Alcatel-Lucent Data Multiplexer Explore 1665 Installation Manual

| Release 10.0 Installation Manual 365-372-327R10.0 Issue 1 | January 2013

The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein. Copyright © 2013 Alcatel-Lucent. All Rights Reserved. Conformance statements Federal Communications Commission (FCC) Part 15 Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protections against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s expense. Security statement In rare instances, unauthorized individuals make connections to the telecommunications network through the use of remote access features. In such an event, applicable tariffs require that the customer pay all network charges for traffic. Alcatel-Lucent cannot be responsible for such charges and will not make any allowance or give any credit for charges that result from unauthorized access. Limited warranty Alcatel-Lucent provides a limited warranty for this product. For more information, consult your local Alcatel-Lucent customer support team.

Alcatel-Lucent 1665 DMXtend R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Contents About this document Purpose ...................................................................................................................................................... xiii Reason for reissue ..................................................................................................................................... xiii Intended audience ...................................................................................................................................... xiii \How to use this document .........................................................................................................................xiv Safety information .................................................................................................................................... xvii Conventions used ...................................................................................................................................... xvii Technical support .................................................................................................................................... xviii How to order .............................................................................................................................................. xix How to comment ....................................................................................................................................... xix Packaging collection and recovery requirements ...................................................................................... xix Material content compliance ..................................................................................................................... xix 1 Safety Laser safety ............................................................................................................................................... 1-1 Electrostatic discharge ESD considerations .............................................................................................. 1-3 Laser product classification ....................................................................................................................... 1-9 Alcatel-Lucent 1665 DMXtend optical specifications ............................................................................ 1-11 Part I: Physical and power installation 2 Physical installation Planning ..................................................................................................................................................... 2-1 Inspection .................................................................................................................................................. 2-5 Alcatel-Lucent 1665 DMXtend center divider .......................................................................................... 2-5 Alcatel-Lucent 1665 DMXtend shelf installation ..................................................................................... 2-8 Power cable installation ........................................................................................................................... 2-13 Final operations ....................................................................................................................................... 2-17 3 Cable and fiber installation Planning ..................................................................................................................................................... 3-2 Connector references ................................................................................................................................. 3-4

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Contents Inspection .................................................................................................................................................. 3-5 DS1/E1 cable installation .......................................................................................................................... 3-6 DS3/EC-1 cable installation .................................................................................................................... 3-13 10/100BASE-T Ethernet cable installation ............................................................................................. 3-36 Ethernet cabling to SFP modules on circuit pack faceplates .................................................................. 3-40 IAO LAN and TCP/IP cable installation ................................................................................................. 3-41 Modem cable installation ........................................................................................................................ 3-44 Sync cable installation ............................................................................................................................ 3-46 Office alarm cable installation ................................................................................................................ 3-50 Miscellaneous (environmental) discrete telemetry cable installation ..................................................... 3-54 OC-3/OC-12/OC-48/OC-192 main optical fiber cable installation ........................................................ 3-58 OC-3/OC-12/OC-48 low-speed optical fiber cable installation .............................................................. 3-61 100/1000BASE-X optical fiber cable installation ................................................................................... 3-62 CIT (RS-232) cable installation .............................................................................................................. 3-64 Final operations ....................................................................................................................................... 3-66 4 Circuit pack installation Description ................................................................................................................................................ 4-1 Powering ................................................................................................................................................... 4-2 Circuit pack compatibility ......................................................................................................................... 4-6 Initial circuit pack installation ................................................................................................................... 4-9 Part II: Stand-alone installation tests 5 Stand-alone node setup Software installation ................................................................................................................................. 5-2 Circuit pack installation ............................................................................................................................ 5-3 Use of WaveStar® CIT software ................................................................................................................ 5-6 Circuit pack program version verification .............................................................................................. 5-12 Alcatel-Lucent 1665 DMXtend shelf initialization ................................................................................ 5-13 6 Stand-alone installation testing LBO software settings ............................................................................................................................... 6-4 Clearing alarms ......................................................................................................................................... 6-7 Local equipment and cross-connect tests .................................................................................................. 6-8 DS1/E1 testing .......................................................................................................................................... 6-9

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ ............................................................................................................................................................................................................................................................ Contents DS3/EC1 testing ...................................................................................................................................... 6-15 LNW74 and LNW87 testing ................................................................................................................... 6-22 OC-3 low-speed testing ........................................................................................................................... 6-24 OC-12 low-speed testing ......................................................................................................................... 6-29 OC-48 low-speed testing ......................................................................................................................... 6-32 OC-192 low-speed testing ....................................................................................................................... 6-36 LED test ................................................................................................................................................... 6-40 Office alarm test ...................................................................................................................................... 6-41 Automatic protection switching and alarm test ....................................................................................... 6-45 Manual switching tests ............................................................................................................................ 6-49 External timing verification ..................................................................................................................... 6-52 Miscellaneous (environmental) discrete telemetry test ........................................................................... 6-55 Modem connection test ........................................................................................................................... 6-59 Final operations ....................................................................................................................................... 6-61 Part III: Network turn-up and testing 7 Connecting adjacent network elements Fiber installation ........................................................................................................................................ 7-3 Optical transmission test (OC-192, OC-48, OC-12, OC-3) .................................................................... 7-10 Automatic protection switching test ........................................................................................................ 7-11 Manual switching tests ............................................................................................................................ 7-13 Final operations ....................................................................................................................................... 7-15 8 WDMX setup and testing: integration procedures Turn-up and test the LNW785 8-channel OMD ....................................................................................... 8-4 Turn up and test the LNW705 muxponder ................................................................................................ 8-6 Integrating the LNW705 into the LNW785 .............................................................................................. 8-9 Removing provisioning and equipage from the LNW705 and LNW785 ............................................... 8-11 Connecting the ring (Mains) to the WDMX ........................................................................................... 8-14 Removing provisioning and equipage from the LNW785 ...................................................................... 8-16 Part IV: Miscellaneous detailed installation procedure and reference material A Fiber cleaning Equipment requirements and recommendations ...................................................................................... A-2

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Contents Safety instructions .....................................................................................................................................A-3 Cleaning/inspecting optical connectors ....................................................................................................A-3 Cleaning pluggable optics module ............................................................................................................A-9 B Pluggable Transmission Module (PTM) installation PTM modules ............................................................................................................................................B-2 Install pluggable modules .........................................................................................................................B-8 C Installing fiber connectors and LBOs LBOs .........................................................................................................................................................C-2 Attenuation for circuit packs and PTMs ...................................................................................................C-4 Fiber connections ......................................................................................................................................C-7 D Backplane pin replacement Pin and connector background ..................................................................................................................D-2 Repair kits and tools ..................................................................................................................................D-3 Simple repair methods ..............................................................................................................................D-4 Replacement methods ...............................................................................................................................D-5 E Fiber labeling Fiber description .......................................................................................................................................E-1 Fiber labels ................................................................................................................................................E-3 GL Glossary GL Terms and definitions

Alcatel-Lucent 1665 DMXtend R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ List of tables 1 Alcatel-Lucent 1665 DMXtend documentation set ................................................................1-xviii 1 Safety 1-1 Laser classes ............................................................................................................................... 1-10 1-2 Alcatel-Lucent 1665 DMXtend optical circuit pack laser safety specifications ........................ 1-11 1-3 Alcatel-Lucent 1665 DMXtend optical PTM laser safety specifications .................................. 1-12 1-4 Dispersion-limited receiver sensitivity for OC-192 DWDM PTMs .......................................... 1-21 I-1 Computer requirements .................................................................................................................I-5 I-2 Installation checklist ......................................................................................................................I-6 2 Physical installation 2-1 Cable requirements and options ................................................................................................... 2-4 2-2 Power cable assemblies .............................................................................................................. 2-16 2-3 Power connections ...................................................................................................................... 2-16 3 Cable and fiber installation 3-1 Cable requirements and options ................................................................................................... 3-3 3-2 DS1/E1 cable assemblies ............................................................................................................. 3-9 3-3 DS1 transmission connections ................................................................................................... 3-11 3-4 DS3/EC-1 cable assemblies ....................................................................................................... 3-17 3-5 Twenty-four cable DS3/EC-1 transmission connections ........................................................... 3-24 3-6 Twelve cable DS3/EC-1 transmission connections .................................................................... 3-28 3-7 DS1 and DS3 hybrid cable assemblies ....................................................................................... 3-33 3-8 DS1 and DS3 hybrid cable DS3 transmission connections ....................................................... 3-35 3-9 DS1 and DS3 hybrid cable DS1 transmission connections ....................................................... 3-35 3-10 10/100Base-T Ethernet cable assemblies ................................................................................... 3-38 3-11 10/100BaseT Ethernet connections ............................................................................................ 3-39 3-12 GbE ethernet cables .................................................................................................................... 3-40 3-13 LAN 10BaseT cable assemblies ................................................................................................. 3-42 3-14 LAN 10Base-T cross-over cable connections ............................................................................ 3-44 3-15 LAN 10Base-T straight-through cable connections ................................................................... 3-44 3-16 Modem cable assemblies ............................................................................................................ 3-45

Alcatel-Lucent 1665 DMXtend R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ List of tables 3-17 Modem cable connections .......................................................................................................... 3-46 3-18 Synchronization cable assemblies (SYNC1 and SYNC2) ......................................................... 3-49 3-19 Synchronization cable (DS1 timing reference) connections ...................................................... 3-50 3-20 Office alarm cable assemblies .................................................................................................... 3-53 3-21 Alarm office connections ........................................................................................................... 3-53 3-22 Miscellaneous discrete cable assemblies ................................................................................... 3-57 3-23 Miscellaneous (environmental) discrete telemetry connections ................................................ 3-57 3-24 CIT Cable Assembly .................................................................................................................. 3-64 3-25 Standard CIT cable connection .................................................................................................. 3-65 3-26 RJ-45 to DB-9 connector connections ....................................................................................... 3-65 4 Circuit pack installation 4-1 Alcatel-Lucent 1665 DMXtend shelf power supply requirements .............................................. 4-2 4-2 R10.0circuit pack slot compatibility ............................................................................................ 4-6 4-3 OC-3 mains with 6 STS-1s of vt switch fabric ............................................................................ 4-8 4-4 OC-12 mains with 12 STS-1s of vt switch fabric ........................................................................ 4-8 4-5 OC-48 Mains with 48 STS-1s of vt switch fabric ........................................................................ 4-9 4-6 OC-192 circuit packs with 192 STS-1s of vt switch fabric (VLF) .............................................. 4-9 4-7 OC3/12/48 circuit packs with 192 STS-1s of vt switch fabric (VLF) ......................................... 4-9 4-8 Alcatel-Lucent 1665 DMXtend shelf ........................................................................................... 4-9 5 Stand-alone node setup 6 Stand-alone installation testing 6-1 Office alarm connections ........................................................................................................... 6-42 6-2 Miscellaneous (environmental) discrete telemetry connections ................................................ 6-58 7 Connecting adjacent network elements 7-1 Attenuation table .......................................................................................................................... 7-6 8 WDMX setup and testing: integration procedures 8-1 Channel/port assignments .......................................................................................................... 8-13 8-2 XM10G/8 PTM port guidelines ................................................................................................. 8-14 8-3 Channel/port assignments ......................................................................................................... 8-19 8-4 Attenuation Table ....................................................................................................................... 8-19 A Fiber cleaning A-1 Required and recommended equipment and materials ................................................................A-2

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ ............................................................................................................................................................................................................................................................ List of tables B Pluggable Transmission Module (PTM) installation B-1 Alcatel-Lucent approved PTMs ...................................................................................................B-2 C Installing fiber connectors and LBOs C-1 Circuit pack attenuation table .......................................................................................................C-4 C-2 PTM attenuation table ..................................................................................................................C-5 C-3 LBOs based on attenuation ..........................................................................................................C-7 D Backplane pin replacement D-1 Backplane locations of METRAL™ pins ................................................................................... D-3 D-2 Metral™ pins .............................................................................................................................. D-3 E Fiber labeling

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ List of tables

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ List of figures 1 Safety 1-1 Static control wrist strap ............................................................................................................... 1-5 2 Physical installation 2-1 Shelf mount rear cover kit 849001367 ......................................................................................... 2-3 2-2 Bay mount rear cover kit 849001060 ........................................................................................... 2-4 2-3 Center divider ............................................................................................................................... 2-6 2-4 Center divider with circuit packs installed. .................................................................................. 2-7 2-5 Alcatel-Lucent 1665 DMXtend mounting bracket positions - 23-Inch/19-Inch frame ............. 2-10 2-6 Fiber duct mounting ................................................................................................................... 2-11 2-7 Safety ground screw. .................................................................................................................. 2-12 2-8 Fiber spools ................................................................................................................................ 2-13 2-9 Power connection ....................................................................................................................... 2-14 3 Cable and fiber installation 3-1 Connector types and pinouts ........................................................................................................ 3-5 3-2 DS1/E1 cable connectors ............................................................................................................. 3-7 3-3 DS1/E1 cable routing to the right ................................................................................................. 3-8 3-4 DS1/E1 cable routing to the left ................................................................................................... 3-8 3-5 DS3/EC-1 cable connections ..................................................................................................... 3-15 3-6 DS3/EC-1 cable routing to the right .......................................................................................... 3-15 3-7 DS3/EC-1 cable routing to the left ............................................................................................ 3-16 3-8 DS1 and DS3 hybrid cable connections ..................................................................................... 3-31 3-9 DS1 and DS3 hybrid cable routing ........................................................................................... 3-31 3-10 10/100BASE-T/TX cable connections ....................................................................................... 3-37 3-11 10/100BASE-T cable routing ..................................................................................................... 3-37 3-12 IAO LAN/TCP-IP cable connection to rear of Alcatel-Lucent 1665 DMXtend ...................... 3-42 3-13 Modem cable connection .......................................................................................................... 3-45 3-14 Sync cable connections .............................................................................................................. 3-47 3-15 Office alarm cable connections .................................................................................................. 3-51 3-16 Office alarm cable routing .......................................................................................................... 3-51

