Siemens SIMATIC NET Installation Manual

RUGGEDCOM RS8000T https://www.siemens.com

RUGGEDCOM RS8000T Installation Manual Preface Introduction 1 Installing the Device 2 Device Management 3 Communication Ports 4 Technical Specifications 5 Certification 6 01/2021 C79000-G8976-1023-05

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper Use of Siemens Products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Digital Industry Process Automation Postfach 48 48 90026 NÜRNBERG GERMANY © 01/2021 Subject to Change Copyright © Siemens 2021 All rights reserved

Preface ............................................................................................................................................ v Related Documents ................................................................................................................. v Accessing Documentation ....................................................................................................... v Registered Trademarks ............................................................................................................ v Warranty ................................................................................................................................. v Training .................................................................................................................................. vi Customer Support .................................................................................................................. vi Contacting Siemens ............................................................................................................... vii 1 Introduction ........................................................................................................................... 1 1.1 Feature Highlights ................................................................................................. 1 1.2 Description ............................................................................................................ 2 1.3 Required Tools and Materials ................................................................................. 4 1.4 Decommissioning and Disposal ............................................................................. 4 1.5 Cabling Recommendations .................................................................................... 4 1.5.1 Supported Fiber Optic Cables ................................................................................ 5 2 Installing the Device ............................................................................................................. 7 2.1 Mounting the Device ............................................................................................. 7 2.1.1 Mounting the Device on a DIN Rail ........................................................................ 8 2.1.2 Mounting the Device to a Rack .............................................................................. 9 2.1.3 Mounting the Device to a Panel .......................................................................... 11 2.2 Connecting the Failsafe Alarm Relay .................................................................... 11 2.3 Connecting Power ............................................................................................... 12 2.3.1 Connecting AC Power .......................................................................................... 13 2.3.2 Connecting DC Power ......................................................................................... 14 3 Device Management ........................................................................................................... 17 3.1 Connecting to the Device .................................................................................... 17 3.2 Configuring the Device ........................................................................................ 18 3.3 Resetting the Device ........................................................................................... 18 4 Communication Ports .......................................................................................................... 19 4.1 Copper Ethernet Ports ......................................................................................... 19 4.2 Fiber Optic Ethernet Ports ................................................................................... 20 5 Technical Specifications ...................................................................................................... 21 5.1 Power Supply Specifications ................................................................................ 21 5.2 Failsafe Relay Specifications ................................................................................ 21 5.3 Copper Ethernet Port Specifications ..................................................................... 21 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 iii

5.4 Fiber Optic Ethernet Port Specifications ............................................................... 22 5.5 Operating Environment ....................................................................................... 22 5.6 Mechanical Specifications .................................................................................... 22 5.7 Dimension Drawings ........................................................................................... 22 6 Certification ......................................................................................................................... 25 6.1 Approvals ............................................................................................................ 25 6.1.1 CSA ..................................................................................................................... 25 6.1.2 European Union (EU) .......................................................................................... 25 6.1.3 FCC ..................................................................................................................... 26 6.1.4 ISO ...................................................................................................................... 26 6.1.5 ACMA .................................................................................................................. 26 6.1.6 RoHS ................................................................................................................... 27 6.2 EMC and Environmental Type Tests ..................................................................... 27 iv RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

major features of the device, installation, commissioning and important technical specifications. It is intended for use by network technical support personnel who are responsible for the installation, commissioning and maintenance of the device. It is also recommended for use by network and system planners, system programmers, and line technicians. Related Documents Other documents that may be of interest include: Document Title Link RUGGEDCOM ROS Configuration Manual https://support.industry.siemens.com/cs/ww/en/ view/109737246 Accessing Documentation The latest user documentation for RUGGEDCOM RS8000T is available online at https://support.industry.siemens.com . To request or inquire about a user document, contact Siemens Customer Support. Registered Trademarks RUGGEDCOM ™ and ROS™ are trademarks of Siemens AG. Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the owner. Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. The warranties set forth in this article are exclusive and are in lieu of all other warranties, performance guarantees and conditions whether written or oral, statutory, express or implied (including all warranties and conditions of merchantability and fitness for a particular purpose, and all warranties and conditions arising from course of dealing or usage RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 v

