Bellman BE1033 Quick Start Manual

Visit portable receiver Volume Power LED Flash signal switch Recessions for wall bracket Battery compartment Optional power supply BE1270 Bed shaker Test button BE1450 Flash LEDs BE1033 In the box � BE1033 Portable receiver � 4�1.5V LR14 batteries � Wall bracket � Screws and wall plugs Power and battery � Mains power 7.5 V DC / 1000 mA Optional power supply unit Europe: BE9275+BE9268 UK: BE9268+BE9276 � Battery power 4�1.5 V LR14 alkaline batteries � Operating time 2 – 3 years with alkaline batteries � Power consumption Active: 1000 mA Idle position: 0.1 mA Output � Adjustable sound signal Max 93 dBA @ 1 m, frequency range: 500 – 1000 Hz � Bed shaker outlet: 2.0 – 4.0 VDC or Speaker outlet: 10 kΩ, 0 – 4 V Frequency and coverage � Radio frequency 314.91 MHz, 433.92 MHz or 868.30 MHz, depending on the region � Coverage 50 – 250 m, 55 - 273 yd. depending on the radio frequency and the characteristics of the building Accessories � BE1270 Bed shaker � Power supply unit, Europe: BE9275+BE9268 UK: BE9268+BE9276 Dimensions and weight � Height: 165 mm, 6.5" � Width: 130 mm, 5.1" � Depth: 36 mm, 1.5" � Weight: 590 g, 20.8 oz. incl. batteries Technical specifications

Place the receiver on a level surface or mount it on the wall using the wall bracket. 2 To test the radio link you need a Visit transmitter. Press the test button/s on the transmitter. 3 The receiver starts to flash and sound. If a bed shaker is connected, it will vibrate. A short press on the test button repeats the last indication. If nothing happens, see Troubleshooting. Default signal pattern When a transmitter is activated, the receiver lights up an LED, sounds, flashes and the bed shaker starts to vibrate with a certain pace. This is called signal pattern. The transmitters determine the pattern, and the default is as follows: Transmitter Portable receiver Bed shaker Activated source Visit LED Sound Flash Vibration � Door transmitter / push button transmitter Green Door chime Yes Slow � Telephone transmitter Yellow Ring signal Yes Medium � Baby monitor Orange Baby melody Yes Fast � Smoke alarm Red Fire horn Yes Long Changing the signal pattern The signal pattern can only be changed on the transmitters. See Changing the signal pattern for the relevant transmitter. Adjusting the volume and flash Adjust the volume to your liking using the red volume dial on the top of the receiver. It goes from 0 to 93 dBA @ 1 m with a main frequency range of 500 – 1000 Hz. Use the flash signal switch on the back of the receiver to turn the flash off/on. Replacing batteries If the power LED is yellow when the receiver is activated, the batteries are nearly depleted. Here is how you replace them: � Slide open the battery cover. Replace the old batteries with four new 1.5 V LR14 alkaline batteries, see the battery compartment for correct positioning. Visit portable receiver

If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio interference, you need to change the radio key on all units. The radio key switches are located on the transmitters. Here is how you change the radio key: 1 Open the transmitter cover and move any radio key switch to the up (on position) to change the radio key. See Changing the radio key for the relevant transmitter. 2 Press and hold the test button located on the bottom of the portable receiver until the green and red Visit LEDs blink alternately. Release the button. 3 Press the test button/s on the transmitter within 30 seconds to send the new radio key. 4 The power LED lights up orange and green, and the flash LED flashes red to show that the radio key has been changed. It then returns to normal mode. 1 2 3 4 Visit portable receiver BE1270 On Off Accessories The portable receiver can be complemented with the following accessories: � BE1270 Bed shaker Wakes you with vibrations if anything happens while you are asleep. Connect it to the receiver and slide it under your pillow or mattress. � BE9275 + BE9268 EU / BE9268 + BE9276 UK power supply If your receiver has a fixed place, you can connect it to mains power and not having to worry about batteries. Note: All Visit units must be set to the same radio key in order to operate as a group.

� The batteries are depleted. Replace them with 4�1.5V LR14 alkaline batteries. The power LED is orange when the receiver is activated. � The battery level is low. Replace them with 4�1.5V LR14 alkaline batteries. The receiver does not respond when a transmitter is activated, but works when I use the test button � Check the transmitter batteries and connections. � Move the receiver closer to the transmitter to make sure it’s within radio range. � Check that the receiver is set to the same radio key as the other units in the Visit system, see Changing the radio key. The receiver is activated for no apparent reason � There is probably another Visit system installed nearby that triggers your system. Change the radio key on all units, see Changing the radio key. The receiver is too quiet � Turn up the volume using the red volume dial on the top of the unit. The receiver is not flashing � Check that the flash signal switch on the back of the unit is set to the ON position. Troubleshooting Visit portable receiver Learn more at wom.com.au Phone 1800 966 266