Digimate DGL3704M Operation & User’s Manual

HANDLING YOUR DISPLAY, PLEASE BE AWARE ALL WARNINGS AND SAFETY PRECAUTIONS CONTAINED AS BELOW. Never Insert anything into DISPLAY!! ¾ Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. ¾ Never spill liquid of any kind on the Display。 Do not attempt to service the DISPLAY yourself!! ¾ Opening or removing covers may expose you to dangerous voltages and other hazards. Refer all servicing to qualified service personnel. Note: 1. Read all safety and operating instructions before operating your new Display. To ensure good ventilation, a distance of more than 10cm shall be maintained between the Display and any other furniture. 2. For this Display set, the operating temperature is 5 ~ 35 °C, storage temperature is 0 ~ 60 °C。 Do not touch your DISPLAY and antenna during thunderstorms!! Unplug the Display during thunderstorms or if it is not going to be used for an extended period. ¾ Failure to do so may result in electric shock or fire. ATTENTION!! ¾ Unplug the DISPLAY from the wall socket before cleaning. ¾ Use a damp cloth for cleaning. ¾ Do not use liquid or aerosol cleaners. Well ventilation is required!! To ensure reliable operation of the product and to protect it from overheating, the ventilation must not be blocked or covered. ¾ The monitor should be away from the wall 10 cm above, and always keep the vent clean. ¾ Do not place your DISPLAY in a cramped and inadequately ventilated place. ¾ Avoid your DISPLAY to be placed upside down in any time.

FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception (this can be determined by turning, the device off and on), you are encouraged to try to correct the interference by one or more of the following measures: *Reorient or relocate the receiving antenna. *Increase the separation between the equipment and the receiver. *Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. *Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, you should use the shielded signal cord and power cord supplied with this unit. The Federal Communication Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. CE MARKING DECLARATION OF CONFORMITY The LCD display complies with the requirements of related European standards, which include: z Emission: EN 55022, EN 61000-3-2, EN-61000-3-3 z Immunity: EN 50082-1 z Safety: EN 60950 Low-Voltage Directive (73/23/EEC) is a trademark of SRS Labs, Inc. WOW technology is incorporated under license from SRS Labs, Inc. manufactured under license from BBE Sound, Inc.

either as a Television or as a computer monitor. With its multiple input options, you can connect almost any device (e.g. VCR, DVD players and game consoles) to this display. You can also connect your display to a stereo system with a subwoofer to experience the ultimate in home entertainment. This Manual has been designed to help you install and operate your display properly. We would recommend that you read it thoroughly. Table of contents Page Getting Started Features..…………………………………………………………. 4 Standard Accessories ………………………………................ 4 Controls and Function ……………………………… 5 Remote Control …………………………………………………. 7 Installation Installing your Display …………………………………………. 8 Quick Installation ……………………...……..……………….… 9 Operation - TV Basic Operation…………………………………………………... 10 OSD MENU Setting …………………….………………………… 11 TV/PC Parameters……..……...……………………………..….. 12 Audio Settings……………………………………………….…..... 13 Picture-In-Picture………..………………………………….…….. 14 General Settings………………………………………….……..… 15 Parental Controls …………………..…..………………….…….. 17 Other information Troubleshooting ………………………….…………………….... 20 Supporting Operation Mode ……………….…………………..… 21 Introduction Table of contents Table of contents

˙ Wide viewing angle ˙ Digital Character Smoothing ˙ Analog TV tuner ˙ Windows 95/98/2000/XP Plug & Play Compliant ˙ Versatile, functional & User friendly OSD ˙ Plug & Play: Conform to the VESA standards and support DDC 2B spec. SSStttaaannndddaaarrrddd AAAcccccceeessssssooorrriiieeesss Unpacking and Checking of the Package Contents y Before unpacking your LCD Display, prepare a stable, level, and clean surface near a wall outlet for your LCD Display. y Set the LCD Display box in an upright position and open from the top of the box before removing the right/left cushions. Accessories 1 pc 1 pc 1 pair 1 pc User’s Manual Remote Controller Batteries RCA Adapter 1 pc 1 pc 1 pc VGA Cable Power Cord Audio Cable Power source: (for 37” AU Panel) - Manufacturer: FSP - Type: FSP310-4M01 - Rating: 3.5A, AC 100-240V, 50-60Hz

Operating the monitor Top Panel Buttons： ① POWER：Press to turn the Display On/Off. (Main Power Switch must be On) NOTE: The Main Power Switch is located on lower back panel. ② SOURCE：Press to display and cycle the available input sources. ③ MENU：Press to open the OSD menu and make function changes/adjustments. ④ ENTER: Press to select an item, exit a function in the OSD menu or confirm a setting. ⑤,⑥ CHc/d： Press to select a channel or select items in OSD menu. ⑦,⑧ VOLf/e：Press to adjust the volume, select OSD items and adjust the menu items. • MAIN POWER SWITCH (Rear Panel): Set to on ( – ) to power up unit. Front View LED indicator Green for operating PC monitor and TV system. Red when AC Power switch on or no signal.