Alcatel-Lucent 1665 DMXtend R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ List of figures 3-17 Miscellaneous discrete cable connection .................................................................................. 3-55 3-18 Miscellaneous discrete cable routing ........................................................................................ 3-55 3-19 Optical fiber routing .................................................................................................................. 3-60 4 Circuit pack installation 4-1 Power connections on Alcatel-Lucent 1665 DMXtend backplane .............................................. 4-4 5 Stand-alone node setup 6 Stand-alone installation testing 6-1 Alcatel-Lucent 1665 DMXtend shelf backplane ....................................................................... 6-54 6-2 Miscellaneous (environmental) discrete functions ................................................................... 6-57 7 Connecting adjacent network elements 8 WDMX setup and testing: integration procedures A Fiber cleaning A-1 Cleaning the ferrule endface ........................................................................................................A-4 A-2 CLETOP cleaner ..........................................................................................................................A-5 A-3 Acceptability criteria for fiber cleaning .....................................................................................A-7 B Pluggable Transmission Module (PTM) installation B-1 Pluggable optics module ..............................................................................................................B-9 B-2 Module types ..............................................................................................................................B-10 B-3 Latch type 3 ...............................................................................................................................B-12 B-4 Latch type 4 ................................................................................................................................B-12 B-5 Electrical PTM routing ..............................................................................................................B-15 C Installing fiber connectors and LBOs C-1 LC-type connector ports on circuit pack ......................................................................................C-2 C-2 LC-type LBO ...............................................................................................................................C-3 C-3 LC-type LBO inserted into LC-type connector port ...................................................................C-3 C-4 Removing LC-type LBO from LC-type connector port ..............................................................C-4 C-5 LC-type fiber connector ...............................................................................................................C-8 C-6 LC-type fiber connection .............................................................................................................C-8 D Backplane pin replacement E Fiber labeling

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ About this document Purpose This document provides the information and procedures necessary to install, self-test and turn up Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend). Reason for reissue This document is being reissued to include information about new features and hardware associated with R10.0 including: • Support for new circuit pack (LNW910): 1x10GE and 10xFE/GE with VLF interworking • In-service LNW31 OC-48 to LNW603 OC-192 upgrade • Report alarms from sub-shelves via SNMP (single TID applications) • Revertive option on UPSR per STS-1 cross-connect • Remote test access over protected UPSR tributaries when the mains are equipped with VLF packs • VT1.5 added to integrated test access capability Intended audience This installation manual is intended to provide individuals and customers the information and procedures necessary to install, self-test and turn up the Alcatel-Lucent 1665 DMXtend system.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ About this document This manual is not a service or operations manual. For any activities involving circuit turn- up, regular maintenance, or trouble analysis, refer to: • Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) User Operations Guide, 365-372-325 • Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Maintenance and Trouble Clearing Guide, 365-372-326 \How to use this document This manual is divided into the following sections with a brief description of the contents of each major part/chapter/appendix: About this document This chapter describes the purpose, intended audience, reason for reissue, and organization of this document. This section references related documentation and explains how to order, make comments or recommend changes to this document. Chapter 1, “Safety” This chapter provides laser safety information and precautions. Part I: “Physical and power installation” Part I covers Chapters 2, 3, and 4. These sections covers the physical mounting of the Alcatel-Lucent 1665 DMXtend shelf using the Horizontal Bay Mount. This section includes the running and connecting of power cables, interconnecting cables, alarm cables, and as required, external timing, communication cables, and covers initial circuit pack installation (not seated). This section also provides the recommended checklist Table I-2 “Installation checklist” to follow when installing a Alcatel-Lucent 1665 DMXtend system. Use of the installation checklist is required to ensure a quality installation. All completed tasks should be checked off and those not completed should be duly noted as to the reason why. This checklist should be turned in as part of your job complete paperwork. Chapter 2, “Physical installation” This chapter provides equipment installation instructions for the Alcatel-Lucent 1665 DMXtend shelf using the horizontal bay mount configuration. The Alcatel-Lucent 1665 DMXtend shelves with the removable center divider can support either half width or full width cards in the Main function slots. Chapter 3, “Cable and fiber installation” This chapter provides cabling instructions for the Alcatel-Lucent 1665 DMXtend shelf using the horizontal bay mount configuration.

R10.0 365-372-327R10.0 Issue 1 January 2013 xv ............................................................................................................................................................................................................................................................ About this document Chapter 4, “Circuit pack installation” This chapter provides information for verifying that the shelf is being supplied with the proper power and provides instructions for circuit pack installation. Part II: “Stand-alone installation tests” Part II covers Chapters 5 and 6. These sections cover the initial Graphical User Interface (GUI) or Craft Interface Terminal (CIT) software installation and turn-up testing on a new Alcatel-Lucent 1665 DMXtend shelf. It is intended to verify correct electrical DS1/DS3/FE cable wiring to the DSX panel or punch down block as well SONET fiber routing to the LGX panel from the faceplates of installed packs. This section also the recommended checklist “Installation checklist” to follow when installing a Alcatel- Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend) system. Use of the installation checklist is required to ensure a quality installation. All completed tasks should be checked off and those not completed should be duly noted as to the reason why. This checklist should be turned in as part of your job complete paperwork. Chapter 5, “Stand-alone node setup” This chapter provides procedures for initial Graphical User Interface (GUI) or Craft Interface Terminal (CIT) software installation and circuit packs provided via work order. Also, the use of the Graphical User Interface (GUI) or Craft Interface Terminal (CIT). Chapter 6, “Stand-alone installation testing” This chapter is to verify proper transmission cabling installation and R10.0 functionality as well as the associated functionality of the Alcatel-Lucent 1665 DMXtend shelf. Part III: “Network turn-up and testing” Part III covers fiber connections between nodes in a ring. It is not intended to replace acceptance test procedures. This section also provides the recommended checklist “Installation checklist” to follow when installing a Alcatel-Lucent 1665 DMXtend system. Use of the installation checklist is required to ensure a quality installation. All completed tasks should be checked off and those not completed should be duly noted as to the reason why. This checklist should be turned in as part of your job complete paperwork. Chapter 7, “Connecting adjacent network elements” This chapter is used to make fiber connections between nodes in a ring. It is not intended to replace acceptance test procedures.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ About this document Chapter 8, “WDMX setup and testing: integration procedures” This chapter is used to verify WDMX connectivity between Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend) nodes. The chapter includes the LNW785 8 channel Optical Multiplexer Demultiplexer (OMD) circuit pack. It is not intended to replace acceptance test procedures. Part IV: “Miscellaneous detailed installation procedure and reference material” Part IV provides supplementary information that is useful when installing the Alcatel- Lucent 1665 DMXtend system and using this Installation Manual. Appendix A, “Fiber cleaning” This appendix describes the Alcatel-Lucent recommended method for the cleaning and inspection of optical connectors using specific tools and materials that have been proven to be effective in the assembly and testing of optical transmission equipment. Appendix B, “Pluggable Transmission Module (PTM) installation” This appendix provides examples of PTM installation. Appendix C, “Installing fiber connectors and LBOs” This appendix provides procedures for installing and removing the types of Line Build Out units (LBOs) and fiber connectors onto input and output ports found on the Alcatel- Lucent 1665 DMXtend circuit packs. Appendix D, “Backplane pin replacement” This appendix provides information and the procedures used when a pin or blade on the Alcatel-Lucent 1665 DMXtend backplane has been bent or broken. Appendix E, “Fiber labeling” This appendix describes the labeling of the fiber. Glossary The Glossary provides definitions for telecommunication acronyms and terms. Index The Index supplies users with specific subjects and corresponding page numbers to find necessary information.

R10.0 365-372-327R10.0 Issue 1 January 2013 xvii ............................................................................................................................................................................................................................................................ About this document Safety information This information product contains hazard statements for your safety. Hazard statements are given at points where safety consequences to personnel, equipment, and operation may exist. Failure to follow these statements may result in serious consequences. Safety precautions Adhere to the following safety precautions: • Electrostatic discharge (ESD) You must be properly grounded when making contact with the Alcatel-Lucent 1665 DMXtend frame and handling circuit packs, disk drives, and tapes. Wrist strap ground cords should be routinely tested for the minimum 1-megohm resistance. • Plug-in storage Circuit packs should be stored in static-safe packaging or in a grounded cabinet. For additional safety precautions, please see the Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) User Operations Guide, 365-372-325. Conventions used Italic typeface denotes a particular product line or information product. Arial Bold typeface signifies a window, section, command or parameter used with the Graphical User Interface Helvetica typeface indicates a faceplate or Alcatel-Lucent 1665 DMXtend label designation, as in the ACTIVE LED on a circuit pack. Courier Bold indicates a TL1 command typed in a terminal window by the user, as in act-user:LT-DMXTEND:LUC01:ctag::DMXTND2.5G; Courier typeface indicates the system or PC response to a command. Alcatel-Lucent 1665 DMXtend Documentation Set The following table lists the documents included in the Alcatel-Lucent 1665 DMXtend documentation set. CAUTION Laser Safety When connecting fiber loops between the IN and OUT ports on optical circuit packs, always connect to the IN port first and then the OUT port. This will prevent any optical radiation from being present at the fiber end.For more detailed information and safety precautions, see Chapter 1, “Safety”.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ About this document Table 1 Alcatel-Lucent 1665 DMXtend documentation set Technical support For technical support, contact your local Alcatel-Lucent customer support team. See the Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support) for contact information. Document number/Comcode Title 365-372-330 WaveStar® CIT User Guide 365-372-324R10.0 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Applications and Planning Guide 365-372-325R10.0 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) User Operations Guide 365-372-326R10.0 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Alarm Messages and Trouble Clearing Guide 365-372-327R10.0 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Installation Manual 365-372-328R10.0 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) TL1 Message Details ED8C951-10 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Engineering and Ordering Information ED8C951-20 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Interconnect Information 109789164 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Release 10.0.0 Customer Release Notes (PDF) 109789172 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Release 10.0.0 Customer Release Notes (CD-ROM) 109789180 Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) Release 10.0.0 Eletronic Documentation Library

R10.0 365-372-327R10.0 Issue 1 January 2013 xix ............................................................................................................................................................................................................................................................ About this document How to order To order Alcatel-Lucent documents contact your local sales representative or use Online Customer Support (OLCS) (https://support.alcatel-lucent.com). How to comment To comment on this document, go to the Online Comment Form (http://infodoc.alcatel- lucent.com/comments) or email your comments to the Comments Hotline ([email protected]). Packaging collection and recovery requirements Countries, states, localities, or other jurisdictions may require that systems be established for the return and/or collection of packaging waste from the consumer, or other end user, or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the return and/or collection of the packaging waste may be established. For more information regarding collection and recovery of packaging and packaging waste within specific jurisdictions, please contact the Alcatel-Lucent Services - Environmental Health and Safety organization. Material content compliance European Union RoHS European Union (EU) Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment. This Directive applies to electrical and electronic products placed on the EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Alcatel-Lucent products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive. China RoHS The Peoples Republic of China Ministry of Information Industry has published a regulation (Order #39) and associated standards regarding restrictions on hazardous substances (China RoHS). Currently, the legislation requires all Electronic and Information Products (EIP) to comply with certain labeling and documentation requirements. Alcatel-Lucent products manufactured on or after 1 March 2007, that are intended for sale to customers in the China market, comply with these requirements.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ About this document In accordance with the People’s Republic of China Electronic Industry Standard “Marking for the Control of Pollution Caused by Electronic Information Product” (SJ/T11364- 2006), customers may access Alcatel-Lucent’s Hazardous Substances Table information at either of the following two URLs (for the convenience of our diverse customer base): • Access via the Alcatel-Lucent Corporate website at: http://www.alcatel- sbell.com.cn/live/home/index.jsp (http://www.alcatel-sbell.com.cn/ • Access via the Alcatel Shanghai Bell website at: http://www.alcatel- sbell.com.cn/wwwroot/images/upload/private/1/media/China-RoHS-HST-3.1.pdf (http://www.alcatel-sbell.com.cn/wwwroot/images/upload/ Recycling/take-back/disposal of product Electronic products bearing or referencing the symbols shown below shall be collected and treated at the end of their useful life, in compliance with applicable European Union and other local legislation. They shall not be disposed of as part of unsorted municipal waste. Due to materials that may be contained in the product and batteries, such as heavy metals, the environment and human health may be negatively impacted as a result of inappropriate disposal. Note: For electronic products put on the market in the European Union, a solid bar under the crossed-out wheeled bin indicates that the product was put on the market. Moreover, in compliance with legal requirements and contractual agreements, where applicable, Alcatel-Lucent will offer to provide for the collection and treatment of Alcatel- Lucent products bearing the logo at the end of their useful life, or products. For information regarding take-back, recycling, or disposal of equipment by Alcatel-Lucent or for equipment take-back requests, visit the Alcatel-Lucent Take-Back web page (http://www.alcatel-lucent.com/product_takeback) or contact Alcatel-Lucent Take-Back Support ([email protected]). For technical information on product treatment, consult the Alcatel-Lucent Recycling Information web page.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ 1 Safety Overview Purpose This chapter provides important safety instructions for the Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend). Contents This appendix provides information on the following topics: Laser safety System design The Alcatel-Lucent system complies with FDA/CDRH 21 CFR 1040.10 and 1040.11 as a Class I and with IEC 60825-1 as a Class 1 Optical Fiber Telecommunication laser product. The system has been designed to ensure that the operating personnel is not endangered by laser radiation during normal system operation. The safety measures specified in the Food and Drug Administration’s Center for Devices and Radiological Health (FDA/CDRH) regulations and the international standards IEC-60825 or DIN/EN 60825 are met. Please also see “Laser product classification” (p. 1-9). Laser safety 1-1 Electrostatic discharge ESD considerations 1-3 Laser product classification 1-9 Alcatel-Lucent 1665 DMXtend optical specifications 1-11

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety Potential sources of danger Beware of the following potential sources of danger which will remain despite all safety measures taken: • Laser radiation can cause damage to the skin and eyes. • Laser radiation from optical transmission systems is in a wavelength range that is invisible to the human eye. Laser warning labels The laser warning labels indicate either only the laser class or both the laser class and the maximum output power of laser radiation. The following figure shows different types of laser warning labels and their characteristics. CAUTION Do not view directly with optical instruments. CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN AND FIBER DISCONNECTED. ATTENTION RAYONNEMENT LASER DE CLASSE 1M INVISIBLE LORSQUE L’APPAREIL EST OUVERT ET QUE LA FIBRE EST DÉCONNECT E. Ne pas regarder directement au moyen d’un instrument optique. É 848950572 HAZARD LEVEL 1M 1 2 3 CLASS 1 LASER PRODUCT DANGER INVISIBLE LASER RADIATION WHEN OPEN AND FIBER DISCONNECTED Avoid direct exposure to beam Do not view beam directly with optical instruments

