xerox Customer Service.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-35
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF8500
Decomposed FIS file has bad syntax.
An error occurred while the system was processing an internal
temporary file.
Action
1.
Reenter the ADD command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF8501
Fatal error has been detected in font request
An error occurred while the system was processing the font
request.
Action
1.
Reenter the ADD command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF8502
Character x returned error code y.
A character in the decomposed FIS caused an error code to
appear.
Action
1.
Reenter the ADD command.
2.
If the problem continues, contact your systems specialist or
Xerox Customer Support.
IF9000
**- DEVICE IS NOT READY -**
The medium specified was not available when the operation was
attempted, or during the operation.
Action
1.
Prepare the medium for operation and retry the command.
2.
If the retry fails, replace the media and retry.
IF9001
**- END OF FILE HAS BEEN DETECTED -**
An end of file (tape mark) has been encountered.
Action
None.
IF9002
**- END OF VOLUME HAS BEEN DETECTED -**
The logical end of volume was detected during the task
execution. The tape is left positioned between the two tape
marks. (This condition is not detected during the read
operations.)
Action
Reposition the medium to the beginning of where the WRITE
operation should start and retry the operation.
IF9003
**- DEVICE IS FULL (FCP) -**
This message indicates an attempt to write to a medium that is
full.
Action
None.
5-36
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF9004
**- NO SUCH FILE -**
The file being accessed does not exist.
Action
None.
IF9005
**- FATAL HARDWARE ERROR -**
A fatal and unrecoverable hardware error has occurred during the
operation. For example, a bad block detected on the medium is
being used.
Action
Contact your systems specialist or Xerox Customer Service.
IF9006
**- FATAL DEVICE ERROR -**
A serious error has occurred on the medium.
Action
1.
Select the abort option when the display prompts you to
choose retry, ignore, or abort.
2.
Contact your systems specialist or Xerox Customer Service.
IF9007
**- TAPE UNIT IS offline-**
The magnetic or cartridge tape is not online.
Action
1.
Place the magnetic medium in the online operating mode.
2.
Retry the job.
IF9099
Device error x
An input/output operation on the medium failed.
Action
Refer to the error message appearing on the system controller
keyboard display and take appropriate action.
IF9101
Read error on IPFNTS.SYS
The system is unable to read font files and mappings from the
IPFNTS.SYS file. (Same as IF9103.)
Action
Create a new IPFNTS.SYS file by executing the IPFNTS command.
IF9102
Write error on IPFNTS.SYS
The system is unable to write data from an external media to the
IPFNTS.SYS file. (Same as IF9105.)
Action
Create a new IPFNTS.SYS file by executing the IPFNTS command.
IF9103
Read error on IPFNTS.SYS
The system is having a problem reading font files and mappings
from the IPFNTS.SYS file. (Same as IF9101.)
Action
Create a new IPFNTS.SYS file by executing the IPFNTS command.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
5-37
IFU (INTERPRESS FONT UTILITY) MESSAGES
IF9104
IPFNTS.SYS read error
The system is having a problem reading font files and mappings
from the IPFNTS.SYS file.
Action
Create a new IPFNTS.SYS file by executing the IPFNTS command.
IF9105
Write error on IPFNTS.SYS
The system is having a problem writing data to the IPFNTS.SYS
file. (Same as IF9102.)
Action
Create a new IPFNTS.SYS file by executing the IPFNTS command.
IF9914
IPM output to File x, Block x, failed
An attempt to read from the IPM file has failed, probably due to
a disk error.
Action
1.
Delete the IPM files from your system.
2.
Recompile the IPFNTS.JSL file to recreate the IPM files.
3.
Retry the command.
5-38
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6. OSS (operating system software)
messages
The OS messages appearing on your system controller display are
generated by the operating system software (OSS). These
messages are assigned to levels 0 through 9. The higher the
number, the more serious the problem or condition being
reported. The first digit after “OS” indicates the message level.
For example, OS7210 is a Level 7 message. Your 4635 LPS
Operator Guide and 4635 LPS Operations Reference provide
detailed information about LPS operations and related messages.
OS Level 0: Confirmation
Confirms that the 4635 LPS is responding.
OS0010
Resuming input
The CONTINUE or CONTINUE I command was entered, or the
key was pressed. System is reading data onto the
system disk.
Action
None.
OS0020
Resuming output
The CONTINUE or CONTINUE O command was entered, or the
key was pressed. The system is printing data from the
system disk.
Action
None.
OS0030
System is “ONLINE”
The ONLINE command was entered. The system is ready to
receive data through a host channel.
Action
None.