Side view 1 Y1Cb1Cr1 Video Component1 Input terminal accepts video signal from a Component Video Source (INTERLACED only) 2 Y1Cb1Cr1 Audio L&R Audio input corresponding with Video Component1 3 Y2Pb2Pr2 Video Component2 Input terminal accepts video signal from a Component Video Source (PROGRESSIVE SCAN or INTERLACED) 4 Y2Pb2Pr2 Audio L&R Audio input terminals corresponding with Video Component2 5 S-video S-Video Input terminal accepts video signal from a S-Video source. 6 S-video Audio L&R Audio input terminals corresponding with S-Video source. 7 Sub-woofer Provides a dedicated Sub output signal to drive an external Powered Subwoofer (optional) 8 Video out Provides a Video output signal. (Video output is available only from; AV1, AV2, AV3 and TV sources) 9 Audio out Provides a Stereo Audio output signal. (Audio output is available only from; AV1, AV2, AV3, TV sources) 10 AV 1 in To connect the AV1 Video source. 11 AV 1 audio in To connect the Audio corresponding to AV1 source 12 AV 2 in To connect the AV2 Video source. 13 AV 2 audio in To connect the Audio corresponding to AV2 source 14 AV 3 audio in To connect the Audio Corresponding to AV3 source 15 AV 3 in To connect the AV3 Video source. 16 Headphone Provides L&R Audio output to connect a set of headphones. Bottom view 1 PC Audio In Accepts the Audio signal from your PC or Laptop. 2 ANT Connect the coaxial cable (75 Ohm) or antenna here. 3 D-sub Connects to D-sub 15 pin analog RGB Video from your PC or Laptop. 4 DVI for PC Connects to DVI digital video output from your PC or Laptop. 5 AC in Connect the power cord supplied to this terminal and then turn on the Main Power switch right next to power cord terminal. Use Y1Cb1Cr1/Y2Pb2Pr2, AV, or S-video to connect the VCR, DVD or the Video Game. Audio cable connects to PC audio VGA cable connects to VGA card. DVI cable connects to DVI card (if DVI cable is available) Connect the power supply ANT Connect the cable or antenna Adapter

TV Switch source to TV mode. SOURCE Cycle through input sources: TV Æ VGA Æ DVI Æ S-VIDEO Æ AV1Æ AV2 Æ AV3 Æ COMPONENT 1Æ COMPONENT 2 Also used for selecting the main source during PIP / PBP mode. DISPLAY Displays the current information. Number keys Selects TV channel directly by the numbers. MUTE Turns the speakers On or Off. MTS Selects the TV audio mode; MONO Æ STEREO Æ SAP SOUND Selects the sound enhancement mode: Off-> SRS WOW-> BBE PICTURE Press once or repetitively to select the preset Color modes available ; Soft->Standard->Cool->Define SLEEP Sets the Timer to turn power off (OFF, 10, 20, 30, 60, 90, 120 Min) (Enter) Press to confirm channel selection after entering number directly with key pad. (Recall) Return to previous channel. MENU Press to access main OSD menu. CH d/c Press to tune-in channels up/down and navigate up/down within menu. ZOOM Zoom in or resize screen from 4:3 to Full screen (16:9). VOLe/f Controls volume Up or Down and navigates menu up/down. PIP Activate the PIP / PBP function. SOURCE Selects the sub-screen source under PIP / PBP modes. POSITION During PIP/PBP mode, it adjusts the minor screen’s position. SWAP During PIP/PBP mode, swaps picture between main screen and sub- screen. FREEZE Freeze either the picture of the screen directly (except VGA mode) or the “Activated screen” in PIP main screen. ENTER Press to confirm adjustment of selected item in the OSD menu. C.C. Turn Closed Caption (C.C.) function On / Off. (U.S. area only) V-CHIP Press to open the V-Chip menu. A password is required to access the menu. (U.S. area only)

