Proteco PTP45 Instructions Manual

Technical data 2.3 Kit content 3. INSTALLATION 3.1 Preliminary checks 3.2 Motor/Tubular assembly 3.3 Wiring Limit switch in closing Limit switch in opening 2.4 Dimensions 3.5 Awnings COMPLIANCE DECLARATION 3.4 Limit switch setting 4. WARRANTY 5. MAINTENANCE 6. DISPOSAL 2.2 Selection guide

Always cut off the power supply before performing any type of intervention. Always make sure the gearmotor is properly connected to the earth Use and installa�on of the product must comply with Machinery Direc�ve 2006/42/CE. Installa�on must be carried out by expert qualified personnel who knows the poten�al hazards associated and in full compliance with current regula�ons. Use of the product must be restricted to its intended use. Any other use is to be considered dangerous and therefore forbidden. Do not allow children to play with the fixed command devices, or in the gate’s area of operation. Keep the gate and the gate opener regularly maintained. Use only Proteco’s original spares. Users are strictly forbidden to carry out any changes on the gate operator. Proteco Cancelli Automa�ci Srl is not liable for any damage resul�ng from improper, wrongful or unreasonable use. 1 1. SAFETY INSTRUCTIONS Important safety instruc�ons for people, this product must only be used for its intended purpose. Any other use is dangerous. Follow all instruc�ons as improper installa�on may result in in serious bodily injury. Keep these warnings together with the installa�on and opera�on manuals that come with the gearmotor. Keep any remote control devices (i.e. transmitters) away from children, to prevent the gearmotor from being accidentally activated CE COMPLIANCE DECLARATION Manufacturer: PROTECO S.r.l. Address: Via Neive, 77 – 12050 Castagnito (CN) – ITALIA declares that The product type: PTP45 tubular motor for rolling shutters and awnings Modelli: PTP45 20, PTP45 30, PTP45 50, PTP45 50M It complies with the essential requirements of EEC Directives: 2006/95/EC Low Voltage Directive 2004/108/EC Electromagnetic Compatibility Directive The product also complies, with the constraints of the applicable parts, with the following standards: EN 55014-1 EN 55014-2 EN 60335-1: 2002+A1+A11+A12+A2+A13 EN 60335-2-97:2006+A11 EN 61000-3-2 EN 61000-3-3 The manufacturer declares that the start-up of the machinery is not permitted unless the machine has been identified and declared as conformed to 2006/42/EC Machinery Directive. Castagnito, October 1st 2015 Marco Gallo Amministratore Delegato

MAX m² PTP45 30 PTP45 50 N.A. 12,5Kg/m² PTP45 20 50 13 244 1,06 3,30 620 50 13 244 1,06 2,40 480 30 17 226 0,95 2,35 480 20 17 155 0,68 2,30 440 The PTP45 range is designed to automate blinds and awnings. 2.1 TECHNICAL FEATURES 2 2. DESCRIPTION AND INTENDED USE PTP4520 Nm rpm W A Kg mm Thrust Motor Speed Motor Power Current Weight Length PTP4530 PTP4550 PTP4550M 2.2 SELECTION GUIDE Surface calculation: height x width = select the model according to the table below m 2 Wood and armored Steel PVC and light Aluminium Extruded Aluminium and Steel MATERIAL Model Nm Max Li�ing Ø70 mm tubolar motors Intersect the value of the extension with the number of arms of the awning EXTENSION OF ARMS N° ARMS

PTP45 50M 1 2 3 4 1 2 3 4 5 2.4 DIMENSIONS 3 2.3 KIT CONTENT PTP 45 (without emergency release) 1 2 3 4 5 6 7 PTP 45 M (with emergency release) 01 02 03 04 n°1 n°1 n°1 n°1 Tubular motor Limit switch adjuster wrench Split pin Wall fixing support 01 02 03 04 05 n°1 n°1 n°1 n°1 n°1 Tubular motor Limit switch adjuster wrench Wall fixing support Split pin Release key

remove all devices for manual opera�on. Make sure the command keys are posi�oned where the system can be visible during opera�on and at least at an height of 1,5 m from ground. 3.1 PRELIMINARY CHECKS If you need to replace an exis�ng system, keep the same axis 1- Low down the roller blind and disconnect it from the tubular 2- Remove the axis RECOMMENDED TOOLS: 4 3. INSTALLATION

