Digimerge DPV24D Instruction Manual

Vandal Models: DPV24D / DPV24TLX Indoor Models: DPD23D / DPD24D Ultra Resolution Day & Night Dome Camera P/N 01.BSM.11.0070201D V5.00 Ultra Resolution Day & Night Dome Camera INSTRUCTION MANUAL

• 1/3” Sony Super HAD™ II CCD • Excellent low light performance using Polaris Vision2 technology. • 0.15 Lux / F1.2 (Color) 0.001Lux w/Sense-Up at x256 • 600 TV lines(Color) of resolution • 3D Digital Noise Reduction (3D-DNR) • OSD menu control • Privacy Masking / Motion Detection • VIDEO OUT(BNC) • Operates in 12VDC or 24VAC • Test Monitor Output • Camera Mounting: Surface / Semi-Flush Mounting (Indoor Dome only) DPD23D • Indoor Dome Model • 3.6mm Fixed Lens DPD24D • Indoor Dome Model • 2.8-10.5mm Varifocal Day/Night Lens F1.4 DC Iris DPV24D • Vandal Resistant Dome Model • 2.8-10.5mm Varifocal Day/Night Lens F1.4 DC Iris DPV24TLX • Vandal Resistant Dome Model • 2.8-10.5mm Varifocal Day/Night Lens F1.4 DC Iris • Smart IR technology • ICR to give clear night vision • ArcticPro technology with built-in heater • 0 Lux with IR LED General DPD23D DPD24D DPV24D DPV24TLX Power source DC 12V / AC 24V +10% Power consumption 2.5 Watts 12 Watts (Heater On) Minimum Power Requirement 250mA 1A Image sensor 1/3” Sony Super HAD™ II CCD Total pixels 811 (H) x 508 (V) Scanning system 2:1 interlace Scanning frequency 15.734KHz(H), 59.95Hz(V) Sync.system Internal / Line Lock Resolution 600 TV Lines Min.Illumination 0.15Lux / 0.001Lux Sense Up at x256 0 Lux IR LED On Video output 1.0 Vp-p (75 ohm, composite) S/N Ratio more than 50dB (AGC OFF) Operating Temperature -10°C - +50°C -40°C - +50°C Power input 2-Pin terminal block (Detachable) Video output BNC Connector (2nd video RCA) Lens mount Fixed mount Lens 3.6mm Fixed 2.8 - 10.5mm F1.4 Varifocal DC Auto iris Operating humidity 0-90% (non-condensing) SPECIFICATIONS -1-

Camera in housing ---------------------------------1 Camera Locking screws (PA3 Type) -----------2 Instruction guide (This Document) -------------1 Surface & Flush Mounting Templates----------2 RCA - BNC test cable ------------------------------1 Junction Box Plate ----------------------------------1 Mounting screw pack ------------------------------1 Vandal Dome package contains the following: Camera in housing ---------------------------------1 Camera Locking screws (PM4 Type) ----------3 Instruction guide (This Document) -------------1 Surface Mounting Template ----------------------1 RCA - BNC test cable ------------------------------1 Junction Box Plate ----------------------------------1 Mounting screw pack ------------------------------1 Tamper allen key ------------------------------------1 Conduit Key ------------------------------------------1 Indoor dome to standard 2S, 4S and Octagon junction boxes. NOTE: Flush side of junction box plate should be attached to junction box Junction Box Fitting plate ------------------------1 2S / 4S plate screws (KM3.5 Type) ------------4 -------------2 Base Fitting Screws PWM3 ----------------------3 JUNCTION BOX PLATE Screw hole overview Base Fitting Screws 88.9 mm 3.5 in 83.3 mm 3.28 in 46.0 mm 1.8 in Base Fitting Screw. Octagon Screw 2S / 4S Screw Locking Screw Conduit Key Allen Key Mounting Screws Pack. 3pc 70mm / 2.8in Screws 3pc 30mm / 1.2in Screws 3pc 40mm 1.6in plugs -2- MEASUREMENTS Vandal Dome Dimensions Base hole positions Ø 0.1" 3.5 mm 3.9" 100.0 mm 3.4" 87 mm 115 mm 4.5 in 137° 123° 100° 7 mm .28 in Underside Base hole positions Indoor Dome Dimensions 3/4’’ -14 NPS thread 4.4" (112 mm) 5.1" (130 mm) 112 mm 4.4 in 5.1" 130 mm Indoor Dome Flush Mount Fitting dimensions 39 mm 1.5 in 27 mm 1.1 in Flush Mount Cutout and Fitting Clearance