DDiiisssppplllaaayyy Step 1. Positioning the display set Step 2. Connecting the aerials Step 3. Connecting the power cable Step 4. Remote control Insert the two AAA/UM4-type batteries supplied, making sure that the +/ - polarities are properly aligned. Place your Display set on a solid stable surface. To avoid danger do not expose the display to water, or a heat source. Do not obstruct the ventilation grid at rear. 1. Use for connecting the antenna or coaxial cable (75 Ohms) with TV Tuner socket situated at the back of LCD Display. Insert the power cord plug into the wall socket and then turn on the Main power switch. (located on back) 6 m (19 feet) ① Coaxial F connector / adapter ② Aerial ANT

your antenna or cable TV system (when there is no cable box connected). y Press “MENU” on Remote or TV’s front panel to view OSD “TV PARAMETERS” screen. y Pressf button 3 times to highlight the fifth item “CHANNEL SETTINGS”. y Press “ENTER” to select “SYSTEM”. y Press orbutton to select “Antenna/Cable” then press “MENU”. y Press  button to select “AUTO SCAN” and select “YES” with button to begin the auto channel search. (Pressing “MENU” will stop auto scan) Once Scanning is completed, use the CH or CH buttons to tune-in only receivable channels. Ch. Edit (Channel Edit): While in the “CHANNEL SETTINGS” select “CH. EDIT” to add additional receivable channels and erase unwanted channels during Up/Down tuning. If TV is connected to an antenna, you’ll need to set a few important items in the menu system the first time you turn on your display.

Press the “POWER” key to turn ON the Display. The power indicator changes from red to green. When the power is OFF (standby), the power indicator changes from green to red. BBBaaasssiiiccc O OOpppeeerrraaatttiiiooonnn Power On/Off Source select Press “SOURCE” to select the input signal. Each time the source button is pressed, the on-screen display will cycle between: TV VGA DVI S-VIDEO AV1 AV2 Component2 (Y2Pb2Pr2) Component1 (Y1Cb1Cr1) AV3 TV Button Switch source to TV mode directly without using the source key to select. Adjusting the volume Press f on the remote controller to increase the volume. Press e to decrease the volume. Channel select Press c on the remote controller to change to the next viewable channel. Press d to change to the previous channel or you can select a channel number directly and press “ ” to confirm. Menu On/Off Press “MENU” key to display the OSD main menu On/Off. Use e/f to select the item on the main menu. Press “ENTER” to the submenu and pressd/c navigate up/down. Use e/fto adjust the setting. Press “MENU” key to escape selection or revert to other selections.

O OOSSSD DD M MMEEEN NNU UU D DDEEESSSC CCR RRIIIPPPTTTIIIO OON NN To access MENU, navigate and make adjustments using; MENU、cCH、dCH、 eVOL、f VOL and ENTER. y Pressing “MENU” displays the OSD menu. Use cCH / dCH on the remote controller to scroll the options on the menu. y Press “ENTER” button to enter sub menu. y Usee/f to adjust settings. y Press “ENTER” to confirm desired settings. y Press “MENU” after adjustment is made, to revert to the next adjustment. y Press “MENU” to exit the current OSD menu. Main Menu: There are seven SUB-MENUS in the main OSD Menu. 1. TV PARAMETERS; 2.PC PARAMETERS; 3.AUDIO SETTINGS; 4.Picture-In-Picture; 5.CHANNEL SETTINGS; 6.PARENTAL CONTROLS; 7.GENERAL SETTINGS. In TV mode – Press MENU Use e/f buttons to select the submenu: TV Parameters, Audio Setting, Picture-In- Picture, Channel Settings, Parental Controls, and General Settings. Note: In TV mode, “PC Parameters” cannot be selected. In Video mode (S-VIDEO, AV1 ,AV2, AV3, COMPONENT1(Y1Cb1Cr1) , COMPONENT2(Y2Pb2Pr2)) Press “MENU” button, Main menu will be displayed on the screen (see figure above). Use e/f buttons to select the submenu: TV Parameters, Audio Setting, Picture-In- Picture, and General Settings. Note: 1. In this mode, “Channel Settings” cannot be selected. 2. For devices with PROGRESSIVE SCAN 480p, 720p or 1080i output, connect them to Component-2 jacks to obtain the ideal resolution and picture quality. In PC mode (DVI, VGA) Press “MENU” button, Main menu will be displayed on the screen (see figure above). Use e/f buttons to select the submenu: Audio Settings, Picture-In-Picture and General Settings. Note: In this mode, “TV Parameters” and “Channel Settings” cannot be selected.

