Sony DSX-GS80 Operating Instructions Manual

Owner’s Record The model and serial numbers are located on the bottom of the unit. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DSX-GS80 Serial No. Operating Instructions GB Mode d’emploi FR To cancel the demonstration (DEMO) display, see page 8. For the connection/installation, see page 13. Pour annuler l’affichage de démonstration (DEMO), reportez-vous à la page XX. Pour le raccordement/l’installation, reportez-vous à la page XX.

etc., is located on the bottom of the chassis. The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland. Warning For safety, be sure to install this unit in the dashboard of the car as the left side of the unit becomes hot during use. For details, see “Connection/ Installation” (page 13). FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CLIENTS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Rules and Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy. If you have any questions about this product: Visit: https://www.sony.com/electronics/ support Contact: Sony Customer Information Service Center at 1-800-222-7669 Write: Sony Customer Information Service Center 12451 Gateway Blvd., Fort Myers, FL 33913 Supplier’s Declaration of Conformity Trade Name: SONY Model: DSX-GS80 Responsible Party: Sony Electronics Inc. Address: 16535 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone Number: 858-942-2230 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For the State of California, USA only Perchlorate Material – special handling may apply, See www.dtsc.ca.gov/hazardouswaste/ perchlorate WARNING: Do not ingest battery, Chemical Burn Hazard. The remote commander contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Note on the lithium battery Do not expose the battery to excessive heat such as direct sunlight, fire or the like. Warning if your car’s ignition has no ACC position Be sure to set the AUTO OFF function. The unit will shut off completely and automatically in the set time after the unit is turned off and the clock is displayed (i.e. press and hold OFF for 1 second), which prevents battery drain. If you do not set the AUTO OFF function, press and hold OFF until the display disappears each time you turn the ignition off.

by third parties Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations. Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE. Dear customer, this product includes a radio transmitter. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle. Emergency calls This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies). On BLUETOOTH communication  Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident. – where inflammable gas is present, in a hospital, train, airplane, or petrol station – near automatic doors or a fire alarm  This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.  We do not take any responsibility for the leakage of information during BLUETOOTH communication. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Important notice 4GB

 PTY (program type) Select PTY in RDS. (browse) Enter the browse mode during playback. (Not available when a USB device in AndroidTM mode or iPod is connected.)  Front panel release button  SRC (source) Turn on the power. Change the source. OFF Press and hold for 1 second to turn the source off and display the clock. Press and hold for more than 2 seconds to turn off the power and the display. If the unit is turned off and the display disappears, operation by the remote commander is not available.  Control dial PUSH ENTER Enter the selected item. Press SRC, rotate then press to change the source (timeout in 2 seconds). MENU Open the setup menu. VOICE Press and hold for more than 2 seconds to activate voice dial, voice recognition (Android smartphone only), or the Siri function (iPhone only).  Disc slot  Display window  USB port    / (SEEK –/+) Tune in radio stations automatically. Press and hold to tune manually. / (prev/next) / (fast-reverse/fast-forward) (back) Return to the previous display. MODE CALL Enter the call menu. Receive/end a call. Press and hold for more than 2 seconds to switch the BLUETOOTH signal. Receptor for the remote commander Main unit  Rotate to adjust the volume. Front panel removed (inner panel)

Receive stored radio stations. Press and hold to store stations. ALBUM / Skip an album for audio device. Press and hold to skip albums continuously. (Not available when a USB device in Android mode or iPod is connected.) Press  to thumbs up, or  to thumbs down in Pandora®. (repeat) (Not available when a USB device in Android mode is connected.) (shuffle) (Not available when a USB device in Android mode is connected.) MIC  (play/pause) EXTRA BASS Reinforces bass sound in synchronization with the volume level. Press to change the EXTRA BASS setting: [1], [2], [OFF]. AUX input jack DSPL (display) Press to change display items. SCRL (scroll) Press and hold to scroll a display item. The VOL (volume) + button has a tactile dot. SOUND Open the SOUND menu directly. MENU Press and hold to open the setup menu. /// Select a setup item, etc. ENTER Enter the selected item. Press and hold for more than 2 seconds to establish or terminate the “Sony | Music Center” function. / (prev/next) +/– (album +/–) VOL (volume) +/– Remove the insulation film before use. RM-X231 Remote commander            RESET (inner panel) 

You can detach the front panel of this unit to prevent theft. 1 Press and hold OFF  until the unit turns off, press the front panel release button , then pull the panel towards you to remove. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. Getting Started Attaching the front panel Resetting the Unit Before operating the unit for the first time, or after replacing the car battery or changing connections, you must reset the unit. Press RESET on the inner panel with a ball- point pen, etc., after detaching the front panel. Note Resetting the unit will erase the clock setting and some stored contents. Pairing with a Bluetooth® Device When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other. This unit can connect two BLUETOOTH devices (two mobile phones, or a mobile phone and an audio device). 1 Press MENU, then rotate and press the control dial to select [BLUETOOTH] [PAIRING] [DEVICE 1]/[DEVICE 2]*. flashes while the unit is in pairing standby mode. * [DEVICE 1] or [DEVICE 2] will be changed to the paired device name after pairing is complete. 2 Perform pairing on the BLUETOOTH device so it detects this unit. 3 Select your model name shown in the display of the BLUETOOTH device*. When pairing is made, stays lit. * If passkey input is required on the BLUETOOTH device, input [0000].  

