Doyon DP14 Operation & User’s Manual

SAVE THESE INSTRUCTIONS DANGER TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS TABLE OF CONTENTS SECTION «A»DESCRIPTION PAGE Installation and maintenance manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1 Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2 Shipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3 Distances to respect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A6 Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7 For more information, please contact our office: . . . . . . . . . . . . . . . . . . . . A8 SECTION «B» DIMENSIONS DP14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION «E» COMPONENT PARTS Component parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1 E1 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DP14.DOC Rev. 01.2008

INSTALLATION AND MAINTENANCE MANUAL This proofer is manufactured with first quality material by experienced technicians. Proper installation and maintenance will guarantee a reliable service for years to come. A nameplate fixed to the front of the proofer specifies the serial number, model number, number of phase, amperage, voltage and frequency. Drawings, electrical diagram and replacement part numbers are included in this manual. The electrical diagram is affixed in the control panel located on the top of the proofer. ATTENTION DOYON is not responsible for damages to the property or the equipment caused by personnel who is not certified by known organizations. The customer is responsible for finding qualified technicians in electricity and plumbing for the installation of the oven.

You just bought the most advanced proofer in the world, the "DOYON" technology at its best. This proofer is manufactured using the highest quality components and material. The DOYON equipments are designed with parts that are easy to find. S H I P P I N G For your safety, this equipment is verified by qualified technicians and carefully crated before shipment. The freight company assumes full responsibility concerning the delivery in good condition of the equipment in accepting to transport it. IMPORTANT RECEPTION OF THE MERCHANDISE Take care to verify that the received equipment is not damaged before signing the delivery receipt. If a damage or a lost part is noticed, write it clearly on the receipt. If it is noticed after carrier left, contact immediately the freight company in order that they do their inspection. We do not assume the responsibility for damages or losses that may occur during transportation.

FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY APPLIANCE. IMPORTANT INSTALLATION AND SERVICE Installation and service must be done by specialized technicians. Contact a certified electrician and plumber for set up. The proofer must be connected to the utility and electrically grounded in conformity to the effective local regulations. If these are not established, the oven must be connected according to the Canadian Electrical Code (CSA-C22.1-XX) or National Electrical Code (NFPA 70-XX). Refer to last edition year for XX.

• Top of the proofer: a clearance of 12 inches to the ceiling must exist to permit maintenance. • Back and sides: 0 inch clearance. I N S T A L L A T I O N IN GENERAL Take off the packaging material with care. Take off all the material used for packing and accessories. Each unit is set up to be used with the electrical supply specified on the nameplate fixed on the front of the unit. Always LOCK the wheels after installation and use a flexible conduit. 1. To the electrician Electrical supply installation must be in accordance with the electrical rating on the nameplate and use flexible wire. 2. To the plumber MANUAL WATER FILL No water line is required. Water is filled manually in the pan inside the proofer. This equipment is to be installed to comply with the applicable federal, state or local plumbing codes. Connect the steam system (1/4 NPT) to the cold water distribution network. We highly recommend a water softener to eliminate minerals in the water. We suggest to use CUNO # CFS6135 (Doyon part number PLF240).

1. Switch "ON". 2. Set the thermostat control at 100o F. 3. Fill water pan if not automatic and set the humidity control at 4. If there is too much fog and water drips from the glass doors, adjust humidity control to a lower number. 4. When the temperature is stabilized, put the products in the proofer. (Leave them inside until they are ready to bake.) 5. When proofing cycle is completed, turn the switch "OFF". When the proofer is not in operation, open the doors to let out the humidity and then prevent mould. P.S. The doors should not be opened unnecessarily to conserve the heat and humidity in the proofer. Every day cleaning of the water pan under the proofer's doors should be exercised. POWER FAILURE When the power comes back, the proofer will start automatically. Then it is recommended to turn off the unit to avoid it starting without supervision.