provided above shall constitute the Seller’s sole liability and the Customer’s exclusive remedy for defective or nonconforming goods or services whether claims of the Customer are based in contract (including fundamental breach), in tort (including negligence and strict liability) or otherwise. For warranty details, visit https://www.siemens.com or contact a Siemens customer service representative. Training Siemens offers a wide range of educational services ranging from in-house training of standard courses on networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs, experience and application. Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make sure users have the right knowledge and expertise to understand the various technologies associated with critical communications network infrastructure technologies. Siemens ' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility, transportation and industrial markets, allows Siemens to provide training specific to the customer's application. For more information about training services and course availability, visit https:// www.siemens.com or contact a Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request to submit a Support Request (SR) or check on the status of an existing SR. Telephone Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en. Mobile App Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to: • Access Siemens' extensive library of support documentation, including FAQs and manuals • Submit SRs or check on the status of an existing SR vi RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

Training, etc. • Ask questions or share knowledge with fellow Siemens customers and the support community Contacting Siemens Address Siemens AG Industry Sector 300 Applewood Crescent Concord, Ontario Canada, L4K 5C7 Telephone Toll-free: 1 888 264 0006 Tel: +1 905 856 5288 Fax: +1 905 856 1995 E-Mail [email protected] Web https://www.siemens.com RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 vii

managed, Ethernet switches specifically designed to operate reliably in electrically and environmentally harsh environments. The RUGGEDCOM RS8000T model provides IEEE 1613 Class 2 error-free communications performance under EMI stress. An operating temperature range of -40 to 85 °C (-40 to 185 °F) allows the RUGGEDCOM RS8000T to be placed in almost any location. The RUGGEDCOM RS8000T provides a wide range of power supply options suitable for multiple industries and for worldwide operability. Options include 24 VDC, 48 VDC, and HI (88-300 VDC or 85-264 VAC) The RUGGEDCOM RS8000T offers advanced Layer 2 and 3 networking features and network management via the Rugged Operating System (ROS). A unique feature of ROS is the performance of its IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) used for implementing fault tolerant ring and mesh network architectures. The protocol has been optimized to support ring sizes of up to 160 switches and fault recovery times in the order of less than 5 ms per switch. The RUGGEDCOM RS8000T’s superior ruggedized design coupled with the Rugged Operating System (ROS) provides improved system reliability and advanced networking features making it ideally suited for creating Ethernet networks for mission-critical, real-time control applications. 1.1 Feature Highlights Ethernet Ports • Six 10/100Base-TX and two 100Base-FX ports • Multi-mode and single-mode optical transceivers • Industry standard fiber optical connectors: MTRJ, LC Rated for Reliability in Harsh Environments • Immunity to EMI and heavy electrical surges • Meets IEEE 1613 Class 2 (electric utility substations) • Exceeds IEC 61850-3 (electric utility substations) • Exceeds IEC 61800-3 (variable speed drive systems) • Exceeds IEC 61000-6-2 (generic industrial) • Exceeds NEMA TS-2 (traffic control equipment) RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 1

• Failsafe Output Relay: For critical failure or error alarming • Conformal coated printed circuit boards (optional) Cyber Security Features • Multi-level user passwords • SSH/SSL (128-bit encryption) • Enable/disable ports, MAC based port security • Port based network access control (802.1x) • VLAN (802.1Q) to segregate and secure network traffic • RADIUS centralized password management • SNMPv3 authentication and 56-bit encryption Management Tools • Web-based, Telnet, CLI management interfaces • SNMP v1/v2/v3 (56-bit encryption) • Remote Monitoring (RMON) • Rich set of diagnostics with logging and alarms Universal Power Supply Options • Universal high-voltage range: 88-300 VDC or 85-264 VAC • Popular low voltage ranges: 24 VDC (10-36 VDC), 48 VDC (36-59 VDC) • Terminal blocks for reliable maintenance free connections • CSA/UL 60950 safety approved to 85 °C (185 °F) 1.2 Description The RUGGEDCOM RS8000T features various ports, controls and indicator LEDs on the front and rear panels for configuring and troubleshooting the device. 2 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

