Steelcase Opus Manual 

If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500) Or visit our website: www.steelcase.com © 2014 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Printed in U.S.A. ® Page 1 of 12 939500290 Rev C

939500290 Rev C NOTE: Determine which base unit will have the side panel attached. 1. Turn base assembly on it's side. Lower the end panel onto the base assembly as shown (1a). Make sure there is a 1/8" offset at the top of the base assembly and make sure the front of the end panel is 3/4" from the front of the canopy (1b). The bottom of the end panel will be flush with the top of the base. 2. Secure the end panel to the base assembly by first squaring up the top of the panel to the top of the base assembly and installing three (3) 1-1/4" wood screws (2a). NOTE: When squaring up top of panel to top of assembly, be mindful of the 1/8" offset discussed in step 1. Square up the back of the end panel to the back edge of the base assembly and install the five (5) remaining 1-1/4" screws (2b). 2b 2a 1b 1a INSTALL THESE FIVE (5) 1-1/4" WOOD SCREWS ONE AT A TIME BY FIRST SQUARING UP BACK OF PANEL TO BACK OF ASSEMBLY INSTALL THESE THREE (3) 1-1/4" WOOD SCREWS FIRST AFTER SQUARING UP TOP OF PANEL TO TOP OF ASSEMBLY 19-5/16" REF. END PANEL 3.4” 1/8” OFFSET

939500290 Rev C 3. Align gussets at end of toeboard (3a) and secure using four (4) 5/8" wood screws (3b). Align toeboard with toeboard side and gussets (3c). Attach toeboard with four (4) 5/8" wood screws though gussets and into toeboard (3d). 4. Align toeboard face flush with base as shown (4a) and attach using three (3) 1-1/4" wood screws (4b). 3a 4a 4b 3b 3d 3c FLUSH FLUSH THREE (3) 1-1/4" WOOD SCREWS GUSSETS TOEBOARD SIDE TOEBOARD FOUR (4) 5/8" WOOD SCREWS FOUR (4) 5/8" WOOD SCREWS

939500290 Rev C 5. Push base unit into place. 6. Level base unit. 7. Secure units together and place in position against wall. Refer to assembly direction #939500801. 8. Install storage cabinet. Refer to assembly direction #939500811. 5 6 BASE UNIT

939500290 Rev C 9. Secure end panel to lower storage cabinet using two (2) 1-1/4" wood screws. 10. Insert (5) shoulder screws into the holes on the filler panel. 9 10 TWO (2) 1-1/4" WOOD SCREWS SHOULDER SCREWS FILLER PANEL

939500290 Rev C 11. Align filler panel with end panel (11a) and insert the shoulder screws into the modeeze clips (11b) located on the front of the end panel. Push the panel downward (11c), until shoulder screw is securely seated (11d). 11a 11b 11c 11d

939500290 Rev C 12. Turn the other base assembly on it's side. Lower the end panel onto the base assembly as shown (12a). Make sure the top of the base assembly and the top of the end panel is flush (12b), also make sure the side of the end panel is flush with the front of the canopy assembly and square to the base unit upright (12c). 13. Secure the end panel to the base assembly by first squaring up the top of panel to the top of the assembly and installing three (3)1-1/4" wood screws (13a). Square up the back of the end panel to the back edge of the base assembly and install the six (6) remaining 1-1/4" screws (13b). 14. Install three (3) shelf support pins into the end panel. 14 12a 12b 12c 13a 13b INSTALL THESE (6) 1-1/4" WOOD SCREWS ONE AT A TIME BY FIRST SQUARING UP BACK OF PANEL TO BACK OF ASSEMBLY INSTALL THESE (3) 1-1/4" WOOD SCREWS FIRST AFTER SQUARING UP TOP OF PANEL TO TOP OF ASSEMBLY FLUSH FLUSH END PANEL 20-3/32" REF.

939500290 Rev C 15. Slide units together. Secure units together and place in position against wall. Refer to assembly direction #939500801. 16. Install storage cabinet. Refer to assembly direction #939500811. 17. Secure end panel to lower storage cabinet using two (2) 1-1/4" wood screws. 15 17 TWO (2) 1-1/4" WOOD SCREWS

939500290 Rev C 18. Slide the two units next to adjoining assembly (18a). Level base unit (18b). Attach using one (1) wood screw as shown (18c). 18b 18a 18c

939500290 Rev C 19. Determine a level line on corner wall and mark with pencil (19a). Attach dust cover attachment support using two (2) screws (19b). 19a 19b DUST COVER ATTACHMENT SUPPORT

939500290 Rev C 20. Determine the width of the dust cover (20a). Using a jig saw, cut the dust cover to width (20b). 21. Mark, with a pencil, a 3/4" x 7" corner of the dust cover as shown. Using a jig saw, cut dust cover according to the measurements. 20a CUT OUT AND REMOVE THIS PIECE PER MEASUREMENTS 7” 3/4” DUST COVER WIDTH MEASUREMENT 20b 21

939500290 Rev C 22. Lower dust cover into place (22a) and attach using three (3) 1-1/4" wood screws (22b). 22a DUST COVER 22B THREE (3) 1-1/4” WOOD SCREWS