VANDAL DOME FITTINGS -5- Pendant Cap - model # MNTV2XPC Replaces the need for the camera base. Compatible with ceiling conduit installations. Pole Mount - model # MNTV2XP Junction Box Attachment for MNTV2XW & MNTV2XC - model # MNTV2XJ Fits either wall mount and ceiling mount. Symmetrical design - reversible for top or bottom conduit. Corner Mount bracket - model # MNTV2XR Pendant Mount - model # MNTV2XC Wall Mount - model # MNTV2XW Junction Box Mount - model # MNTV2XB Can fit either MNTV2XW or MNTV2XJ. Can fit either MNTV2XW or MNTV2XJ. Mount for either Vandal or Indoor Dome. Can also mount MNTV2XC or MNTV2XW. -4- 2S FITTING a. 2S Fitting requires only 2pcs of 2S/4S screws. Note: You have a reduced space in which to hide cables using this type of installation. Recommended for indoor dome only. TWO GANG FITTING a. of 2S/4S screws. Note: A two gang provides the most robust vandal domes. 4S FITTING a. 4S Fitting requires 2pcs of 2S/4S screws. Note: Suitable for both indoor and vandal domes. OCTAGON FITTING a. Octagon screws. Note: are larger compared to those used for the 2S/4S (M4 type). Suitable for both indoor and vandal domes Cable Entry Screws Cable Entry Screws Cable Entry Screws Cable Entry Screws

INSTALLATION. VANDAL DOME -6- 1) Loosen the three tamper screws using the provided allen key. Lift the dome cover. 3a) Reinsert camera module into camera base by aligning the arrow notches on the edge of the camera module and the camera base (label on edge of camera module indicates the location of the arrow notch), and turning camera module clockwise to lock into place. 3b) Use the 3 base locking screws to secure camera base to camera module. Go to step 4 on page 7 to complete installation. Method 1 - Direct Attach Install 2a) Use the included mounting template (Installation Option 2) to mark and pre-drill the required holes. Remove 2 of the 3 base locking screws. Use 2pc of the 2.8” screws to mount the camera directly to the mounting surface. Remove the 3rd base locking screw and install the 3rd 2.8” screw. Go to step 4 on page 7 to complete installation. OR Method 2 - Camera Base Install 2b) Use the included mounting template (Installation Option 1) to mark and pre-drill the required holes. Remove the camera base by unscrewing the 3 base locking screws, and turn camera module approx. 5 degrees counter-clockwise to detach camera base from the camera module. Install the base to the correct holes as indicated on the mount template using the 1.2” screws. Go to step 3a. Method 3 - Junction Box Install 2c) (see page 4 for details). Remove the camera base by unscrewing the 3 base locking screws, and turn the camera module approx. 5 degrees counterclockwise to detach camera base from camera module. Install the base to the junction box using the base attachment screws. Go to step 3a. Installation Option 1: Use holes marked with 'A' when installing camera base first. Use short 30mm screws and anchors. Installation Option 2: Use holes marked with 'B' when installing complete camera housing. Use long 70mm screws and anchors. A A A B B B 1 3 a b a b 2 Mounting Template Conduit Key Allen Key ATTENTION - If using DC power, follow the correct polarity as marked on the power cable. Note: If you plan to use conduit fitting, remove conduit cap using the provided conduit key. -7- 7a) Re-attach the dome cover. Align arrows according to the diagram below to ensure a weatherproof seal. 7b) Use the allen key to tighten the tamper screws. Note: Make sure dome cover cord does not get caught in the rubber seal. 6a) Adjust camera viewing angle and secure into screwdriver. Note: Lens adjustment levers are by default in the locked position. Turn counter clockwise to unlock. Tighten levers to secure lens setting. 6b) Adjust lens and OSD as required. 6c) Re-attach the camera cover, using the thumb screw as a guide, until it snaps into place. 5) Insert the included video test cable into the RCA jack and connect to a test monitor to set up camera. 4) Remove camera cover by squeezing the back and front of the cover (as indicated by the arrow indicators) at the same time and lifting it up and away from the lens. 1 2 3 7 5 6 4 Arrow Video test cable RCA Jack Zoom Thumb Screw Focus Arrow on camera base Correct arrow alignment Arrow on camera module (inside camera) Arrow on dome cover. 1 2 3

