Directed Electronics Concept 550 Owner's Manual

limited lifetime consumer warranty Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the life- time of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally rein- stalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone num- ber and address; the authorized dealers name, telephone number and address; complete prod- uct description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including with- out limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-trans- ferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what con- stitutes excessive damage and may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CON- NECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIM- ITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUN- TY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCI- DENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL

THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON- TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1-800-876-0800. Directed security systems, including this unit, are deterrents against possible theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft of the automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without limitation, liability for theft, damage and/or vandalism. Directed does not and has not autho- rized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this security system. Make sure you have all of the following information from your dealer: A clear copy of the sales receipt, showing the following: z Date of purchase z Your full name and address z Authorized dealer's company name and address z Type of alarm installed z Year, make, model and color of the automobile z Automobile license number z Vehicle identification number z All security options installed on automobile z Installation receipts trademarks and copyrights Bitwriter™, Clifford®, Code-Hopping™, Directed®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®, Nuisance Prevention Circuitry®, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stealth Coding™, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed Electronics, Inc. important! Please note that this manual was intended for US consumers and therefore includes American phrases or words.

limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . .i trademarks and copyrights . . . . .ii what is included . . . . . . . . . . . . .2 important information . . . . . . . .2 system maintenance . . . . . . . .3 your warranty . . . . . . . . . . . . .3 fcc/id notice . . . . . . . . . . . . . .3 transmitter configuration . . . . . .4 transmitter functions . . . . . . . . . .5 standard configuration . . . . . .5 using your system . . . . . . . . . . . .6 arming . . . . . . . . . . . . . . . . . .6 disarming . . . . . . . . . . . . . . . .8 disarming without a transmitter . . . . . . . . . . . . . . .8 remote siren silencing . . . . . . .8 transmitter chirp muting . . . . .9 transmitter sensor disable . . . .9 intellistart and smartwindows sensor bypass . . . . . . . . . . . .10 auxiliary channel bypass . . . .10 panic mode with smart door locking . . . . . . . . . . . . . . . . .10 disarm/valet mode . . . . . . . . .11 transmitter valet mode . . . . .12 one-time auto-arming bypass 12 low battery warning . . . . . . .12 multiple event total recall . . .13 false alarm control technology (FACT II) . . . . . . .13 select siren sounds . . . . . . . . . . .14 diagnostics . . . . . . . . . . . . . . . . .15 arming diagnostics . . . . . . . .15 disarming diagnostics . . . . . .15 arm/disarm diagnostic chart .16 table of zones . . . . . . . . . . . .16 anti-code grabbing (ACG) . . . . .17 high frequency . . . . . . . . . . . . . .17 smart power up II . . . . . . . . . . .17 power saver mode . . . . . . . . . . .18 programming options . . . . . . . .18 cliffnet wizard installation software programming . . . . .20 manual programming instructions . . . . . . . . . . . . . .20 user selectable features . . . . .22 user selectable features descriptions - column one . . .22 user selectable features descriptions - column two . . .24 user selectable features descriptions - column three . .26 pin programming . . . . . . . . . . . .28 auto-immobilization feature . .29 auto-immobilization sequence . . . . . . . . . . . . . . . .29 one-time valet feature . . . . .30 sensors . . . . . . . . . . . . . . . . . . . .30 shock sensor . . . . . . . . . . . . .30 adjusting the proximity sensor . . . . . . . . . . . . . . . . . .31 glossary of terms . . . . . . . . . . . .33 health check . . . . . . . . . . . . . . . .35 contents