R10.0 365-372-327R10.0 Issue 1 January 2013 1-3 ............................................................................................................................................................................................................................................................ Safety Legend 1. Laser symbol. 2. Laser classification label. This label may show only the laser class or both the laser class and the maximum output power. 3. Laser warning label. Laser safety instructions Observe the following instructions to avoid exposing yourself and others to risk. • Read the relevant descriptions in the manuals before taking equipment into operation or carrying out any installation and maintenance work on the optical port units, and follow the instructions. Ignoring the instructions can result in exposure to dangerous radiation. • Do not view directly into the laser beam with optical instruments such as a fiber microscope, because viewing of laser emission in excess of Class 1 limits significantly increases the risk of eye damage. • Never look into the end of an exposed fiber or an open connector as long as the optical source is still switched on. • Ensure that the optical source is switched off before disconnecting optical fiber connectors. • In the event of doubt, check that the optical source is switched off by measuring with an optical power meter. • When connecting fiber loops between the IN and OUT ports on optical circuit packs, always connect to the IN port first and then the OUT port. This will prevent any optical radiation from being present at the fiber end. Electrostatic discharge ESD considerations ESD precautions Industry experience has shown that all integrated circuit packs can be damaged by static electricity that builds up on work surfaces and personnel. The static charges are produced by various charging effects of movement and contact with other objects. Dry air allows greater static charges to accumulate. Higher potentials are measured in areas with low relative humidity, but potentials high enough to cause damage can occur anywhere. CAUTION ESD hazard

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety In order to prevent damage by electrostatic discharge the following precautions should be observed when handling circuit packs: • Assume all circuit packs contain solid state electronic components that can be damaged by ESD. • When handling circuit packs (storing, inserting, removing, etc.) or when working on the backplane, always wear a grounded wrist strap such as the one shown in Figure 1-1, “Static control wrist strap” (p. 1-5) or wear a heel strap and stand on a grounded, static dissipating floor mat. If a static dissipating floor mat is used, be sure that it is clean to ensure a good discharge path. • Handle all circuit packs by the faceplate or latch and by the top and bottom outermost edges. Never touch the components, conductors, or connector pins. • Observe warning labels on bags and cartons. Whenever possible, do not remove circuit packs from antistatic packaging until ready to insert them into slots. • If possible, open all circuit packs at a static safe work position, using properly grounded wrist straps and static dissipating table mats. If a static dissipating floor mat is used, be sure that it is clean to ensure a good discharge path. • Always store and transport circuit packs in static safe packaging. Shielding is not required unless specified. • Keep all static generating materials such as food wrappers, plastics, and styrofoam containers away from all circuit packs. Upon removal from bay, immediately put circuit packs into static safe packages. • Whenever possible, maintain relative humidity above 20 percent. To reduce the possibility of ESD damage, assemblies are equipped with grounding jacks to enable personnel to ground themselves using wrist straps [Figure 1-1, “Static control wrist strap” (p. 1-5)] while handling circuit packs or working on an assembly. The jacks for connection of wrist straps are located at the lower right-hand corner of each assembly and are labeled. When grounding jacks are not provided, an alligator clip adapter enables connection to bay frame ground.

R10.0 365-372-327R10.0 Issue 1 January 2013 1-5 ............................................................................................................................................................................................................................................................ Safety Figure 1-1 Static control wrist strap TO GROUND CONNECTION

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product. When installing, operating, or maintaining this equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this product. 3. This product should be only operated from the type of power sources indicated on the marking label. 4. Connect this product only to the type of power sources recommended by Alcatel- Lucent. For information on the powering instructions, consult the Installation Manual. 5. This equipment is suitable for mounting on a concrete or other noncombustible surface only. 6. For information on proper mounting instructions, consult the Installation Manual. 7. Install only equipment identified in the Installation Manual. Use of other equipment may result in improper connection of circuitry leading to fire or injury to persons. 8. All metallic telecommunication interfaces should not leave the building premises unless connected to telecommunication devices providing primary and secondary protection, as applicable. 9. Do not use this product near water, for example, in a wet basement. 10. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. 11. Use caution when installing or modifying telecommunications lines. 12. Never install telecommunications wiring during a lightning storm. 13. Never install telecommunications connections in wet locations. 14. Never touch uninsulated telecommunications wires or terminals unless the telecommunications line has been disconnected at the network interface. 15. Never touch uninsulated wiring or terminals carrying direct current or ringing current, or leave this wiring exposed. Protect and tape uninsulated wiring and terminals to avoid risk of fire, electric shock, and injury to service personnel. 16. Never push objects of any kind into this product through slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. Never spill liquids of any kind on the product.

R10.0 365-372-327R10.0 Issue 1 January 2013 1-7 ............................................................................................................................................................................................................................................................ Safety 17. Slots and openings in the unit are provided for ventilation, to protect it from overheating, and these openings must not be blocked or covered. This product should not be placed in a built-in installation unless proper ventilation is provided. 18. To reduce the risk of an electrical shock, do not disassemble this product. Service should be performed by trained personnel only. Opening or removing covers and/or circuit boards may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electrical shock when the unit is subsequently used. 19. Some of the Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend) hardware modules contain FDA/CDRH Class I/IEC Class 1 single-mode laser products that are enclosed lightwave transmission systems. Under normal operating conditions, lightwave transmission systems are completely enclosed; nonetheless, the following precautions must be observed because of the potential for eye damage: • Do not disconnect any lightwave cable or splice and stare into the optical connectors terminating the cables. • Lightwave/lightguide operations should not be performed by a technician who has not satisfactorily completed an approved training course. • Do not use optical instruments such as an eye loupe to view a fiber or unterminated connector. • More information about laser safety can be found in the Installation Manual. 20. For a unit intended to be powered from –48 V dc voltage sources, read and understand the following: • To be powered only by Safety Extra Low Voltage (SELV) -48 V dc Sources. • Disconnect up to Two (2) power supply connections when removing power from the system. • This equipment must be provided with a readily accessible disconnect device as part of the building installation. • Ensure that there is no exposed wire when the input power cables are connected to the unit. • Installation must include an independent frame ground drop to building ground. See Alcatel-Lucent 1665 Data Multiplexer Extend (DMXtend) User Operations Guide, 365-372-325 This symbol is marked on the product, adjacent to the ground (earth) area for the connection of the ground (earth) conductor.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety • This Equipment is to be Installed Only in Restricted Access Areas on Business and Customer Premises Applications in Accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical Code, ANSI/NFPA No. 70. Other Installations Exempt from the Enforcement of the National Electrical Code May Be Engineered According to the Accepted Practices of the Local Telecommunications Utility. 21. For a unit intended to be powered from 100-120/200-240 V ac voltage sources, read and understand the following: • Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. • Do not staple or otherwise attach the power supply cord to the building surfaces. • Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. • The socket outlet should be installed near the equipment and should be readily accessible. • This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug is intended to fit only into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug. Do not use a 3-to-2-prong adapter at the receptacle. Use of this type adapter may result in risk of electrical shock and/or damage to this product. • Do not allow anything to rest on the power cord. Do not locate this product where the cord may be abused by persons walking on it. • Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the powers supply cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by qualified technician to restore the product to normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. SAVE THESE INSTRUCTIONS

R10.0 365-372-327R10.0 Issue 1 January 2013 1-9 ............................................................................................................................................................................................................................................................ Safety Laser product classification Standards compliance The product complies with both IEC standards and the Food and Drug Administration’s Center for Devices and Radiological Health (FDA/ CDRH) regulations. FDA/CDRH regulations Laser products are classified in accordance with the FDA/CDRH - 21 CFR 1010 and 1040. The classification scheme is based on the ability of the laser emission to cause injury to eye or skin during normal operating conditions. In the United States, lasers and laser systems in the infrared wavelength range (greater than 700 nm) are assigned to one of the following classes: • Class I, • Class IIIb, or • Class IV. Laser classification is dependent upon operating wavelength, output power and fiber modefield diameter (core diameter). IEC requirements The International Electro-Technical Commission (IEC) establishes standards for the electrical and electronic industries. IEC-60825 has been established for the worldwide safety of laser products. According to the IEC classification, lasers and laser systems in the infrared wavelength range (greater than 700 nm) are assigned to one of the following classes: • Class 1, • Class 3A, • Class 3B, or • Class 4. There are some major differences between the FDA/CDRH regulations and IEC: 1. The Accessible Emission Limits (AEL) are different. 2. Class 3A applies to all wavelengths. 3. Class 3B requires strict engineering controls. 4. Classification is under single fault conditions.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety Laser classes The maximum output power of laser radiation depends on the type of laser diode used. The international standards IEC-60825 or DIN/EN 60825 define the maximum output power of laser radiation for each laser class in accordance with the wavelength. Table 1-1 Laser classes Hazard level assignment Hazard level refers to the potential hazard from laser emission at any location in an end- to-end optical fiber communication system that may be accessible during service or in the event of a failure. The assignment of hazard level uses the AELs for the classes. Hazard levels for optical transmission equipment are assigned in either of the following two ways: • Actual output power from the connector or fiber cut. • If automatic power reduction is used, output power at the connector or fiber cut at one second after automatic power reduction takes place provided that maximum output and restart conditions are met. Classification of optical telecommunication equipment Optical telecommunication equipment is generally classified as IEC Class 1 or FDA/CDRH Class I, because under normal operating conditions, the transmitter ports terminate on optical fiber connectors. These are covered by a front panel to ensure protection against emissions from any energized, unterminated transmitter. The circuit packs themselves, however, may be IEC Class 1 or 3A or FDA/CDRH Class I or IIIb. Laser class Wavelength Maximum output power of laser radiation 1 1310 nm 8.85 mW 1550 nm 10 mW 3A 1310 nm 24 mW 1550 nm 50 mW 3B 1310 nm 0.5 W 1550 nm 0.5 W

R10.0 365-372-327R10.0 Issue 1 January 2013 1-11 ............................................................................................................................................................................................................................................................ Safety Alcatel-Lucent 1665 DMXtend optical specifications Overview Table 1-2 provides the optical specifications for Alcatel-Lucent 1665 DMXtend internal laser circuit packs; these packs do not use PTMs. Table 1-2 Alcatel-Lucent 1665 DMXtend optical circuit pack laser safety specifications Laser Circuit Pack Code Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class LNW31 OC-48 1310 0.0 0.0/-18.0 SM (9) LC I(LN50)/1 LNW38 OC-12 1310 -8.0 -8.0/-28.0 SM (9) LC I(LN50)/1 LNW40 OC-3 1310 -8.0 -8.0/-28.0 SM (9) LC I(LN50)/1 LNW51 OC-12 1310 +2.0 -7.0/-30.5 SM (9) LC I(LN50)/1 LNW52 OC-48 1310 +3.0 -9.0/-27.0 SM (9) LC I(LN50)/1 LNW601 OC-3 1310 0.0 0.0/-34.0 SM (9) LC I(LN50)/1

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety Table 1-3 shows the pluggable transmission module (PTM) laser safety specifications and the supported circuit packs. The following Class 1 SFP/XFP transceivers are Alcatel- Lucent approved. Table 1-3 Alcatel-Lucent 1665 DMXtend optical PTM laser safety specifications Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class 100BASE- ZX-I1 LNW74 LNW87 LNW170 1550 +2.0 -8.0/-31.0 SM (9) LC I(LN50)/1 100BASE- LX-I1 LNW63 LNW64 LNW74 LNW87 LNW170 LNW910 1310 -8.0 -8.0/-25.0 SM (9) LC I(LN50)/1 100BASE- FX-I1 LNW74 LNW87 LNW170 1310 -14.0 -14.0/-29.0 MM (50 and 62.5) LC I(LN50)/1 1000BASE- ZX-I1 LNW63 LNW64 LNW87 LNW170 LNW910 1550 +5.0 0.0/-22.5 SM (9) LC I(LN50)/1 ESCON- MM-I1 LNW73/73C 1310 -14.0 -14.4/-29.0 MM (50 and 62.5) LC I(LN50)/1 GE- 1X2XFC- LX-I1 LNW63 LNW64 LNW73/73C LNW87 LNW170 LNW705 LNW910 1310 -3.0 -3.0/-19.0 SM (9) LC I(LN50)/1 GE- 1X2XFC- SX-I1 LNW63 LNW64 LNW73/73C LNW87 LNW170 LNW705 LNW910 850 -2.5 0.0/-17.0 MM (50 and 62.5) LC I(LN50)/1