1a) Press down on the tab marked with an arrow to lift up the dome cover slightly 1b) While pressing on tab, twist the dome cover counter clockwise just a few degrees to release dome cover from back clips. Lift off the cover. 3a) Reinsert camera module into camera base by aligning the arrow notches, and turning camera module clockwise to lock into place. 3b) Reinstall the base locking screws. (indicated by padlock markings) Go to step 3 on page 9 to complete installation. Method 1 - Direct Attach Install 2a) Use included mounting template to mark and pre- drill the required holes. Use included 2.8” screws to mount the camera directly to the mounting surface. Go to step 3 on page 9 to complete installation. OR Method 2 - Camera Base Install 2b) Use the included mounting template (Installation Option 1) to mark and pre-drill the required holes. Remove the camera base by unscrewing the base locking screws (indicated by padlock markings) and turn camera module approx. 5 degrees counterclockwise to detach camera base from the camera module. Install the base as indicated using the 1.2” screws. Go to step 3a. Method 3 - Junction Box Install 2c) (see page 4 for details). Remove the camera base by unscrewing the 3 base locking screws, and turn the camera module approx. 5 degrees counterclockwise to detach camera base from camera module. Install the base to the junction box using the base attachment screws. Go to step 3a. 1 3 a a b a b b 2 ATTENTION - If using DC power, follow the correct polarity as marked on the power cable. 1 b c 4 2 3 -9- INSTALLATION. INDOOR DOME (Semi-Flush Mount) 1a) Press down on the tab marked with an arrow to lift up the dome cover slightly 1b) While pressing on tab, twist the dome cover counter- clockwise to release dome cover 1c) Remove the camera base by unscrewing the base locking screws (indicated by a padlock markings) and turn camera module approx. 5 degrees counter- clockwise to detach camera base from the camera module. a) Note: Always cut using the inside line of the cutout template b) Insert camera into cutout. Make sure that the mounting arms are not extended. c) Turn screwdriver clockwise to unlock all of the 3 mounting arms. d) Continue turning clockwise to move mounting arms down until they make contact with inner mounting surface. Note: Once mounting arms have made contact with the inner mounting surface, do not apply too much pressure to avoid damaging surface. a) Re-attach the camera cover, using the thumb screw as a guide, until it snaps into place. b) Reattach dome cover. a) Remove camera cover by squeezing the back and front of the cover as indicated by the arrow indicators at the same time and lifting it up and away from the lens. b) Insert the included video test cable into the RCA jack and connect to a test monitor to set up camera. (see page 10). c) Adjust camera viewing angle and secure into place by Adjust lens and OSD as required. Note: Lens adjustment levers are by default in the locked position. Turn counter clockwise to unlock. Tighten levers to secure lens setting. Thumb Screw 1 a b d c b 4 2 3 Zoom Focus ATTENTION - If using DC power, follow the correct polarity as marked on the power cable.

AWB 4. DAY&NIGHT AUTO 5. 3DNR ON 6. SPECIAL 7. ADJUST 8. RESET 9. EXIT 1. LENS DC LENS • DC or MANUAL (Model DPD23D) EXPOSURE • SHUTTER • AGC • SENS-UP • BLC • D-WDR • RETURN WHITE BAL • AWB • ATW • AWC SET • OUTDOOR • INDOOR • MANUAL DAY&NIGHT • AUTO • COLOR • B/W (not on Model DPV24TLX) 3DNR • OFF • ON SPECIAL • CAM TITLE • D-EFFECT • MOTION • PRIVACY • SYNC • LANGUAGE ADJUST • SHARPNESS • MONITOR • OSD COLOR RESET • FACTORY • RETURN MENU TREE SUMMARY • NOTE The brightness level can be adjusted within the range of 0 - 100. Default setting - 50 With Model DPD23D DC Lens setting is MANUAL The EXPOSURE menu is used to set the automatic light control method for the camera. 1. Highlight 'EXPOSURE' in the main setup menu 2. Press the joystick to access the exposure setup menu. EXPOSURE Using this function, you can control screen brightness. 1. Highlight 'LENS' in the main setup menu 2. Press the joystick to access the DC lens setup menu. 3. After completing setting update, highlight 'RETURN' to save setting and return to previous menu SHUTTER : Select the shutter mode. (1/60, FLK - 1/100,000 sec, x2 - 256) Default setting is 1/60 AGC: Auto gain control (LOW / MIDDLE / HIGH) Default setting is MIDDLE LENS SETUP 1. LENS DC 2. EXPOSURE SETUP 1. LENS DC 2. EXPOSURE 3. WHITE BAL AWB EXPOSURE SHUTTER ř/ŞŘ AGC MIDDLE SENSE-UP AUTO BLC OFF D-WDR OFF RETURN RET LENS BRIGHTNESS -----|----ŝŘ RETURN RET 1. Press down on the function joystick to access the setup menu. • Main setup menu is displayed on the monitor screen. 2. Select a function by moving the joystick up and down and move left or right to change setting value and press joystick to confirm selection. 3. If a menu option features a ' ', a sub menu is available which can be accessed by pressing down on the joystick 4. Once finished updating settings, highlight 'EXIT' and press down on the joystick to exit setup menu Menu Setup OSD function joystick. Pressing down on joystick acts as ENTER function. RCA Service Connector Use supplied RCA - BNC cable If you require BNC output.