OS0040
System is “OFFLINE”
The OFFLINE command was entered. The system is not
connected to a host channel and is not able to receive data from
a host.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-1
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0060
Resuming full performance
The printer had been operating in a reduced performance mode
due to page complexity and is now returning to full performance.
Action
None.
OS0200
Main tray selected
This message confirms that the main tray (paper tray 1) has been
selected.
Action
None.
OS0201
Cluster xx selected trays: xxxxx
In response to a FEED cluster-name command, this confirms that
the cluster is selected and provides a list of feeder trays in the
named cluster.
Action
None.
OS0202
Cluster xx selected ***cluster has no current trays***
In response to a FEED cluster-name command, this confirms that
the cluster is selected and that the cluster has no feed trays
currently assigned to it.
Action
None.
OS0211
Paper tray xx selected
In response to a FEED tray-number command, this confirms that
the specified feeder tray is selected.
Action
None.
OS0250
Sample tray selected
In response to a SELECT TRAY command, this confirms that the
sample tray is now selected.
Action
None.
OS0310
Bin x selected
One of the following commands was entered:
—SELECT
—SELECT 1
—SELECT AUTO
—SELECT 1,SAMPLE
Output will be delivered to stacker bin x.
Action
None.
6-2
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0320
Output tray 2 selected
One of the following commands was entered:
—SELECT
—SELECT 2
—SELECT AUTO
—SELECT 2,SAMPLE
Output will be delivered to stacker tray 2.
The printer control console displays:
Output tray 2 selected
Action
None.
OS0410
Separate is OFF
The SEPARATE OFF command was entered, cancelling the
previously entered SEPARATE command.
Action
None.
OS0411
Stitch is OFF
Confirms a STITCH OFF command.
Action
None.
OS0420
Separate is ON
The SEPARATE command was entered. The system will switch
output to a currently inactive stacker tray at the start of the next
report.
Action
None.
OS0430
Set command accepted
Confirms a CLUSTER SET command. (This includes CLUSTER
SET/NR, CLUSTER cluster-name SET, or CLUSTER cluster-name
SET/NR commands.)
Action
None.
OS0500
Output stopped
The STOP or STOP O command was entered or the
key was pressed. Printing has stopped. (Input continues.)
Action
To restart:
Enter CONTINUE or CONTINUE O
or
Press the key.
OS0510
Input stopped
The STOP or STOP I command was entered, or the key
was pressed. The system has stopped transmitting data and is
reading it onto the system disk.
Action
To restart:
Enter CONTINUE or CONTINUE I command
or
Press the key.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-3
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0610
Page spacing forward
The SPACE n PAGES command was entered. The system is
skipping forward over a specified number of pages in the current
job.
Action
None.
OS0620
Page spacing backward
The SPACE -n PAGES command was entered. The system is
skipping backward over a specified number of pages in the
current job.
Action
None.
OS0630
Page spacing complete.
Total pages spaced: xx
Simplex data pages: xx.
Simplex nondata pages: xx
Duplex data pages: xx.
Duplex nondata pages: xx
Confirms that a SPACE n PAGES command has completed.
Action
None.
OS0700
Cluster xx now deleted
A command was entered that caused both the current and the
preferred lists of feeder trays for the cluster to be empty. The
cluster has been deleted from the internal database.
Action
None.
OS0720
Paper tray not found in any cluster
CLUSTER n or CLP n was entered, but the specified feeder tray
was not found in any cluster.
Action
Check the cluster and assign a valid feeder tray. (Refer to your
4635 LPS Operations Reference chapter on setting up print jobs
for additional information.)
OS0730
Finishing exerciser utility: Successful Exit.
FEX has successfully completed.
Action
None.
OS0731
Updating the IOT‘S memory with test profile info
FEX is loading into the printer‘s non-volatile memory the new
finishing parameters profile you have specified.
Action
None.
OS0732
Finishing exerciser is starting requested print job
FEX has created the test job and is starting to run it.
Action
None.
6-4
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0731
Updating the IOT‘S memory with test profile info
FEX is loading into the printer‘s non-volatile memory the new
finishing parameters profile you have specified.
Action
None.
OS0732
Finishing exerciser is starting requested print job
FEX has created the test job and is starting to run it.
Action
None.
OS0733
Finishing exerciser utility (FEX) starting . . .
The system responds with this message after you have entered
the FEX command.
Action
None.
OS0734
Finishing exerciser utility: working . . .
FEX is in communication with the printer.
Note:
This message may appear numerous times during the FEX
session.
Action
None.
OS0800
NVM update in progress
****DO NOT DISTURB****
The periodic acquisition of information from the printer control
console is in progress.
Action
Do not disturb.
OS0801
NVM update complete
The periodic acquisition of information from the printer control
console has been completed.