R10.0 365-372-327R10.0 Issue 1 January 2013 1-13 ............................................................................................................................................................................................................................................................ Safety BASE-TC1- electrical LNW63 LNW64 LNW87 LNW170 NA NA NA NA RJ45 NA SGEMEC1 LNW910 NA NA NA NA RJ45 NA X10GMC2 LNW910 1310 -1.0 0.5/-11.0 SM (9) LC I(LN50)/1 X10GMC4 LNW910 1550 +3.0 -1.0/-14.0 SM (9) LC I(LN50)/1 X10GMC5 LNW910 1550 +4.0 -7.0/-24.0 SM (9) LC I(LN50)/1 OC3SR1-I1 (S155I2) LNW37 LNW45 LNW55 LNW84 LNW302 LNW705 1310 -8.0 -8.0/-23.0 SM (9) LC I(LN50)/1 OC3IR1-I1 LNW37 LNW45 LNW55 LNW84 LNW302 LNW705 1310 -8.0 -15.0/-28.0 SM (9) LC I(LN50)/1 OC3LR1-I1 LNW37 LNW45 LNW55 LNW84 LNW302 LNW705 1310 -0.0 -10.0/-34.0 SM (9) LC I(LN50)/1 OC3X12X48 IR1-I1 LNW55 LNW84 1310 (OC-3) 0.0 -10.0/-18.0 SM (9) LC I(LN50)/1 1310 (OC-12/48) 0.0 0.0/-18.0 OC3X12X48 LR1-I1 LNW55 LNW84 1310 (OC-3) +3.0 -15.0/-2.0 SM (9) LC I(LN50)/1 1310 (OC-12/48) +3.0 -9.0/-2.0 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety OC12IR1-I1 LNW49 LNW55 LNW84 LNW382 LNW705 1310 -8.0 -8.0/-28.0 SM (9) LC I(LN50)/1 OC12LR1-I1 LNW49 LNW55 LNW84 LNW382 LNW705 1310 +2.0 -8.0/-28.0 SM (9) LC I(LN50)/1 OC12LR2-I1 LNW49 LNW55 LNW84 LNW382 LNW705 1550 +2.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C47EL LNW37 LNW45 LNW49 LNW55 LNW84 1471 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C49EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1491 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C51EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1511 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C53EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1531 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 1-15 ............................................................................................................................................................................................................................................................ Safety S622C55EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1551 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C57EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1571 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C59EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1591 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 S622C61EL LNW37 LNW45 LNW49 LNW55 LNW84 LNW705 1611 +5.0 -8.0/-28.0 SM (9) LC I(LN50)/1 OC48SR1-I1 LNW41 LNW55 LNW62 LNW84 LNW402 LNW705 1310 -3.0 -3.0/-18.0 SM (9) LC I(LN50)/1 OC48LR1-I1 LNW41 LNW55 LNW62 LNW84 LNW402 LNW705 1310 +3.0 -9.0/-27.0 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety OC48LR2-I1 LNW41 LNW55 LNW62 LNW84 LNW402 LNW705 1550 +3.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D23C6 LNW41 LNW55 LNW62 LNW84 LNW402 1558.983 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D25C6 LNW41 LNW55 LNW62 LNW84 LNW402 1557.363 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D27C6 LNW41 LNW55 LNW62 LNW84 LNW402 1555.747 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D31C6 LNW41 LNW55 LNW62 LNW84 LNW402 1552.524 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D33C6 LNW41 LNW55 LNW62 LNW84 LNW402 1550.918 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D35C6 LNW41 LNW55 LNW62 LNW84 LNW402 1549.315 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 1-17 ............................................................................................................................................................................................................................................................ Safety S2D37C6 LNW41 LNW55 LNW62 LNW84 LNW402 1547.715 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D45C6 LNW41 LNW55 LNW62 LNW84 LNW402 1541.349 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D47C6 LNW41 LNW55 LNW62 LNW84 LNW402 1539.766 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D49C6 LNW41 LNW55 LNW62 LNW84 LNW402 1538.186 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D53C6 LNW41 LNW55 LNW62 LNW84 LNW402 1535.036 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D55C6 LNW41 LNW55 LNW62 LNW84 LNW402 1533.465 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 S2D59C6 LNW41 LNW55 LNW62 LNW84 LNW402 1530.334 +4.0 -9.0/-28.0 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety S2G7C47LI LNW41 LNW55 LNW62 LNW84 LNW402 1471 +5.0 -8.0/NA SM (9) LC I(LN50)/1 S2G7C49LI LNW41 LNW55 LNW62 LNW84 LNW402 1491 +5.0 -8.0/NA SM (9) LC I(LN50)/1 S2G7C51LI LNW41 LNW55 LNW62 LNW84 LNW402 1511 +5.0 -8.0/NA SM (9) LC I(LN50)/1 S2G7C53LI LNW41 LNW55 LNW62 LNW84 LNW402 1531 +5.0 -8.0/NA SM (9) LC I(LN50)/1 S2G7C55LI LNW41 LNW55 LNW62 LNW84 LNW402 1551 +5.0 -8.0/NA SM (9) LC I(LN50)/1 S2G7C57LI LNW41 LNW55 LNW62 LNW84 LNW402 1571 +5.0 -8.0/NA SM (9) LC I(LN50)/1 S2G7C59LI LNW41 LNW55 LNW62 LNW84 LNW402 1591 +5.0 -8.0/NA SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 1-19 ............................................................................................................................................................................................................................................................ Safety S2G7C61LI LNW41 LNW55 LNW62 LNW84 LNW402 1611 +5.0 -8.0/NA SM (9) LC I(LN50)/1 OC192IR2- C1 LNW141 LNW603 LNW705 1550 +2.0 -1.0/-14.0 SM (9) LC I(LN50)/1 OC192IR2- I1 LNW141 LNW705 1550 +2.0 -7.0/-24.0 SM (9) LC I(LN50)/1 OC192LR2- C1 LNW141 LNW603 1550 +4.0 -7.0/-24.0 SM (9) LC I(LN50)/1 OC192SR1- C1 LNW141 LNW603 1310 -1.0 -1.0/-11.0 SM (9) LC I(LN50)/1 X10G21C5 LNW141 1560.606 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G22C5 LNW141 1559.794 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G23C5 LNW141 1558.983 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G24C5 LNW141 1558.173 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G25C5 LNW141 1557.363 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G26C5 LNW141 1556.555 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G27C5 LNW141 1555.747 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety X10G28C5 LNW141 1554.940 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G31C5 LNW141 1552.524 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G33C5 LNW141 1550.918 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G35C5 LNW141 1549.315 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G37C5 LNW141 1547.715 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G45C5 LNW141 1541.349 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G47C5 LNW141 1539.766 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G49C5 LNW141 1538.186 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G52C5 LNW141 1535.822 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G53C5 LNW141 LNW603 1535.036 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G54C5 LNW141 1534.250 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G55C5 LNW141 1533.465 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class

R10.0 365-372-327R10.0 Issue 1 January 2013 1-21 ............................................................................................................................................................................................................................................................ Safety Table 1-4 Dispersion-limited receiver sensitivity for OC-192 DWDM PTMs X10G56C5 LNW141 LNW603 1532.681 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G57C5 LNW141 1531.898 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G58C5 LNW141 LNW603 1531.116 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 X10G59C5 LNW141 1530.334 +3.0 - 8.0/Table 1 -4 SM (9) LC I(LN50)/1 Module Code Supported Circuit Pack(s) Wavelength (nm) Maximum Out Pwr (dBm) Max/Min Rcv Pwr (dBm) Fiber Type (µm) Conn Type FDA Class/ IEC Class Data Rate Receiver Sensitivity 0 ps/nm dispersion Receiver Sensitivity 1300 ps/nm dispersion Receiver Sensitivity 1600 ps/nm dispersion 9.9 Gb/s -24.0 dBm -22.0 dBm NA 10.7-11.1 Gb/s with Forward Error Correction (FEC) enabled -27.0 dBm NA -25.0 dBm

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Safety

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Part I: Physical and power installation Overview Introduction Part I covers the physical mounting of the Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend) shelf using the Horizontal Bay Mount. This section includes running and connecting power cables, interconnecting cables, alarm cables, and as required, external timing, and communication cables. Initial circuit pack installation (not seated) is also included. Part I provides a recommended checklist Table I-2 “Installation checklist” to follow when installing Alcatel-Lucent 1665 DMXtend. Use of the installation checklist is required to ensure a quality installation. All completed tasks should be checked off and those not completed should be duly noted as to the reason why. This checklist should be turned in as part of your job complete paperwork. Note: The Alcatel-Lucent 1665 DMXtend shelf does not require the installation of an additional fan shelf since the fan unit is integral to the shelf itself. Contents This part includes the following chapters: Chapter 2, “Physical installation” Chapter 3, “Cable and fiber installation” Chapter 4, “Circuit pack installation”

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical and power installation Tools, test equipment and accessories This section lists the tools, test equipment and accessories needed to perform all the procedures in this installation manual. Listed below are the required tools, test equipment and accessories. Qty. Description Comments 1 19" Mounting Brackets 849011804 The 19" mounting brackets (C849011804) must be ordered separately and are required to install the Alcatel-Lucent 1665 DMXtend in a 19" bayframe. Screwdriver(s) A screwdriver(s) with the appropriate head(s) is (are) required for securing the mounting screws, repositioning the mounting brackets, installing the interfacing cables, and for setting the circuit breakers to the OFF position. 1 Thomas & Betts* R-5648B Crimping Tool The crimping tool and wire stripper are only required if installing DS3/EC1 cables. The replacement cassette is for the wire stripper tool. 2 Paladin† Coaxial Wire Stripper R-5648B Replacement Paladin† Cassette R-5648B D5 1 Wire-Wrap Gun R-4496A The wire-wrap gun is required for terminating DS1/E1 cable and must be able to accommodate 24 gauge wire. 1 ESD Wrist Strap R-4987C A wrist strap must be worn when handling circuit packs. Use the electrostatic discharge (ESD) jack provided on the shelf. 1 Torque Wrench R-5952 A torque wrench (50-250 IN-LBS) is used when tightening the Alcatel-Lucent 1665 DMXtend shelf to the frame. It is also used when reattaching the mounting brackets to the Alcatel-Lucent 1665 DMXtend shelf. 1 Metric & Inch Series Tool Set R-6001 Because some of our Optical Networking Products (also know as Transport) may have some metric fasteners, please ensure that the proper metric tools are available. 1 Multimeter (Optional) ITE-6379C The voltmeter must be capable of measuring DC voltage in the 40 to 60 volt range. The use of the voltmeter is optional since the shelf will alarm or shut down if the proper voltage is not supplied.

R10.0 365-372-327R10.0 Issue 1 January 2013 I-3 ............................................................................................................................................................................................................................................................ Physical and power installation 1 Ohmmeter ITE-6379C An ohmmeter is required to verify that the Alcatel- Lucent 1665 DMXtend is properly grounded. 1 DS1/E1 Error Rate Test Set ITE-7113 A DS1/E1 error rate test set is required for testing of DS1/E1 cabling. A T-BERD 2209 or equivalent is recommended. 1 DS3/EC1 Error Rate Test Set ITE-7113 A DS3/EC1 error rate test set is required for testing of DS3/EC1 cabling. A T-BERD 209 or equivalent is recommended. 1 Optical Test Set (Optional) A Optical test set is required for testing of low speed optics OC3/12/48. An Omniber 718 or equivalent is recommended. 2 or 3 LC-type Optical Fiber Jumper ITE-7169 (108918269) Two optical fiber jumpers with LC type connectors are required to optically loop the Alcatel-Lucent 1665 DMXtend shelf for test purposes. In addition, for shelves containing optical circuit packs in any of the function unit slots, a single optical fiber jumper is required for testing of the individual ports. 1 15-dB LC-type LBO ITE- 7196 (108279480) LBOs are only required when optically looping the Alcatel-Lucent 1665 DMXtend shelves containing optical circuit packs in any of the function unit slots; a single 15-dB LBO is required for testing of the individual ports Noyes OFS 300-200X Optical Fiber Scope ITE-7129 This equipment may not be necessary at all locations. It is to be used when the ports need to be verified for cleanliness. If care is exercised when cleaning fibers, the optical fiber scope may not be needed 2.5mm Universal adapter cap ITE-7129 D1 For use with the Noyes OFS 300-200X Optical Fiber Scope 1.25mm Universal adapter cap ITE-7129 D2 Noyes VFS-1 ITE-7187 Video Fiber Scope1 This equipment may not be necessary at all locations. It is to be used when the ports need to be verified for cleanliness. If care is exercised when cleaning fibers, the video scope may not be needed Individual presaturated alcohol wipes ITE-7136 99% pure isopropyl alcohol Qty. Description Comments

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical and power installation PC and cable requirements for WaveStar® CIT This section lists the required equipment needed to run the WaveStar® CIT software with the Alcatel-Lucent 1665 DMXtend. 1 CLETOP Cleaning Cassette ITE-7137 Type A Reel 1 CLETOP Cleaning Cassette Replacement Reel ITE-7137 D1 Type A Reel Luminex Stick port cleaners ITE-7134 & ITE- 7135 1.25 mm and 2.5 mm sizes Luminex Cloth R-6033 5.5” x 5.5” Notes: * Registered trademark of Thomas & Betts Corporation † Registered trademark of Paladin Corporation. Qty. Description Comments Quantity Description Comments 1 Personal Computer (PC) See PC minimum requirements. 1 RS-232 Interface Cable 8-ft. long RJ45 to 9-pin D-sub serial cable (Comcode 848748869) 1 RJ45 to RJ45 Cross- over Cable

R10.0 365-372-327R10.0 Issue 1 January 2013 I-5 ............................................................................................................................................................................................................................................................ Physical and power installation PC minimum requirements It is anticipated that most customers will dedicate a laptop or personal computer (PC) to run the WaveStar® CIT software. However, any properly configured computer will also suffice. The following table shows the requirements for the computer. Note: Windows Vista is not supported. Table I-1 Computer requirements Components Minimum* Notes: * Minimum requirements are sufficient to run two to three GUI System Views, unless otherwise noted. Recommended requirements are intended to be used as a general guideline to optimize WaveStar® CIT performance. As the CIT is used with multiple NE connections and multiple NE types, the processor type and speed and the memory size will all factor into CIT performance. Recommended Processor Pentium 266 MHz Pentium IV 1 GHz RAM (1 system view) 256 MB 512 MB RAM (up to 5 system views) 512 MB 1 GB Virtual Memory 139 MB 267 MB Available Hard Disk Space† † Available hard disk space required to install and store the CIT and Generic Software and on- line help files is approximately 750 MB. During installation, an additional 100 MB is required. To store a copy of an NE generic, another 125 MB is needed for each generic 750 MB 850 MB (for all graphical packages) Video 800X600 256 Colors (8 Bit) 1024X768 16 Million Colors (24 Bit) Network Interface 10/100 baseT Network Card CD ROM Drive Required Operating System Microsoft Windows® 7 Microsoft Windows® XP Internet Browser Internet Explorer 5.0/5.5/6.0/7.0

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical and power installation Table I-2 Installation checklist Section and chapter Procedure Required Completed Yes No Part I: “Physical and power installation” Chapter 2, “Physical installation” Inspection (p. 2-5) Yes Alcatel-Lucent 1665 DMXtend center divider (p. 2-5) See Note 1 Alcatel-Lucent 1665 DMXtend shelf installation (p. 2-8) Yes Power cable installation (p. 2-13) Yes Chapter 3, “Cable and fiber installation” Inspection (p. 3-5) Yes DS1/E1 cable installation (p. 3-6) See Note 1 DS3/EC-1 cable installation (p. 3-13) See Note 1 DS1 and DS3 hybrid cable installation (p. 3-30) See Note 1 10/100BASE-T Ethernet cable installation (p. 3-36) See Note 1 IAO LAN and TCP/IP cable installation (p. 3- 41) See Note 1 Modem cable installation (p. 3-44) See Note 1 Sync cable installation (p. 3-46) See Note 1 Office alarm cable installation (p. 3-50) See Note 1 Miscellaneous (environmental) discrete telemetry cable installation (p. 3-54) See Note 1 OC-3/OC-12/OC-48/OC-192 main optical fiber cable installation (p. 3-58) See Note 1 OC-3/OC-12/OC-48 low-speed optical fiber cable installation (p. 3-61) See Note 1 100/1000BASE-X optical fiber cable installation (p. 3-62) See Note 1 CIT (RS-232) cable installation (p. 3-64) See Note 1 Final operations (p. 3-66) Yes

R10.0 365-372-327R10.0 Issue 1 January 2013 I-7 ............................................................................................................................................................................................................................................................ Physical and power installation Chapter 4, “Circuit pack installation” Powering (p. 4-2) Yes Initial circuit pack installation (p. 4-9) LNW2 (SYSCTL) installation (p. 4-10) Yes OC-3/OC-12/OC-48/OC-192 main OLIU installation (p. 4-10) Yes LNW39/LNW391 (DS1/DS3/16/3), LNW111 (3DS3) and LNW112 (16DS1) installation (optional) (p. 4-17) See Note 1 LNW7 (28DS1PM) and LNW8/LNW801 (56DS1E1) installation (optional) (p. 4-12) See Note 1 LNW16 (12DS3/EC1) and LNW19B (48DS3/EC1) installation (optional) (p. 4-13) See Note 1 LNW18 (12TMUX) and LNW20 (48TMUXDS3EC1) installation (optional) (p. 4-14) See Note 1 LNW63 (GBE PL) 4 port or LNW64 (GBE PL) 8-port installation (optional) (p. 4-20) See Note 1 LNW37 (OC-3 4 port PTM OLIU), LNW45 (OC-3 8 port PTM OLIU), or LNW603 (OC- 192 PTM OLIU) low-speed installation (p. 4- 16) See Note 1 LNW49 (OC-12 4 port PTM OLIU) low-speed installation (optional) (p. 4-18) See Note 1 LNW62 (4 OC-48 PTM OLIU) or LNW55 (OC-3/OC-12/OC-48 12/4 port OLIU) low speed installation (optional) (p. 4-19) See Note 1 LNW63 (GBE PL) 4 port or LNW64 (GBE PL) 8-port installation (optional) (p. 4-20) See Note 1 LNW73/73C (4-Fiber channel FICON/ESCON) installation (optional) (p. 4- 21) See Note 1 Section and chapter Procedure Required Completed Yes No

