Directed Electronics 2102T Installation Manual

trained professional may result in severe damage to a vehicle’s electrical system and components. © 2012 Directed, Vista, CA N2102T 2012-07 Directed Passive Keyless Entry (PKE) Model 2102T Installation Guide

Vehicle Category Installation Specification.............................................................................5 Installation Type Selection...........................................................................................................6 Installation diagram....................................................................................................................7 Wiring connections..................................................................................................................19 D2D port (H2), 4-pin black connector .................................................................................19 Feature Programming...............................................................................................................20 Entering feature programming routine.................................................................................20 Changing feature options..................................................................................................20 Accessing another feature..................................................................................................20 Exiting feature programming..............................................................................................20 Features and Options List...................................................................................................21 SmartLock feature.....................................................................................................................22 Remote pairing........................................................................................................................23 Pairing the FOB to the PKE module:.....................................................................................23 Pairing the PKE system to the remote starter module:.............................................................23 Factory reset............................................................................................................................23 Diagnostics.............................................................................................................................23

Warning! safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can lock and unlock your doors and also arm and disarm your Directed security system when the key fob is in and out of range. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter.

Antenna Mounting and Installation Points In order to maximize range, the following antenna mounting options should be discussed with the customer to better suit their needs. Warning • Do not directly mount the antenna on any metallic surface, this may significally decrease the range. • To insure consistent operation, secure the antenna and make sure they will not move or dangle. • Antennas are fragile, they can break easily. Make sure they are mounted on a solid (non flexible) part. Recommended Antenna Mounting Locations The recommended antenna mounting locations are for reference only. It is still required that you perform the actual range test when installing the antenna to ensure that the range is satisfactory. You may require to relocate the antennas to different areas around the recommended locations until maximum range is achieved. Option 1 Option 2 Option 3 Antennas Since this is a directional antenna, range will be afected by antenna placement/mounting Horizontal range Vertical range Option 4 Note: An optionnal 12-foot antenna (part# SANT-PKE12) can be installed to increase the active zone coverage. When a third antenna is installed, feature 4, option 2 must be enable through the "Features and Options List" section on page 21. Vehicle Category Installation Specification Sub Compact, Compact & Sedan: For optimal performance, install the 18-foot antenna in the headliner or below the rear deck. Note: Installation in the trunk will greatly affect and reduce range and overall system performance. Minivan & SUV: To maximize range in the rear of the vehicle, install the 18-foot antenna in the headliner. Pickup (with cab) & Cargo: To maximize range in the rear of the vehicle, install the 18-foot antenna in the bumper, behind the license plate. Pickup (without cab): Suggested Installation: Option 3. Antennas should be mounted on the driver and passenger side since the tailgate does not require to be controlled. Convertible: Install 8-foot antenna in windshield pillar on driver side and the 18-feet antenna behind the rear seats. Note: On vehicle with fiberglass bodies or convertibles, the range will be significantly increased.

Installation Type Selection Choosing the right installation type according to the device you install. Corresponding installation type according to what device you are installing Page Type 1 - PKE Standalone page 7 Type 2a - PKE + Xpresskit Bypass + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector) page 8 Type 2b - PKE + Xpresskit Bypass + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector) page 9 Type 3a - PKE + Xpresskit Bypass + DIRECTED SmartStart + Autostart or Astrostart Directed Remote Starter (with 4-pin antenna connector) page 10 Type 3b - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector) page 11 Type 3c - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector) page 12 Type 4 - PKE + 4x10/5x10 page 13 Type 5 - PKE + Xpresskit Bypass page 14 Type 6 - PKE + DIRECTED SmartStart + 4x10/5x10 page 15 Type 7 - PKE + Xpresskit Bypass - Remote Start Ready (RSR) + DIRECTED SmartStart page 16 Type 8 - PKE + Xpresskit Bypass - Range Extender (RXT) + XL202 page 17 Type 9 - PKE + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4pin antenna connector) page 18