Action
None.
OS0830
Attention Light enabled.
The LIGHT ENABLE command is entered and accepted.
Action
None.
OS0831
Attention Light disabled.
The LIGHT DISABLE command is entered and accepted.
Action
None.
OS0840
Entering Lockout Mode
The lockout diagnostic mode is active.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-5
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0845
Exiting Lockout mode
The lockout diagnostic mode has been terminated.
Action
None.
OS0850
Print Quality Adjustment pending
This message is displayed after you have entered a valid PQA
command and usually accompanies other related messages.
Action
Enter the CONTINUE command, or press the key to
initiate PQA.
OS0851
Paper tray: x Output tray: n
This message identifies the paper and output tray numbers
involved in the current PQA operation and may accompany other
related messages.
Action
None.
OS0852
Cluster: xxxxx Output tray: n
This message identifies the cluster name and output tray number
involved in the current PQA operation and may accompany other
related messages.
Action
None.
OS0853
Mode: xxx housing, -plex
During PQA, this message identifies the housings being adjusted
and whether simplex or duplex printing is specified for the
current PQA operation. This message may accompany other
related messages.
Action
None.
OS0854
After Print Quality
Adjustment: continue printing
automatically
This message specifies that when print quality adjustment is
completed, printing of the job will continue automatically.
Action
None.
OS0855
After Print Quality
Adjustment: stop before
printing
This message specifies that when print quality adjustment is
completed, printing will not continue automatically.
Action
None.
OS0856
Print Quality Adjustment request has been canceled
Your PQA CANCEL command request has been processed and
print quality adjustment has been canceled.
Action
None.
6-6
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0860
Substituting color for color for this report
After you enter a SUBSTITUTE INK command, this message tells
you which primary color is being substituted for another primary
color in this report.
Note: The current settings are always displayed whenever a valid
SUBSTITUTE INK command is entered or following a successful
print quality adjustment. In addition, the current SUBSTITUTE
INK command settings are displayed at the time the output task
is loaded into memory. The exact wording of messages OS0860
through OS0875 depends upon the parameters you specify in
your SUBSTITUTE INK command.
Action
None.
OS0861
Substituting color for all colors for this report
After you enter a SUBSTITUTE INK command, this message tells
you the primary color which is being substituted for all non-black
primary colors in your report.
Action
None.
OS0862
Substituting color for all other inks for this report
After you enter a valid SUBSTITUTE INK command, this message
tells you the primary color which is being substituted for all
primary colors (including black) in your report.
Action
None.
OS0863
Substituting current dry ink for this report
The job requires a primary color that is not currently loaded. The
system, therefore, substitutes the ink currently loaded for the ink
specified in the report.
Action
None.
OS0864
All ink substitutions have been canceled
This message is displayed following your SUBSTITUTE INK
CANCEL ALL command.
Action
None.
OS0865
Color ink substitution has been canceled
This message is displayed following your SUBSTITUTE INK
CANCEL command
Action
None.
OS0870
Substituting color for all colors for all jobs
After you enter a SUBSTITUTE INK command, this message tells
you the primary color which is being substituted for all non-black
primary colors in all of the jobs you are running.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-7
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS0871
Substituting color for all colors for this job
After you enter a SUBSTITUTE INK command, this message tells
you the primary color which is being substituted for all non-black
primary colors specified in your job.
Action
None.
OS0872
Substituting color for color for all jobs
After you enter a SUBSTITUTE INK command, this message tells
you which primary color is being substituted for the specified
primary color(s) in all of your jobs.
Action
None.
OS0873
Substituting color for color for this job
After you enter a SUBSTITUTE INK command, this message tells
you which primary color is being substituted for the specified
color in your current job.
Action
None.
OS0874
Substituting color for all other inks for all jobs
After you enter a SUBSTITUTE INK command, this message tells
you the primary color which is being substituted for all other inks
(including black) in all of your jobs.
Action
None.
OS0875
Substituting color for all other inks for this job
After you enter a SUBSTITUTE INK command, this message tells
you the primary color which is being substituted for all other inks
(including black) in your job.
Action
None.
OS0900
Job xxxx aborted
One of the following commands was entered:
—ABORT job
—ABORT I
—ABORT O
The job indicated has been deleted from the print queue.
Action
None.
OS0950
Task aborted
The ABORT or @ABORT command was entered. The nonprint
task has been discontinued.
Action
None.
OS0990
Resetting the system
The RESET command was entered. All jobs in the print queue are
being deleted.
Action
None.
6-8
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS Level 1: Information
Informs you of system activies.
OS1000
Ready for commands hh:mm:ss
The system is ready to process commands entered. (The time of
day is displayed after the message.)