z Control module and harness z Two five-button transmitters z Presentation envelope and quick reference card z Two window decals z XHF antenna/receiver with harness z Pre-wired blue status LED z PlainView 2 Valet switch z 518C neo-siren z One 504C dual-stage shock sensor with harness z Digital dual-zone proximity sensor important information Congratulations on the purchase of your state-of-the-art vehicle security system. It has been designed to provide years of trouble-free operation. This system must be installed by an authorized dealer. Installation of this product by anyone other than an authorized dealer voids the warranty. As verification of authorization, all authorized deal- ers are provided with preprinted dealer certificates. In order to maximize the use of this system, please review this owner's guide carefully prior to using your system. You can print additional or replacement copies of this owner’s guide by accessing the Clifford web- site at www.clifford.com. 2

system maintenance The system requires no specific maintenance. Your transmitter is pow- ered by a miniature 3V lithium battery that will last approximately one year under normal use. When the battery weakens, operating range will be reduced and the system will provide a low battery warning chirp indi- cation when disarming. your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validat- ed if your warranty registration is not returned. Make sure you receive the warranty registration from your dealer. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer. fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user's authority to operate this device.



 

 




included with your system along with information about compatible Clifford accessories that are not included. For a list of included acces- sories, please refer to the What Is Included section of this manual. Arm/Disarm and Panic Button Trunk Release or Optional Accessory Channel Button Remote Start or Accessory Output Button Silent Arm/Disarm or Accessory Output Button Shift Button

transmitter functions This system uses computer-based code learning to learn the transmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initially comes programmed with stan- dard configuration, but may also be customized using the CliffNet Wizard PC program. The buttons in all of the instructions in this manu- al correspond to a standard configuration transmitter. standard configuration Button The arming, disarming, and panic function are controlled by this button. Button The trunk release or accessory output A is controlled by this button. Button Silent arm and disarm is controlled by this button. Button Remote start is controlled by this button. Button, then Button Accessory B output is controlled by these buttons. Button, then Button These buttons activate SmartWindows.

Button twice, then Button These buttons activate remote valet. Button twice, then Button These buttons disable the sensors. Button three times, then Button These buttons adjust the dual-zone radar sensor. using your system The buttons used in the instructions in this manual correspond to the standard transmitter configuration. If your transmitter has been custom configured, the icons on your transmitter buttons may not correspond to the indicated functions. arming You can activate, or arm, the system by pressing on your trans- mitter for one second. When the system arms, you will hear two short siren sounds, or chirps, and see the parking lights flash twice. The LED will begin to flash steadily. If the vehicle’s power door locks have been connected to the system, the doors will lock.

While the system is armed, the LED status indicator will flash approxi- mately once per second showing that the system is actively protecting your vehicle. If you hear more than two chirps when arming, refer to the Diagnostics section of this guide. These extra chirps confirm a mal- function autobypass. The security system also can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door. Whenever the system is in its 30-second passive-arming countdown. The siren will chirp twice and the lights will flash twice five seconds after the last door has been closed. The system is not actually armed at that point. The system arms and the doors lock (if connected and programmed for passive locking) at 30 seconds, but the siren will not chirp. The early chirps provide you with a 25-second warning prior to arming. When armed, your vehicle is protected as follows: z The LED will flash as a visible theft deterrent. z Light impacts will trigger the Warning Zone signal. When triggered, the siren will sound for a few seconds. z Heavy impacts will trigger the system. The triggered sequence is 30, 60, or 90 seconds of constant siren sounding and flashing parking lights. z If a protected entry (door, hood, or trunk) is opened, the sys- tem will immediately trigger the siren and flash the parking lights. note: If any protected entry point (a door or a switch-protected trunk or hood) is open, the system will not passively arm. Additionally, each time a protected entry is triggered during the arming countdown, the 30-second countdown starts over.