Installation diagram Type 1 - PKE Standalone 6 Green 6 Black 4 Red 2 Black 2 Black 2 Red 10 Black LED PKE Prog. Button (-) Unlock Output: Blue: 2 (-) Lock Output: Green: 1 (+) Door Sense Input: White/Purple: 4** (-) Starter Kill Output: White/Black: 6 (-) Parking Light Output: White/Pink: 7 (-) Door Sense Input: Blue/White: 10** (-) Unlock (-) Lock (+) Brake (+) Starter (+) Ignition (-) Parking Light (-) Door Sense** Antenna (8 feet) Antenna (18 feet) 86 85 30 87a 87 (+) Brake Input: Purple/Black: 5 (+) Door Sense** Starter Disable: This connection is optional and ad- ditional parts are sold separately. Refer to the Antenna Location and Installation Points section on page 5 for more information. (-) Horn Output: Red/White: 3 (-) Horn This toggle switch will bypass the starter disable. (-) Ground: Black: 2 RX: Blue: 1 (+) 12v: Red: 4 D2D Y CABLE Cut the 4-wire red connector of D2D Y-cable and connect 12v and Ground wires to the corresponding wires of the DIRECTED SmartStartTM cable. Not Used Ground: Black (+)12v: Red Ground: Black (+)12v: Red *Sold separately. **Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 2a - PKE + Xpresskit Bypass + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector) Note: 8210 Antenna Universal Adapter is required and sold separately. These wires are not required in D2D mode. 4 Red (-) Door Status Output (+) Brake Output (+) Brake Input: Purple/Black: 5 (-) Starter Kill: White/Black: 6 (-) Door Sense Input: Blue/White: 10*** (+) Brake Input (-) Door Sense Input*** Remote Starter* 8210 Main Universal Adaptor*: Refer to the 8210 guide. Regular Remote Start Connections To The Vehicle 4 White (+) 12v: Red: 4 (-) Ground: Black: 2 RX: Green: 3 TX: Blue: 1 RX: Blue: 1 TX: Green: 3 (-) Ground: Black: 2 (+) 12v: Red: 4 (-) Ground: Black: 2 RX: Blue: 1 (+) 12v: Red: 4 Xpresskit Interface Module* D2D Y CABLE 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button Antenna** 8210* Antenna Harness** 8210* *Sold separately. **Antenna & Antenna harness are sold with your Remote Starter kit. *** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. D2D Port Antenna D2D Port (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. (+) Ignition Output 86 85 30 87a 87 (+) Starter Wire 4 wires red connector 4 wires white connector 3 wires red connector Starter Disable: This connection is optional and ad- ditional parts are sold separately. This toggle switch will bypass the starter disable. (+) Door Sense Input: White/Purple: 4*** (+) Door Sense Input*** 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 2b - PKE + Xpresskit Bypass + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector) These wires are not required in D2D mode. 4 Red (-) Door Status Output (+) Brake Output (+) Brake Input: Purple/Black: 5 (-) Starter Kill: White/Black: 6 (-) Door Sense Input: Blue/White: 10**** (+) Brake Input (+) Ignition Output (-) Door Sense Input**** Remote Starter* 4 White (-) Ground: Black: 2 RX: Blue: 1 (+) 12v: Red: 4 Xpresskit Interface Module* (+) Door Sense Input: White/Purple: 4**** (+) Door Sense Input**** D2D Y CABLE 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button Antenna** Antenna Harness** *Sold separately. **Antenna & Antenna harness are sold with your Remote Starter kit. ***10-foot Antenna Cable is included in the PKE kit. **** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. D2D Port Antenna 10-foot Antenna Cable*** D2D Port (+) 12v: Red: 4 (-) Ground: Black: 2 RX: Green: 3 TX: Blue: 1 RX: Blue: 1 TX: Green: 3 (-) Ground: Black: 2 (+) 12v: Red: 4 86 85 30 87a 87 (+) Starter Wire Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. Regular Remote Start Connections To The Vehicle (-) Horn Output: Red/White: 3 4 wires red connector 4 wires white connector 3 wires red connector Starter Disable: This connection is optional and ad- ditional parts are sold separately. This toggle switch will bypass the starter disable. Optional Antenna (12 feet)* (Part# SANT-PKE12) 2 White