2 Rotate the control dial to select [DEMO], then press it. 3 Rotate the control dial to select [DEMO-OFF], then press it. The setting is complete. 4 Press (back) twice. The display returns to normal reception/ play mode. Canceling the Demonstration Mode You can cancel the demonstration display which appears when the source is off and the clock is displayed. 1 Press MENU, rotate the control dial to Updating the Firmware To update the firmware, visit the support site on the back cover, then follow the online instructions. Notes  Using a USB device (not supplied) is required for updating the firmware. Store the updater in the USB device, and connect the device to the USB port, then perform the update operation.  Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device. About Help Guide For details on the functions and operations that are not covered in this manual, refer to Help Guide. http://xxxxxxxxx

devices on the dashboard. • When the unit is turned on, the power antenna (aerial) extends automatically. • Do not splash liquid onto the unit. Additional Information • You can connect to the following iPod models. Update your iPod devices to the latest software before use. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Playback order of audio files Folder (album) Audio file (track) About iPod Compatible Model Bluetooth® USB iPhone XR   iPhone Xs max   iPhone Xs   iPhone X   iPhone 8   iPhone 8 Plus   iPhone 7   iPhone 7 Plus   iPhone SE   iPhone 6s   iPhone 6s Plus   iPhone 6   iPhone 6 Plus   iPhone 5s   iPhone 5c   iPhone 5   iPhone 4s   iPod touch (6th generation)   iPod touch (5th generation)   iPod nano (7th generation)  Compatible iPhone/iPod models

of the remote commander When the battery becomes weak, the range of the remote commander becomes shorter. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Note on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Cleaning the connectors Avoid touching the connectors directly. The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 7) and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged. Note For safety, do not remove the front panel while driving. Specifications FOR THE CUSTOMERS IN THE USA. NOT APPLICABLE IN CANADA, INCLUDING IN THE PROVINCE OF QUEBEC. POUR LES CLIENTS AUX ÉTATS-UNIS. NON APPLICABLE AU CANADA, Y COMPRIS LA PROVINCE DE QUÉBEC. AUDIO POWER SPECIFICATIONS CTA2006 Standard Power Output: 45 Watts RMS × 4 at 4 Ohms < 1% THD+N SN Ratio: 80 dBA (reference: 1 Watt into 4 Ohms) Tuner section FM Tuning range: 87.5 MHz – 107.9 MHz Usable sensitivity: 8 dBf Signal-to-noise ratio: 73 dB Separation: 50 dB at 1 kHz AM Tuning range: 530 kHz – 1,710 kHz Sensitivity: 26 μV + side up Lithium battery (CR2025) USB Player section Interface: USB (High-speed) Maximum current: Front: 1 A Rear: 1.5 A Maximum number of recognizable files (tracks): 10,000 Compatible Android Open Accessory protocol (AOA): 2.0 Corresponding codec: MP3 (.mp3) Bit rate: 8 kbps – 320 kbps (Supports VBR (Variable Bit Rate)) Sampling rate: 16 kHz – 48 kHz WMA (.wma) Bit rate: 32 kbps – 192 kbps (Supports VBR (Variable Bit Rate)) Sampling rate: 32 kHz, 44.1 kHz, 48 kHz AAC (.m4a, .mp4) Bit rate: 8 kbps – 320 kbps Sampling rate: 11.025 kHz – 48 kHz WAV (.wav) Bit depth: 16 bit Sampling rate: 44.1 kHz, 48 kHz