thereby providing higher sensitivity in low light conditions. NOTE only adjustable if SHUTTER setting is set to 'AUTO' or '1/60' - OFF : Deactivates the SENS-UP function. Selectable low shutter values are as follows: x2 x4 x8 x16 x32 x64 x128 x 256 (default - x8) For proper setup, check setting during low light / night time conditions. - AUTO : Activates SENS-UP function. Enter submenu to select maximum low shutter value • It's recommended to keep the value in the x2 to x64 range to limit ghosting effect. Notes SENSE-UP SENSE-UP xŠ RETURN RET SENSE-UP EXPOSURE SHUTTER 1/60 AGC MIDDLE SENSE-UP AUTO BLC OFF D-WDR OFF RETURN RET The BLC menu is used to adjust backlight compensation function to sharpen subjects in backlight situations 1. Highlight 'BLC' in the exposure setup menu. 2. Press the joystick to access the BLC setup menu. BACKLIGHT (BLC) BLC OFF HSBLC (Highlight Compensation): If a scene contains very bright light sources (e.g. car headlights),they will be masked to provide greater detail in the rest of the scene. Enter the HSBLC submenu to select an area in the scene which requires masking. Change the LEVEL value to set level of masking and change MODE to set whether to mask all day long or during low light conditions only. Default setting is OFF EXPOSURE SHUTTER 1/60 AGC MIDDLE SENSE-UP AUTO BLC OFF D-WDR OFF RETURN RET BLC (Backlight Compensation): Enter the BLC submenu to select an area in the scene which requires enhancing. Change the GAIN value (LOW/MIDDLE/HIGH) to set level of enhancement. BLC GAIN LOW AREA DEFAULT RETURN RET

setup menu. 2. Move the the joystick left/right to change setting to OFF/INDOOR/OUTDOOR. Default setting is OFF The D-WDR menu is used to adjust dynamic range of the camera electronically. This is especially useful in high contrast scenes in order to brighten up darker parts of the scene. White balance function adjusts displayed colors to account for different lighting temperatures. 1. Highlight 'WHITE BAL' in the main setup menu. 2. Move the the joystick left/right to change setting to: AWB / AWCSET / MANUAL / INDOOR / OUTDOOR/ ATW Default setting is AWB (Auto White Balance) White Balance (White Bal.) Wide Dynamic Range (E-WDR) EXPOSURE SHUTTER 1/60 AGC MIDDLE SENSE-UP AUTO BLC OFF D-WDR OFF RETURN RET INDOOR : Preferred setting when camera is installed indoors. Default settings are LOW-6 and HIGH-9 OUTDOOR :: Preferred setting when camera is installed outdoors. Default settings are LOW-11 and HIGH-11 D-WDR INDOOR LOW-LEVEL ----|---- Ş HIGH-LEVEL ----|---- š RETURN RET AWB(Automatic White Balance) : This mode automatically adjusts white balance AWCSET : To obtain the optimum state under the current luminance levels, direct the camera to point toward a sheet of white paper and press the SET button. If the environment changes, including the light source, the white balance will require re-adjustment. MANUAL : The manual adjustment setting enables detailed color adjustment. Select 'ATW' or 'AWB' first then change to 'MANUAL' adjustment setting and press the joystick. Set the appropriate color temperature by increasing / decreasing the red and blue color values and monitor the color changes of the object. Default settings are BLUE-41, RED-45 INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K. OUTDOOR : Select this when the color temperature is between 1,800˚K and 10,500˚K. (sodium light) ATW(Auto Tracking White Balance) : This mode can be used within the color temperature range 1,800˚K ~ 10,500˚K • White Balance may not work properly under the following conditions. In this case select the AWC mode. 1 When the color temperature of the environment surrounding the subject is outside of the supported temperature range (e.g. clear sky or sunset). 2 When the ambient illumination of the subject is dim. 3 If the camera is directed towards a fuorescent light or is installed in a place where illumination changes dramatically, the White Balance function may become unstable. Notes SETUP 1. LENS DC 2. EXPOSURE 3. WHITE BAL AWB 4. DAY&NIGHT AUTO WHITE BAL MANUAL BLUE ----|---- Ŝř RED --|----- Ŝŝ RETURN RET