vehicle and it’s contents with an invisible perimeter of pro- tection. disarming To disarm the system, press . You will hear a chirp and the park- ing lights will flash once. If the power locks are connected to the sys- tem, the doors will unlock. If the siren chirps three times when disarm- ing, refer to the Diagnostics section of this guide. This is called Tamper Alert. If the siren is active when the system is disarmed you will hear two chirps but the system is not disarmed. (Refer to the Remote Siren Silencing section of this guide.) However, if the alarm completes the full trigger cycle when disarmed you will hear three chirps. disarming without a transmitter This feature allows you to disarm the system without the transmitter should it be lost, damaged, or disabled. In order to disarm without a transmitter, you must have the vehicle’s ignition key, know where the PlainView 2 Valet switch is located, and have the PIN code. Be sure to check with the installer for the location of the PlainView 2 Valet switch. Please refer to the Disarm/Valet Mode section of this guide for instruc- tions to enter the pin code. remote siren silencing This system offers remote siren silencing. Remote siren silencing is a fea- ture that makes it possible to silence and reset the system when it is triggering without disarming the system. If the system is triggered and

the siren has been sounding, press on the transmitter to stop the trigger and return the unit to the armed state. The system will not dis- arm, but rather reset. This prevents you from disabling the system should you wish to silence it without visually checking the vehicle. After resetting the system, press again to disarm the system. transmitter chirp muting To temporarily turn off the arm or disarm chirps, use transmitter chirp muting. Simply press on the transmitter, and the confirmation chirp(s) will be eliminated for that one operation only. The parking lights will flash to confirm the arm/disarm command. If you want the arm/disarm chirps turned off permanently, please refer to the User- Selectable Features section of this guide. transmitter sensor disable To temporarily disable a sensor input, arm the system, press twice and then . The lights will flash four times and all warn away trigger zones one, three, and eight are bypassed. Press the buttons again; the lights flash four times and both warn away and full trigger zones one, three, and eight are bypassed until the system is disarmed. This can be performed anytime the system is armed. 1. Arm the system. 2. Press twice and then . 3. The lights will flash four times; all warn away zones are now bypassed. 4. Transmit the sensor bypass channel again.

5. The lights will flash four more times; the sensor warn away and full trigger zones are now bypassed. 6. The sensor zones will reset when disarmed. intellistart and smartwindows sensor bypass When the system sees a command to start the vehicle via the Intellistart, it bypasses sensor zones and will continue to bypass these zones until the remote start shuts down. When the system sees a SmartWindows command for up or down operation, the unit will automatically bypass sensor zones one, two, three, and eight until the windows complete their operation. auxiliary channel bypass Alarm sensor input zones one, three, and eight will be bypassed while a pulsed or timed auxiliary Output is active. panic mode with smart door locking If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter! Just press for two seconds to enter Panic Mode. The siren will sound and the park- ing lights will flash for the programmed duration. If the ignition is on, the doors will lock; if the ignition is off, the doors will unlock. To stop Panic Mode at any time press on the transmitter again.

disarm/valet mode Entering your pin code using the PlainView 2 Valet switch allows you to disarm the system or enter valet mode without using the transmit- ter. In valet mode, the security system will not arm, even with the trans- mitter, but all convenience functions (door locks, trunk release, etc.) will continue to work normally. To disarm or enter Valet Mode: 1. Turn the ignition on. 2. Enter PIN code (factory setting is 2). 3. After the last digit of the pin code is entered: a. To disarm the system: press and release . b. To enter valet mode: Press and hold for three seconds. The LED status indicator will light steadily if you are entering Valet Mode and will turn off if you are exiting Valet Mode. To exit Valet Mode: 1. Turn the ignition on. 2. Enter PIN code. 3. After the last digit press for one second. The LED will turn off.

