Edgewater Networks 4610W Quick Start Manual

Before You Start Please read this guide thoroughly as it describes the basic installation of the device. Additional configuration needed to deploy the device in a specific environment can be performed with the help of online help. This guide also provides an example of a typical 4610W device deployment that can be used as a guideline for your installation. Requirements for Installation • A computer with a web browser such as Microsoft Internet Explorer or Netscape Navigator or any other browser of your choice • At least one Ethernet cable • Following information supplied by the VoIP Service Provider o IP address of the WAN interface o if T1 is being used for WAN connection then: � T1 frame format � Layer 2 protocol such as PPP, Frame Relay/DLCIs, HDLC, etc. o IP address of the Softswitch

Instructions Step 1 � Connecting the Cables Figure 1: 4610W Front Panel 1. Connect one end of an Ethernet cable to local LAN port 24 of the 4610W device. This port can be seen in the area “C” of the above diagram. Connect the other end of the cable to your computer’s Ethernet port. 2. If T1 is used for the WAN connectivity then perform the following steps, otherwise go to step 5. 3. Based on the number of functional ports, connect on end of the T1 cable(s) to the T1 port(s) and the other end of the cable(s) to the T1 demarcation unit provided by the Service Provider. The T1 port(s) are located in area “E” of Figure 1. To reduce the risk of fire, connect the T1 port to the T1 network using only 26 AWG or larger wire such as 24, 22, 20, etc. 4. Skip to step 6. 5. Connect an Ethernet cable between the Ethernet WAN port of the 4610W device, shown in the above diagram as “D,” and the Ethernet port on a router or a modem. 6. Connect the PSTN lines to ports denoted by “F” or “G” in the above diagram. 7. Connect the regular phones or key system to ports denoted by “G” in the above diagram.

8. Plug one end of the power adapter into an AC outlet and the other end into the power receptacle of the 4610W device (shown below as “B” in Figure 2). Make sure that the power and status LEDs (shown above as Figure 1 as “A” and “B”) are solid green after a short while. A B Figure 2: 4610W Back Panel

Step 2 � Configuring the EdgeMarc 1. The EdgeMarc device comes preconfigured with 192.168.1.1 local LAN address with a subnet mask of 255.255.255.0. So configure your computers Ethernet adapter’s IP address to any address other than 192.168.1.1 in the same subnet mask, for example 192.168.1.10. If using a LAN switch then the switch must support 100Mbps full duplex. 2. Launch a web browser on the PC and enter the following URL: http://192.168.1.1 and hit enter 3. The following login window should appear: 4. Enter “root” in the “User name” field and “default” in the “Password” field. 5. The “System” page should appear next. 6. From the “Configuration Menu” on the left configure the following: • “Network” – To configure WAN and LAN ports • Optionally configure “DHCP Server” to suit your needs.

Step 3 � Plan Your Configuration The EdgeMarc 4610W Network Services Gateway can be deployed as a gateway router in a network. It can also be deployed in a network behind an existing firewall. Based on your deployment criteria, consult the VoIP Operating System (VOS) for EdgeMarc User Manual for further configuration: Helpful Hints Although not recommended, the 4610W device and IP phones can be installed behind an existing enterprise firewall. In this instance the firewall will have to be configured to allow access to and from the 4610W device’s public IP address for the following ports: Port Type Firewall Ports to Open UDP 161 (SNMP) and 162 (SNMPTRAP) UDP 16386 - 17286 TCP SSH TCP 22 for remote management & TCP 80 for WAN configuration-downloads Telnet 23 FTP TCP 21 for stateful TCP-session control from the 4610W to Edgewater FTP server MGCP 2427, 2429, 2432, and 2727 NTP ¬ 123 SIP 5060 and 5075 IP phones normally point to a local NTP server for their time reference. The NTP port 123 needs to be opened if your network does not have an NTP server. Please Note: Traffic shaping for this configuration is only available if the enterprise data devices are also installed behind the 4610W device.

The web page configurations for the various 4610W device deployments are shown below. The two darker-shaded rows indicate the minimum configuration required for each deployment. 4610W Device GUI Configuration Page 4610W Device as Gateway Router 4610W Device within existing infrastructure 4610W Device behind an existing firewall Network Yes Yes Yes VoIP/ALG Yes Yes Yes NAT Yes Optional Yes Firewall Yes Optional, but recommended Optional, but recommended DHCP Yes Yes (but should be disabled if DHCP server already exists) Yes (but should be disabled if DHCP server already exists) Traffic Shaper Yes Yes Optional (depends on network topology) Traffic Simulator Only for testing Only for testing Only for testing System As needed As needed As needed Please visit our website at www.edgewaternetworks.com or contact the Edgewater Technical Assistance Center at 408.351.7255 for additional information or assistance. Edgewater Networks, Inc. 2895 Northwestern Parkway Santa Clara, CA 95051 Phone: (408) 351-7200 [email protected] Copyright© 2010, Edgewater Networks, Inc. All rights reserved. Converged Networking. Simplified.