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical and power installation LNW74 (10/100T/F), LNW87 (FE/GBE PL), or LNW910 (FE/GBE/10GBE) installation (optional) (p. 4-22) See Note 1 LNW170 (100/1G FXS) (p. 4-23) See Note 1 LNW402 OC48 1310 nm, 1550 nm, or DWDM PTM Optics (p. 4-24) See Note 1 LNW63 (GBE PL) 4 port or LNW64 (GBE PL) 8-port installation (optional) (p. 4-20) See Note 1 LNW785 OMD5/8 8-channel low-loss DWDM optical mux/demux (p. 4-26) See Note 1 LNW43, LNW96 (apparatus blank) installation (optional) (p. 4-28) See Note 1 LNW42, LNW95 apparatus blank installation (optional) (p. 4-28) See Note 1 Notes: 1. Only required if equipped. Section and chapter Procedure Required Completed Yes No

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ 2 Physical installation Overview Purpose This section provides equipment installation instructions for the Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend) shelf using the horizontal bay mount configuration. The Alcatel-Lucent 1665 DMXtend shelves with the removable center divider can support either half width or full width cards in the Main function slots. Contents This chapter provides information on the following topics: Planning Description This section provides information about the following: • Tools, test equipment and accessories • Mounting options • Cabling checklist Planning 2-1 Inspection 2-5 Alcatel-Lucent 1665 DMXtend center divider 2-5 Alcatel-Lucent 1665 DMXtend shelf installation 2-8 Power cable installation 2-13 Final operations 2-17

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation Tools, test equipment and accessories Listed below are the tools, test equipment and accessories necessary to perform the procedures in this section. Mounting options The Horizontal Bay Mount mounting brackets on the Alcatel-Lucent 1665 DMXtend are designed to allow for mounting in the following: • Standard 23-inch wide network bay frames The recommended network bay frames are the ED-8C500-50 and the ED-8C501-50 (rear access only). Quantity Description Comments 1 19" Mounting Brackets 849011804 The 19" mounting brackets (849011804) must be ordered separately and are required to install the Alcatel-Lucent 1665 DMXtend in a 19" bayframe. Screwdriver(s) A screwdriver(s) with the appropriate head(s) is (are) required for securing the mounting screws, repositioning the mounting brackets, installing the interfacing cables, and for setting the circuit breakers to the OFF position. 1 ESD Wrist Strap R-4987C A wrist strap must be worn when handling circuit packs. Use the electrostatic discharge (ESD) jack provided on the shelf. 1 Multimeter (Optional) ITE-6379 The voltmeter must be capable of measuring DC voltage in the 40 to 60 volt range. The use of the voltmeter is optional since the shelf will alarm or shut down if the proper voltage is not supplied. 1 Torque Wrench ITE-5952 A torque wrench (50-250 IN-LBS) is used when tightening the Alcatel-Lucent 1665 DMXtend shelf to the frame. It is also used when reattaching the mounting brackets to the Alcatel-Lucent 1665 DMXtend shelf. 1 Metric & Inch Series Tool Set R - 6001 Because some of our Optical Networking Products (also know as Transport) may have some metric fasteners, please ensure that the proper metric tools are available. 1 Ohmmeter ITE-6379 An ohmmeter is required to verify that the Alcatel- Lucent 1665 DMXtend is properly grounded.

R10.0 365-372-327R10.0 Issue 1 January 2013 2-3 ............................................................................................................................................................................................................................................................ Physical installation • Mounted in 23-inch seismic network bay frame The ED-8C800-50 and ED-8C801-50 seismic network bay frames are designed for use in all earthquake zones, and in general, do not require top support at the 7-foot level. These frames meet Pacific Bell Equipment Framework Standard PBS-000-102PT. • 19-inch bay frames • 23-inch wide EIA-Type bay frames Rear cover assembly This section describes the optional rear cover assembly kits for both Alcatel-Lucent 1665 DMXtend shelves, (Bay Mount Kit number 849001060) or Alcatel-Lucent 1665 DMXtend shelves (Shelf mount Kit number 849001367). Both kit assemblies will fit either the 19" or 23" bracket assemblies. Figure 2-1 shows the shelf mount Kit assembly. Note: The shelves (Shelf mount Kit number 849001367) have four pre-drilled holes in the shelf assembly backplane. If the shelf assembly backplane have the four non- drilled holes, then the bay mount kit (Bay Mount Kit number 849001060) must be used. Shelf mount rear cover Figure 2-1 Shelf mount rear cover kit 849001367

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation Bay mount rear cover Figure 2-2 Bay mount rear cover kit 849001060 Note: The rear bay cover requires the front mounting configuration of the Alcatel- Lucent 1665 DMXtend shelf. This is mounting the shelf on the front of the bay with 5 inches of the shelf protruding from the front of the bay. Cabling checklist This section briefly describes cabling information, including the number of particular cables required. For information regarding available cable lengths and ordering comcodes, see the tables in this chapter. Table 2-1, “Cable requirements and options” (p. 2-4) lists available cables along with the required number (if any). Table 2-1 Cable requirements and options 1. One -48VA and -48VB main power feeder is required per shelf. The shelf requires the use of a right angle power connector on each feed. Cable assembly description Required See note Power Yes 1

R10.0 365-372-327R10.0 Issue 1 January 2013 2-5 ............................................................................................................................................................................................................................................................ Physical installation Inspection Description Perform the following procedure before installing the Alcatel-Lucent 1665 DMXtend shelf. Steps ........................................................................................................................................................................................................................ 1 Inspect the shelf for visible damage including bent or touching backplane pins. Note: If any backplane pins are damaged, see Appendix D, “Backplane pin replacement” for instructions on repairing the damaged pin(s). ........................................................................................................................................................................................................................ 2 Each Alcatel-Lucent 1665 DMXtend shelf comes with an installation kit. The bag containing the kit is attached inside the Alcatel-Lucent 1665 DMXtend shelf. The kit contains the following items: Verify that the kit is available and contains the items listed above. ........................................................................................................................................................................................................................ 3 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S Alcatel-Lucent 1665 DMXtend center divider Description The Alcatel-Lucent 1665 DMXtend shelves, comcode 849031372, come shipped with center dividers which can support half-width cards. The center dividers are removed for full-width cards. This section describes the procedure to remove the center dividers on a Alcatel-Lucent 1665 DMXtend shelf if supporting full width cards. Quantity Description 6 Thread Cutting Screws 1 ESD Jack stud 1 Caution Label

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation New installation The procedure below describes how to remove the center dividers for new installations. Steps The figure below shows the new Alcatel-Lucent 1665 DMXtend shelf with the center dividers inserted. Note: The center dividers come equipped with a spring clip CC849027222 not shown in Figure 2-3, “Center divider” (p. 2-6) that latches the dividers together. Remove this spring clip by inserting a finger into the hole and pulling gently away from the shelf. Keep this spring clip available if there is ever a need to reinstall the center divider for the use of half-width cards in the shelf. Figure 2-3 Center divider ........................................................................................................................................................................................................................ 1 To remove the top center divider, depress the spring clip latch located on top of the divider and slide the divider out. ........................................................................................................................................................................................................................ 2 Remove the bottom center divider by depressing the bottom spring clip and sliding the divider out. ........................................................................................................................................................ E N D O F S T E P S Existing installation This procedure is used to remove the center dividers if circuit packs are installed above or below the dividers and the spring clip is not accessable. Center Divider Spring clip

R10.0 365-372-327R10.0 Issue 1 January 2013 2-7 ............................................................................................................................................................................................................................................................ Physical installation Steps The figure below shows the Alcatel-Lucent 1665 DMXtend shelf with both center dividers inserted and a working circuit pack installed above the top divider. Figure 2-4 Center divider with circuit packs installed. ........................................................................................................................................................................................................................ 1 Using a small flat screwdriver, separate the padding as shown in Figure 2-4, “Center divider with circuit packs installed.” (p. 2-7). ........................................................................................................................................................................................................................ 2 Insert the screwdriver approximately two thirds of the way up from the bottom of the top divider and depress the latch. ........................................................................................................................................................................................................................ 3 Gently slide out the center divider. ........................................................................................................................................................................................................................ 4 Repeat for the bottom center divider if necessary. The latch on the bottom divider moves bottom to top. ........................................................................................................................................................ E N D O F S T E P S

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation Alcatel-Lucent 1665 DMXtend shelf installation Description As an example of the Alcatel-Lucent 1665 DMXtend shelf installation, the following steps describe mounting the shelf from the front of a 23-inch bay frame. Mounting from the rear of a 23-inch bay frame or from the front/rear of a 19-inch bay frame is similar with the exception of the position of the side brackets. Positioning of the side brackets is also specified. Note: This section requires previous bay frame installation and grounding. Note: If the Alcatel-Lucent 1665 DMXtend shelf is to be used in an outside cabinet with no exchange of outside air, the air filter must be removed. Steps ........................................................................................................................................................................................................................ 1 Position the Alcatel-Lucent 1665 DMXtend shelf on a stable work surface. ........................................................................................................................................................................................................................ 2 Open the front cover, remove the installation kit bag, and remove the caution label from the bag. ........................................................................................................................................................................................................................ 3 Apply the label to the shelf in a position where it will be visible when the shelf is mounted in the bayframe. Note: The recommended position is on the left side of the inside of the front cover, but the customer may position it to fit their local practices as long as it is visible when accessing the front of the Alcatel-Lucent 1665 DMXtend shelf. ........................................................................................................................................................................................................................ 4 Close and latch the front cover.

R10.0 365-372-327R10.0 Issue 1 January 2013 2-9 ............................................................................................................................................................................................................................................................ Physical installation ........................................................................................................................................................................................................................ 5 Determine the mounting configuration for the Alcatel-Lucent 1665 DMXtend shelf: • Type of bay frame (23-inch or 19-inch wide) • Mounting position (front or rear) • Position in bay (bottom to top). Note: The Alcatel-Lucent 1665 DMXtend shelf is shipped with the mounting brackets positioned for mounting to the front of a 23-inch wide network bay frame with a 5 in. setback. The Alcatel-Lucent 1665 DMXtend shelf mounting brackets may have to be repositioned and remounted, depending on the frame type and mounting position (front or rear). ........................................................................................................................................................................................................................ 6 If necessary, reposition the shelf mounting brackets accordingly. For 23-inch frame, front or rear mounting, see Figure 2-5, “Alcatel-Lucent 1665 DMXtend mounting bracket positions - 23-Inch/19-Inch frame” (p. 2-10). Note: The 19" mounting brackets (C849011804) must be ordered separately and are required to install the Alcatel-Lucent 1665 DMXtend in a 19" bayframe. For 19-inch frame, front or rear mounting, see Figure 2-5, “Alcatel-Lucent 1665 DMXtend mounting bracket positions - 23-Inch/19-Inch frame” (p. 2-10).

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation Figure 2-5 Alcatel-Lucent 1665 DMXtend mounting bracket positions - 23-Inch/19- Inch frame ........................................................................................................................................................................................................................ 7 Determine the position that the Alcatel-Lucent 1665 DMXtend shelf will be mounted. Note: Start at the bottom of the bay and add shelves from bottom to top. 6.0 in. 5.0 in. 8.0 in. Front Mount Left Side Front Mount Left Side Rear Mount Left Side Front Front Front

R10.0 365-372-327R10.0 Issue 1 January 2013 2-11 ............................................................................................................................................................................................................................................................ Physical installation Fiber duct This section will describe how to install an optional fiber duct. Note: If a fiber duct is being used to diversify fiber, a 1-inch space is required to accommodate the duct below the existing Alcatel-Lucent 1665 DMXtend. Use the Assembly Fiber Duct kit drawing 848949152 to attach the duct to the Alcatel-Lucent 1665 DMXtend. See Figure 2-6, “Fiber duct mounting” (p. 2-11). Figure 2-6 Fiber duct mounting ........................................................................................................................................................................................................................ 8 Position the Alcatel-Lucent 1665 DMXtend shelf in the frame and secure the shelf to the frame using the thread-forming screws included with the shelf (3 screws per side). Tighten the screws to 21 in.-lb. (minimum)/30 in.-lb. (maximum). Note: There is a jumper on the fan controller board, at the corner closest to the top- rear of the chassis as installed. It is labeled "FILT BLK" and the two positions are "ENABLE" and "DISABLE." The fan ships with the jumper in the disable position which prevents the filter alarm from working. To enable the filter alarm, move the jumper to the "ENABLE" position. This is the only jumper on the board. The OSP cabinet must be engineered so that the Alcatel-Lucent 1665 DMXtend does not impede air flow to other equipment in the cabinet. The OSP cabinet must be engineered to provide a two inch open space on the left and right sides of the Alcatel- Lucent 1665 DMXtend for air flow. Mounting frame and flanges may intrude on this space. Note: Be sure to mount the shelf using the thread-forming screws provided with the shelf to ensure a solid ground connection from the bay to the shelf. Note: For bays that use power coat paint e.g., most 19" bays, studies on that type of paint indicate that the material is not always removed cleanly using the thread forming screws and can create a poor ground, thus we recommend a secondary ground be used.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation The secondary ground would consist of a 12 AWG wire from the UL (Green M5 Screw) safety ground on the lower left side of the rear of the shelf to the bayframe (where the bayframe has been scraped clean of paint and treated with no-ox) or directly to the office ground. See Figure 2-7, “Safety ground screw.” (p. 2-12). Figure 2-7 Safety ground screw. ........................................................................................................................................................................................................................ 9 Mount the ESD Jack Stud on the rear of the bayframe where it will be accessible when accessing the rear of the shelf. ........................................................................................................................................................................................................................ 10 If fiber spools are to be used, attach the spools to the Alcatel-Lucent 1665 DMXtend using the Fiber Spool Bracket Kit drawing 848949152. Attach the bracket to the shelf first and then the top fiber spool to the bracket. The lower fiber spool will need to overlap the top spool to snap into place. Run the excess fiber per office practices around the spools to minimize the bend radius. See Figure 2-8, “Fiber spools” (p. 2-13). ........................................................................................................................................................................................................................ 11 If Alcatel-Lucent fiber ducts are used, see Figure 2-8, “Fiber spools” (p. 2-13). All high- speed fibers are to be run in the duct closest to the shelf for both left and right ducts. The next two ducts away from the shelf are for low-speed fibers.