Output: BLUETOOTH Standard Power Class 2 (Max. Conducted +1 dBm) Maximum communication range*1: Line of sight approx. 10 m (33 ft) Frequency band: 2.4 GHz band (2.4000 GHz – 2.4835 GHz) Modulation method: FHSS Compatible BLUETOOTH Profiles*2: A2DP (Advanced Audio Distribution Profile) 1.3 AVRCP (Audio Video Remote Control Profile) 1.5 HFP (Handsfree Profile) 1.6 PBAP (Phone Book Access Profile) SPP (Serial Port Profile) Corresponding codec: SBC (.sbc), AAC (.m4a) *1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna (aerial)’s performance, operating system, software application, etc. *2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices. Power amplifier section Output: Speaker outputs Speaker impedance: 2 Ω/4 Ω – 8 Ω Maximum power output: 100 W × 4 (at 2 Ω/ 4 Ω) General Power requirements: 12 V DC car battery (negative ground (earth)) Rated current consumption: 10 A Dimensions: Approx. 178 mm × 50 mm × 177 mm (7 1/8 in × 2 in × 7 in) (w/h/d) Mounting dimensions: Approx. 182 mm × 53 mm × 160 mm (7 1/4 in × 2 1/8 in × 6 3/8 in) (w/h/d) Mass: Approx. 1.0 kg (2 lb 11 oz) Package contents: Main unit (1) Remote commander (1): RM-X231 Parts for installation and connections (1 set) Optional accessories/equipment: SiriusXM Connect Vehicle Tuner: SXV100, SXV200, SXV300 Cable for steering wheel remote input: RC-SR1 Ask the dealer for detailed information. Design and specifications are subject to change without notice. FLAC (.flac) Bit depth: 16 bit, 24 bit Sampling rate: 44.1 kHz, 48 kHz

sold separately. www.siriusxm.com Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. Apple, iPhone, iPod, iPod nano, iPod touch, and Siri are trademarks of Apple Inc., registered in the U.S. and other countries. PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, LLC. Used with permission. Android is a trademark of Google LLC. libFLAC Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2013 Xiph.Org Foundation Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: – Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. – Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. – Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyrights

common ground (earth) point. •Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing). •Before making connections, turn the car ignition off to avoid short circuits. •Connect the yellow and red power supply leads only after all other leads have been connected. •Be sure to insulate any loose unconnected leads with electrical tape for safety. •Choose the installation location carefully so that the unit will not interfere with normal driving operations. •Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts. •Use only the supplied mounting hardware for a safe and secure installation. Note on the power supply lead (yellow) When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating. Note on installing in cars with a start-stop system The unit may restart when starting the engine from start-stop. In this case, turn off the start-stop system of your car. Mounting angle adjustment Adjust the mounting angle to less than 30°. Parts List for Installation • This parts list does not include all the package contents. • The mounting sleeve  and the trim ring  are attached to the unit before shipping. Before mounting the unit, use the release keys  to remove the mounting sleeve  from the unit. For details, see “Removing the mounting sleeve”. • Keep the release keys  for future use as they are also necessary if you remove the unit from your car. Connection/Installation  Power supply leads (1)  Trim ring(1)  Mounting sleeve(1)   Mounting screws 5 × max. 8 mm (7/32 × max. 5/16 in) (4)  Microphone (1)  Double-sided tape (1) Release keys (2) Flat-mount base (1) 

(SiriusXM)*1 *5*6 Smartphone*8, iPod/ iPhone*9, USB device *1 Front speaker*1*2*11 Rear speaker*1*2*11 For details, see “Making connections” (page 15). When connecting to the battery directly*12*13 from a car antenna (aerial)*7 from a wired remote control (not supplied)*4 *10  White White/black striped Gray Black Yellow Red Blue/white striped Gray/black striped Green Green/black striped Purple Purple/black striped Orange/white striped Black Yellow

*3 RCA pin cord (not supplied) *4 Depending on the type of car, use an adaptor for a wired remote control (not supplied). For details on using the wired remote control, see “Using the wired remote control” (page 17). *5 Whether in use or not, route the microphone input cord such that it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet. *6 For details on installing the microphone, see “Installing the microphone” (page 16). *7 Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit. *8 To connect a smartphone to the main unit, an appropriate cable (not supplied) is required. *9 To connect an iPod/iPhone, use the USB connection cable for iPod (not supplied). *10 Ferrite sleeve *11 Use speakers with 50W RMS or higher power input capacity. Using Sony XB series full range speakers is recommended. *12 When the amperage rating of the fuse used on your car is 10 A, make the power connection to the battery directly to avoid short circuits. *13 Before connection, arranging the yellow and black leads of the power connector is required.  To the +12 V power terminal which is energized when the ignition switch is set to the accessory position If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to first connect the black ground (earth) lead to a common ground (earth) point.  To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit.  To a car’s illumination signal Be sure to first connect the black ground (earth) lead to a common ground (earth) point.  To a common ground (earth) point First connect the black ground (earth) lead, then connect the yellow and red power supply leads.  To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth) lead to a common ground (earth) point. When connecting to the battery directly When the amperage rating of the fuse used on your car is 10 A, make the power connection to the battery directly to avoid short circuits.  to a metal point of car  to the positive battery terminal Notes • Despite connecting to the power supply lead of the car, the unit may not fully provide its performance due to insufficient power. In this case, make the power connection to the battery directly. • All power wires connected to the positive battery post should be fused within 450 mm (18 in) of the battery post, and before they pass through any metal. • Make sure that the car’s battery wires connected to the car (ground (earth) to chassis)* are of a wire gauge at least equal to that of the main power wire connected from the battery to the head unit. • During full-power operation, a current of more than 15 A will run through the system. Therefore, make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 14-Gauge (AWG14) or have a sectional area of more than 2mm² (3/32 in). When making the speaker parallel connection, use wires with more than 12-Gauge (AWG12) or wire that have a sectional area of more than 3.5 mm² (5/32 in). If you have any questions or problems concerning the connection, consult the dealer for details. Making connections * Less than 450 mm (18 in) +12 V car battery Fuse (15 A)