5 RS232 Serial Console Port (DB9) Figure 1.1 Front and Rear Panels POWER LED Illuminates when power is being supplied to the device. Color Description Green Device ready Off No power RESET Button Shuts down and restarts the device. For more information, refer to "Resetting the Device (Page 18)". Port Status Indicator LEDs These LEDs indicate when serial ports are active. LED State Meaning Solid Link detected Link Off No link detected Blinking Link activity (receiving) RX Off No link activity Blinking Link activity (transmitting) TX Off No link activity RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 3

RS232 Serial Console Port The serial console port is for interfacing directly with the device and accessing initial management functions. For information about connecting to the device via the serial console port, refer to "Connecting to the Device (Page 17)". Communication Ports Receive and transmit data. For more information about the various ports available for the RUGGEDCOM RS8000T, refer to "Communication Ports (Page 19)". 1.3 Required Tools and Materials The following tools and materials are required to install the RUGGEDCOM RS8000T: Tools/Materials Purpose AC or DC power cord (16 AWG) For connecting power to the device. CAT-5 Ethernet cables For connecting the device to the network. Flathead screwdriver For mounting the device to a DIN rail. Phillips screwdriver For mounting the device to a panel. 4 x #8-32 screws For mounting the device to a panel. 1.4 Decommissioning and Disposal Proper decommissioning and disposal of this device is important to prevent malicious users from obtaining proprietary information and to protect the environment. Decommissioning This device may include sensitive, proprietary data. Before taking the device out of service, either permanently or for maintenance by a third-party, make sure it has been fully decommissioned. For more information, refer to the associated Configuration Manual. Recycling and Disposal For environmentally friendly recycling and disposal of this device and related accessories, contact a facility certified to dispose of waste electrical and electronic equipment. Recycling and disposal must be done in accordance with local regulations. 1.5 Cabling Recommendations All copper Ethernet ports on RUGGEDCOM products include transient suppression circuitry to protect against damage from electrical transients and conform with IEC 61850-3 and IEEE 1613 Class 1 standards. This means that during a transient 4 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

electrical event, communications errors or interruptions may occur, but recovery is automatic. Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions. 1.5.1 Supported Fiber Optic Cables The following fiber optic cable types are supported under the stated conditions. Distance (m) Cable Type Wavelength (nm) Modal Bandwidth (MHz·km) 100Base-FX 1000Base-SX 10GBase-SR 850 200 — 275 33 OM1 (62.5/125) 1300 500 2000 — — 850 500 — 550 82 OM2 (50/125) 1300 500 2000 — — 850 1500 — 550 300 OM3 (50/125)a 1300 500 2000 — — 850 3500 — 550 400 OM4 (50/125)a 1300 500 2000 — — a Laser optimized. RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 5

6 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

2 This chapter describes how to install the device, including mounting the device, connecting power, and connecting the device to the network. DANGER Electrocution hazard – risk of serious personal injury and/or damage to equipment Before performing any maintenance tasks, make sure all power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate. IMPORTANT This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens AG could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment. IMPORTANT This product should be installed in a restricted access location where access can only be gained by authorized personnel who have been informed of the restrictions and any precautions that must be taken. Access must only be possible through the use of a tool, lock and key, or other means of security, and controlled by the authority responsible for the location. 2.1 Mounting the Device The RUGGEDCOM RS8000T is designed for maximum mounting and display flexibility. It can be equipped with connectors that allow it to be installed in a 48 cm (19 in) rack, 35 mm (1.4 in) DIN rail, or directly on a panel. IMPORTANT Heat generated by the device is channeled outwards from the enclosure. As such, it is recommended that 2.5 cm (1 in) of space be maintained on all open sides of the device to allow for some convectional airflow. Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient temperature and improve the long-term reliability of all equipment mounted in the rack space. RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 7