R10.0 365-372-327R10.0 Issue 1 January 2013 2-13 ............................................................................................................................................................................................................................................................ Physical installation Figure 2-8 Fiber spools ........................................................................................................................................................................................................................ 12 Verify with an ohmmeter that the Alcatel-Lucent 1665 DMXtend shelf is grounded to the bay frame. Measure between the Alcatel-Lucent 1665 DMXtend shelf mounting bracket and the office ground lug on the bay frame. Requirement: The ohmmeter reads less than 1 ohm. ........................................................................................................................................................................................................................ 13 Verify with an ohmmeter that the ESD Jack Stud mounted at the rear of the shelf is grounded to the bay frame. Measure between the ESD Jack Stud and the office ground lug on the bay frame. Requirement: The ohmmeter reads less than 1 ohm. ........................................................................................................................................................................................................................ 14 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S Power cable installation Description This section provides instructions on installing the power cable and cable bracket for the Alcatel-Lucent 1665 DMXtend shelf. Two feeders (A and B) are required from the battery distribution fuse board (BDFB) or battery distribution circuit breaker bay (BDCBB) to the Alcatel-Lucent 1665 DMXtend bay.

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation Table 2-2, “Power cable assemblies” (p. 2-16) and Table 2-3, “Power connections” (p. 2-16) lists the available power cable assemblies and power connections, respectively. Steps ........................................................................................................................................................................................................................ 1 Connect the A and B power cables to the A and B power connector housings on the back of the Alcatel-Lucent 1665 DMXtend Shelf. See Figure 2-9, “Power connection” (p. 2-14). Figure 2-9 Power connection ........................................................................................................................................................................................................................ 2 Route the power cable out of the bay and toward the BDCBB or BDFB, stacking the cable in the bay. Note: The Alcatel-Lucent 1665 DMXtend is powered by -48 V DC. ........................................................................................................................................................................................................................ 3 Splice feeders from the BDCBB or BDFB to the Alcatel-Lucent 1665 DMXtend power cable. See Table 2-3, “Power connections” (p. 2-16). and should be labeled as follows; CAUTION Verify that the BDCBB breakers are off or that the BDFB fuses are not installed. CAUTION Ensure that the four parts of the terminal inside the connector attached to the power cable are properly aligned before inserting the connector into the power connector housing. Failure to do so may result in damage to the connector. CAUTION Verify that the BDCBB breakers are off or that the BDFB fuses are not installed.

R10.0 365-372-327R10.0 Issue 1 January 2013 2-15 ............................................................................................................................................................................................................................................................ Physical installation Note: Four wires are spliced to the power cables. 1. BAT A 2. BAT A RTN 3. BAT B 4. BAT B RTN Note: Each feeder at the BDCBB or BDFB should be fused for 25 amperes for bay arrangements and 15 amperes for a single shelf. ........................................................................................................................................................................................................................ 4 Leave the BDCBB breakers off or BDFB fuses out until you are ready to perform the procedures in Chapter 4, “Circuit pack installation” of this manual. ........................................................................................................................................................................................................................ 5 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation Table 2-2 Power cable assemblies Table 2-3 Power connections Description Cable assembly # Cable length (feet) Jacket color Alcatel-Lucent 1665 DMXtend backplane connections Power Cable Kits with Right Angle Connectors and Two 6 Gauge cables 848929493 85 One Red and One Blue Connectors on rear of the shelf (BAT A and BAT B) 848929501 100 Power Cable Kits with Right Angle Connectors and Two 8 Gauge cables 848929519 55 848929527 100 Power Cable Kits with Right Angle Connectors and 10 Gauge cables 848929535 12 848929543 50 848929550 75 848929568 100 848841839 12 Has far end connectors for a power distribution panel 14 AWG 848999496 15 Alcatel- Lucent 1665 DMXtend bkpl conn. Shelf power connectors Pin # Color Designation Name Cable Wire P10 BAT A 1 Red R -48VA BAT A 2 W -48RTNA BAT A RTN P11 BAT B 1 Blue R -48VB BAT B 2 W -48RTNB BAT B RTN

R10.0 365-372-327R10.0 Issue 1 January 2013 2-17 ............................................................................................................................................................................................................................................................ Physical installation Final operations Description Final check on equipment installation. Steps ........................................................................................................................................................................................................................ 1 Verify that all the power cables are properly dressed/connected. ........................................................................................................................................................................................................................ 2 Verify that all power cables are properly labeled. ........................................................................................................................................................................................................................ 3 Replace rear cover on shelf if ordered. ........................................................................................................................................................................................................................ 4 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S

R10.0 365-372-327R10.0 Issue 1 January 2013 ............................................................................................................................................................................................................................................................ Physical installation

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ 3 Cable and fiber installation Overview Purpose This section provides cabling instructions for the Alcatel-Lucent 1665 Data Multiplexer Extend (Alcatel-Lucent 1665 DMXtend) shelf using the horizontal bay mount configuration. The Alcatel-Lucent 1665 DMXtend shelves with the removable center divider can support either half width or full width cards in the Main function slots. Note: Ensure only ANGLED LC connectors appear at IN ports of optical circuit packs. The “ANGLED” is referring to the rotating boot on the connector and not the connector. APC or Angled Polished Connectors are not supported. Contents This chapter provides information on the following topics Planning 3-2 Connector references 3-4 Inspection 3-5 DS1/E1 cable installation 3-6 DS3/EC-1 cable installation 3-13 DS1 and DS3 hybrid cable installation 3-30 10/100BASE-T Ethernet cable installation 3-36 IAO LAN and TCP/IP cable installation 3-41 Modem cable installation 3-44 Sync cable installation 3-46 Office alarm cable installation 3-50

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Planning Description This section provides information about the following: • Tools, test equipment and accessories • Mounting options • Cabling checklist Tools, test equipment and accessories Listed below are the tools, test equipment and accessories necessary to perform the procedures in this section. Miscellaneous (environmental) discrete telemetry cable installation 3-54 OC-3/OC-12/OC-48/OC-192 main optical fiber cable installation 3-58 OC-3/OC-12/OC-48 low-speed optical fiber cable installation 3-61 100/1000BASE-X optical fiber cable installation 3-62 CIT (RS-232) cable installation 3-64 Final operations 3-66 Quantity Description Comments Screwdriver(s) A screwdriver(s) with the appropriate head(s) is (are) required for securing the mounting screws, repositioning the mounting brackets, installing the interfacing cables, and for setting the circuit breakers to the OFF position. 1 Thomas & Betts1 R-5648B Crimping Tool 1. The crimping tool, wire stripper and soldering iron are only required if installing DS3/EC-1 cables. The replacement cassette is for the wire stripper tool. 2 Paladin2 Coaxial Wire Stripper R-5648B D5 Replacement Paladin2 Cassette R-5648B D5 1 Wire-Wrap Gun R-4496A The wire-wrap gun is required for terminating DS1/E1 cable and must be able to accommodate 24 gauge wire.

R10.0 365-372-327R10.0 Issue 1 January 2013 3-3 ........................................................................................................................................................................ Cable and fiber installation Cabling checklist This section briefly describes cabling information, including the number of particular cables required. For information regarding available cable lengths and ordering comcodes, see the tables in this chapter. Table 3-1, “Cable requirements and options” (p. 3-3) lists available cables along with the required number (if any). Table 3-1 Cable requirements and options 1 ESD Wrist Strap R-4987C A wrist strap must be worn when handling circuit packs. Use the electrostatic discharge (ESD) jack provided on the shelf. 1 Multimeter (Optional) ITE-6379 The voltmeter must be capable of measuring DC voltage in the 40 to 60 volt range. The use of the voltmeter is optional since the shelf will alarm or shut down if the proper voltage is not supplied. Notes: 1 Registered trademark of Thomas & Betts Corporation 2 Registered trademark of Paladin Corporation. Quantity Description Comments Cable assembly description Required See note CIT Yes 1 DS1/E1 Optional 2 DS3/EC-1 Optional 3, 4 DS1/DS3 Hybrid Optional 5 Office Alarm Optional 6 Office Alarm Mult Optional 6 Miscellaneous Discrete Optional LAN 10BASE-T (Crossover) Optional 7 LAN 10BASE-T (Straight Through) Optional 7 Sync Timing Optional Modem Optional

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation 1. One CIT Cable Assembly is required for PC interface with the Alcatel-Lucent 1665 DMXtend (not included with equipment). 2. Two DS1/E1 Cable Assembly are required for each D or G function unit group that will support additional DS1/E1 traffic using the LNW8/801. Each DS1/E1 Cable Assembly consists of two separate cable assemblies, both containing 28 pairs of 24 gauge cable. One cable is for input and the other cable is for output. 3. One DS3/EC-1 Cable Assembly is required for each D or G function unit group that will support 12 DS3’s of traffic. Each DS3/EC-1 Cable Assembly consists of two separate cable assemblies, both containing 735A cables. One cable consists of 12 inputs and the other cable consists of 12 outputs. 4. Two DS3/EC-1 Cable Assembly are required for each D or G function unit group that will support additional DS3/EC-1 traffic using the LNW19B or LNW20. Each DS3/EC-1 Cable Assembly consists of two separate cable assemblies, both containing 735A cables. One cable consists of 24 inputs and the other cable consists of 24 outputs. 5. One DS1/DS3 Hybrid Cable Assembly is required for A/B function unit Group to support use of the LNW39 (16DS1/3DS3), LNW84 (16DS1/3DS3), LNW111 (3DS3), LNW112 (16DS1), and LNW391 (16DS1/3DS3) Hybrid. Each DS1/DS3 Hybrid Cable Assembly consists of two separate cable assemblies, both containing 28 pairs of 24 gauge cable a Coaxial 735A cable. One cable is for input and the other cable is for output. 6. When cabling the Alcatel-Lucent 1665 DMXtend for office alarm applications, one Office Alarm Cable Assembly is required for the bottom Alcatel-Lucent 1665 DMXtend shelf in a bay frame. One Office Alarm Mult Cable Assembly is required for each additional Alcatel-Lucent 1665 DMXtend shelf in the bay frame. For example, if four Alcatel-Lucent 1665 DMXtend shelves are located in a single 7-foot bay frame, one Office Alarm Cable Assembly and three Office Alarm Mult Cable Assemblies are required. 7. These cables are used for IAO LAN (OSI/TCP-IP)/Front LAN (OSI/TCP-IP) connection (J16 and Front LAN port). LAN 10BASE-T cross over cable should be used if the shelf is directly connected to a PC and LAN 10BASE-T straight through cable should be used if shelf is connected to a hub. Connector references Description Figure 3-1 provides the pinouts of some of the connectors used to interface with the Alcatel-Lucent 1665 DMXtend.

R10.0 365-372-327R10.0 Issue 1 January 2013 3-5 ........................................................................................................................................................................ Cable and fiber installation Figure 3-1 Connector types and pinouts Inspection Description Perform the following procedure before installing the Alcatel-Lucent 1665 DMXtend cables. Steps ................................................................................................................................................ 1 Inspect the shelf for visible damage including bent or touching backplane pins. DB-9 male-type connector DB-15 male-type connector DB-25 male-type connector DB-62 male-type connector 1 5 6 9 1 8 9 15 1 13 14 25 1 21 43 62 22 42 DB-9 female-type connector DB-15 female-type connector DB-25 female-type connector DB-62 female-type connector 1 5 6 9 8 1 15 9 13 1 25 14 21 1 62 43 42 22 RJ-45 type connector 1 8 1 8

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Note: If any backplane pins are damaged, see Appendix D, “Backplane pin replacement” for instructions on repairing the damaged pin(s). ................................................................................................................................................ 2 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S DS1/E1 cable installation Description This section describes how to connect the DS1/E1 transmission cables for function group D or G, to the shelf, route the cables out of the bay and connect the cables to the DSX. Perform this procedure if DS1/E1 cables are required. Note: When cabling the Alcatel-Lucent 1665 DMXtend to a DSX, the DSX becomes an extension of the Alcatel-Lucent 1665 DMXtend backplane connections. Thus the IN on the Alcatel-Lucent 1665 DMXtend backplane connects to the IN of the DSX and the OUT of the Alcatel-Lucent 1665 DMXtend backplane connects to the OUT of the DSX respectively. The cables have connectors at the Alcatel-Lucent 1665 DMXtend shelf end and must be wire-wrapped at the DSX end. A total of two function groups fully cabled will have 112 DS1/E1 drop capacity. Note: The 112 DS1 drops do not include the 16 port DS1 drop available when using the LNW39/LNW391 DS1/DS3/16/3 combo card in slot A/B or the LNW84. Instructions for cabling slot A/B are provided in “DS1 and DS3 hybrid cable installation” (p. 3-30). Note: The connectorized cable end is grounded to the Alcatel-Lucent 1665 DMXtend frame ground through the backplane. Alcatel-Lucent recommends that the shield at both ends of the DS1/E1 cable be grounded. Ground at the DSX end per office requirements. Steps ................................................................................................................................................ 1 See the engineering job specification. Obtain the DS1/E1 cables per Table 3-2, “DS1/E1 cable assemblies” (p. 3-9) and note the function group where each cable will be used.

R10.0 365-372-327R10.0 Issue 1 January 2013 3-7 ........................................................................................................................................................................ Cable and fiber installation Label the cables, indicating bay, shelf, function group (D or G) and direction (IN or OUT of the bay) at each end. ................................................................................................................................................ 2 Connect the function group cables at the Alcatel-Lucent 1665 DMXtend end, carefully matching the correct connector with the appropriate backplane connectors as shown in Figure 3-2, “DS1/E1 cable connectors” (p. 3-7). Note: DS1/E1 cable retaining screws must be tightened to a maximum of 6.5 in-lb. Do not overtighten. Note: The first 28 DS1/E1s of a Function Group must be connected to the right side connectors (J1D, J3D, J7G, and J9G). An additional capacity of 28 DS1/E1s, 29-56, are used when the LNW8 circuit pack is used. The second 28 DS1/E1s of a Function Group are connected to the backplane (J2D, J4D, J8G, and J10G). Note: The DS1/E1 cables that connect to the right side connectors (J1D, J3D, J7G, and J9G) are different from the cables that connect to the connectors in the center of the backplane (J2D, J4D, J8G, and J10G). See Table 3-2, “DS1/E1 cable assemblies” (p. 3-9) for more information. Figure 3-2 DS1/E1 cable connectors ................................................................................................................................................ 3 Route the cables along the backplane and out of the bay to the DSX. Note: Cables from J1D, J3D, J7G, and J9G route to the right of the shelf (when facing the rear of the shelf) and up the bay frame. See Figure 3-3, “DS1/E1 cable routing to the right” (p. 3-8). Cables from J2D, J4D, J8G, and J10G route to the left of the shelf (when facing the rear of the shelf) and up the bay frame. See Figure 3-4, “DS1/E1 cable routing to the left” (p. 3-8).