The operations described in this section refer to transmitter buttons. Remember, the buttons used in all the instructions in this guide corre- spond to a Standard Configuration transmitter. This may not be how your transmitter is set up. To enter Valet Mode, press twice and then . The LED status indicator will light solid if you are entering Valet Mode, or will turn off if you are exiting Valet Mode. one-time auto-arming bypass This will bypass the auto arm feature once only. 1. With the key, turn the ignition on, then off within two seconds. 2. The siren will chirp once to confirm auto arming bypass. 3. The system will not auto arm. During auto arming bypass the system will not roll up the windows if SmartWindows is connected, and the accessory output will not auto- activate when using the remote to arm the system. low battery warning When the transmitter battery is low, the system will generate a low- pitched tone when disarmed. note: The system will revert to normal auto arming when the system sees the ignition on for at least three seconds.

multiple event total recall This will report the last eight system triggers. 1. Press and hold of the PlainView 2 Valet switch. 2. While still holding , arm and disarm the system, then release the button. 3. The LED will start to blink to indicate the most recent trigger and proceed down to the eighth trigger. If fewer than eight triggers are stored in memory, the LED will blink continuous- ly until the system is armed/disarmed using the transmitter or the ignition is turned on. For more information, please refer to the Table of Zones section of this guide. false alarm control technology (FACT II) Your system offers FACT II, a feature that prevents annoying repetitive trigger sequences due to a faulty sensor or environmental conditions such as thunder, jackhammers, airport noise, etc. Here’s how it works: The alarm triggers three times. If the same sensor is triggering the alarm and the first and the third triggers are within 60 minutes of each other, FACT II will interpret this pattern of triggers as false alarms. After the third trigger, FACT II ignores, or bypasses, that sensor (along with any other sensors sharing the same zone) for 60 minutes. If the bypassed sensor tries to trigger the system while it is being bypassed, the 60-minute bypass period will start over. This ensures that a sensor that continually triggers will remain bypassed.

open door for three full cycles, the doors will be bypassed until the trig- ger ceases. FACT II is programmable. See the Programming Options section of this guide. select siren sounds To customize siren sounds, please refer to the selectable siren sounds feature in the User Selectable Features grid. Once in programming mode, press on the transmitter to begin playback of the avail- able sounds. Press on the PlainView 2 Valet switch while playing the desired sound to add that sound; press while playing the desired sound to delete that sound. note: Arming and disarming the system does not reset this function! The only way to reset a bypassed zone is for 60 minutes or to turn on the igni- tion. If testing your system, it is important to remember that the FACT II pro- gramming can cause zones to be bypassed and appear to stop working. If you wish to clear the FACT II memory, turn the ignition key on.

diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensors and prevents them from dis- abling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. arming diagnostics If the system is armed while an input is active (door open, sensor trig- gering, etc.) the unit will chirp twice when arming and then four more times five seconds later. This is called Bypass Notification. The security system will ignore the input that was active when the sys- tem was armed, until the input goes away. Three seconds later the sys- tem will monitor that input normally. For example, if your vehicle has interior light exit delay, and you arm the system before the interior light goes out, you may hear Bypass Notification chirps. Once the light shuts off, however, the doors are monitored normally. disarming diagnostics Extra disarm chirps are the Tamper Alert. If three chirps are heard when disarming, the system was triggered in your absence. If three chirps are heard, the LED status indicator will indicate which zone was involved when you turn the ignition on (see the Table of Zones section). The sys- tem will retain this information in its memory. Refer to the Multiple Event Total Recall section of this guide.

table of zones The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If the Warning Zone response is triggered, the LED will not report it. Zone - Number Dealer-Installed of LED Flashes Description Options 1 Proximity sensor 2 Not used 3 Mux 1 trigger - for optional sensors 4 Door switch trigger 5 Instant trigger - trunk 6 Instant trigger - hood 7 Ignition trigger 8 Mux 2 trigger - for optional sensors 9 Not used 10 Power interrupt Action Chirps Light Flashes Description Arm 2 2 System armed Arm 4 4 System armed with hood/ trunk active and bypassed (zones 5 and 6) Arm 2 (5 sec.) 4 2 (5 sec.) 4 System armed with door active and bypassed (zone 4) Arm 2 (10 sec.) 4 2 (10 sec.) 4 System armed with sensor active and bypassed zones 1, 3, and 8 Disarm 1 1 System disarmed Disarm 3 3 System disarmed with tamper alert

anti-code grabbing (ACG) This unit features Anti-Code Grabbing (ACG) with Random Code Encryption. This means the receiver and transmitters each use a math- ematical formula called an algorithm to change their code each time the transmitter is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the bat- tery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode.