Action
Enter the command to initiate the desired process.
OS1002
Lockout mode active
The lockout diagnostic mode is currently active.
Action
None.
OS1003
Sample is not allowed. Printer is cycling down.
The system is in a cycling down state, so no sample requests can
be scheduled.
Action
None.
OS1004
Job abort in progress—Please wait
The system is busy cleaning up after an aborted job. The job is
not yet complete, so please wait until processing is finished.
Action
None.
OS1005
Sample not allowed while Sample Tray is selected
Intermixing sample sheets with the job output in the sample tray
would cause integrity errors. Sample is not allowed at this time.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-9
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1006
Printer is not available; Printer is being serviced
The printer is unable to respond to the entered command
because the Xerox service representative is performing diagnostic
tests.
The printer control console displays one of the following
messages for use of the service representative only:
BILLING METER A = xxxxxxxx
BILLING METER C = xxxxxxxx
BILLING METER E = xxxxxxxx
BILLING METER F = xxxxxxxx
BILLING METER H = xxxxxxxx
BILLING METER J = xxxxxxxx
CUSTOMIZED PROGRAMS--ENTER NUMBER: 00 OR PRESS P
AGAIN TO VIEW PROGRAM LIST
KEY OPERATOR PROGRAM--PRESS START TO RESET OR C TO
EXIT
PRESS P TO REPEAT LIST
PRESS C TO EXIT
PRESS START TO DISPLAY BILLING METER(S) OR PRESS C TO
EXIT
PRESS START TO INITIATE SERVICE TEST SEQUENCE
P10 DISPLAY BILLING METERS. PRESS START TO SELECT OR P
TO VIEW MORE
P72 SERVICE TEST SEQUENCE. PRESS START TO SELECT OR P
TO VIEW MORE
P73 SYSTEM RESET. PRESS START TO SELECT OR P TO VIEW
MORE
xx IS AN INVALID CUSTOMIZED PROGRAM NUMBER. PRESS P
TO TRY AGAIN
Action
None.
OS1007
Printer is busy
A command was entered while the printer was warming up or
adjusting print quality. The command will be ignored until the
printer completes activity.
Action
1.
Check the printer control console for explanatory messages.
2.
Wait until READY TO PRINT appears on the printer control
console and reenter the command.
OS1008
Printer is busy, command ignored
The PQA or SUBSTITUTE INK command you have entered is
rejected because the printer is busy processing a job.
Action
Retry the PQA or SUBSTITUTE INK command after the printer has
cycled down.
OS1010
Starting job xxxx
The system is initiating processing for the indicated job.
Action
None.
6-10
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1011
Starting diagnostic print job
The system diagnostic interface (SDI) task is involved.
Action
None.
OS1012
ALUN$ failed command ignored
The device substitution specified in the SUB DEV command has
failed. Check command and retry.
Action
None.
OS1013
Device offline, command ignored
The device substitution specified in the SUB DEV command has
failed. Check command and retry.
Action
None.
OS1014
Output cannot be switched--Selected Tray is full
The SELECT or SEPARATE command was entered while the printer
was printing. Output cannot be switched because the entered
stacker tray is full.
The printer control console displays:
OUTPUT TRAY CANNOT BE SWITCHED--SELECTED TRAY IS
FULL
Action
1.
Press the key or the Stop button on the printer to
halt printing.
2.
Unload the full stacker tray.
3.
Press the key to resume printing.
4.
Reenter the SELECT or SEPARATE command.
OS1015
ALDN$ failed, command ignored
The device substitution specified in the SUB DEV command has
failed. Check command and retry.
Action
None.
OS1016
NT01 or staple not supported
4635 does not support Staple. If Staple is specified in a JDE, JDL
or DJDE, then INPUT will ignore it.
Action
None.
OS1017
Physical device %0 substituted for logical device %1.
The device substitution specified in the SUB DEV command has
taken place.
Action
None.
OS1020
Job xxxx has completed input phase
All requested manipulation of data is complete and final imaged
pages are in the print file.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-11
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1030
Job xxxx has completed printing
The system has finished printing the indicated job.
Action
None.
OS1031
Diagnostic print job completed
This message indicates completion of a diagnostic print job.
Action
None.
OS1050
Rewind will be done at End-of-Job
When the job has completed processing, the tape will
automatically rewind.
Action
None.
OS1061
Initializing CSI
The printer interface board is being initialized to prepare for
operation.
Action
None.
OS1062
System mailbox initialized
This is a status message which appears whenever the system is
booted, advising you that the system mailbox feature is being
processed.
Action
None.