Type 3a - PKE + Xpresskit Bypass + DIRECTED SmartStart + Autostart or Astrostart Directed Remote Starter (with 4-pin antenna connector) Note: 8210 Antenna Universal Adapter is required and sold separately. These wires are not required in D2D mode. (-) Door Status Output (+) Brake Output (+) Brake Input: Purple/Black: 5 (-) Starter Kill: White/Black: 6 (-) Door Sense Input: Blue/White: 10**** (+) Brake Input (-) Door Sense Input**** Regular Remote Start Connections To The Vehicle 4 White (-) Ground: Black: 2 RX: Blue: 1 (+) 12v: Red: 4 Xpresskit Interface Module* (+) Door Sense Input: White/Purple: 4**** (+) Door Sense Input**** LED CABLE*** 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button The connector depends of the installed bypass. Refer to the DIRECTED SmartStart install guide for proper connection. 4 Red Autostart RS* Astrostart RS* The remote starter model will determine which connector to use. Refer to the DIRECTED SmartStart install guide for proper connection. DIRECTED SmartStartTM * *Sold separately. **Antenna & Antenna harness are sold with your Remote Starter kit. ***DIRECTED SmartStartTM cable is sold with your DIRECTED SmartStartTM system. **** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. D2D Port Antenna (+) 12v: Red: 4 (-) Ground: Black: 2 RX: Green: 3 TX: Blue: 1 RX: Blue: 1 TX: Green: 3 (-) Ground: Black: 2 (+) 12v: Red: 4 (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. D2D Y CABLE Cut the 4-wire red connector of D2D Y-cable and connect RX (Blue), 12v and Ground wires to the corresponding wires of the DIRECTED SmartStartTM cable. Not Used RX: Blue Ground: Black (+)12v: Red (+) Ignition Output 86 85 30 87a 87 (+) Starter Wire Starter Disable: This connection is optional and ad- ditional parts are sold separately. 3 wires red connector 8210 Main Universal Adaptor*: Refer to the 8210 guide. Antenna** 8210* Antenna Harness** 8210* This toggle switch will bypass the starter disable. 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 3b - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 6-pin antenna connector) (+) Door Sense Input: White/Purple: 4**** (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10**** (+) Brake Input: Purple/Black: 5 (+) Brake (-) Door Sense**** (+) Door Sense**** Antenna RF Port ESP Red Connector ESP Black Connector 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button (-) Ground: Black: 2 (+) 12v: Red: 4 LED (+)12v TX (-) Ground RX D2D Y CABLE Antenna** Antenna Harness** 10-foot Antenna Cable*** *Sold separately. **Antenna, Antenna harness & DIRECTED SmartStartTM cable are sold with your Remote Starter kit. ***10-foot Antenna Cable is included in the PKE kit. **** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. Connect these wires to the vehicle. DIRECTED SmartStartTM * 3 wires red connector (+) Ignition Output 86 85 30 87a 87 (+) Starter Wire Not Used Starter Disable: This connection is optional and ad- ditional parts are sold separately. The remote starter model will determine which connector to use. Refer to the DIRECTED SmartStart install guide for proper connection. OR This toggle switch will bypass the starter disable. D2D Red Connector 4 White Xpresskit Interface Module* (+) 12v: Red: 4 (-) Ground: Black: 2 RX: Green: 3 TX: Blue: 1 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 3c - PKE + Xpresskit Bypass + DIRECTED SmartStart + Viper/Python/Clifford Directed Remote Starter (with 4-pin antenna connector) Note: 8210 Antenna Universal Adapter is required and sold separately. (+) Door Sense Input: White/Purple: 4**** (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10**** (+) Brake Input: Purple/Black: 5 (+) Brake (-) Door Sense**** (+) Door Sense**** Antenna RF Port ESP Red Connector ESP Black Connector 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button (-) Ground: Black: 2 (+) 12v: Red: 4 LED (+)12v TX (-) Ground RX D2D Y CABLE *Sold separately. **Antenna, Antenna harness & DIRECTED SmartStartTM cable are sold with your Remote Starter kit. ***10-foot Antenna Cable is included in the PKE kit. **** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. DIRECTED SmartStartTM * 3 wires red connector (+) Ignition Output 86 85 30 87a 87 (+) Starter Wire Not Used Starter Disable: This connection is optional and ad- ditional parts are sold separately. The remote starter model will determine which connector to use. Refer to the DIRECTED SmartStart install guide for proper connection. OR This toggle switch will bypass the starter disable. D2D Red Connector 4 White Xpresskit Interface Module* (+) 12v: Red: 4 (-) Ground: Black: 2 RX: Green: 3 TX: Blue: 1 Connect these wires to the vehicle. 8210 Main Universal Adaptor*: Refer to the 8210 guide. Antenna** 8210* Antenna Harness** 8210* CABLE** 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 4 - PKE + 4x10/5x10 RX: Blue: 1 (-) Ground: Black: 2 (+) 12v: Red: 4 (+) Door Sense Input: White/Purple: 4**** (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10**** (+) Brake Input: Purple/Black: 5 (+) Brake Input (-) Door Sense Input**** (+) Door Sense Input**** These wires are not required in D2D mode. 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button Not Used * *Sold separately. **Antenna & Antenna harness are sold with your Remote Starter kit. ***10-feet Antenna Cable is included in the PKE kit. ****Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. Antenna** Antenna Harness** D2D Port Antenna 10-feet Antenna Cable*** D2D Y CABLE (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. 4 wires red connector 3 wires red connector (+) Ignition Output 86 85 30 87a 87 (+) Starter Wire Connect these wires to the vehicle. Starter Disable: This connection is optional and ad- ditional parts are sold separately. This toggle switch will bypass the starter disable. 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 5 - PKE + Xpresskit Bypass Not Used (+) Door Sense Input: White/Purple: 4** (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10** (+) Brake Output (-) Door Sense Output** (+) Brake Input: Purple/Black: 5 (+) Door Sense Output** 4 White Xpresskit Interface Module* (-) Unlock Output: Blue: 2 (-) Lock Output: Green: 1 These wires are not required in D2D mode. RX: Blue: 1 (-) Ground: Black: 2 TX: Green: 3 (+) 12v: Red: 4 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button RX: Blue: 1 TX: Green: 3 (-) Ground: Black: 2 (+) 12v: Red: 4 D2D Y CABLE (-) Unlock Input (-) Lock Input (-) Parking Light Output: Pink/White: 7 *Sold separately. **Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. D2D Port (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. 