Sony CBK-MB01 Installation Manual

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen. ! AVERTISSEMENT Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement.

. MY-113 board (1) . Precision screws P1.4 x 3.5 (2) . Installation Guide (1) . Installation Manual (1) In addition to the Installation Manual, the following manuals are available. . DVW-970/970P Operation Manual (Supplied with DVW-970/970P) This manual is necessary for application and operation of DVW-970/970P. . CBK-MB01 Maintenance Manual This manual intended for use by trained system and service engineers describes the information (Block diagrams, schematic diagrams, Parts list and etc.) required for parts-level service. For obtaining, contact your local Sony Sales Office/Service Center. Part number: 9-968-182-0X 1-2. Installation Procedure Outline of the installing the CBK-MB01 to the DVW-970/970P is listed as follows. For the details of the installation work, refer to the respective sections. n When removing or installing the plug-in board, be careful not to damage the parts on circuit board, not to insert the boards in the wrong slot and not to insert the boards in wrong directions. Installation procedure Sections describing the detailed procedure 1. Opening the Inside Panel 1-3. Opening and Closing the Inside Panel Assembly 2. Removing the DCP Board Assembly 1-4. Removing and Installing the DCP Board Assembly 3. Removing the DVP Board Assembly 1-5. Removing and Installing the DVP Board Assembly 4. Installing the CBK-MB01 (MY-113 Board) 1-6. Installing the CBK-MB01 (MY-113 Board) 5. Installing the DVP Board Assembly 1-5. Removing and Installing the DVP Board Assembly 6. Installing the DCP Board Assembly 1-4. Removing and Installing the DCP Board Assembly 7. Closing the Inside Panel 1-3. Opening and Closing the Inside Panel Assembly 8. Operation Check 3-2-5. Starting a Shoot with a Few Seconds of Pre-Stored Check that the cache rec function works correctly Picture Data (Picture Cache Function: with CBK-MB01) (Refer to the DVW-970/970P Operation Manual)

1-3. Opening and Closing the Inside Panel Assembly Opening n Be sure to set the POWER switch to OFF, unplug the power cord or remove the battery before starting any of the following procedure to protect inside of the unit from damage. 1. Loosen the four screws (with drop-safe) and open the inside panel assembly in the direction of the arrow. m . The flexible card wire that is connected to the FP- 148 board, will be significantly shortened of its life if it is folded. Be very careful not to fold the flexible card wire. . Stand the unit in the posture that the POWER switch side faces upward when the inside panel assembly is opened. Closing 1. Check that the hinges in the right and left are engaged securely with the hooks of the chassis. 2. Insert the inside panel assembly and tighten the four screws (with drop-safe). n Standard tightening torque : Screw (with drop-safe, B3 x 12) 0.8 N.m (8.0 kgf.cm) n Be careful not to pinch the harness between the inside panel assembly and the chassis. FP-148 board Flexible card wire POWER switch Inside panel assembly Inside panel assembly Hook Hook Hinge Hinge Screws (with drop-safe) Screws (with drop-safe) Screws (with drop-safe)

1-4. Removing and Installing the DCP Board Assembly Removal 1. Open the inside panel assembly. (Refer to Section 1-3.) 2. Disconnect the coaxial cable from the connector (CN10) of the DCP-38 board. (When the CBK-SD01 is installed, disconnect the coaxial cable from the connector (CN1) of the DIF-147 board.) n To disconnect the coaxial cable, do not attempt to disconnect it by pulling the coaxial cable with force. Be sure to hold the plug and disconnect the cable. 3. Remove the screw (B2.6 x 5) and the filter cover. 4. Disconnect the board-to-board connector that comes from the DCP-38 board, and open the CN-2437 board in the direction of the arrow. B2.6 x 5 OK NG Coaxial cable CN-2437 board DCP-38 board CN10 CN-2437 board Board to board connector DCP-38 board Hold the plug to remove Do not attempt to remove by pulling the plug. Filter cover 5. Remove the harnesses from the connectors (CN1, CN3 and CN4) of the VA-228 board. 6. Remove the two screws (B2.6 x 5). 7. Open the board lever in the direction of arrow A, and disconnect the board-to-board connector that is connected to the MB-1032 board. 8. Raise the DCP board assembly about 10 mm in the direction of arrow B, and align the recessed portion of the DCP-38 board with the protruded portion of the board holder. CN4 CN3 CN1 B2.6 x 5 VA-228 board VA-228 board Harness A B A MB-1032 board DCP board assembly DCP board assembly Recessed portion Board-to-board connector Board holder Board holder Board lever