OS1070
Bar status changing to ON (End Of Report or Task Exit)
The command Bar Off n was entered disabling the barcode
reader for a specified number of sheets but the report ended
prior to reaching n count resulting in the barcode reader being
enabled.
Action
None.
OS1072
Bar OFF, n count satisfied, reader is now enabled
The command BAR OFF n was entered disabling the barcode
reader for a specified number of sheets. The count specified as
n was reached and the barcode reader has been enabled again.
Action
None.
OS1073
Data1 = nn, Data2 = nn, Data3 = nn, Data4 = nn
This message is for diagnostic purposes only.
Action
None.
OS1080
Start accounting report
The REPORT or ACCOUNT command was entered. The system
is compiling and printing, or writing to magnetic tape, a report of
system usage data.
Action
None.
6-12
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1085
Billing report starting
The REPORT BILLING command was entered. The system is
beginning a procedure to display the usage information required
for the Customer Billing Report (“meter read” information).
Action
None.
OS1086
Activity report starting
Processing of the Activity Report has begun.
Action
None.
OS1087
User report starting
Processing of the User Report has begun.
Action
None.
OS1090
End accounting report
The system accounting report has been printed or written to
magnetic tape.
Action
None.
OS1095
Billing report ending
The system has completed the display of information required for
customer billing.
Action
None.
OS1096
Activity report ending
Processing of the Activity Report has completed. No action.
Action
None.
OS1097
User report ending
Processing of the User Report has completed. No action.
Action
None.
OS1101
FCG working.
FCG tasks are in progress.
Action
None.
OS1102
Finishing Exerciser is reconnecting to the IOT.
After completing the test print job, FEX is reconnecting
communications with the printer and restoring the previous
finishing parameters information.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-13
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1103
FEX: Error, problem while restoring IOT Memory.
A serious error has occurred when FEX attempted to
communicate with the printer.
Action
Restart FEX.
OS1104
Failed to connect to the IOT. Exiting.
FEX could not establish communications with the printer,
because a job is printing.
Action
Restart FEX when the 4635 LPS is not actively printing a job.
OS1105
No valid machine serial number received. Task exiting
The printer serial number was not found when the system
attempted to produce a billing report.
Action
If authorized to do so, resysgen the system, entering the serial
number (located on a panel inside the printer) when instructions
on the display ask for it. (Refer to 4635 LPS System Generation
Guide, or contact your systems specialist.)
OS1106
Lowercase characters not valid in machine serial number
Lowercase characters are not valid in the machine serial number.
Action
1.
Verify the tray(s) or bin(s) in your command.
or
Select a different tray or bin.
2.
Retry the command.
OS1131
FEX: Problem communicating with the IOT. Exiting.
FEX has detected a problem communicating with the printer.
Action
Restart FEX.
OS1132
--- NVM Finishing locations ---
This message lists the values that are currently in the printer‘s
non-volatile memory.
Action
Save (write down) these values so that you can restore them
should an FEX communications problem lose these values from
the printer‘s non-volatile memory.
OS1133
FEX: Warning, number of pages is greater than 23.
This message advises you that you have selected too many pages
for the FEX test print job.
Action
1.
Select fewer pages for the test case job.
2.
Retry running FEX.
Note: This may be an issue only with certain finishing devices
which require readjustments for page sets of more than 23
pages. Consult your finishing device documentation for
additional information.
6-14
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1134
Checking for existence of x.x on system
FEX is looking for the requested .FRM directory in the system‘s
memory. If FEX finds the requested form name, it will show
‘FOUND’ on the display.
Action
None.
OS1135
FEX: Error, Form: x.x does not exist. Exiting.
FEX cannot find the requested .FRM directory in the system.
Action
Verify the form directory (file-name) and retry the command.
OS1136
Sheet rotation: ‘0’ = None or ‘1’ = Rotate sheet:
This is one of a series of FEX questions about the test print job,
which also includes messages OS2922, OS2923, OS2924, and
OS2008.
Action
Enter 0.
OS1137
Rotation will be set to x.
This message verifies that you have selected either rotation (‘1’)
or non-rotation (‘0’) of sheets for your FEX test print job.
Action
None.
OS1150
Job queue full
Print queue cannot hold any more data.
Action
Print or delete jobs in queue before more jobs are sent.
OS1155
Request rejected, diagnostic job already in progress
A diagnostic print job is already being processed; additional
requests are rejected.
Action
None.
OS1160
No pages waiting to be drained
The DRAIN command was entered. No complete pages remain
in the print file or memory.
Action
None.
OS1170
Invalid command while offline
An online only command was entered while the system is offline.
Action
Place the system online to perform the desired function. (Refer
to the online chapter in your 4635 LPS Operator Guide.)