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Note: When dressing the cables from the connectors in the center of the shelf be sure to allow for access to connectors to the left or right of the center connectors depending on whether cable dresses to the right or the left. See Figure 3-4, “DS1/E1 cable routing to the left” (p. 3-8). Figure 3-3 DS1/E1 cable routing to the right Figure 3-4 DS1/E1 cable routing to the left ................................................................................................................................................ 4 Route the cables along the cable rack and into the terminating bay. ................................................................................................................................................ 5 Remove slack and cut the DS1/E1 cables to the desired length at the DSX.

R10.0 365-372-327R10.0 Issue 1 January 2013 3-9 ........................................................................................................................................................................ Cable and fiber installation ................................................................................................................................................ 6 Referring to Table 3-3, “DS1 transmission connections” (p. 3-11), carefully observe color codes and wire-wrap the cables at the DSX. ................................................................................................................................................ 7 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S Table 3-2 DS1/E1 cable assemblies Cable length (feet) Cable assembly # Description Alcatel-Lucent 1665 DMXtend backplane connections 10 848954988 20 848955001 30 848923074 Function Group G DS1/E1 In (CA1) and DS1/E1 Out (CA2) Cable Function Group D DS1/E1 In (CA1) and DS1/E1 Out (CA2) Cable These cables route to the left (as viewed from the rear of the shelf) and should be used with connectors J2D (IN), J4D (OUT) and J8G (IN), J10G (OUT) 50 848548327 75 848923082 100 848548335 125 848923090 150 848548343 175 848923108 200 848923116 250 848548350 350 848790762 450 848548368 550 848790770 655 848790788

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation 10 848954962 Function Group G DS1/E1 In (CA1) and DS1/E1 Out (CA2) Cable Function Group D DS1/E1 In (CA1) and DS1/E1 Out (CA2) Cable These cables route to the right (as viewed from the rear of the shelf) and should be used with connectors J1D (IN), J3D (OUT) and J7G (IN), J9G (OUT) 20 848954970 30 848934964 50 848912473 75 848934972 100 848912564 125 848934980 150 848912648 175 848934998 200 848935003 250 848912671 350 848912978 450 848912986 550 848913000 655 848935011 Notes: 1. Each Cable Assembly # is a kit that contains 2 cables. For Input connections use cable CA1 (DS1/E1 IN) and for Output connections use cable CA2 (DS1/E1 OUT). 2. Each Cable Assembly # that routes to the right (when facing the rear of the shelf), listed includes all the DS1/E1 cables for one function group using the 28DS1 card. 3. In addition to each Cable Assembly # that route to the right (when facing the rear of the shelf), one Cable Assembly # of cables that route to the left (when facing the rear of the shelf), must be ordered for the additional capacity of the 56DS1/E1 card. 4. Alcatel-Lucent 1665 DMXtend connectors J1D through J4D and J7G through J10G can be used for either DS1/E1 or DS3/EC-1 cabling. 5. Cables are terminated in J1D through J4D and J7G through J10G connectors at the Alcatel-Lucent 1665 DMXtend end and unterminated at the other end for wire-wrap installation. 6. The cable connectors are 62 pins D-Sub male-type connectors and fit into J1D through J4D and J7G through J10G. 7. The DS1/E1 cables are 24 Gauge. Cable length (feet) Cable assembly # Description Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 3-11 ........................................................................................................................................................................ Cable and fiber installation Table 3-3 DS1 transmission connections DSX-1 connections Alcatel-Lucent 1665 DMXtend backplane connections G r o u p ChanD S1 T/R term T/R color 62-Pin conn. pin# T/R Function group D conn. Function group G conn. In Out In Out 1 1 (1) 2 (2) 3 (3) 4 (4) B8/B7 B6/B5 B4/B3 B2/B1 W/BL¹ W/O¹ W/G¹ W/BR 19/40 18/39 60/59 17/38 J1D D In J3D D Out J7G G In J9G G Out 2 1 (5) 2 (6) 3 (7) 4 (8) B8/B7 B6/B5 B4/B3 B2/B1 W/S R/BL R/O R/G 58/57 16/37 15/36 14/35 3 1 (9) 2 (10) 3 (11) 4 (12) B8/B7 B6/B5 B4/B3 B2/B1 R/BR R/S BK/BL BK/O 56/55 13/34 54/53 12/33 4 1 (13) 2 (14) 3 (15) 4 (16) B8/B7 B6/B5 B4/B3 B2/B1 BK/G BK/BR BK/S Y/BL 11/32 10/31 52/51 9/30 5 1 (17) 2 (18) 3 (19) 4 (20) B8/B7 B6/B5 B4/B3 B2/B1 Y/O Y/G Y/BR Y/S 50/49 8/29 7/28 6/27 6 1 (21) 2 (22) 3 (23) 4 (24) B8/B7 B6/B5 B4/B3 B2/B1 V/BL V/O V/G V/BR 48/47 5/26 46/45 4/25

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation 7 1 (25) B8/B7 V/S 3/24 2 (26) 3 (27) 4 (28) B6/B5 B4/B3 B2/B1 W/BL¹ W/O¹ W/G¹ 2/23 44/43 1/22 1 1 (29) 2 (30) 3 (31) 4 (32) B8/B7 B6/B5 B4/B3 B2/B1 W/BL1 W/O1 W/G1 W/BR 19/40 18/39 60/59 17/38 J2D D In J4D D Out J8G G In J10G G Out 2 1 (33) 2 (34) 3 (35) 4 (36) B8/B7 B6/B5 B4/B3 B2/B1 W/S R/BL R/O R/G 58/57 16/37 15/36 14/35 3 1 (37) 2 (38) 3 (39) 4 (40) B8/B7 B6/B5 B4/B3 B2/B1 R/BR R/S BK/BL BK/O 56/55 13/34 54/53 12/33 4 1 (41) 2 (42) 3 (43) 4 (44) B8/B7 B6/B5 B4/B3 B2/B1 BK/G BK/BR BK/S Y/BL 11/32 10/31 52/51 9/30 5 1 (45) 2 (46) 3 (47) 4 (48) B8/B7 B6/B5 B4/B3 B2/B1 Y/O Y/G Y/BR Y/S 50/49 8/29 7/28 6/27 6 1 (49) 2 (50) 3 (51) 4 (52) B8/B7 B6/B5 B4/B3 B2/B1 V/BL V/O V/G V/BR 48/47 5/26 46/45 4/25 DSX-1 connections Alcatel-Lucent 1665 DMXtend backplane connections G r o u p ChanD S1 T/R term T/R color 62-Pin conn. pin# T/R Function group D conn. Function group G conn. In Out In Out

R10.0 365-372-327R10.0 Issue 1 January 2013 3-13 ........................................................................................................................................................................ Cable and fiber installation DS3/EC-1 cable installation Description This section describes how to connect the DS3/EC-1 cables to the Alcatel-Lucent 1665 DMXtend shelf and route the cables out of the bay and to the DS3/EC-1 terminating equipment.This procedure covers both the 12 cable and the 24 cable DS3/EC1 cables. Perform this procedure if DS3/EC-1 cables are required. Note: When cabling the Alcatel-Lucent 1665 DMXtend to a DSX, the DSX becomes an extension of the Alcatel-Lucent 1665 DMXtend backplane connections. Therefore, the IN on the Alcatel-Lucent 1665 DMXtend backplane connects to the IN of the DSX and the OUT of the Alcatel-Lucent 1665 DMXtend backplane connects to the OUT of the DSX respectively DS3/EC-1 cable options are listed in Table 3-4, “DS3/EC-1 cable assemblies” (p. 3-17). DS3/EC-1 transmission connections are in Table 3-5, “Twenty-four cable DS3/EC-1 transmission connections” (p. 3-24) and Table 3-6, “Twelve cable DS3/EC-1 transmission connections” (p. 3-28). Total of two function groups fully cabled will have 96 DS3 drop capacity. Note: The 96 DS3 figure does not include the 3 DS3 drops available when using the LNW39/LNW391 16/DS1/3/DS3 combo card in slot A/B. Instructions for cabling slot A/B are provided in “DS1 and DS3 hybrid cable installation” (p. 3-30). 7 1 (53) B8/B7 V/S 3/24 2 (54) 3 (55) 4 (56) B6/B5 B4/B3 B2/B1 W/BL¹ W/O¹ W/G¹ 2/23 44/43 1/22 Notes: 1. Some wire colors are used twice. White binder cables are for Channel 1 through 25 or Channel 29 through 53 and blue binder cables are for Channels 26, 27 and 28 or Channels 54, 55 and 56 are shaded. DSX-1 connections Alcatel-Lucent 1665 DMXtend backplane connections G r o u p ChanD S1 T/R term T/R color 62-Pin conn. pin# T/R Function group D conn. Function group G conn. In Out In Out

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Steps ................................................................................................................................................ 1 See the engineering job specification. Obtain the DS3/EC-1 cables per Table 3-4, “DS3/EC-1 cable assemblies” (p. 3-17) and note the function group where each cable will be used. Label the cables, indicating bay, shelf, function group (D or G) and direction (IN or OUT of the bay) at each end. Note: The first 12/24 ports of a function unit must be cabled to the right side connectors (J1D, J3D, J7G, and J9G), the additional DS3/EC-1 capacity ports (25 - 48) are cabled to the center connectors of the shelf (J2D, J4D, J8G, and J10G). ................................................................................................................................................ 2 Connect the function group cables at the Alcatel-Lucent 1665 DMXtend end, carefully matching the correct connector with the appropriate backplane connectors as shown in Figure 3-5, “DS3/EC-1 cable connections” (p. 3-15). Note: DS3/EC-1 and TMUX cable retaining screws must be tightened to a maximum of 6.5 in-lb. Do not overtighten. Note: The 12 conductor DS3/EC-1 cables that support the LNW16 12DS3/EC-1 pack connect only to the right side connectors (J1D, J3D, J7G, and J9G). The connectors in the center of the backplane (J2D, J4D, J8G, and J10G) are not used with the LNW16. See Table 3-4, “DS3/EC-1 cable assemblies” (p. 3-17) for more information. Note: The first 12/24 DS3/EC-1s of a Function Group must be connected to the right side connectors (J1D, J3D, J7G, and J9G). See Figure 3-6, “DS3/EC-1 cable routing to the right” (p. 3-15). The additional capacity of 24 DS3/EC-1s of the Function Group use the connectors located to the center of the backplane (J2D, J4D, J8G, and J10G). Note: The 24 conductor DS3/EC-1 cables that connect to the right side connectors (J1D, J3D, J7G, and J9G) are different from the 24 cable DS3/EC-1 cables that connect to the connectors in the center of the backplane (J2D, J4D, J8G, and J10G). See Table 3-4, “DS3/EC-1 cable assemblies” (p. 3-17) for more information. Function group Associated connector (DS3/EC-1) G G IN (J7G and J8G) G OUT (J9G and J10G) D D IN (J1D and J2D) D OUT (J3D and J4D)

R10.0 365-372-327R10.0 Issue 1 January 2013 3-15 ........................................................................................................................................................................ Cable and fiber installation Figure 3-5 DS3/EC-1 cable connections ................................................................................................................................................ 3 Route the cables along the backplane and out of the bay to the DSX per Figure 3-6, “DS3/EC-1 cable routing to the right” (p. 3-15). Figure 3-6 DS3/EC-1 cable routing to the right Notes: The 12-conductor DS3/EC-1 cable is showing that this cable could be either the 12- or 24-conductor DS3/EC-1 cable. Ports

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Figure 3-7 DS3/EC-1 cable routing to the left Notes: The 12-conductor DS3/EC-1 cable is shown. ................................................................................................................................................ 4 Route the cables along the cable rack and into the terminating bay (DSX or other terminating transmission equipment). ................................................................................................................................................ 5 Cut the cables to desired length and install the BNC connectors shipped with the cable assemblies. Note: When installing BNC connectors, follow the manufacturer’s instruction carefully to ensure a proper connection. Failure to do so may result in faulty DS3/EC- 1 signals as a result of improperly installed BNC connectors. ................................................................................................................................................ 6 Connect the cables to their respective positions on the terminating equipment.See Table 3-5, “Twenty-four cable DS3/EC-1 transmission connections” (p. 3-24) or Table 3-6, “Twelve cable DS3/EC-1 transmission connections” (p. 3-28) for DS3/EC-1 connections. Note: The 12-port cable and the 24-port cable use different signal grounds based on the circuit pack not the backplane. There is no issue interchanging these cables on the backplane. The DS3/EC-1 Signals are common between both cables. ................................................................................................................................................ 7 Check off the appropriate box in the Table I-2, Installation checklist.