ANSWERS TO MOST FREQUENT QUESTIONS Always cut off the main power before replacing any parts. Take care of water piping and electric cable. Control parts on the front. To remove parts from front panels, you have to go on the top of the unit. Control panel, proofer unit and refrigeration unit. They are located on the top. Questions Solutions The unit does not turn on when installed. Check if the light is on. Check if the proofer switch is on. Check the breaker of the building. Check the fuses on the front and in the electrical control panel. The blower runs but the unit does not produce heat. Make sure that the thermostat is adjusted to the desired temperature (over ambient temperature) and the pilot light is lit. The blower runs but the unit does not produce steam. Make sure that the humidity control is set at about 4. Check if you have water in the pan and if the pan is sit properly on the element.

Step by step Recommendations Clean the inside of the unit with water and soap. We recommend and sell: Dirt Buster III : Action foam cleaner CHEMCO Part number : NEB201 Clean the unit exterior with a stainless steel polish. We recommend and sell: Stainless steel cleaner SANY or CURTIS (comestible) Part number : NES201 CAUTION Save these instructions.

PLEASE CONTACT OUR OFFICE : DOYON EQUIPMENT INC. 1255, rue Principale Linière, Qc, Canada G0M 1J0 Tel. : 1 (418) 685-3431 Canada : 1 (800) 463-1636 U.S. : 1 (800) 463-4273 FAX : 1 (418) 685-3948 Internet: www.doyon.qc.ca E-Mail : [email protected]

1 AND ELT620 THERMOSTAT BEZEL 1 2 ELL650 RED PILOT LIGHT 2 3 ELI230 INFINITY SWITCH 240V (HUMIDITY CONT.) 1 AND ELI240 INFINITY SWITCH KNOB 1 4 ELI550 MAIN SWITCH (SELECTOR) 1 AND ELI555 CONTACT BLOCK 1NO 1 AND ELI556 ON - OFF PLATE 1 5 ELB096 5A BREAKER 1 6 QUP465 DOOR HANDLE STAINLESS TUBING 2 7 VT1251 TEMPERED GLASS 5 MM 12" X 51 3/4" 2 AND MBAV1921 ALUMINIUM DOOR EXTRUSION 2 8 QUP320 DOOR HINGE 4 9 QUA200 DOOR MAGNET 2 10 STP500 STAINLESS STEEL WATER PAN FOR BOTTOM DOOR 1 11 REEF10 STAINLESS STEEL WATER PAN 1 12 ELE185 ELEMENT (CIRCULAR) 120V 1250W FOR PROOFER 1 Model : DP14 View : FRONT & SIDE

1 2 ELE130 COIL ELEMENT 120V 1500W 1 3 ELB072 TERMINAL BLOCK 3P 175A 1 4 ELL050 GROUND LUG 1 5 ELC860 CONTACTOR 2P 30A 110V 1 6 ELT505 HIGH LIMIT TEMPERATURE 300° 1 Model : DP14 View:

Doyon Equipment Inc. guarantees to the original purchaser only that its product are free of defects in material and workmanship, under normal use. This warranty does not cover any light bulbs, thermostat calibration or defects due to or resulting from handling, abuse, misuse, nor shall it extend to any unit from which the serial number has been removed or altered, or modifications made by unauthorized service personnel or damage by flood, fire or other acts of God. Nor will this warranty apply as regards to the immersion element damaged by hard water. The extent of the manufacturer’s obligation under this warranty shall be limited to the replacement or repair of defective parts within the warranty period. The decision of the acceptance of the warranty will be made by Doyon Equipment service department, which decision will be final. The purchaser is responsible for having the equipment properly installed, operated under normal conditions with proper supervision and to perform periodic preventive maintenance. If any parts are proven defective during the period of one year from date of purchase, Doyon Equipment Inc. hereby guarantees to replace, without charge, F.O.B. Linière, Quebec, Canada, such part or parts. Doyon Equipment Inc will pay the reasonable labor charges in connection with the replacement parts occurring within one year from purchase date. Travel over 50 miles, holiday or overtime charges are not covered. After one year from purchase date, all labor and transportation charges in connection with replacement parts will be the purchaser’s responsibility. Doyon Equipment Inc. does hereby exclude and shall not be liable to purchaser for any consequential or incidental damages including, but not limited to, damages to property, damages for loss of use, loss of time, loss of profits or income, resulting from any breach or warranty. In no case, shall this warranty apply outside Canada and continental United States unless the purchaser has a written agreement from Doyon Equipment Inc.