TTTVVV///PPPC CC PPPaaarrraaam mmeeettteeerrrsss TV Parameters Press “MENU” and make sure the “TV Parameters” is shown on the screen. Adjusting the TV setting: y Brightness: Alters the brightness of the image. y Contrast: Alters the ratio of light to darkness. y Sharpness: Adjusts the sharpness of the color. y Saturation: Alters the color saturation. y Hue: Alters the color intensity. y Color temp: Adjusts the color temperature of the picture. Three options are available here: 6500, 7500, 9300, and USERS. y Format: Two options are available here: Full screen (16:9) and 4:3. 16:9 4:3 PC parameters Adjusting the picture setting: y Brightness: Alters the brightness of the image. y Contrast: Alters the variation between light and darkness. y Auto: Auto adjusts the position of the image. y Auto color: Auto adjusts the color balance. Note: “AUTO COLOR” function is only available in “VGA” and “Component 2” input sources. By accessing “ALL RESET” function in “General Settings”, the color will return to the factory default setting. y Clock: Adjusts the clock frequency. y Phase: Adjusts the phase frequency. y H-Position & V-Position: Adjusts the horizontal and the vertical position of the image. y Color Temp.: Adjusts the color temperature of the picture. y Format: Two options are available here: Full screen (16:9) and 4:3. y Color Temp. Set Image:

AAAuuudddiiiooo SSSeeettttttiiinnngggsss Press “MENU” and make sure the “AUDIO SETTINGS” is displayed on the screen.  In TV, Video, and PC modes Adjusting the audio setting: y Volume: This will adjust the level of volume. y Mute: Mutes the sound y Bass: This will adjust the level of low frequency content in the sound. (Enabled only when BBE or SRS WOW feature is off) y Treble: This will adjust the level of high frequency content in the sound. (Enabled only when BBE or SRS WOW feature is off) y Balance: This will adjust the relative output of the R/L speakers to obtain the best stereo reproduction. y MTS: This will select the TV audio output. Three options are available: Mono, Stereo, SAP. y Surround: This will select the available audio modes for SRS WOW sound effect. y BBE: This can improve clarity of sound and speech intelligibility. Press “MENU” after adjustment is made. MTS (For TV mode only):

PPPiiiccctttuuurrreee---IIInnn---PPPiiiccctttuuurrreee PIP function: The PIP function allows you to watch two screens on the display from two different sources at the same time. For example; you can watch a TV channel and a component video source at the same time. See PIP structure chart below. Press: PIP To start the PIP function. Off->PIP(Small) ->PIP(Medium) ->PIP(Large)-> PBP -> POP SOURCE To select the sub screen’s source. (See the PIP structure below) POSITION To adjust the PIP position. SWAP To switch the picture of main screen to sub screen. Freeze To freeze the PIP main screen. [Basic function] You can control PIP function easily by remote control. PIP mode PIP source PIP position Swap PIP PBP source & swap POP PIP size –small PIP size–medium PIP size–large Freeze the PIP Source & swap main screen Note: 1. M: main screen; S: sub-screen 2. The PIP submenu can be used to control the sub-screen size. 3. The “SOURCE” button selects the sub-screen. Use the “SWAP” or “FREEZE” buttons to manipulate the main screen. PIP structure Main Screen PIP TV AV1 AV2 AV3 S-Video Component1 (Y1Cb1Cr1) Component2 (Y2Pb2Pr2) VGA DVI TV y y y AV1 y y y AV2 y y y AV3 y y y S-Video y y y Component1 (Y1Cb1Cr1) y y Component2 (Y2Pb2Pr2) y y y y y y VGA y y y y y y y Sub- Screen DVI y y y y y y y y