Your system will automatically enter Power Saver Mode while armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery and prevents the system from draining the battery. Power Saver Mode takes over under the following conditions: z Power Saver when the system is armed: After the system has been armed for 48 hours, the LED will flash at half its nor- mal rate, decreasing the system's current draw. z Power Saver in Valet Mode: When the system enters Valet Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet Mode, the LED will shut off. If the system remains in Valet Mode, the LED will come back on the next time the ignition is turned on and then back off. programming options Programming options control what your system does during normal operation, and require few or no additional parts. However, some may require additional installation labor. Following is a list of the program settings, with the factory settings in bold: z Active arming (only with the transmitter) or passive arming (automatic arming 30-seconds after the last door is closed).

z Arming/disarming confirmation siren chirps on or off. z Auto-Lock on/off/rpm ON: The doors will lock three seconds after the ignition is turned on unless a door is open. RPM: The doors will lock when the engine speed increases (available only with Intellistart 4). z Auto-Unlock on/off: With this feature on, the doors will unlock when the ignition is turned off. z Passive door locking (with passive arming) or active door locking (only when arming with the transmitter). Passive locking allows the vehicle's doors to lock when the security system passively arms (after the 30 second countdown). This feature only works if passive arming has been programmed. z Panic mode enabled/disabled: Some states have laws against siren capability while driving. z Full trigger response 30, 60, or 90 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance. z False Alarm Control Technology (FACT II) on or off: Please refer to the FACT II section of this guide for a complete explanation of how FACT II operates. If FACT II is pro- grammed off, the security system will respond to inputs from any sensor indefinitely. z Siren tones and chirp volume: The output of the siren con- sists of six different tones in sequence and the arm/disarm chirp volume can be changed or eliminated. z Reset the system to all factory defaults note: Because many states have laws regulating security systems, pro- gramming FACT II off may cause your system to violate state laws.

z Change PIN code. z Custom configure the remote control. z Remote valet on or off. z Autostart with low battery voltage or cold temperature. cliffnet wizard installation software programming Cliffnet Wizard provides access to all available system features and some that are not available when manually programming with the Valet switch. Cliffnet Wizard is compatible with Microsoft Windows 95/98/2000/ME/XP/NT so most programming operations can be accomplished by pointing and clicking with a mouse. This eliminates the need for programming grids and lengthy programming sequences. For a complete guide to system programming using the Cliffnet Wizard refer to the Cliffnet Wizard help menu. manual programming instructions Be sure to document changes by taking note of all feature changes made in programming mode. To enter the User Selectable Features programming: 1. Ignition on - Turn the ignition to the run position or start the engine. 2. Enter PIN - Enter the factory preset PIN code 2 by pressing on the PlainView 2 Valet switch twice, then once.

3. Hold/Chirp/Release - After entering the PIN code, press and hold until a chirp is heard and the LED turns on, then release the button. You have now entered the feature selec- tion position of the User Selectable Features grid. 4. Column select - Press the same number of times as the desired column. After a pause the siren will chirp the same number of times as the selected column for confirmation. 5. Feature select - Press the same number of times as the desired feature. The siren will chirp with each press. The fea- ture can now be changed using the remote control. 6. Feature change - Press on the transmitter. If the sys- tem chirps once, the feature has just turned off; if the sys- tem chips twice, the feature has just turned on. If the fea- ture has more than two settings, continue pressing on the transmitter to toggle through the settings. You can advance to any feature in the same column by pressing within 60 seconds; to program a feature in a different column begin at step 4 within 60 seconds. 7. Exit programming - To exit programming mode turn the igni- tion off or wait 60 seconds without pressing the PlainView 2 Valet switch. The siren will chirp three times to indicate pro- gramming mode has been exited. note: Refer to the Feature Descriptions sections of this guide for impor- tant notes and descriptions of the system features and programming. note: If the factory preset PIN has been changed, the new PIN must be entered.