calling, you need to install the microphone . Cautions •It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations. •If airbags or any other shock-absorbing equipment is in your car, contact the store where you purchased this unit, or the car dealer, before installation. Note Before attaching the double-sided tape , clean the surface of the dashboard with a dry cloth. Installing the microphone Subwoofer Easy Connection You can use a subwoofer without a power amplifier when it is connected to a rear speaker lead. Note Use a subwoofer with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with a 2 Ω impedance or 4 Ω to 8 Ω impedance, and with adequate power handling capacities to avoid damage. Front speaker Subwoofer Speaker Parallel Connection When making the speaker parallel connection for a high volume playback, be sure to: – Make the power connection to the battery directly. – Set [SPEAKER LOAD] in [GENERAL] to [2 Ohm]. Note When using a subwoofer with dual voice coil, or using a subwoofer by connecting the right and left rear speaker leads, be sure to set [SPEAKER LOAD] in [GENERAL] to [2 Ohm]. FL FR RR RL Front speaker (4 Ω to 8 Ω) Rear speaker (4 Ω to 8 Ω) Subwoofer (4 Ω to 8 Ω, dual voice coil type) Clip (non fourni)    

ring  and the mounting sleeve  from the unit. 1 Pinch both edges of the trim ring , then pull it out. 2 Insert both release keys  until they click, and pull down the mounting sleeve , then pull up the unit to separate. • Before installing, make sure the catches on both sides of the mounting sleeve  are bent inwards 2 mm (3/32 in). • For Japanese cars, see “Mounting the unit in a Japanese car”. Removing the mounting sleeve     Face the hook inwards. Mounting the unit in the dashboard When using the steering wheel remote control Installation of the connection cable RC-SR1 (not supplied) is required before use. 1 To enable the steering wheel remote control, select [STEERING]  [EDIT CUSTOM] to make the registration. When the registration completes, the steering wheel remote control becomes available. Notes on installing the connection cable RC-SR1 (not supplied) • Refer to the support sites on the back cover for details, then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit. • Depending on the type of car, be sure to insulate the unused leads with electrical tape for safety. • Do not connect this cable when the steering wheel remote control is not used. • Consulting the dealer or an experienced technician for help is recommended. When using the wired remote control 1 To enable the wired remote control, set [STRG CONTROL] in [STEERING] to [PRESET] . Using the wired remote control CAUTION Do not touch the left side of the unit when removing from the dashboard. The heatsink on the left side of the unit remains hot right after use.

the mounting screws . When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.  to dashboard/center console Existing parts supplied with your car Mounting the unit in a Japanese car You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. TOYOTA  Bracket Bracket  to dashboard/center console Existing parts supplied with your car  Bracket Bracket Detaching and attaching the front panel For details, see “Detaching the Front Panel”(Page 7). Resetting the unit For details, see “Resetting the Unit”(Page 7). Fuse replacement Fuse (15 A) 2 Mount the unit onto the mounting sleeve , then attach the trim ring . Notes • If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. • Make sure the 4 catches on the trim ring  are properly engaged in the slots of the unit.  182 mm (7 1/4 in) 53 mm (2 1/8 in) Catch   1 Position the mounting sleeve  inside the dashboard, then bend the claws outward for a tight fit.

https://www.sony.net/ Site d’assistance Si vous avez des questions ou si vous souhaitez consulter les toutes dernières informations techniques sur ce produit, rendez-vous sur le site Web suivant : Support site If you have any questions or for the latest support information on this product, please visit the web site below: https://www.sony.com/am/support If you have any questions/problems regarding this product, try the following: 1 Read Troubleshooting in Help Guide (online manual). 2 Please contact (U.S.A. only); Call 1-800-222-7669 URL https://www.SONY.com https://rd1.sony.net/help/ev/xxx-xxxx/h_zz/ Help Guide (online manual) For details on the functions and operations that are not covered in this manual, please visit the web site below: Guide d'aide (manuel en ligne) Pour plus de détails sur les fonctions et opérations qui ne sont pas abordées dans ce mode d'emploi, veuillez visiter le site Web ci-dessous :