Measure the distance between the two supports. Fit the 60 mm adapter in for the whole length �ll covering the locking ring of the limit switch. . The length of the adapter must be such to get the total length (L) as shown in the below picture, keeping a clearance of 2-3 mm. In order to check the correct posi�on and to simulate the final installa�on, lay temporarily the support to the wall as shown in the picture. Simulate the preassembled automa�on, respec�ng the alignment between the two fixing supports and check that the adapter is on level. Mark the holes of the fixing support in a way to get easy access to both fixing screws. Proceed to fix the support to wall. Complete the assembling locking the system with the provided split pin. L 5 Wall fxing support

in downward posi�on. . 3.3 WIRING . Wire the system according to the below diagram: To be up to safety standards we recommend to fit a power cut device, keeping a minimum distance of 3 mm between the contacts. Every motor has to have its own device. WIRES KEY: 1 BLACK 2 BROWN 3 BLUE(Common) 4 YELLOW/GREEN If you wish to install the motor at your right, just switch the black wire with the brown. It’s always wise to double check the wiring: if the rota�on should not proper, just switch the posi�on between the black and the brown wires. 3.4 LIMIT SWITCH SETTING 3.4.1 LIMIT SWITCH IN CLOSING Before fi�ng the store/awning to the octagonal adapter, let the motor run down �ll reaching the expected end stop posi�on. Then fit the store. 6 Wiring diagram for motor installed at your left OPEN/CLOSE OPEN

Give an opening command. Check the store opera�on and make the according adjustments if necessary. To set the limit switch, plug the provided key into the according fixing points. If you wish to increase the run of the store/awning, turn to “+”, while if you wish to decrease it turn to “-“. The below diagrams show how to adjust the available systems, opening se�ng (possible adjustments for motor RH and LF posi�oned): A�er fixing the opening and closing posi�ons, test the store/awning opera�on to check the correct run. Any further adjustments shall be carried out by the provided hexagonal key. 3.5 AWNINGS Ø 70 adapters are available for awnings. Item code MTPR01. So far the assembly a�end the awning manufacturer’s instruc�ons. So far the wiring and limit switch adjustment a�end the store installa�on manual. PROTECO Srl is liable for any manufacture fault on tubular motors, electrical components and accessories during 3 years from manufacture date. PROTECO Srl responds for repairing within the warranty terms, a�er inspec�on by its technical staff. The returned faulty system will remain a Proteco’s property. Use of the product must be restricted to its intended use. Any other use shall be considered out of the warranty. Installa�on and maintenance are charged at the person who carries out the installa�on. Use only Proteco’s original spares. Users are strictly forbidden to carry out any changes on the system. PROTECO Srl is not liable for any damage resul�ng from improper, wrongful or unreasonable use. The return costs are at customer’s charge. PROTECO Srl Via Neive 77, 12050 Castagnito (CN) Italia The warranty doesn’t respond when: 7 4. WARRANTY The chosen system doesn’t comply with the features of the store or awning Prescrip�ons contained into the installa�on manual are disrespected The item has been used/stored in unproper condi�ons The item has been repaired, modified, altered The item has been wrongly used or neglected The manufacture label is damaged or is missing The bad opera�on is due to oxida�on, overvoltage, insects, animals

of the anchoring screws on the operator as well as the good opera�on of all safety devices. 6. DISPOSAL DO NOT DISPOSE OF IN NATURE! Some components may contain hazardous waste. They must, thus, be removed and turned into licensed firms for their disposal. Before ac�ng always check the local laws on the ma�er. 8