* This feature is only available with optional IntelliStart connected. ** This feature is only available with optional SmartWindows connected. user selectable features descriptions - column one add new remote (auto learn) Auto-learn new five-button Radar2 remote controls to the system in the standard button configuration. Once you have entered the feature, press on the transmitter until you hear a confirmation chirp. Press again until you hear two chirps indicating the new remote is learned.  !  !
            
 ""         
   #$
!     "
 # % $       
  # % % 
""     
  # ""  $    &            '     &'()*)        ''    # "" 
   +' "",     ,             

auto (passive) arm - on/off z On: When the system sees the ignition turn off and the last protected entry (door, hood, or trunk) close, it will begin a 30-second countdown before arming itself. After the first five seconds, you will hear two chirps and the lights will flash. The system will arm 25 seconds later. z Off: The transmitter must be used to arm the system. chirps - on/off/quiet z On: Chirps will sound when arming/disarming the system. z Off: Chirps will not sound when arming/disarming the sys- tem. z Quiet: Chirps will sound when arming/disarming the system but at a lower volume than normal. auto lock - ignition/off/rpm z Ignition: The doors will automatically lock three seconds after the ignition is turned on unless a door is open at that time. z Off: The doors will not lock automatically. z Rpm: The doors will lock when the system sees the engine reach a preprogrammed RPM (available only with Intellistart 4). auto unlock - ignition/off z Ignition: The doors will automatically unlock as soon as the ignition is turned off. z Off: The doors will not automatically unlock when the igni- tion is turned off

z On: The doors will lock when the system passively arms. This feature only applies when passive arming is programmed on. z Off: The doors will not lock when the system passively arms. siren duration - 30/60/90 z The system will sound the alarm for the programmed dura- tion (30/60/90 seconds) during an alarm trigger or when the system is put into panic mode. second unlock - on/off z On: Second unlock output is active when the arm/disarm button is pressed within 10 seconds of disarming the system. z Off: Second unlock output is pulsed at the same time as the unlock output when the system is disarmed. user selectable features descriptions - column two set pin code This feature allows the setting of the user's personal PIN code. For more information, please refer to the PIN Programming section of this guide. select siren sounds The individual sounds the siren produces during an full trigger alarm can be customized for owner recognition of an alarm trigger. For more infor- mation, please refer to the Select Siren Sounds section of this guide. note: The second unlock can be installed by your dealer. Please note that extra parts and labor may be required.

fact II on/off z On: The alarm will bypass for 60 minutes if zones 1, 3, and 8 are triggered three times within a one hour period. z Off: The alarm will respond to zones 1, 3, and 8 inputs indef- initely without bypassing. remote valet on/off z On: The alarm can be put into valet mode with the remote control. z Off: The alarm can not be put into valet mode with the remote control. entry delay on/off z On: If the system has passively armed, it will not trigger for 15 seconds after a door is opened allowing the user to enter the vehicle and disarm the system via the PlainView 2 Valet switch. z Off: There is no entry delay when armed. The system will trigger instantly when a door is opened. reset to default settings z All system settings (except PIN and remote programming) in the User Programming grid will be reset to their default fac- tory setting as indicated in bold lettering. z Press the arm/disarm button of the TX; the siren will chirp twice as confirmation. panic on/off z On: The panic feature is available. z Off: The panic feature is not available.