4 wires red connector 3 wires red connector 4 wires white connector 86 85 30 87a 87 (+) Starter Wire Connect these wires to the vehicle. (+) Ignition Output Starter Disable: This connection is optional and ad- ditional parts are sold separately. This toggle switch will bypass the starter disable. 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 6 - PKE + DIRECTED SmartStart + 4x10/5x10 These wires are not required in D2D mode. 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button CABLE** TX: Blue: 1 RX: Green: 3 (-) Ground: Black: 2 (+) 12v: Red: 4 *Sold separately. **DIRECTED SmartStartTM cable is sold with your DIRECTED SmartStartTM. ***Antenna & Antenna harness are sold with your Remote Starter kit. ****10-feet Antenna Cable is included in the PKE kit. Note: Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. * (-) Ground: Black: 2 (+) 12v: Red: 4 RX: Blue: 1 LED D2D Y CABLE Cut the unused connectors of D2D Y cable and connect RX (blue), 12v and Ground wires to the corresponding wires of the D2D cable. Not Used RX: Blue Ground: Black (+)12v: Red D2D Port Antenna*** Antenna Harness*** 10-feet Antenna Cable**** Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. DIRECTED SmartStartTM * 3 wires red connector (+) Door Sense Input: White/Purple: 4 (Door sense: See note) (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10 (Door sense: See note) (+) Brake Input (-) Door Sense Input (See note) (+) Brake Input: Purple/Black: 5 (+) Door Sense Input (See note) (-) Horn Output: Red/White: 3 86 85 30 87a 87 (+) Starter Wire Connect these wires to the vehicle. (+) Ignition Output Starter Disable: This connection is optional and ad- ditional parts are sold separately. This toggle switch will bypass the starter disable. Not Used (+)12v TX (-) Ground RX 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 7 - PKE + Xpresskit Bypass - Remote Start Ready (RSR) + DIRECTED SmartStart (+) Door Sense Input: White/Purple: 4*** (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10*** (-) Ground: Black: 2 (+) 12v: Red: 4 (+) Brake Input: Purple/Black: 5 Remote Start ready Xpresskit Interface Module* RX: Blue: 1 (+) Starter (+) Ignition 86 85 30 87a 87 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button These wires are not required in D2D mode. LED D2D Y CABLE Cut the unused connectors of D2D Y cable and connect RX (blue), 12v and Ground wires to the corresponding wires of the D2D cable. Not Used TX: Blue: 1 RX: Green: 3 (-) Ground: Black: 2 (+) 12v: Red: 4 (-) Unlock Output: Blue: 2 (-) Lock Output: Green: 1 (-) Parking Light Output: Pink/White: 7 *Sold separately. **DIRECTED SmartStartTM cable is sold with your SmartStart system. ***Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. D2D Port Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. (-) Horn Output: Red/White: 3 DIRECTED SmartStartTM * Starter Disable: This connection is optional and additional parts are sold separately. 3 wires red connector Connect these wires to the vehicle. See Remote Start Ready (RSR) install guide according to your vehicle for RSR connections details. This toggle switch will bypass the starter disable. CABLE** RX: Blue Ground: Black (+)12v: Red (+)12v TX (-) Ground RX Not Used 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 8 - PKE + Xpresskit Bypass - Range Extender (RXT) + XL202 Note: 8210 Antenna Universal Adapter is required and sold separately. (+) Door Sense Input: White/Purple: 4*** (-) Starter Kill Output: White/Black: 6 (-) Door Sense Input: Blue/White: 10*** (-) Ground: Black: 2 (+) 12v: Red: 4 (+) Brake Input: Purple/Black: 5 RX: Blue: 1 86 85 30 87a 87 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button D2D Y CABLE Cut the unused connectors of D2D Y cable and connect 12v and Ground wires. Not Used Ground: Black (+)12v: Red (-) Parking Light Output: Pink/White: 7 *Sold separately. **D2D XOVER Cable, Antenna and Antenna Harness are sold with your RF Kit. ***Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. XL202* XL202: Range Extender Antenna D2D Port Range Extender (RXT) Xpresskit Interface Module* D2D Port Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. (-) Horn Output: Red/White: 3 3 wires red connector 8210 Main Universal Adaptor*: Refer to the 8210 guide. Antenna** 8210* Antenna Harness** 8210* XOVER** Connect these wires to the vehicle. See Remote Start Ready (RSR) install guide according to your vehicle for RSR connections details. (+) Starter (+) Ignition Starter Disable: This connection is optional and additional parts are sold separately. This toggle switch will bypass the starter disable. 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Type 9 - PKE + AutoStart or AstroStart or Viper/Python/Clifford Directed Remote Start- er (with 4pin antenna connector) Note: 8210 Antenna Universal Adapter is required and sold separately. 4 Red (+) Brake Input: Purple/Black: 5 (-) Starter Kill: White/Black: 6 (-) Door Sense Input: Blue/White: 10*** (+) Brake Input (-) Door Sense Input*** Remote Starter* 8210 Main Universal Adaptor*: Refer to the 8210 guide. Regular Remote Start Connections To The Vehicle 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button Antenna** 8210* Antenna Harness** 8210* *Sold separately. **Antenna & Antenna harness are sold with your Remote Starter kit. *** Door sense: The polarity of the door sense in the vehicle will determine which wire to connect from the PKE to the DIRECTED Remote Starter. D2D Port Antenna (-) Horn Output: Red/White: 3 Antenna (8 feet) Antenna (18 feet) Refer to the Antenna Location and Installation Points section on page 5 for more information. (+) Ignition Output 86 85 30 87a 87 (+) Starter Wire Starter Disable: This connection is optional and ad- ditional parts are sold separately. This toggle switch will bypass the starter disable. (+) Door Sense Input: White/Purple: 4*** (+) Door Sense Input*** 2 White Optional Antenna (12 feet)* (Part# SANT-PKE12)

