Spectrum 55405 Assembly Instructions

Assembly Instructions Important Before you begin, read and comply with all safety and operating instructions, and ensure all parts and correct quantities are included. Any parts damaged during shipment must be reported within 5 days of receipt. To report information regarding missing parts or damage, to purchase parts or accessories, or if you have any questions, please contact us. www.spectrumfurniture.com 800-235-1262, 715-723-6750 Thank you for purchasing Spectrum products! Instructor-side locking door for Inspiration Lectern 55405 Phillips screwdriver Tools Required 4mm Hex wrench (included) Glide wrench (included) or 7/16” wrench (for 42”H lectern) Figure 1 Locking door Lock pawl 36”H Inspiration Lectern 42”H Inspiration Lectern (1) 025039 4mm Hex wrench (1) 025069 Glide wrench (5) 0100167 8-32 x 1/2” PH Thread-cutting screw (1) 0109616 29” Solid locking door (2) 037542 #8 x 5/8” PHSM screw (2) 026296 Recessed bumper with washer (2) 0102297 7mm x 30mm JC Wood screws (2) 0107139 Offset door stop (1) 041943 1/4-20 Locknut (1) 026059 1/4” Washer Note: The 55405 locking door can be used on 36”H or 42”H Inspiration lectern versions. • The 42”H lectern is commonly equipped with the door and keyboard tray options. • The 36”H lectern can be equipped with the door or keyboard tray. Not both at the same time. • If the door is used on a 42”H lectern without the optional keyboard tray, Spectrum recommends installing a 4RU rack-mount blank above the door to maintain security. 1. Install door to lectern 1. Align and attach the door hinge to the right side panel mounting holes with (5) 8-32 x 1/2” PH thread-cutting screws. Figure 1. 2. Tighten screws securely, but do not overtighten. Note: If you are using an electric drill driver, be careful not to overtighten the screws. Use a low torque-setting to prevent damage to the threads. 8-32 x 1/2” thread- cutting screws (5 required) Inspiration lectern right side panel

Phillips screwdriver Note: On 42”H lecterns, the upper bumper will be installed in the 2nd hole from the top. Note: On 36”H lecterns, the upper bumper will be installed in the top hole. Recessed bumper #8 x 5/8” PHSM screw Recessed bumper #8 x 5/8” PHSM screw Recessed bumper #8 x 5/8” PHSM screw Recessed bumper #8 x 5/8” PHSM screw Locking door Locking door Right side panel Right side panel 2. Install recessed bumpers 1. With the door closed, remove the (2) existing #8 x 5/8” PHM screws from the right side panel. See Figure 2A for 36”H lecterns, see Figure 2B for 42”H lecterns. 2. Install a recessed bumper into each open hole location with a #8 x 5/8” PHM screw. 3. Tighten screws securely, but do not overtighten.

925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM © 2016 Spectrum Industries Inc., All rights reserved. Door stop 7mm x 30mm JC wood screw Door stop 7mm x 30mm JC wood screw Worksurface Worksurface Base panel Door stop 7mm x 30mm JC wood screw Base panel Lock slot Door stop 1/4” Washer 1/4-20 Locknut Left side panel Left side panel 1/4” Washer Lock slot 3. Install door stops 1. On 36”H Inspiration lecterns, open the door and install the upper door stop to the worksurface, and the lower door stop to the base panel-each with a 7mm x 30mm JC wood screw. Figure 3A. Note: On the upper door stop, use the 1/4” washer between the worksurface and door stop. 1. On 42”H Inspiration lecterns, open the door and install the upper door stop through the notch in the left side panel with a 1/4” washer and 1/4-20 locknut. Figure 3B. 2. Install the lower door stop to the base panel with a 7mm x 30mm JC wood screw. Figure 3B Figure 3A 4. Door stop adjustment 1. The door stop can be rotated slightly to adjust the closed position of the doors. To rotate, loosen the JC screw (or upper door stop locknut on 42”H lecterns) slightly with a 4mm hex wrench. Figure 4. 2. Rotate the door stop until the door contacts the upper and lower bumpers at the same time when closed. Also be sure the lock pawl on the door will align and engage with the lock slot in the left side panel. 3. Re-tighten the JC bolt (or locknut) securely. 4mm Hex wrench (included) Glide wrench (included) or 7/16” wrench (for 42”H lectern) 4mm Hex wrench (included) Door stop JC screw Figure 4 Tools Required Tools Required