9. Slant the DCP board assembly to the front and remove it. Reinstallation 1. Reinstall the DCP board assembly by reversing the steps 4 to 9 of removal. m . Route the harnesses coming from the connectors (CN1, CN3 and CN4) of the VA-228 board so that they do not jump out of the surface (the surface shown by the arrow) on the VA-228 board. . Route the harnesses so that it is positioned in the recessed portion of the DCP-38 board. DCP board assembly CN4 CN3 CN1 VA-228 board Harness Harness (MA) Recess of the DCP-38 board DCP-38 board 2. Continue reinstallation of the DCP board assembly by reversing the steps 2 to 3 of removal. m . When installing the filter cover, route the harness (MA) connected from the CN-2437 board to the SE- 803 board so that it passes near the screw that secures the upper end of the DCP-38 board. At that time, ensure that the harness (MA) passes between the guides at the upper right and left of the filter cover. . After the CN-2437 board is reinstalled, rotate the filter knob in both directions to confirm that it is not caught by the harness (MA). . Be careful that the harness must not be pitched between the inside panel and the chassis. 3. Close the inside panel. (Refer to Section 1-3.) n Tightening torque : Removal step 6, DCP board assembly (B2.6 screw): 53 x 10-2 ±0.01 N.m (5.3 ±0.1 kgf.cm) Filter cover upper guides Screw DCP-38 board Harness (MA) SE-803 board Filter cover Filter Knob

1-5. Removing and Installing the DVP Board Assembly Removal 1. Open the inside panel assembly. (Refer to Section 1-3.) 2. Remove the DCP board assembly. (Refer to Section 1-4.) 3. Disconnect the flexible card wire from the EQ-88 board connector (CN101). m . Life of flexible card wire will be significantly shortened if it is folded. Be very careful not to fold the flexible card wire. . If the copper plating of the base material exposes due to wear of the tin plated contact of the connec- tor, replace it with the new flexible card wire. CN101 EQ-88 board Flexible card wire 4. Open the board lever in the direction of arrow A and remove the board-to-board connector that is connected to the MB-1032 board. 5. Raise the DVP board assembly in the direction of arrow B by about 15 mm and align the protruded portion of the board holder (F) with the recessed portion of the DVP- 34 board. 6. Slant the DVP board assembly to the front and remove it. A A B MB-1032 board DVP board assembly Board lever Board lever Board-to-board connectors Recessed portion of the DVP board assembly Protruded portion of the board holder (F) DVP board assembly

CN101 CN101 CBK-MB01 Precision screw P1.4 x 3.5 Precision screw P1.4 x 3.5 1-6. Installing the CBK-MB01 (MY-113 Board) Install the CBK-MB01 to the side-A of the DVP-34 board. Installation Procedure 1. Insert the connector (CN101) of the CBK-MB01 (MY- 113 board) into the connector (CN101) on the DVP-34 board firmly. 2. Attach the CBK-MB01 with the two precision screws (P1.4 x 3.5) supplied. n Standard tightening torque value : 12 x 10_2 N.m (1.2 kgf.cm) 1-5. Removing and Installing the DVP Board Assembly 1-6. Installing the CBK-MB01 (MY-113 Board) Reinstallation 1. Raise the board lever to its upright position. 2. Insert the DVP board assembly in a slant angle until the protruded portion of the PC board holder (F) meets the recessed portion of the DVP-34 board. At the above angle, raise the DVP board assembly in the right angle and insert it. 3. When shaft of the board lever enters into the chassis, slant the board lever and push down the board from its top until it is firmly inserted to the board-to-board connector of the MB-1032 board. 4. Reinstall it by reversing the steps of disassembling.

information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des opérations ou entretiens de l’équipement à moins d’une permission écrite de Sony Corporation. Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind. Die Sony Corporation untersagt ausdrücklich die Vervielfältigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben für irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrüstung ohne ausdrückliche schriftliche Erlaubnis der Sony Corporation.