Wiring connections 6 Green 6 Black 4 Red 2 Black 2 Red 10 Black LED PKE Prog. Button Antenna Port Remote Start Antenna Port D2D Port Antenna 8-foot Antenna 18-foot Analog Port 2 White Antenna 12-foot (Optional) Analog Port (H1), 10-pin white connector H1/1 GREEN (-) LOCK OUTPUT H1/2 BLUE (-) UNLOCK OUTPUT H1/3 RED/WHITE (-) HORN OUTPUT H1/4 WHITE/PURPLE (+) DOOR SENSE INPUT* H1/5 PURPLE/BLACK (+) BRAKE INPUT H1/6 WHITE/BLACK (-) STARTER KILL OUTPUT H1/7 PINK/WHITE (-) PARKING LIGHTS OUTPUT H1/8 PURPLE No connection H1/9 PINK No connection H1/10 BLUE/WHITE (-) DOOR SENSE INPUT* * Only one of the Door sense input is required for proper operation. D2D port (H2), 4-pin black connector H2/1 BLUE RX H2/2 BLACK (-) GROUND H2/3 GREEN TX H2/4 RED (+) 12V

Feature Programming The feature programming can be done by following the instructions below. Entering feature programming routine To select a Feature, press and release the programming button the corresponding number of times according to the table below, and then press and hold, the LED will flash to indicate the selected feature number. To select this Fea- ture number... Press the program- ming button... And the LED will flashes... Feature 1 Twice Once Feature 2 3 times Twice Feature 3 4 times 3 times Feature 4 5 times 4 times Feature 5 6 times 5 times Feature 6 7 times 6 times Changing feature options Press the programming button the corresponding number of times according to the selected option. The LED will flash the number of times according to the desired option. For example, if you select Option 3, you will press the programming button 3 times. Accessing another feature To change the option in another feature, wait 3 seconds after your last operation and the module will exit the menu program- ming. Repeat the steps in "Entering feature programming" and "Changing feature options" sections to select another feature and option. Exiting feature programming No activity for 3 seconds.