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-15
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1175
Command not allowed while **** is active
The command entered cannot be processed while the indicated
task is in progress.
Action
1.
Exit indicated task. (Refer to appropriate section of your
4635 LPS Operations Reference for instructions.)
2.
Reenter the command.
OS1180
Invalid response
Response to a prompt was incorrectly entered.
Action
Reenter response, ensuring accuracy and the correct number of
characters.
OS1190
Invalid parameter, command ignored.
An undefined bin is specified or the sheet count for the bin is
not within the allowable range.
Action
Verify the bin and reenter the command
or
Change the BLIMIT command to allow your number of sheets.
(The allowable range is 100-2500 sheets.)
or
An undefined tray is specified in the command. Verify the tray
number and reenter the command. (The allowable trays are 1-6.)
OS1195
Undefined ink: color
The ink you specified (represented by the word color in the
message shown) is incorrect.
Action
1.
Check to make sure that the ink name is entered correctly.
2.
If the message reappears, consult your systems specialist.
OS1200
Command not allowed while HIP or SDI active
The system is unable to respond to the entered command while
the printer is in communication with the host interface processor.
Action
1.
Terminate connection with HIP. (Refer to the HIP chapter in
your 4635 LPS Operator Guide.)
2.
Reenter the desired command.
OS1215
Input stopped after orderly shutdown
A software failure has caused a system rollover. Data being input
has stopped processing while the system attempts to reestablish
the correct state at the time of failure in an effort to recover all
data.
Action
Follow directions appearing at the system controller display to
initiate automatic job recovery and abort the analysis dump.
(Refer to the offline chapter in your 4635 LPS Operator Guide.)
6-16
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1225
Automatic recovery initiated
Automatic job recovery has been initiated at the system
controller display after a system rollover due to software failure.
Action
Follow directions appearing at the system controller display to
complete the recovery process.
OS1230
Separate not permitted with destination configuration
This is a response to SEPARATE ON or SEPARATE OFF when a
two-tray stacker is not present.
Action
None.
OS1235
CLP Commands not allowed while printing
A CLP command was entered. CLP commands may not be used
while the printer is active.
Action
None.
OS1240
Status command inoperative
The key was pressed or the JOBS command
was entered. The system is unable to display status because a
file was not created at sysgen due to insufficient disk space.
Action
1.
Delete files to create more space.
2.
Compress disk.
3.
Enter the SFS CREATE command to create a status file. (Refer
to your 4635 LPS Operations Reference chapter on system
and report accounting, including status file information, for
details.)
OS1245
STAFIL.SYS Initialization failure status inoperative
The SFS CREATE command was entered. The system is unable to
process the command because the file was not created at sysgen
due to insufficient disk space.
Action
1.
Delete some files to create more space.
2.
Compress disk.
3.
Enter the SFS CREATE command to create a status file. (Refer
to your 4635 LPS Operations Reference chapter on tracking
system activity for additional information.)
OS1250
Accounting enabled
A disabled accounting function has been reinstated.
Action
None.
OS1255
Accounting disabled
The accounting function is restricted. The system will not
process the ACCOUNT or REPORT command that has been
entered.
Action
Obtain the correct password and log on at the correct level.
(Refer to your 4635 LPS Operations Reference chapter on setting
LPS parameters for additional information.)
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-17
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1261
Paper size out of range
The paper size specified in the JSL is not supported by the IOT.
Action
Contact your systems specialist.
OS1262
Sysgen paper size out of range
If a paper size statement is not included in the JDL, the system
will use the values specified at SYSGEN. This message indicates
that the SYSGEN value is not supported by the IOT.
Action
Perform a MINI SYSGEN and correct the default paper size.
OS1263
Form paper size out of range: xxxxxx.xxx
Paper size for form specified in the JSL is not supported by the
IOT.
Action
Contact your systems specialist.
OS1264
Barcode sequence mismatch
The IOT detected a sequence number other than the one
expected.
Action
Check the job, correct the reason for the mismatch and rerun.
OS1265
Printer status request already in progress
A previous request for printer status is still being processed.
Action
None.
OS1266
A Barcode was specified, none found
The IOT did not detect a barcode where one was expected.
Action
Check Read Head alignment, bar code programming or continue
job in BAR OFF mode.
OS1267
ESS didn't confirm duplex hint
A sheet abort request was sent to the ESS from the IOT because
the ESS didnot confirm a hint for the second side of a sheet
already committed to the paper path.
Action
None.
OS1268
Bar Align: sheet delivered. Seq1 = nn, Seq2 = nn
Sheets with sequence numbers have been read and delivered
with the printer operating in the bar align mode. Seq1 - front
side, Seq2 - back side.
Action
None.
