SmartLock VISION Technical Manual

Default codes (change default codes) Setup (Master) 5-0-5-0-5-0-5-0 Service not installed Manager 1-2-3-4-5-6 Users (1-9) not installed Open the lock • Enter the code and open within 4 seconds. • If time delay is set wait for counting: an acoustic signal indicates open window. • Enter the code and open within 4 seconds. Open the lock with time delay override • Enter override user (9) code. • Enter second code and open within 4 seconds. If lock is already counting time delay enter override user (9) code to immediately open. Change code (door open) • Press and hold 0 until double beep: enter old code. • Enter and confirm new code. Install a user • Press and hold 1 until double beep: enter Manager code. • Enter user ID (1-9). • Enter and confirm new user code. To install Manager enter the function with Service code. Users management • Press and hold 2 until double beep: enter Manager code. • Press P to scroll users list and check their status. • Press 1 to install a user: enter and confirm user code. • Press 2 to disable/enable a user. • Press 3 to delete a user. • Press OK to confirm and exit. Delete a user • Press and hold 3 until double beep: enter Manager code. • Enter user ID (1-9). To delete Manager enter the function with Service code. Test function • Press and hold 5 until double beep. • Enter the sequence: 1-2-3-4-5-6-7-8-9-0. • Double beep: key properly working. Long beep: key malfunction. If lock and keypad don’t communicate display shows the message: NO ANSWER. 1 of 2 OPEN LOCK CODE o o o o o o INSTALL o o o o o o CHANGE o o o o o o ID= 1 ID= 2 ID = 3 DELETE o o o o o o TEST

• Press and hold 8 until double beep, enter Setup code and select function 0. • Enter and confirm new Setup code. Install Service • Press and hold 8 until double beep, enter Setup code and select function 1. • Press OK to confirm the operation. • Enter and confirm new Service code. Delete Service • Press and hold 8 until double beep, enter Setup code and select function 3. • Press OK to confirm the operation. Reset lock • Press and hold 8 until double beep, enter Setup code and select function 5. • Display shows the message RESET. • Press OK to confirm the operation. • Enter a valid code. • Lock is in pre-setup mode. Pre-setup mode • To open press 1. • Setup code (Master) 5-5-5-5-5-5-5-5. Lock setup • Press and hold 8 until double beep. Enter the Setup code 5-5-5-5-5-5-5-5. • Display shows the following options (press P to scroll): • CHANGE: change Setup code to exit pre-setup mode. • SETUP: check (OK) or change (P) lock configuration (bold = default settings) • DELAY DOWN - DELAY UP: time delay counting up or down. • DUAL NO - DUAL YES: dual mode active - dual mode not active. • DIGITS 6 - DIGITS 7 - DIGITS 8: opening codes length. Time delay • Press and hold 9 until double beep and enter Manager code (or Service code) or access Setup menu and press 9. • Display shows current time delay values: press OK to confirm or enter new values (00-99min) and press OK. • Display shows current open window values: press OK to confirm or enter new values (01-19min) and press OK. Time delay can be increased at any moment, decreased only during open window. Change language and check firmware version • Press and hold OK until double beep: display shows serial number and firmware version: press P. • Display shows current language: press OK until the desired language will be selected. 2 of 2 ENGLISH ITALIAN? 42C1AH90 VER. 01.01 DELAY o o o o o o FUNCTION 0 1 3 5 6 7 9 FUNCTION 0 1 3 5 6 7 9 FUNCTION 0 1 3 5 6 7 9 FUNCTION 0 1 3 5 6 7 9 RESET WINDOW 02min? DELAY 05min?