DigiTech Expression Factory EX-7 Owner's Manual

jack. 10. FOOTSWITCH Plug in the optional FS3X footswitch here. Refer to the Using the Optional FS3X Footswitch section to see what the FS3X can do with the Expres- sion FactoryTM. 11. EXPRESSION PEDAL Serves as a variable control for each of the Effect Models. Also used for engaging the HEEL and TOE SWITCHES, which enable the selected Effect Models and Distor- tion Models. (Refer to the Effect Model Control table for more information about the EXPRES- SION PEDAL.) To enable the HEEL or TOE SWITCHES, press firmly on the heel or toe of the EXPRESSIO ...

1. Power up the Expression FactoryTM Pedal. 2. Select Model 7 using the MODEL knob. 3. Press and hold the HEEL SWITCH for three seconds. The INDICA- TOR LED begins to flash green. 4. Release the HEEL SWITCH. 5. Turn the MODEL knob to Model 5 if you want to use AMP/MIXER mode (which lets you plug into both an amplifier and a mixer simulta- neously). Turn the MODEL knob to Model 6 to select STEREO AMP mode. Leave the MODEL knob at Model 7 to keep the factory default STE- REO MIXER mode selected. 6. Press the TOE SWITCH to exit Flexible Output Mode Setup; the INDICA ...

1. Power up the Expression FactoryTM Pedal. 2. Select Model 7 using the MODEL knob. 3. Press and hold the HEEL SWITCH for three seconds. The INDICA- TOR LED begins to flash green. 4. Release the HEEL SWITCH. 5. Turn the MODEL knob to Model 5 if you want to use AMP/MIXER mode (which lets you plug into both an amplifier and a mixer simulta- neously). Turn the MODEL knob to Model 6 to select STEREO AMP mode. Leave the MODEL knob at Model 7 to keep the factory default STE- REO MIXER mode selected. 6. Press the TOE SWITCH to exit Flexible Output Mode Setup; the INDICA ...

The Expression FactoryTM accommodates the optional FS3X 3-button footswitch. When an Effect Model or an Effect + Distortion Model is enabled, the MODE footswitch toggles between Effect Model only (green LED) and Effect + Distortion Model (red LED), until either the Expression Factory’s TOE SWITCH (Effect Model) or HEEL SWITCH (Effect Model + Distortion Model) has been pressed to put the Expression Factory into bypass. The DOWN footswitch selects the next model down. Pressing and holding the DOWN footswitch for three seconds selects Model 1. The UP footswit ...

put Modes: 1. Mono Mode – Outputs a mono signal through either the OUT 1 (AMP) jack or the OUT 2 (MIXER) jack. 2. Stereo Mixer Mode – Outputs a stereo signal through both the OUT 1 (AMP) and OUT 2 (MIXER) jacks, suitable for connecting to a mixer or recording device. 3. Stereo Amp Mode – Outputs a stereo signal through both the OUT 1 (AMP) and OUT 2 (MIXER) jacks, suitable for connecting to an ampli- fier. 4. Amp + Mixer Mode – Outputs a mono signal through the OUT 1 (AMP) jack suitable for connecting to an ampli ...

This is the one that set the standard for all chorus pedals. The lush Uni- cord Uni-VibeTM chorus effect adds depth and dimension to your music that is both subtle and spectacular. No wonder the Unicord Uni-Vibe was the choice of so many guitar greats when it was created in the late 60s. True to the original, this model also offers a vibrato option. Control 1 (tip): Chorus/Vibrato – Selects either the chorus or the vibrato effect. Turn the knob all the way to the left to select chorus, or all the way to the right to select vibrato. Control 2 (tip): Intensity – ...

(Amp + Mixer) ...