OS1269
Bar Align: sheet delivered
Sheets were delivered but no sequence numbers were read with
the printer operating in the bar align mode.
Action
None.
6-18
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1270
Command file aborted
The @ABORT command was entered. The system has
abandoned processing of the initiated command file.
Action
None.
OS1271
Cannot nest command files. Check and retry.
The command file entered is formatted incorrectly. It appears to
be contained (nested) within another command file
Action
1.
Correct your command file format. (Refer to your 4635 LPS
Operations Reference chapter on creating and using
command files for additional information.)
2.
Retry your command file request.
OS1272
Command file delaying
The .DELAY n command was entered. Command file processing
is being suspended for a specified period of time. (n = number
of seconds.)
Action
None.
OS1273
Command file resumed
Following an interruption, command file operations have started
again.
Action
None.
OS1275
Command file suspended
The .PAUSE command was entered. Command file processing is
suspended for an unspecified period of time.
or
The .WAIT command was entered. Command file processing is
suspended until the current print job is completed.
Action
None.
OS1276
Command file not suspended.
This message advises you that command file operations have not
stopped being processed.
Action
None.
OS1278
Command file terminated
The .EXIT command was entered. Command file processing is
ended.
Action
None.
OS1279
Command file error - label not found
An incorrect prefix was entered for the command file.
Action
Reenter the statement correctly.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-19
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1280-OS1282
Message file error messages
The message file containing the message that should be
displayed for the indicated task does not exist on the system
disk.
Note: Messages OS1280 and OS1282 should not appear. If one
of these messages should occur:
Action
1.
Document circumstances of the message appearance.
2.
Record any additional messages displayed in conjunction with
it.
3.
Contact your systems specialist or Xerox Customer Service
with the above information.
OS1280
Message file is not defined. Requesting ******;
message file: **;
OS1282
Message file does not exist. Requesting task: ******;
Message file: **;
OS1283
Unexpected Barcode encountered
The IOT read a barcode when there should not have been one.
Action
Abort the job and correct the job programming or continue the
job in the BAR OFF mode.
OS1285-OS1287
Message file error messages
The message file containing the message that should be
displayed for the indicated task does not exist on the system
disk.
Note: Messages OS1285 and OS1287 should not appear. If one
of these messages should occur:
Action
1.
Document circumstances of the message appearance.
2.
Record any additional messages displayed in conjunction with
it.
3.
Contact your systems specialist or Xerox Customer Service
with the above information.
OS1285
Message does not exist. Requesting task: ******;
OS1287
Should not display this message. Requesting task: ******;
OS1290
Cluster file full
The file containing the list of clusters is full.
Action
Delete one or more clusters, and retry.
Note: The file can only contain 152 clusters.
OS1291
Cluster name not defined.
or
Cluster ***
Cluster has no current trays ***
You have entered a PQA command or a job start command
containing an undefined cluster or one with no current trays.
Action
1.
Verify the clusters to be used for your job.
2.
Reenter the PQA command.
6-20
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1292
Command ignored.
Main or Aux Cluster not selected
The FEED command can only cause the system to toggle
between the MAIN and AUX clusters. Since neither MAIN nor
AUX had been selected, this command has been ignored.
Action
Enter the name of the specific cluster you wish to select. (Refer
to your 4635 LPS Operations Reference chapter on setting up
print jobs for additional information.)
OS1293
Feed Main/Aux not in effect, unable to toggle
The system is unable to switch (toggle) between the main and
auxilliary feeder trays.
Action
Check your cluster configuration and enter a new command that
will allow toggling. (Refer to the chapter on feeder trays in your
4635 LPS Operations Reference.)
OS1294
Invalid paper tray selected. Command ignored
A command was entered that refers to a (feeder) tray not in the
printer configuration, e.g., (feeder) trays 3 and 4 can only be
selected when your printer has a high-capacity feeder.
Action
Select a (feeder) tray that is part of your printer‘s configuration.
(Refer to the chapter on feeder trays in your 4635 LPS Operator
Guide.)
OS1295
Destination trays not configured for this command
A command was entered that is invalid for the printer‘s stacker
tray configuration.
Action
Reenter the command, using a stacker bin that your system has.
(Refer to the output tray or bin chapter in your 4635 LPS
Operator Guide.)
OS1296
There is no stockset specified at this time
The CLUSTER SET or CLUSTER SET N/R command was entered
but the collection of stocks to be used in the print job has not
been specified. (Refer to your 4635 LPS PDL/DJDE Reference.)
Action
Reprogram job to contain a stockset or wait until such a job is
running before entering this command.
OS1297
There are no current trays in any cluster
The CLUSTER command was entered but no clusters have been
defined.