z This feature is only available with the IntelliStart option. z Off: The vehicle will not autostart. z Battery: The vehicle will only autostart when the car battery gets low. z Temperature: The vehicle will only autostart at a preset low temperature. z Battery and temperature: The vehicle will autostart with a low car battery or low temperature. user selectable features descriptions - column three The features in this column pertain to programming individual trans- mitter channels in custom configurations. Following is an explanation of the features. arm/disarm only The remote control channel programmed into this feature will arm/dis- arm the system only. accessory a output The transmitter channel programmed into this feature will activate the accessory output. note: When programming a new remote control to custom configura- tion a channel must first be programmed to this feature before pro- gramming the remaining channels. note: Temperature and battery calibration and settings can be made only with the Cliffnet Wizard.

accessory b output The transmitter channel programmed into this feature will activate the accessory output. silent mode The transmitter channel programmed into this feature will arm/disarm the system, but the siren will not chirp. remote valet The transmitter channel programmed into this feature will make the system enter/exit valet mode. remote start z This feature is only available with IntelliStart connected z The transmitter channel programmed into this feature will activate or shut down the Intellistart remote start system. window control z This feature is only available with SmartWindows connected z The transmitter channel programmed into this feature will activate the vent or roll down feature of the SmartWindows system. clear all remotes z This feature will erase all remote codes from the system memory. This feature is convenient for erasing any transmit- ters that have been lost, stolen, or incorrectly programmed into the system. z After entering this feature press any button on the transmit- ter; the siren will chirp to indicate that all transmitters have been erased from memory.

Programming Procedure 1. Enter the feature location in the installer programming grid. 2. Immediately press and release of the PlainView 2 Valet switch. 3. Select each digit by pressing 1-9 times, and then press to enter the number into the system. To enter a zero, press only. 4. Wait for two siren chirps after a five second pause or five seconds after the last digit has been entered if using less than four digit code number. 5. Turn off the ignition; the siren will chirp three times. 6. The programming mode is now exited. To program a PIN code of 1032: 1. Press and release once and once. You will hear one chirp. 3. Press and release once. You will not hear a chirp after programming a zero. 5. Press and release three times, and then press once. You will hear three chirps. 6. Press and release two times, and then press once. You will hear two chirps. note: A PIN code cannot begin with a zero.

PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2. Enter the new PIN code. 3. Press and hold for three seconds. z LED turns on: New PIN code is learned and program- ming is complete. z LED stays off: New PIN code is not learned and the sys- tem reverts to the old PIN code. Redo the programming sequence. auto-immobilization feature Auto-immobilization is a feature designed for maximum security; it activates the UltraSecure Immobilization circuitry automatically. auto-immobilization sequence 1. Turn ignition off or disarm alarm 2. After 30 seconds the systems Immobilization circuits activate and engage the starter and ignition interrupt 3. LED blinks at ½ normal speed. Disarming auto-immobilization To disarm auto-immobilization when active, follow any of the sequences listed below.

z Arm the alarm and then disarm the alarm. z Turn the ignition on and enter the system valet/PIN code. one-time valet feature This feature allows the system to be put in valet mode only until the next time the ignition is turned on. OFF: Valet mode will only be exited by using the valet switch or the remote control. ON: Valet mode will be exited every time the ignition is turned on. sensors shock sensor The 504C dual zone magnetic resonance shock sensor provides a warn ing trigger for lighter impacts to the vehicle as well as a full trigger for heavy impacts.

adjusting the proximity sensor It is recommended that adjustments be performed away from fluores- cent lighting, large metal structures, or confined areas that can affect the sensor field. The alarm will exit adjustment mode automatically 60 seconds after the last adjustment signal from the transmitter and revert to its previous settings. NOTE: You MUST exit using the ARM/DISARM button after programming to lock in the new settings! The proximity sensor field takes one to two minutes to settle after entering adjustment mode, so begin adjusting the sensor within 45 seconds and adjust it slowly so it has time to settle. After two minutes you will have a consistent field during adjustment testing. Each zone has 32 settings that are indicated by chirps that raise and lower in fre- quency as adjustments are made. Total adjustment time for this sensor should be five minutes or less. Read the following instructions thoroughly for a full understanding of how to properly adjust this sensor. 1. Disarm system 2. Transmit Channel 16. (Press 3 times then 1 time) z The LED will turn on and the siren will chirp 1 time. z Primary (full trigger) zone adjustment has now been entered. z Primary zone can now be adjusted. 3. Adjusting Primary Zone z Press of the remote control to increase sensitivity.

