Sony VPH-G70Q Protocol Manual

............... .......... ............... AEP SCC-K78A-A SCC-K79A-A PROTOCOL MANUAL MODEL .................... CHASSIS NO. MODEL .......... DEST. .................... CHASSIS NO. VPH-G70Q VPH-G70QM VPH-G70QMG R Canadian US SCC-K81A-A AEP SCC-K82A-A AEP SCC-K89C-A Canadian US MULTISCAN PROJECTOR VPH-D50Q/D50QM VPH-G70Q/G70QM/G70QMG REVISED-1 DEST. VP ...

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenan ...

1. INTRODUCTION This protocol manual describes various commands provided for projectors VPH-G70 and VPH-D50. Using these commands, an external computer is able to control VPH-G70 and VPH-D50. In the following paragraphs, CONTROLLER means an external device such as a PC which controls VPH-G70 and VPH- D50 using these commands. 2. PROTOCOL SPECIFICAT ...

RECEIVER (To) Index 2-2. Command Block Format Code from B0 up to Bn+2 as described bellow shall be transmitted. < Note > n = 16 + the number of bytes of Data transmitted 1 B0 Start Code B2 B3 B4 B5 Group Index Device Index B7 SENDER (From) Index B8 B9 B10 Group Index Device Index B11 CMD1 B12 CMD2 COMMAND B13 CMD3 8 Bn+2 End Code 5 B16 Data Size of ...

2-3. Data of Code 1 Start Condition 2 Index Header /*-- RECEIVER INDEX --*/ /*-- SENDER INDEX --*/ /*-- COMMAND --*/ 3 Data Size 4 Sub Command 5 Data Size 6 Data 7 Check SUM 8 End Condition CONTROLLER Group Index = 0001 hex Device Index = 0001 hex Projector Group Index = 0001 hex Device Index = 0001 hex Bn B0 NAME Start Code NOTE DATA A5 B1 B2 B3 ...

FUNCTION RETURN DATA FROM PJ STATUS SENSE SYSTEM SELECT INTERNAL TEST SIGNAL GEN. SIRCS CODE DIRECT ACTIVE MEMORY READ ACTIVE MEMORY WRITE Place Data for a Command Block as follows for VPH-G70 / D50. ¥ Command Blocks from B0 up to Bn+2 shall be transmitted continuously. Transfer interval between bytes within a Command Block sent from CONTROLLER shall ...

2-4. Connection Connector : 9 Pin D-subminiature female(D-9S) If CONTROLLER is wired with RS-232C and PROJECTOR is with RS-422A, the following connection is recommended. 2-5. Communication Procedure Communication between CONTROLLER (such as a PC) and DEVICE (such as a PROJECTOR) shall be performed with transmission of a Command Block format. Commun ...

2-6. Communication Rules • INDEX NUMBER of PROJECTOR shall be set to ‘01’. • After transmission of a Command to PROJECTOR, CONTROLLER shall not send the next Command before receiving Return Data ( CMD1=10 hex ) from PROJECTOR. If not, any Data is not transmitted from PROJECTOR, neither any Error Code. • In case of a communication error, P ...

B22 Check SUM 2A B19 Data3 00 B11 CMD1 32 B12 CMD2 08 B14 Data Size 07 B13 CND3 10 B15 Sub Command 00 B16 Data Size 05 B17 Data1 01 B18 Data2 01 B20 Data4 00 B21 Data5 00 Please pay special attention to the following ERROR Data, when SIRCS DIRECT COMMAND is transmitted. 04 : SIZE ERROR The value of Data is not ‘2’. 05 : SELECT ERROR The value o ...

FUNCTION COMMAND DIRECTION CMD1 CMD2 DATA RETURN DATA ACK(ACKNOWLEDGE) CONTROLLER + + + + PROJECTOR 10 10 00 FROM PJ ACK WITH DATA CONTROLLER + + + + PROJECTOR 10 20 DATA 1 DATA 2 ~ DATA N NAK(NOT ANKNOWLEDGE) CONTROLLER + + + + PROJECTOR 10 F0 ERROR DATA COMMAND ERROR 01 UNDEFINED COMMAND 02 PROJECTOR HEAD IS NOT POWER ON 03 ANY PRO ...