SImx ELITE LED LHTC637 Installation Instructions

ensure the desired location does not exceed that rating. Do not install this light in any location where the ambient temperature is likely to exceed 45°C. It is designed for wall mount installation only, with optimum performance when mounted to a solid wall between 1.4 – 1.9 metres above the ground. ELITE LED - PIR Bulkhead INSTALLATION INSTRUCTIONS This product is suitable for use only with a supply voltage of 220-240V AC 50Hz. All electrical work must be carried out in accordance with local and national electrical codes as applicable. We strongly recommend that this light fitting is installed by a registered electrician. Always switch power off prior to installation. A means of mains power isolation must be installed on the circuit for the purpose of safe access for any internal cleaning or maintenance. This light fitting is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the appliance. Any changes or modifications made or attempted to this product, without the prior written approval of the manufacturer, will void any and all stated warranties. IMPORTANT ! Voltage: 220 - 240VAC 50Hz Detection Range: 12 metres Detection Angle: 120° Time Setting: 5 sec to 15 mins Dusk Control: Day to Night (adjustable) Rated Load: 16W max, 2 watts min Luminous Flux: 1390 lumens initial Ingress Protection: Rated to IP55 Construction: Polycarbonate cover with alloy base Warranty: 3 Years Thank you for purchasing this SIMX bulkhead. This light is suitable for outdoor use and requires a 220 – 240V AC power supply. Please read this manual thoroughly before use and retain for future reference. Model Description LHT0337 ELITE LED 16W PIR PORTRAIT BLACK LHT0338 ELITE LED 16W PIR PORTRAIT WHITE LHT0339 ELITE LED 16W PIR LANDSCAPE BLACK LHT0340 ELITE LED 16W PIR LANDSCAPE WHITE LHT0337 BLACK LHT0338 WHITE LHT0339 BLACK LHT0340 WHITE Ph: +64 9 259 1660 | Technical Support Ph: +64 9 259 1662 Email: [email protected] | www.simx.co.nz PUB1347 iss01 07/15 Simx reserves the right to alter technical specifications without prior warning This product is guaranteed by SIMX Ltd for 36 MONTHS from the date of purchase against faulty materials or workmanship which affects its designed ability to switch and operate. During this period if the product has a defect of this nature it will be repaired or replaced free of charge by SIMX with the same item, or a similar item, or a similar one of higher specification. ON CONDITION THAT: The buyer returns it to the seller from whom it was bought, freight paid. The product has been bought by the user i.e. a receipt/sales invoice is produced as proof of purchase. The product has not been misused or handled carelessly, installed in anyway contrary to the installation instructions, or installed in any unusually exposed or harsh environmental conditions. This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable parts. It does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. Our Goods come with guarantees that cannot be excluded under the Australian and New Zealand Consumer law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if the Goods fail to be of acceptable quality and the failure does not amount to a major failure. MANUFACTURERS EXTENDED WARRANTY

Warning: Isolate the power supply before installation. • Release the front fascia of the light, by inserting a flat head screwdriver into the two tabs at the base of the fitting and gently turn these. Remove the front facia. • Unscrew and remove the small connection cover on the front of the fitting. • Position the unit against wall in the desired location, ensuring the power supply cable can easily enter the fitting through the rubber grommet at the rear of the fitting. • Use the holes in each corner of the fitting to mark the 4 drill holes required to secure the base to the wall (and mark the cable inlet location if required). • Drill the wall and fit the wall plugs supplied. • Use a sharp knife to cut a small ‘X’ in the rubber grommet and feed the power supply cable through into the light fitting. Note: Please ensure the cable enters the grommet from beneath to avoid moisture migration. • The light fitting can now be fixed to the wall using the mounting screws provided. • Strip cable insulation 6mm and attach to the terminal block following the label denotations. • After the wiring is secured, the PIR controls should be set and tested, as described in ‘DAYTIME Walk Test’ on the following page. • Once this is done, and changes are no longer required, replace the small connection cover securely, and refit the front fascia, using the double-sided tape (supplied) between the fascia and the opal lens for more permanent fixing. ELITE LED PIR Bulkhead is a Class 1 fitting and therefore needs to be Earthed for electrical safety. Waterproof cable should be used for outdoor installations. Using Twin and Earth 3 core round flexible cable at least 1mm² gauge is preferred. Avoid directing the PIR sensor towards objects that may move in the wind, such as shrubs or trees, or at highly reflective surfaces. Avoid positioning the light fitting near heat sources, such as hot ventilator ducts, air conditioning units, exhaust outlets, street lighting or traffic, all of which may interfere with PIR operation. Note that a PIR sensor is more sensitive to a heat source moving across its coverage area, and less sensitive to a heat source that moves directly towards the PIR. This PIR operates on P-LUX technology, providing a continuous low level courtesy light from dusk to dawn, powering up to full light output when presence detection is made. Low level output is max 2 watts. Once the fitting is electrically connected, it requires approx. 60 sec to warm up. During this time the light will switch on for a short time then turn itself off. Do not commence any walk tests until this time has elapsed. Dials on the P-LUX rotate clockwise or anti-clockwise and should be turned GENTLY using a flat head screwdriver. LUX adjustment Dial marked ‘L’ sets the acceptable amount of light present before the unit will activate. At the lowest level it operates only at maximum darkness, at highest level it operates both day and night. Set to desired activation point depending on the needs of the installation. TIME adjustment Dial marked ‘T’ has a minimum setting of approx. 5sec and a maximum setting of approx. 5min. This adjusts to the preferred duration the light activates for when it last detects movement. The timer will restart each time the sensor detects any new movement. RANGE adjustment Dial marked ‘R’ alters the PIR range of detection and the amount of infra-red radiation (heat) required to trigger the PIR. To be effective but keep nuisance tripping to a minimum, it is advised to turn the range control to the middle position where the ambient temperature is between 15⁰-20⁰C. This range sensitivity adjustment can also be used to compensate for changes in outside air temperature in Winter (set lower) and Summer (set higher). For DAYTIME walk testing: Turn the TIME dial marked ‘T’ fully anti-clockwise to minimum setting, and the LUX control dial marked ‘L’ fully clockwise to maximum setting. Turn on the power to the light. The light should light up for approx. 15 sec then dim down until the PIR is activated again, when it will again revert to full power. Use this setting for walk testing the unit to understand the detection zone, and adjust the RANGE control marked ‘R’ to suit your location. Once this is set, readjust TIME and LUX to suit your needs, then reassemble the fitting. Care and consideration should be taken when this unit is located close to property boundaries, to avoid unnecessary spill light or glare to neighbours, and to avoid unwanted activation of the PIR by passing pedestrians or vehicles. ELECTRICAL INSTALLATION INSTALLING YOUR ELITE PIR BULKHEAD L N E RANGE TIME LUX PIR Setting Controls SENSOR CALIBRATION