2.1.1 Mounting the Device on a DIN Rail Note For detailed dimensions of the device with either rack, DIN rail or panel hardware installed, refer to "Dimension Drawings (Page 22)". 2.1.1 Mounting the Device on a DIN Rail The RUGGEDCOM RS8000T can be ordered with a panel/DIN rail adapter preinstalled on the back of the chassis. Use the adapter to mount the device to a standard 35 mm (1.4 in)IEC/EN 60715 or TS35 DIN rail. Mounting the Device To mount the device to a DIN rail, do the following: 1. Hook the top teeth of the adapter onto the DIN rail. Note The adapter features a sliding release with a slot at the bottom for a flathead screwdriver. 1 2 3 1 1 2 1 DIN Rail 2 Panel/DIN Rail Adaptor Figure 2.1 Mounting the Device to a DIN Rail 2. Insert a flathead screwdriver into the slot of the sliding release and move it down. 3. Push the device against the bottom of the DIN rail, then let go of the sliding release to latch the device. 8 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

2.1.2 Mounting the Device to a Rack Removing the Device To remove the device from a DIN rail, do the following: 1. Insert a flathead screwdriver into the slot of the sliding release and move it down. 1 3 2 1 2 1 1 DIN Rail 2 DIN Rail Adapter Figure 2.2 Removing the Device from a DIN Rail 2. Swing the bottom of the device away from the DIN rail. 3. Lift the device off the DIN rail. 2.1.2 Mounting the Device to a Rack To secure the device to a standard 48 cm (19 in) rack, do the following: 1. Remove the four screws from the side of the device. RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 9

2.1.2 Mounting the Device to a Rack 2. Insert the device into rack mount adapter and use the screws to secure it. Note The device can be installed with the communication ports facing the front or rear of the rack, depending on the desired orientation. 2 1 1 Rack Mount Adapter 2 Screw Figure 2.3 Rack Mounting 3. Insert the rack mount adapter and device assembly into the rack. Note Since heat within the device is channelled to the enclosure, it is recommended that 1 rack-unit of space, or 44 mm (1.75 in), be kept empty above the device. This allows a small amount of convectional airflow. Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient temperature and improve the long-term reliability of all equipment mounted in the rack space. 4. Secure the adapter to the rack using the supplied hardware. 10 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

2.1.3 Mounting the Device to a Panel 2.1.3 Mounting the Device to a Panel To mount the device to a panel, do the following: 1. Place the device against the panel and align the adapters with the mounting holes. 2 1 1 1 1 2 1 Screw 2 Panel/DIN Rail Adaptor Figure 2.4 Panel Mounting 2. Install the supplied screws to secure the adapters to the panel. 2.2 Connecting the Failsafe Alarm Relay The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm is configured, the relay opens the NO contact and closes the NC (Normally Closed) contact. Note Control of the failsafe relay output is configurable through RUGGEDCOM ROS . One common application for this relay is to signal an alarm if a power failure occurs. For RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 11

2.3 Connecting Power more information, refer to the RUGGEDCOM RS8000T Configuration Manual for the RUGGEDCOM RS8000T. The following shows the proper relay connections. 1 2 3 1 Normally Closed 2 Common 3 Normally Open Figure 2.5 Failsafe Alarm Relay Wiring 2.3 Connecting Power The RUGGEDCOM RS8000T supports a single integrated high AC/DC or low DC power supply IMPORTANT • For 88-300 VDC rated equipment, an appropriately rated circuit breaker must be installed. • For 100-240 VAC rated equipment, an appropriately rated circuit breaker must be installed. • Use minimum #16 gage wiring when connecting terminal blocks. • A circuit breaker is not required for 12, 24 or 48 VDC rated equipment. • Power input terminals have reverse polarity protection for 12, 24 and 48 VDC rated equipment. • Equipment must be installed according to applicable local wiring codes and standards. 12 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

2.3.1 Connecting AC Power 2.3.1 Connecting AC Power To connect a high AC power supply to the device, do the following: NOTICE Electrical hazard – risk of damage to equipment Before testing the dielectric strength (HIPOT) in the field, remove the braided ground cable connected to the surge ground terminal and chassis ground. This cable connects transient suppression circuitry to chassis ground and must be removed in order to avoid damage to transient suppression circuitry during testing. 1. Connect the positive wire from the power source to the positive/hot (+/H) terminal on the terminal block. 4 1 2 3 1 Positive/Hot (+/H) Terminal 2 Negative/Neutral (-/N) Terminal 3 Surge Ground Terminal 4 Braided Ground Cable Figure 2.6 Terminal Block Wiring 2. Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block. 3. Using a braided wire or other appropriate grounding wire, connect the surge ground terminal to the chassis ground connection. The surge ground terminal is used as the ground conductor for all surge and transient suppression circuitry internal to the unit. RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 13

