BCN3D Sigma Series Quick Start Manual

Watch our video to see how to correctly position the printing surface. Set up video We would like to thank all users for trusting BCN3D, for helping us to reach our dreams and to create a better product every day. 1. Unboxing 1. Open the box from the top. 2. Remove the components from the foam and place them on a table. Then remove the foam and the cardboard. 3. Remove the lateral foam protections. 4. Lift the printer with care holding it from the side flanges and place it on the table. 5. Open the plastic bag containing the printer. Quick Start Guide BCN3D Sigma Series Proper area to take out the printer with your hands. 2. Set up Remove protections • Remove all the protection foams inside the printer. There are three on the carriage and one under the printing surface. • Pivot the left and right spring clips away from the aluminium platform. • Take the glass printing surface from the upper protective foam. • Place the glass printing surface on top of the aluminium platform. • Insert the glass with light force into the back spring clips. • Fix it with the left and right spring clips. Install printing surface For more detailed information about the processes shown in this guide, read the User Guide. User Guide in your own language Unboxing Watch our video to see how to correctly unbox. Unboxing video Retain packaging for warranty service. The printer is heavy and therefore this step needs to be performed by two people. Make sure that the table where the printer is being installed, is close enough. The glass printing surface must be handled with care. In case of breakage, it may cause injuries. Specifications subject to change. EN-MSS-2020-v1 Install plastic covers • Take the plastic covers and thumbscrews from the packaging. • Peel off the protective films. • Use the thumbscrews to install the plastic covers.

problem in this manual, please contact the BCN3D technical support team through Contact Support. Turn on the printer • Take the power supply cable out from the accessories box that was on top of the printer. • Connect the power supply cable to the power socket at the back of the printer. • Plug the other end of the cable into a wall outlet. • Turn the printer on. The power switch is found on the left side of the printer. Getting started Scan the QR code to be guided through the Setup Assistant for network connectivity, loading filament and calibrating your printer. What is in the box? • BCN3D Sigma Series with 0.4mm hotends • Glass printing surface • 2 PLA spools • 2 Spool holders • Quick start guide • SD card • Ethernet cable • USB cable • Spatula • 3 Allen key • Pliers • 10 Hotend Shims • USB Wifi dongle • Power supply cable • Nylon cleaning filament • Calibration gauge • Magigoo glue stick • Sample part • 3 plastic covers • 10 Thumbscrews 1 If you have the option, we recommend using the printer with an Ethernet connection as it is more stable than Wifi. Information Online Ethernet • Take the ethernet cable out from accessories box. • Connect the ethernet cable to the ethernet port at the back of the printer. • Connect the other end of the cable to a network source. Wifi • Find the USB WiFi Dongle in the accessories box. • Plug the USB WiFi Dongle into the USB port at the back of the printer. Offline SD Card • Find the SD Card in the tool box, inside the upper box. • Insert the SD Card into the SD Card slot at the front of the printer. 3. Using the printer 1. Hotend 2. Bowden tube 3. Purge tank 4. SD Card reader 5. Touchscreen 6. Spool holder 7. Filament spool 8. Glass printing surface 9. Extruder 10. Power plug 11. USB port 12. Ethernet port 13. External spool holder 14. External filament spool 15. Filament Runout sensor (FRS) 16. Power switch 5 4 9 12 3 8 1 Diagram The BCN3D Sigma Series can be used online or offline. However connecting the printer to the network is needed in order to register it and to use the BCN3D Cloud functionality.1 Specifications subject to change. EN-MSS-2020-v1 14 2 16 11 6 7 13 Setup Assistant Watch our video to see how to run the Setup Assistant Getting started 10 15