z The sensor Primary zone can be tested at any time dur- ing adjustment and will generate 1 siren chirp each time the zone is activated. 4. Press to adjust Warn-Away zone z Siren chirps 1 time. z Warn-away Zone adjustment has now been entered. z Warn-away Zone can now be adjusted. 5. Adjust Warn-away Zone z Press to increase sensitivity. z Press to decrease sensitivity. z The sensor Warn-away zone can be tested at any time during adjustment and will generate 1 siren chirp each time the zone is activated. 6. Press of the remote control to return to Primary zone adjustment and lock in Warn Away zone setting. z Siren chirps 2 times z Primary zone can now be re-adjusted as described in step 3. z Or press again to lock in primary zone setting and exit programming mode. z The siren will chirp 3 times when sensor adjustment mode has been exited. z Auto-Scroll for adjusting sensitivity - press and hold or to increase or decrease sensitivi- ty setting several levels rapidly.

glossary of terms Control Unit: The "brain" of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which mon- itors your vehicle and controls all of the system's functions. Input: A physical connection to the system. An input can be provided by a sensor, pinswitch or through an existing system in the vehicle, such as ignition or courtesy lights. LED: Blue light mounted somewhere in the vehicle. It is used to indi- cate the status of your system. It is also used to report triggers and faults in the system or sensors. UltraSecure Immobilizer: A feature on the module which prevents the vehicle’s engine from operating whenever the system is armed. The vehicle is never prevented from running when the system is disarmed, in Valet mode, or loss of power. PlainView 2 Valet Switch: A small two-button switch mounted some- where inside the vehicle. It is used to override the alarm when a trans- mitter is lost or damaged, or to enter or exit Valet mode. Siren: Noise generating device usually installed in the engine compart- ment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the six tones you hear while the alarm is triggered. Transmitter: Hand-held transmitter which operates the various func- tions of your system. Trigger or Triggered Sequence: This is what happens when the alarm goes off or trips. The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration.

cle will generate the Warning Zone response. It consists of a warning siren blast or beep. Zone: A zone is a separate input that the alarm can recognize as unique. Each input to the system is connected to a particular zone. Two or more inputs often share the same zone. security & convenience expansions Here we have listed only some of the many expansion options avail- able. Please contact your dealer for a complete list of all the options available to you. Backup Battery: The 520T keeps the system armed, triggers the alarm and keeps the immobilization circuits active if main battery power is discon- nected. Power Trunk Release: The button can operate a factory power release for the vehicle’s trunk or hatch. (An optional relay may be re- quired.) If the factory release is not power activated, the Directed®'s 522T trunk release solenoid can often be added. Power Window Control: Automatic power window control is provided with the SmartWindows system. Remote Start System: For the ultimate in convenience, the IntelliStart remote start system can start your vehicle, monitor engine functions, and power your climate control system with a push of a button! Over- rev protection, open-hood lockout, brake pedal shutoff, and automat- ic timer shutoff are all included.

health check Directed Electronics recommends you return to your installing Clifford deal- er to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. note: There may be a small charge incurred for this service.

www.directed.com © 2004 Directed Electronics, Inc. - All rights reserved G909620 08-04 The company behind this system is Directed Electronics, Inc. Since its inception, Directed® has had one purpose, to provide consumers with the finest vehi- cle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed® is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world. E&OE, specification is subject to change without notice. Some vehicles require optional parts/wiring and a few are incompatible with some features. Directed® is committed to delivering world-class quality products and services that excite and delight our customers.