Features and Options List Features Options 1- RF Protocol Selection 1: Viper, Python, Clifford Supercode* Directed new generation receiver technology 2: Viper, Python, Clifford Keeloq Directed older generation receiver technology 3: AstroStart receiver technology 4: AS HDR - FM AutoStart HDR (new style FM based) receiver technology 5: AS HDR - AM AutoStart HDR (AM based) receiver technology 6: AS LDR - FM AutoStart LDR (older style) receiver technology 2- Door Unlock Timing 1: 0.8 sec* 2: 0.4 sec 3: 3.5 sec 4: Double pulse (0.25 sec) 3: Door Lock Timing 1: 0.8 sec* 2: 0.4 sec 3: 3.5 sec 4: Double pulse (0.25 sec) 4: Number of Antenna 1: 2 Antennas (8ft - 18ft)* 2: 3 Antennas (8ft - 12 ft - 18 ft) 3: 1 Antenna (8ft) 5: Smart Lock** 1: 3 minutes timer* 2: 0 minutes timer (No delay) 3: 1 minute timer 4: 5 minutes timer 6: Door Open Interlock 1: ON* The doors will lock as soon as the key fob leaves the zone even if a door is open. 2: OFF The doors will not lock if the key fob leaves the zone while a door is open. * Default option ** See SmartLock feature section for more details.