G GGeeennneeerrraaalll SSSeeettttttiiinnngggsss Press “MENU” and press f to select “GENERAL SETTINGS”. In TV, Video, and PC modes Adjusting GENERAL SETTINGS: y OSD Timeout: Adjusts the OSD elapsed time before disappearing after the last selection. Press e/f to increase or decrease the time. Timeout range: 10, 20, and 30 sec. y OSD Position: Adjusts the horizontal and vertical position of the OSD on the screen. y OSD Language: 4 options available; English, French, Spanish and T. Chinese. (T. Chinese is disabled depending on model) y Display Info. : Shows the Display information on the screen y All Reset: Resets to the factory default settings. y Sleep Timer: With sleep timer you can set a time period after which the TV automatically switches to standby. The counter can be set from 120 Min to OFF as follows; 1. Press “MENU” and select “GENERAL SETTINGS” with f button. 2. Select “Sleep Timer” withd button and press “ENTER” to access submenus. 3. Use e/f to adjust the settings. 4. Press “ENTER” to confirm the setting. 5. Press “MENU” to exit the current OSD page.

G GGeeennneeerrraaalll SSSeeettttttiiinnngggsss Deinterlace: Note: Only available in AV, S-Video, TV1, Component1 input sources. DCDI: This function produces smooth and natural images by minimizing staircasing or jaggies. CCS: This function (CCS) removes “false color” artifacts. FILM Mode: This function produces artifact-free images by proper handling of 3:2 and 2:2 pull-down video motion. Fleshtone: This function can adjust the figure’s skin color to the better Motion: There are three levels: Small, Medium, and Large. Small Î Slight adjustment; Medium Î Medium adjustment; Large Î High adjustment. Note: VGA, DVI, Component2 input sources can not access Deinterlace control.

PPPaaarrreeennntttaaalll C CCooonnntttrrrooolllsss Closed caption: To aid the hearing impaired, Closed Caption is a system which displays a text of the voice dialogue of television programs. This feature uses onscreen text boxes to show conversation and dialogue while the program is in progress. Usually C.C. 1 is the most used. C.C. 2 may be used for alternate languages. Text function is usually used for channel guide, schedules, bulletin board information for Closed Caption programs. CC Control: Use remote control: Press “C.C.” key on the remote control and the closed caption OSD will show on the screen. Use menu: Close Caption setting can also be accessed using the main menu. Press MENU and select “PARENTAL CONTROLS”. 1. Use d/c to select a C.C. control item and select “ON”. 2. Text boxes will show on the TV screen. 3. You can select either one of the C.C. modes available; C.C. and TEXT. 4. You can also select; BOX and SHADOW as desired. Note: 1. Not all the programs, videos and commercials are broadcast with closed caption. 2. Closed Caption function is not available in the Video mode of Component 2. Jean: Nice to meet you. Mary: Nice to meet Caption mode - BOX example. Close caption programs on ABC All items are central time 7:00 top of the morning 12:00 noonday news Text mode - BOX example: The TV screen will be blocked. Jean: Nice to meet you. Mary: Nice to meet Close caption programs on ABC All items are central time 7:00 top of the morning 12:00 noonday news Caption mode - Shadow example. Text mode - Shadow example: The TV screen will be blocked. " For U.S. area only

PPPaaarrreeennntttaaalll C CCooonnntttrrrooolllsss V-chip: The V-chip feature automatically blocks TV programs and movies based on violence, sex, or other content you may believe inappropriate for children. Once you block programs, you can unblock by entering a password. Use remote control: 1. Press “V-Chip” key on the remote controller and the V-Chip OSD will be displayed on the screen. 2. Select the submenu: “Set Password”, “MPAA Rating” & “TV PG Rating” while the V- Chip Lock is in the “OFF” mode. After setting up the sub menu, you must set the V- Chip Lock mode to “ON” to enable the V-Chip function. 3. To turn off the V-Chip function, select “OFF” and press “ENTER”. User is requested to enter the four-digital password before entering V-Chip function. Once the password is entered correctly, you can access the submenu. The default password is “1234”. Use menu: Press “MENU” key to display and select “Parental Controls” to enter the V-Chip OSD and get access to its submenu. V-Chip Lock: Press “V-Chip Lock” to turn V-chip On and Off. MPAA rating: V-chip MPAA (Motion Picture Association of America) uses a rating system applied mainly to movies. A message is displayed on the screen if any rating categories have been blocked. 1. In the “PARENTAL CONTROLS” menu “V-Chip” sub-menu, select “MPAA” and press “ENTER” to confirm. 2. Use d/c to enter and block the categories. Select “NONE” to unblock selected. Ex: The V-Chip will automatically block certain categories that are “more restrictive”. If “R” category has been blocked, then NC-17 and X will automatically be blocked. MPAA Rating None Unblock G General audiences (All ages admitted) PG Parental guidance suggested.(Some material may not be suitable for children) PG-13 Parents strongly cautioned.(Some material may be inappropriate for children under 13.) R Restricted. (Under 17 requires accompanying parent or adult guardian. NC-17 No one 17 and under admitted. X Adults only. No one under 17 admitted. " For U.S. area only