1. Highlight 'DAY&NIGHT' in the main setup menu 2. Move the the joystick left/right to change setting to AUTO/COLOR/ B/W 3. Press the joystick to access the submenu's for AUTO and B/W settings DAY/NIGHT COLOR : The picture is always displayed in color. B/W : The picture is always displayed in black and white. Press joystick to turn ON or OFF the burst signal in B/W mode. AUTO : The mode is switched to ‘Color ’ in a normal environment, but switches to ‘B/W’ mode when ambient illumination is low. To set up the switching time or speed for AUTO mode, press the joystick. You can now set the Delay in seconds for the Day - Night and the Night - Day transitions. DAY&NIGHT AUTO DELAY -|----- ŝ DN (AGC) ---|--- ŚŘŝ ND (AGC) ---|-- şŞ RETURN RET DAY&NIGHT B/W BURST OFF RETURN RET SETUP 1. LENS DC 2. EXPOSURE 3. WHITE BAL 4. DAY&NIGHT AWB AUTO This function reduces the background noise in a low luminance environment. 1.Highlight '3DNR' in the main setup menu. 2. Move the the joystick left/right to change setting to OFF/ON OFF - Noise is not reduced ON - Noise is reduced 3. Press the joystick to access the submenu for ON setting. In the 3DNR submenu you can adjust the noise reduction level values range from 0 to 100. Default setting is 60. Digital Noise Reduction (3D DNR) •Noise levels can be very subtle, and may not be always noticable on adjusting •When adjusting the noise reduction level in 3DNR submenu, remember that the higher the level set, the more the noise level will be reduced, however this can have a softening effect on the image. Notes śDNR LEVEL -----|---- ŞŘ RETURN RET SETUP 1. LENS DC 2. EXPOSURE 3. WHITE BAL 4. DAY&NIGHT AWB AUTO 5. 3DNR ON

1. Highlight 'SPECIAL' in the main setup menu. SPECIAL. SPECIAL 1. CAM TITLE OFF 2. D-EFFECT 3. MOTION OFF 4. PRIVACY OFF 5. SYNC INT 6. LANGUAGE ENG 7. DEFECT 8. RETURN RET SETUP 1. LENS DC 2. EXPOSURE 3. WHITE BAL AWB 4. DAY&NIGHT 5. 3DNR ON 6. SPECIAL AUTO 7. ADJUST 8. RESET 9. EXIT CAM TITLE : If you enter a title, the title will appear on the monitor. 1. Move the the joystick left/right to change setting to OFF/ON OFF - No camera title is displayed ON - Camera title is displayed •When the CAM TITLE is OFF no title will be displayed on the monitor even if you had previously setup a name. This is the master display setting. Notes 2. Press the joystick to access the submenu for ON setting. Here you will be able to enter the camera title. 3. Move the the joystick left/right/up/down to select a letter/number/symbol and press joystick to confirm selection. Repeat steps until camera title is completed and select 'POS' to select on-screen location for title and 'END' to save title. You can enter up to a maximum of 15 characters. • If you move th e cursor to CLR and press the joystick , all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the joystick. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the joystick. Notes CAM TITLE 0123456789 ABCDEFGHIJK LMNOPQRSTUV WXYZ() ¯-_■/=&:~,.   CLR POS END • Only English is available in this mode for camera title. • Only max 15 characters for the title allowed.

