WHITECROFT LIGHTING Mini Spot 65 Installation Leaflet

connection to mains wiring. 2. Ensure that the rated voltage and frequency requirements are compatible with the available mains supply. 3. Cleaning of reflectors and lenses should be carried out using clean, soft and lint free cloths and anti-static cleaning fluid. 4. Do not carry out high voltage insulation test, i.e. 500/1000v this may damage internal components. 5. This product is class 2 insulated and so does not require an earth connection. 6. Some luminaires installed in outdoor environments may experience a build-up of internal condensation. This is due to a difference in temperature between inside and outside the luminaire which is quite common and acceptable under BSEN60598. 7. Replacing the light source within this luminaire shall only be carried out by the manufacturer, service agent or a similar qualified person. Please note: All images shown are for illustration purposes and should be used as a reference guide only Whitecroft Lighting Limited Burlington Street, Ashton-under-Lyne, Lancashire OL7 0AX Telephone +44 (0)870 5 087 087 Facsimile: +44 (0)870 5 084 210 Registered No. 3848973 England Registered Office: As above PKLEAFMINSPOT65 TECHNICAL SUPPORT Tel: 0161 331 5700 e-mail: [email protected] www.whitecroftlighting.com Mini Spot 65 Installation Leaflet Mar 2016 - Rev B SPECIFICATION Lamp Type: LED Lamp Colour: 4000°K Control Gear: Fixed Output Rating: IP65 Body: Die cast aluminium with cooling fins Diffuser: Tempered 4mm glass Paint Finish: Polyester powder coated Power: 220-240V / 50-60Hz Description Output (Llm) Weight Product Colour Narrow & Wide Beam Spotlight 2100 - 3500 2.7 Kg Silver / Grey Colour Filter Lens N/A 0.1 Kg Blue / Red / Green / Yellow Cowl Accessory N/A 0.3 Kg Black Adjustable Shutter Accessory N/A 0.4 Kg Black Ground Mounting Spike N/A 0.1 Kg Black

All measurements in mm unless stated otherwise 1. Remove the fitting from all of the packaging. Optional To change lens colour: Remove screws on back of lamp housing before releasing standard lens via the holding screws (Fig. 1). Replace standard lens with coloured lens and re-assemble lamp housing. Optional Attaching cowl / shutter accessory: Dissemble lamp housing (see change lens step) and attach cowl or shutter using an Allen key (Fig. 2). Avoid water pooling in cowl by angling luminaire downwards. When fitting accessories ensure small O-rings are not lost 2. Remove the 4 fixing screws securing the luminaire body to the base (Fig. 3). 3. Surface mounting: Secure luminaire base to desired surface in correct orientation using appropriate fixings (by others) via surface mounting holes (Fig. 3). Optional Ground spike mounting: Attach the mounting spike to the base (if specified) using the screws supplied via the spike mounting holes (Fig. 4) and secure the mounting spike into the ground. 4. Feed the 2 core supply flex (Ø 9 min - 12 max) through the grommet (Fig. 5). 5. Strip the correct length of wire and neatly connect the 2 core supply flex to the Live/Neutral (Fig. 5). 6. Re-attach the luminaire body to the base using the 4 fixing screws (Fig. 3) Fig. 4 [ Ground Spike Attachment ] Fig. 1 [ Filter Lens Fitting ] Fig. 2 Shutter Accessory Cowl Accessory [ Shutter / Cowl Fitting ] Fig. 3 156 100 97 Fixing screws Surface mount fixings (by others) [ Luminaire Base Assembly ] Raw plugs (by others) 8 Fig. 5 [ Wire Preparation ] F / N = L / N Adjust light direction using a suitable Allen key ( Angle rotation limited to 280° approx. ) 25