PPPaaarrreeennntttaaalll C CCooonnntttrrrooolllsss TV PG Rating (Parental Guideline) USA V-chip Rating System V-chip reads the program’s age-based rating. If you have blocked the rating, you will receive a rating message on the screen while you select the blocked program - In the “PARENTAL CONTROLS” menu select “V-chip” sub menu. - Select “TV PG Rating” and confirm press “ENTER” to confirm (the default settings are all unblocked). - Use d/c and ENTER select and block the desired categories. Select “NONE” to unblock selected. Note: V- chip function is not available in the Video mode of Component 2. TV P.G. Rating None Unblock none TV-Y All children. none TV-7 Directed to children 7 years and older. The rating of F. Violence can be blocked TV-G General audience. none TV-PG Parental guidance suggested. TV-14 Parents strongly cautioned. The rating of Violence, Sexual Contents, Foul Language or Suggestive Dialog can be blocked TV-MA Mature audience only. The rating of Violence, Sexual Contents or Foul Language can be blocked Ex: The V-Chip will automatically block certain categories that are “more restrictive.” If “TV-14” category has been blocked, then “TV-MA” will automatically be blocked. " For U.S. area only

and you cannot correct the problem, stop using the DISPLAY and contact your dealer or service center at (866) 333-3384 for assistance. SYMPTOMS CHECK ITEMS Make sure the power cord is firmly plugged in the socket. Make sure the power switch is turned on. Make sure the AC socket is OK. No picture a) Power indicator does not light up. Check if the Remote control if it works or must change its batteries Make sure the DISPLAY is ON Check if the signal cable is properly connected. No picture b) Power indicator is green. Increase the CONTRAST and/or BRIGHTNESS. The DISPLAY is on power saving mode, touch the keyboard or the mouse. Make sure the DISPLAY is ON. No Picture c) Power indicator is red. Make sure the signal cable is properly connected. Unclear picture, Noise Make sure the TV signal is received or cables are connected well. Make sure the audio cables are properly connected. Make sure the headphone is not connected. Make sure the “Mute” function is not set. No Sound If picture is received, adjust the TV system setting correctly. Display is too dark or too bright. Lower the contrast and brightness from OSD or input device. Display is not in the center. Adjust the image position using H-position or V-position in OSD. Check if the power voltage is within the spec. Display vibration. Check if the signal cables are properly connected. After-image remains after turns TV off This is characteristic of liquid crystal, it will not cause malfunction and disappear after few minutes Distorted image Make sure the aspect ratio is set properly. Purple image Check if Proper signal type of “Component” or “RGB” setting is set. Out of Range Check if the input signal is acceptable for display. Green, red, blue, white dots on screen This is characteristic of liquid crystal. It will not cause malfunction. Make sure battery’s power or wrong battery orientation. Remove the obstacle between remote control and DISPLAY. Check if one of Key buttons is stuck to cause malfunction. Remote control cannot work Notice that the distance from DISPLAY. Lost password for parental control 1. User must select the submenu “Set Password” in “Parental Controls” menu from OSD and enter the master password: 3609. Then you can set a new password for confirmation. All old settings in “Parental Controls” menu will not be changed any more. 2. You can call service center for master password.

Display Mode Horizontal Frequency Vertical Frequency 31.5 KHz 60 Hz 37.9 KHz 72 Hz 37.5 KHz 75 Hz VGA 640 x 480 43.3 KHz 85 Hz 35.1 KHz 56 Hz 37.9 KHz 60 Hz 48.1 KHz 72 Hz 46.9 KHz 75 Hz 800 x 600 53.7 KHz 85 Hz 48.4 KHz 60 Hz 56.5 KHz 70 Hz 60.0 KHz 75 Hz SVGA 1024 x 768 68.7 KHz 85 Hz SXGA 1280 x 1024 64.0 KHz 60 Hz 1366 x768 47.7 KHz 60 Hz VESA WXGA 1920 x1080 67.2 KHz 60 Hz Note: In PIP function, when selecting VGA or DVI input sources as sub-screen, SXGA timing can not be supported efficiently.