1. Highlight 'D-EFFECT' in the SPECIAL setup menu. Digital Zoom can range from 1x to 32x. Too much digital zoom will result in blocky image Pan / Tilt range is -100 to 100. 2. Press the joystick to access the submenu. 3. FREEZE: Freezes current image displayed 4. MIRROR: MIRROR will mirror the image. V-FLIP, will flip the image vertically. ROTATE, will vertically flip and also mirror. OFF, no image effect applied. 5. D-ZOOM: Allows digital zoom and position to be set. FREEZE OFF MIRROR OFF D-ZOOM OFF NEG.IMAGE OFF RETURN RET SPECIAL 1. CAM TITLE OFF 2. D-EFFECT 3. MOTION OFF 4. PRIVACY OFF 6. SYNC INT 7. LANGUAGE ENGLISH 8. RETURN END D-EFFECT D-ZOOM x 1.0 PAN ----|---- 0 TILT ----|---- 0 RETURN RET D-ZOOM Notes 1. Highlight 'MOTION' in the SPECIAL setup menu 2. Move the the joystick left/right to change setting to OFF/ON 3. Press the joystick to access the submenu for ON setting MOTION: You can monitor activity more efficiently, because a signal is generated by the camera whenever motion is detected. Visual notification is also available. - AREA SELECT: Select motion detection area number. AREA 1-4 With the area slected will be shown fashing on and off visually. - AREA DISPLAY: Turns selected motion detection area ON or OFF. Pressing joystick when ON will change display to set the position and the size of the area. Moving the joystick will change the setting, and press joystick to accept. After you have set both position,size you can RET or AGAIN - SENSITIVITY: Adjust sensitivity for selected motion detection area (0-40). - MOTION VIEW: Turn motion detection view ON or OFF. When turned on, upon detection of motion, motion is shown as green dots to indicate area in which motion is taking place.   POSITION   MOTION MOTION AREA SELECT AREAř AREA DISPLAY ON SENSITIVITY -------|- ŜŘ MOTION VIEW ON RETURN RET •Motion detection is normally part of a DVR which would provide more fexible customization options. Notes SPECIAL 1. CAM TITLE OFF 2. D-EFFECT 4. MOTION OFF 5. PRIVACY OFF 6. SYNC INT 7. LANGUAGE ENG 8. DEFECT 9. RETURN RET

2. Move the the joystick left/right to change setting to OFF/ON 3. Press the joystick to access the submenu for ON setting PRIVACY: ADJUST: Hide an area so that it is not displayed on the monitor. LANGUAGE: The OSD supports English ,Korean,Japanese, Chinese, Simplified Chinese,Russian DEFECT: For Service use only! SYNC: With 24V AC power source, select INT / EXT for Sync, use left/right to select. PRIVACY AREA SELECT AREAř AREA DISPLAY ON COLOR |--------Ř RETURN RET ADJUST SHARPNESS -|------- řŚ MONITOR CRT OSD COLOR ś RETURN RET RESET FACTORY RESET RETURN RET SHARPNESS: Image edge sharpness 0 (soft image) to 31 oversharp (default is 12) MONITOR: CRT/LCD/USER setting for monitor type Note: For direct monitor connection only. (default is CRT) OSD COLOR: 0-15 color for OSD menu text (default is 3) RESET: This will reset all settings for all menus to manufacturer defaults. This allow you to return to shipped settings from the manufacturer. - AREA SELECT: Select privacy area number. AREA 1-8 With the area slected will be shown fashing on and off visually. - AREA DISPLAY: Turns selected privacy area ON or OFF. Pressing joystick when ON will change display to set the position and the size of the area. Moving the joystick will change the setting, and press joystick to accept. After you have set both position,size you can RET or AGAIN - COLOR: Range 0-15. Sets the color of the selected privacy area. ADJUST RESET Nothing appears on the screen.  Check that the power cord and line connection between the camera and monitor are connected properly.  Check that you have properly connected VIDEO cable to the camera VIDEO output jack. The image on the screen is dim.  Is lens stained with dirt? Clean lens with soft, clean cloth.  Adjust the monitor contrast & brightness controls  Re-position the camera if necessary. The image on the screen is dark.  Adjust the contrast feature of the monitor.  If you have an intermediate device, set the 75Ω / Hi-z properly. The camera is not working properly, and the surface of the camera is hot.  Check that you have properly connected the camera to an appropriate power source. The Motion Detection function does not work.  Check that MOTION is turned to ON in SPECIAL submenu. Color is not correct.  Check the setting of WHITE BAL SETUP menu . Refer to the following table if you are experiencing trouble with your camera. Contact an authorized technician if the table does not provide you with a solution to the trouble. As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera. *Standard voltage for camera operation : AC 24V ±10% or DC 12V ±10% *There may be some deviation in voltage drop depending on the type of wire and the manufacturer. When the resistance value of copper wire is at [20˚C(68˚F)] Copper wire size (AWG) #24(0.22mm 2) #22(0.33mm 2) #20(0.52mm 2) #18(0.83mm 2) Resistance (Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 • Be sure to connect power only after all the installation is complete. • Use only UL listed Class 2 AC 24V power transformer. Notes