R10.0 365-372-327R10.0 Issue 1 January 2013 3-17 ........................................................................................................................................................................ Cable and fiber installation Table 3-4 DS3/EC-1 cable assemblies Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections Function group D and G 12 Cable DS3/ EC-1 In (CA1) and 12 Cable DS3/EC-1 Out (CA2) Cable 849040787 10 849040795 20 849040803 30 849040811 40 849040829 50 849040837 60 849040845 100 849040852 150 849040860 250 849040878 450 Ne to Ne Only 849041751 450 735/734 Splice 849041769 750 735/734 Splice 849041777 900 735/734 Splice The following kits include 12 individually bagged BNCs with instructions plus one spare: KINGS 75ohm 735A cable type (12)BNC Plug Kit 848965778 KINGS 75ohm 734D cable type (12)BNC Plug Kit 848965786 TROMPETER 75ohm 735A cable type (12)BNC Plug Kit 848965794 TROMPETER 75ohm 734D cable type (12)BNC Plug Kit 848965802

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Right side cables for function group D and G 24 Cable DS3/EC-1 In (CA1) and 24 Cable DS3/EC-1 Out (CA2) Cable 848940011 10 These cables route to the right (as viewed from the rear of the shelf) and should be used with connectors J1D (IN), J3D (OUT) and J7G (IN), J9G (OUT) 848940029 20 848940037 30 848940045 40 848940052 50 848940060 60 848940078 70 848940086 80 848940094 90 848940102 100 848940110 110 848940128 120 848940136 140 848940144 150 848940151 160 Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 3-19 ........................................................................................................................................................................ Cable and fiber installation Right side cables for function group D and G 24 Cable DS3/EC-1 In (CA1) and 24 Cable DS3/EC-1 Out (CA2) Cable 848940169 180 848940177 200 848940185 250 848940193 300 Ne to Ne Only 848940201 400 Ne to Ne Only 848940219 450 Ne to Ne Only 848939856 250 735A/734 Splice 848939864 300 735A/734 Splice 848939872 300 735A/734 Splice 848939880 325 735A/734 Splice 848939898 350 735A/734 Splice 848939906 375 735A/734 Splice 848939914 400 735A/734 Splice 848939922 425 735A/734 Splice 848939930 450 735A/734 Splice 848939948 750 735A/734 Splice NE to NE 848939955 900 735A/734 Splice NE to NE Right side cables for function group D and G similar to above except no BNC’s are shipped loose. See below for different vendors’ BNC Plug Kits. 849041108 10 These cables route to the right (as viewed from the rear of the shelf) and should be used with connectors J1D (IN), J3D (OUT) and J7G (IN), J9G (OUT) 849041116 20 849041124 30 849041132 40 849041140 50 849041157 60 849041165 70 849041173 80 849041181 90 849041199 100 Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Right side cables for function group D and G BNC’s are shipped loose. See below for different vendors’ BNC Plug Kits. 849041207 110 These cables route to the right (as viewed from the rear of the shelf) and should be used with connectors J1D (IN), J3D (OUT) and J7G (IN), J9G (OUT) 849041215 120 849041223 140 849041231 150 849041249 160 849041256 180 849041264 200 849041272 250 849041280 300 Ne to Ne Only 849041298 400 Ne to Ne Only 849041306 450 Ne to Ne Only 849041892 250 735A/734 Splice 849041900 275 735A/734 Splice 849041926 300 735A/734 Splice 849041934 325 735A/734 Splice 849041942 350 735A/734 Splice 849041959 375 735A/734 Splice 849041967 400 735A/734 Splice 849041975 425 735A/734 Splice 849041983 450 735A/734 Splice 849041991 750 735A/734 Splice NE to NE 849042007 900 735A/734 Splice NE to NE These kits include 25/50 individually bagged BNCs w/ assembly instructions Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 3-21 ........................................................................................................................................................................ Cable and fiber installation KINGS 75ohm 735A cable type (24)BNC Plug Kit 848963062 KINGS 75ohm 734D cable type (24)BNC Plug Kit 848963070 TROMPETER 75ohm 735A cable type (24)BNC Plug Kit 848963088 TROMPETER 75ohm 734D cable type (24)BNC Plug Kit 848963096 ITT CANON 75ohm 735A cable type (24)BNC Plug Kit 409013554 ITT CANON 75ohm 734D cable type (24)BNC Plug Kit 409013588 ITT CANON 75ohm 735A cable type (50)BNC Plug Kit 409013562 ITT CANON 75ohm 734D cable type (50)BNC Plug Kit 409013570 Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Left side cables for function group D and G DS3 (24PK) Cable Assembly 849041788 250 735/734 Splice 849041793 275 735/734 Splice 849041801 300 735/734 Splice 849041819 325 735/734 Splice 849041827 350 735/734 Splice 849041835 375 735/734 Splice 849041843 400 735/734 Splice 849041850 425 735/734 Splice 849041868 450 735/734 Splice Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 3-23 ........................................................................................................................................................................ Cable and fiber installation Left side cables for function group D and G Similar to above except no BNC’s are shipped loose. See above for different vendors’ BNC Plug Kits 849040886 10 These cables route to the left (as viewed from the rear of the shelf) and should be used with connectors J2D (IN), J4D (OUT) and J8G (IN), J10G (OUT) 849040894 20 849040902 30 849040910 40 849040928 50 849040936 60 849040944 70 849040951 80 849040969 90 849040977 100 849040985 110 849040993 120 849041009 140 849041017 150 849041025 160 849041033 180 849041041 200 849041066 250 849041074 300 Ne to Ne Only 849041082 400 Ne to Ne Only 849041090 450 Ne to Ne Only 848932083 250 735A/734 Splice Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Table 3-5 Twenty-four cable DS3/EC-1 transmission connections Left side cables for function group D and G Similar to above except no BNC’s are shipped loose. See above for different vendors’ BNC Plug Kits 848932018 275 735A/734 Splice 848932026 300 735A/734 Splice 848932034 325 735A/734 Splice 848932042 350 735A/734 Splice 848932059 375 735A/734 Splice 848932067 400 735A/734 Splice 848932075 425 735A/734 Splice 848839528 450 735A/734 Splice Notes: 1. All the DS3/EC-1 cable assemblies can be used for either function group D or G. 2. Alcatel-Lucent 1665 DMXtend connectors J1D through J4D and J7G through J10G can be used for either DS1/E1 or DS3/EC-1 cabling. 3. Each Cable assembly # listed above contains two cable assemblies therefore a quantity of two per function group in the case of the 24 pair cables, must be ordered for the additional capacity. 4. For Input connections use cable CA1 (DS3/EC-1 IN) and for Output connections use cable CA2 (DS3/EC-1 OUT). 5. 735A cable is used to connect Alcatel-Lucent 1665 DMXtend to DSX-3 or another NE (10 to 450 ft. length). 6. The cable connectors are 62 pins D-Sub male-type connectors and fit into J1D through J4D and J7G through J10G. Coaxial cable Lead designation Name Connector pin# Connectors J1D (IN), J3D (OUT) and J7G (IN), J9G (OUT) This cable routes to the right. (Ports 1 - 24) Description Cable assembly # Cable length (feet) Alcatel-Lucent 1665 DMXtend backplane connections

R10.0 365-372-327R10.0 Issue 1 January 2013 3-25 ........................................................................................................................................................................ Cable and fiber installation 1 DS3 1R/1T Signal 40 FRG1 Ground 19 2 DS3 2R/2T Signal 17 FRG2 Ground 38 3 DS3 3R/3T Signal 57 FRG3 Ground 58 4 DS3 4R/4T Signal 13 FRG4 Ground 34 5 DS3 5R/5T Signal 53 FRG5 Ground 54 6 DS3 6R/6T Signal 10 FRG6 Ground 31 7 DS3 7R/7T Signal 51 FRG7 Ground 52 8 DS3 8R/8T Signal 6 FRG8 Ground 27 9 DS3 9R/9T Signal 47 FRG9 Ground 48 10 DS3 10R/10T Signal 4 FRG10 Ground 25 11 DS3 11R/11T Signal 24 FRG11 Ground 3 12 DS3 12R/12T Signal 1 FRG12 Ground 22 13 DS3 13R/12T Signal 59 FRG13 Ground 60 14 DS3 14R/12T Signal 16 FRG14 Ground 37 Coaxial cable Lead designation Name Connector pin#

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation 15 DS3 15R/12T Signal 36 FRG15 Ground 15 16 DS3 16R/12T Signal 55 FRG16 Ground 56 17 DS3 17R/12T Signal 12 FRG17 Ground 33 18 DS3 18R/12T Signal 32 FRG18 Ground 11 19 DS3 19R/12T Signal 9 FRG19 Ground 30 20 DS3 20R/12T Signal 49 FRG20 Ground 50 21 DS3 21R/12T Signal 28 FRG21 Ground 7 22 DS3 22R/12T Signal 5 FRG22 Ground 26 23 DS3 23R/12T Signal 45 FRG23 Ground 46 24 DS3 24R/12T Signal 43 FRG24 Ground 44 Connectors J2D (IN), J4D (OUT) and J8G (IN), J10G (OUT) This Cable Routes to the Left. (Ports 25 - 48) 25 DS3 25R/12T Signal 40 FRG25 Ground 19 26 DS3 26R/12T Signal 17 FRG26 Ground 38 27 DS3 27R/12T Signal 57 FRG27 Ground 58 Coaxial cable Lead designation Name Connector pin#

R10.0 365-372-327R10.0 Issue 1 January 2013 3-27 ........................................................................................................................................................................ Cable and fiber installation 28 DS3 28R/12T Signal 13 FRG28 Ground 34 29 DS3 29R/12T Signal 53 FRG29 Ground 54 30 DS3 30R/12T Signal 10 FRG30 Ground 31 31 DS3 31R/12T Signal 51 FRG31 Ground 52 32 DS3 32R/12T Signal 6 FRG32 Ground 27 33 DS3 33R/12T Signal 47 FRG33 Ground 48 34 DS3 34R/12T Signal 4 FRG34 Ground 25 35 DS3 35R/12T Signal 24 FRG35 Ground 3 36 DS3 36R/12T Signal 1 FRG36 Ground 22 37 DS3 37R/12T Signal 59 FRG37 Ground 60 38 DS3 38R/12T Signal 16 FRG38 Ground 37 39 DS3 39R/12T Signal 36 FRG39 Ground 15 40 DS3 40R/12T Signal 55 FRG40 Ground 56 41 DS3 41R/12T Signal 12 FRG41 Ground 33 Coaxial cable Lead designation Name Connector pin#

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Table 3-6 Twelve cable DS3/EC-1 transmission connections 42 DS3 42R/12T Signal 32 FRG42 Ground 11 43 DS3 43R/12T Signal 9 FRG43 Ground 30 44 DS3 44R/12T Signal 49 FRG44 Ground 50 45 DS3 45R/12T Signal 28 FRG45 Ground 7 46 DS3 46R/12T Signal 5 FRG46 Ground 26 47 DS3 47R/12T Signal 45 FRG47 Ground 46 48 DS3 48R/12T Signal 43 FRG48 Ground 44 Notes: 1. Lead designation for EC1 connection for cable# x should be read as EC1 xR/xT instead of DS3 xR/xT, where x is a number from 1 to 48. Coaxial cable Lead designation Name Connector pin# Connectors J1D (IN), J3D (OUT) and J7G (IN), J9G (OUT) This Cable Routes to the Right. (Ports 1 - 12) 1 DS3 1R/1T Signal 40 FRG1 Ground 39 2 DS3 2R/2T Signal 17 FRG2 Ground 18 3 DS3 3R/3T Signal 57 FRG3 Ground 58 Coaxial cable Lead designation Name Connector pin#

R10.0 365-372-327R10.0 Issue 1 January 2013 3-29 ........................................................................................................................................................................ Cable and fiber installation 4 DS3 4R/4T Signal 13 FRG4 Ground 14 5 DS3 5R/5T Signal 53 FRG5 Ground 54 6 DS3 6R/6T Signal 10 FRG6 Ground 11 7 DS3 7R/7T Signal 51 FRG8 Ground 50 8 DS3 8R/8T Signal 6 FRG8 Ground 7 9 DS3 9R/9T Signal 47 FRG9 Ground 46 10 DS3 10R/10T Signal 4 FRG10 Ground 3 11 DS3 11R/11T Signal 24 FRG11 Ground 23 12 DS3 12R/12T Signal 1 FRG12 Ground 2 Note: Lead designation for EC-1 connection for cable# x should be read as EC1 xR/xT instead of DS3 xR/xT, where x is a number from 1 to 12. Coaxial cable Lead designation Name Connector pin#

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation DS1 and DS3 hybrid cable installation Description This section describes how to connect the DS1 and DS3 Hybrid cables to the Alcatel- Lucent 1665 DMXtend shelf and route the cables out of the bay and to the DS1 and DS3 Hybrid Cable terminating equipment. Perform this procedure if DS1 and DS3 Hybrid cables are required. Note: When cabling the Alcatel-Lucent 1665 DMXtend to a DSX, the DSX becomes an extension of the Alcatel-Lucent 1665 DMXtend backplane connections. Therefore, the IN on the Alcatel-Lucent 1665 DMXtend backplane connects to the IN of the DSX and the OUT of the Alcatel-Lucent 1665 DMXtend backplane connects to the OUT of the DSX respectively DS1 and DS3 Hybrid cable options are listed in Table 3-7, “DS1 and DS3 hybrid cable assemblies” (p. 3-33). DS1 and DS3 Hybrid Cable transmission connections are in Table 3-9, “DS1 and DS3 hybrid cable DS1 transmission connections” (p. 3-35). Steps ................................................................................................................................................ 8 See the engineering job specification. Obtain the DS1 and DS3 Hybrid cables per Table 3-7, “DS1 and DS3 hybrid cable assemblies” (p. 3-33) and note the function group where each cable will be used. Label the cables, indicating bay, shelf, function group (A and B) and direction (IN or OUT of the bay) at each end. ................................................................................................................................................ 9 Connect the function group A/B cables at the Alcatel-Lucent 1665 DMXtend end, carefully matching the correct connector with the appropriate backplane connectors as shown in Figure 3-8, “DS1 and DS3 hybrid cable connections” (p. 3-31). Note: The DS1 and DS3 cable retaining screws must be tightened to a maximum of 6.5 in-lb. Do not overtighten. Note: The DS1 and DS3 Hybrid Cable only supports slots A1/B1 and A2/B2 and only connects to J5A/B (IN) and J6A/B (OUT).

R10.0 365-372-327R10.0 Issue 1 January 2013 3-31 ........................................................................................................................................................................ Cable and fiber installation Figure 3-8 DS1 and DS3 hybrid cable connections ................................................................................................................................................ 10 Route the cables along the backplane and out of the bay to the DSX per Figure 3-9, “DS1 and DS3 hybrid cable routing” (p. 3-31). Figure 3-9 DS1 and DS3 hybrid cable routing ................................................................................................................................................ 11 Route the DS1 cables along the cable rack and into the terminating bay (DSX-1 or other terminating transmission equipment), and route the DS3 cables along the cable rack and into the terminating bay (DSX-3 or other terminating transmission equipment). ................................................................................................................................................ 12 Cut the coaxial cables to desired length and install the BNC connectors shipped with the cable assemblies.

R10.0 365-372-327R10.0 Issue 1 January 2013 ........................................................................................................................................................................ Cable and fiber installation Note: When installing BNC connectors, follow the manufacturer’s instruction carefully to ensure a proper connection. Failure to do so may result in faulty DS3 signals as a result of improperly installed BNC connectors. ................................................................................................................................................ 13 Referring to Table 3-8, “DS1 and DS3 hybrid cable DS3 transmission connections” (p. 3-35) connect the cables to their respective positions on the terminating equipment or DSX. ................................................................................................................................................ 14 Remove slack and cut the DS1 cables to the desired length at the DSX. ................................................................................................................................................ 15 Referring to Table 3-9, “DS1 and DS3 hybrid cable DS1 transmission connections” (p. 3-35), carefully observe color codes and wire-wrap the cables at the DSX. ................................................................................................................................................ 16 Check off the appropriate box in the Table I-2, Installation checklist. ........................................................................................................................................................ E N D O F S T E P S