Action
Define the desired cluster. (Refer to your 4635 LPS Operations
Reference chapter on setting up print jobs for additional
information.)
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-21
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1298
Specified paper tray not present
A command was entered that refers to a feeder tray not in the
printer configuration.
Action
Reenter the command, using a feeder tray that your system has.
(Refer to the chapter on feeder trays in your 4635 LPS Operator
Guide.)
OS1300
Number of active forms is nn
The maximum number of forms per print job the system will
attempt to keep in forms memory is (number 0-64). This
message appears at installation when forms memory space is
allocated.
Action
None.
OS1310
Number of active fonts is nn
The maximum number of fonts per print job the system will
attempt to keep in memory is (number 0-128). This message
appears at installation when font memory space is allocated.
Action
None.
OS1320
Number of active graphics is nn
The maximum number of graphics per print job the system will
attempt to keep in GHO memory is (number 16-128). This
message appears at installation when graphics memory space is
allocated.
Action
None.
OS1321
Print darkness level is nn.
After entering the DARKNESS command with a level parameter,
this message tells you that the value you have entered is
accepted. If you enter the DARKNESS command with no
parameters, the message tells you the current level setting.
Action
None.
OS1322
Lead edge screen setting is nn
This message confirms that your EDGE (lead edge screen)
command parameters have been accepted or provides you with
the current settings if you have not entered new parameters.
Action
None.
OS1323
Energy saver timeout is nn minutes
After entering the ENERGY command with a timeout parameter,
this message tells you that the value you have entered is
accepted. If you enter the ENERGY command with no
parameters, the message tells you the number of minutes
currently set.
Action
None.
6-22
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1324
Energy Saver mode is disabled
The energy saver has been turned off.
Action
None.
OS1325
IOT Attention steady light is xxx, flashing light is xxx
After entering the ATTENTION LIGHT command, this message
tells you whether the attention light(s) on your system‘s printer is
enabled or disabled, steady or flashing. If you enter the
ATTENTION LIGHT command with no new parameters, the
message provides the current settings.
Action
None.
OS1326
Already in lockout mode
During service activities, the LOCKOUT mode has already been
initiated.
Action
None.
OS1329
BINFULL criteria: n% ream threshold, n% boundary
After entering the BINFULL command with threshold and
boundary parameters, this message tells you that the values you
have entered are accepted. If you enter the BINFULL command
with no parameters, the message tells you the current settings.
Action
None.
OS1330
XPS Accounting reset
XPS deletes all accounting files and recreates and initializes the
accounting recovery file.
Action
Enter XPS command.
OS1331
XPS Accounting aborted
XPS has stopped accumulating accounting data because there is a
disk access error.
Action
None.
OS1332
XPS Accounting resumed
XPS resumes the accumulation of accounting data because the
problem causing the abort is resolved.
Action
None.
OS1333
XPS Accounting stopped: maximum file count exceeded
XPS has stopped accumulating accounting data because the
number of files has reached the maximum specified by ACFILES
in HIP.LIB.
Action
None.
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
6-23
OSS (OPERATING SYSTEM SOFTWARE) MESSAGES
OS1334
Printer alarm is n, level = n
After entering the ATTENTION ALARM command, this message
tells you whether the alarm is enabled or disabled. If you enter
the ATTENTION ALARM ENABLE command, the message tells you
that the value you requested is accepted or provides the current
setting if you have not included the parameter with the
command.
Action
None.
OS1335
XPS Accounting stopped: no disk space for files
XPS is unable to accumulate accounting data because there is no
disk space for files.
Action
None.
OS1336
XPS Accounting enabled
XPS received a request from the server to enable accounting.
Action
None.
OS1337
XPS Accounting disabled
XPS recieved a request from the server to disable accounting or
HIP was unloaded by entering the HIP END command.
Action
None.
OS1342
Currently not in Lockout Mode
This message informs you that the LOCKOUT mode has not
been initiated.
Action
None.
OS1380
Alignment is nn Scan Lines and nn Dots
Printed data will appear at the indicated number (76-260) of lines
from the top and bottom edges of paper, and the indicated
number (0-795) of dots from the right and left edges of paper.
Action
None.
OS1381
Diagnostic alignment is x Scan lines and y Dots
For Xerox service personnel, this message provides alignment
information.
Action
None.
OS1390
Invalid Scan or Dot value. Retry Align
The alignment number entered for dots or lines is not within the
permitted range.
Action
Reenter the ALIGN command with value(s) within the range.
(Refer to the problem solving chapter in your 4635 LPS Operator
Guide.)
6-24
XEROX 4635 LASER PRINTING SYSTEM MESSAGE GUIDE