SmartLock feature The purpose of the SmartLock feature is to prevent the doors from unwanted unlocking/locking when entering/exiting the active zone multiple times for a pre-programmed delay (No delay*,1, 3 or 5 minutes). This is practical in situations such as loading/unloading packages. *SmartLock feature is disabled when it is set to no delay, which is confi gurable. Note: If the Door Open Interlock feature is enabled, the SmartLock feature will not be able to lock a door when it is left opened. For more information about using SmartLock feature, see owner's guide. SmartLock feature diagram 1 2 3 FOB exits the zone: The doors lock, timer starts. FOB re-enters the zone within the pre-programmed delay: Doors unlock, timer is reset and stays frozen. FOB exits the zone: Doors stay unlocked, fresh timer re-starts. 4 FOB re-enters the zone within the pre-programmed delay: Doors stay unlocked, timer is reset and stays frozen. FOB exits the zone: Doors stay unlocked, fresh timer re-starts. The doors will automatically lock once the valid key fob remains out of the active zone longer than the pre-programmed delay. SmartLock feature CANCELLED. SmartLock Feature ON 5 Step 3 & 4 will not cause the doors to lock/unlock as long as the doors are not opened/ closed during the whole sequence.

Remote pairing Important: The antennas must be connected to the PKE module before proceeding to pairing mode. RF Protocole Selection need to be done prior to pair the PKE to the remote starter. See "Feature Programming" section on page 20. Pairing the FOB to the PKE module: 1. Press and release, then press and hold the programming button on the PKE module. The LED will turn on solid indicating that the PKE module is in pairing mode. 2. Release the programming button. 3. Quickly press and release then press and hold the remote AUX button. 4. The fob LED will flash red followed by a green flash to confirm the pairing was successful. 5. If more than 1 red LED flash occurs during the programming process, verify antenna connections and repeat the pairing procedure. Note: Press and release the programming button at any moment to exit remote pairing mode. Pairing the PKE system to the remote starter module: This step is necessary when a remote starter is installed prior to having a PKE system. This allows the remote starter to recog- nize commands from the PKE system. It is important that the FOB be paired to the PKE module first before proceeding with this step. 1. Place the remote starter in remote pairing mode (see the remote starter instructions on remote pairing for more informa- tion). 2. Press and hold the programming button on the PKE. The LED will flash 3 times to confirm that data is being sent to the remote starter. 3. Release the programming button. The remote starter will confirm the remote learning operation. Refer to the remote starter installation guide for more information on remote pairing. Factory reset To execute a factory reset: 1. Disconnect the power supply from the PKE module. 2. Press and hold the programming button. 3. Reconnect the power supply to the module. The LED will flash 5 times quickly to confirm factory reset. Diagnostics LED Parking Lights Flashing rate Event Flashes x1 Flashes x 1 Slow Lock Flashes x 2 Flashes x 2 Slow Unlock Flashes x 3 Flashes x 3 Fast Enabling PKE through FOB (Standalone installation only) Flashes x 3 Flashes x 3 Slow Remote ID being sent to remote starter Flashes x 4 Flashes x 4 Slow PKE learned Flashes x 5 Flashes x 5 Fast Disabling PKE through FOB (Standalone installation only) Flashes x 5 Flashes x 5 Fast Factory reset ON continuously N/A ON con- tinuously PKE disabled

www.directed.com © 2012 Directed—All rights reserved The company behind this system is Directed Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories avail- able. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology. Directed is ISO 9001 registered. Quality Directed products are sold and serviced throughout North America and around the world. Call (800) 274-0200 for more information about our products and services. Designed and Engineered in the USA