C.A. Technologies Panther 200C Product Information

MODEL NO. AIR CAPS Press / Siphon *SUGGESTED GUN INLET PRESS. FAN CONTROL SCFM AIR CAP RING AVAILABLE FLUID NOZZLES NEEDLES / marking on needle 22-2030 siphon 50 12 22-2058 p & s 40 6 32-0611 1.1mm (.042") 40-1211 (211) 22-2080 siphon 60 14 32-0614 1.4mm (.055") 40-1214 (214) 22-2062** pressure 80 19 32-0618 1.8mm (.070") 40-1218 (218) 22-2064** pressure 80 22 32-0618V 1.8mm (.070") 40-5301 22-2704 pressure 70 21 32-0818 1.8mm (.070") 22-2765 pressure 80 22 32-0622 2.2mm (.086") 22-2777 pressure 70 23 32-0622V 2.2mm (.086") 40-5301 22-2797 pressure 70 21 32-0628 2.8mm (.110") 40-1228 (228) 22-2880 siphon 60 15 included 32-0628V 2.8mm (.110") 40-5301 22-2900 siphon 45 12 22-1001 Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4) *Gun inlet pressures may vary as required by application **Air caps available with teflon coating (22-2062T & 22-2064T) 40-1222 (222) P200C 60-1500 included 22-1001 Panther 200C Panther 200C Panther 200C Panther 200C Panther 200C PRESSURE/SIPHON FEED SPRAY GUN PRODUCT INFORMATION Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708 www.spraycat.com

PP PP200C 200C 200C 200C 200C Spray Guns Operation 1. Connect air supply hose at handle of gun. 2. Connect a pressurized fluid supply or paint siphon cup to the gun fluid inlet. 3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”. 4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan. Maintenance IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation. Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner. 1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures instructions. 2. If a gun cleaner is not being used: Remove air cap and clean separately using clean solvent. For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow thru the gun until clean. For siphon setups, first clean the siphon cup thoroughly then spray clean solvent thru the gun until clean. NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance. Gun head disassembly and reassembly instructions: Have repair kit # 10-110 available before gun disassembly. Gun head disassembly To remove the nozzle carrier (5) and air cap adapter (6): 1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (13). 2. Remove the needle seal cartridge (23). 3. Loosen the locknut (9) and remove fluid inlet (10) using a 5/8” open-end wrench. 4. The nozzle carrier (5) and air cap adapter (6) will now slide forward from the gun body (11). Gun head reassembly 1. Install a new o-ring (7) on the air cap adapter (6). 2. Install o-ring (4) between fluid nozzle body (3) and fluid nozzle carrier (5). 3. Install the thread locknut (9) onto the fluid inlet (10) as far as possible. 4. Install a new fluid inlet seal (8) into the recess area on the nozzle carrier (5) inlet port. 5. Slide the nozzle carrier (5) into air cap adapter (6) and insert into the gun body (11) as far as possible. Be sure the nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (23) but do not tighten. 6. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the body. While in this position, insert the fluid inlet (10) and tighten firmly. 7. Tighten the needle seal (23) to approx. 12 ft.-lb. torque. 8. Tighten the fluid inlet (10) to approx. 25 ft.-lb. torque. 9. Tighten the locknut (9) to approx. 33 ft.-lb. torque.

Air Cap** 16 60-206 Needle Return Spring (HD)* 2 See Air Cap Chart Fluid Nozzle Tip** 17 60-201 Rear Bushing 3 32-2201 Fluid Nozzle Body 18 60-119 Seal* 4 98-8020 Gasket* 19 60-1520 Air Valve Assembly 5 60-L21C Nozzle Carrier 20 60-302 Air Valve Poppet 6 60-22 Air Cap Adapter 21 60-125 O-Ring* 7 60-131 O-Ring* 22 61-1003 Air Valve Spring* 8 60-124 Fluid Inlet Seal 23 60-1400 Needle Seal Cartridge* 9 60-128 Locknut 24 60-2101 Trigger 10 60-126 Fluid Inlet Fitting 25 60-1510 Air Control 11 60-1125 Panther Gun Body Conventional 25A 60-122 Plug (optional) 12 See Air Cap Chart Fan Control Assembly** 26 60-104 Air Inlet Fitting 13 See Air Cap Chart Fluid Needle** 27 60-1033 Trigger Pivot Set 14 60-202 Fluid Control Knob 28 98-0109 Allen Plug 15 60-209 Spring Seat* **See air cap selection chart on page 1 *Indicates part included in repair kit # 10-110 * * * * * * * * *

MATERIAL TYPE FLUID ORIFICE x AIR CAP MAXIMUM PATTERN WIDTH PRESS. / SIPHON Very Thin less than 16 sec. Zahn #2 inks , dyes, solvents, stains Thin 16 to 20 sec. Zahn #2 lacquers, enamels, primers, sealers Medium 21 to 30 sec. Zahn #2 automotive base coat enamels, primers epoxies, urethanes automotive clear coat Heavy over 30 sec. Zahn #2 heavy body primers high solid enamels high solid automotive coatings adhesives FLUID NOZZLE / AIR CAP SELECTION CHARTS PANTHER Series 200C - Pressure / Siphon Feed Guns 1.1 mm x 2058 1.1 mm x 2030 9 10 P/S S 1.8mm x 2765 1.8mm x 2797 2.2 mm x 2880 2.2 mm x 2064 15 17 13 14 P P S P 1.1, 1.4 mm x 2058 1.1, 1.4 mm x 2030 1.1, 1.4 mm x 2900 9 10 10 P/S S S 1.4, 1.8 mm x 2080 1.4, 1.8 mm x 2704 1.4, 1.8 mm x 2765 1.4, 1.8 mm x 2777 1.4, 1.8 mm x 2797 1.4, 1.8 mm x 2900 13 12 15 14 17 10 S P P P P S Revised 3/18/14