2.3.2 Connecting DC Power 4. Using a #6 ring lug and #6-32 screw, secure the ground terminal on the power source to the chassis ground terminal on the device. Make sure the lug is tightened to 1.7 N·m (15 lbf·in). 2 1 3 1 Stainless Steel Stud 2 #6-32 Screw 3 #6 Ring Lug Figure 2.7 Chassis Ground Connection 2.3.2 Connecting DC Power To connect a high or low DC power supply to the device, do the following: NOTICE Electrical hazard – risk of damage to equipment Before testing the dielectric strength (HIPOT) in the field, remove the braided ground cable connected to the surge ground terminal and chassis ground. This cable connects transient suppression circuitry to chassis ground and must be removed in order to avoid damage to transient suppression circuitry during testing. 14 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

2.3.2 Connecting DC Power 1. Connect the positive wire from the power source to the positive/hot (+/L) terminal on the terminal block. 4 1 2 3 1 Positive/Hot (+/L) Terminal 2 Negative/Neutral (-/N) Terminal 3 Surge Ground Terminal 4 Braided Ground Cable Figure 2.8 Terminal Block Wiring 2. Connect the negative wire from the power source to the negative/neutral (-/N) on the terminal block. 3. Using a braided wire or other appropriate grounding wire, connect the surge ground terminal to the chassis ground connection. The surge ground terminal is used as the ground conductor for all surge and transient suppression circuitry internal to the unit. 4. Using a #6 ring lug and #6-32 screw, secure the ground terminal on the power source to the chassis ground terminal on the device. Make sure the lug is tightened to 1.7 N·m (15 lbf·in). 2 1 3 1 Stainless Steel Stud 2 #6-32 Screw 3 #6 Ring Lug Figure 2.9 Chassis Ground Connection RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 15

2.3.2 Connecting DC Power 16 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

3.1 Connecting to the Device The following describes the various methods for accessing the RUGGEDCOM ROS console and Web interfaces on the device. For more detailed instructions, refer to the RUGGEDCOM RS8000T Configuration Manual for the RUGGEDCOM RS8000T. Serial Console Port Connect a PC or terminal directly to the serial console port to access the boot-time control and RUGGEDCOM ROS console interface. IMPORTANT The serial console port is intended to be used only as temporary connections during initial configuration or troubleshooting. The serial console port implements RS232 DCE (Data Communication Equipment) on a DB9 connector. The following is the pin-out for the port: 5 9 6 1 Figure 3.1 Serial DB9 Console Port Pin Name Description 1 NC No Connection 2 TX Transmit Data 3 RX Receive Data 4 NC No Connection 5 GND Signal Ground 6 NC No Connection 7 NC No Connection 8 NC No Connection 9 NC No Connection Communication Ports Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM RS8000T console and Web interfaces via the device's IP address. For more information about available ports, refer to "Communication Ports (Page 19)". RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 17

3.2 Configuring the Device Once the device is installed and connected to the network, it must be configured. All configuration management is done via the RUGGEDCOM ROS interface. For more information about configuring the device, refer to the RUGGEDCOM RUGGEDCOM RS8000T Configuration Manual associated with the installed software release. 3.3 Resetting the Device The RUGGEDCOM RS8000T can be reset (rebooted) using the RESET button. The RESET button is recessed and can only be reached using a pin or small screwdriver. To reset the device, quickly press and release the RESET button with a pin. 18 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

ports to enhance its abilities and performance. To determine which ports are equipped on the device, refer to the factory data file available through RUGGEDCOM ROS . For more information on how to access the factory data file, refer to the RUGGEDCOM RS8000T Configuration Manual for the RUGGEDCOM RS8000T. Each communication port type has a specific place in the RUGGEDCOM RS8000T chassis. 1 2 1 Ports 1 to 6 2 Ports 7 to 8 Figure 4.1 Port Assignment Port Type 1 to 6 10/100Base-TX 7 to 8 100Base-FX 4.1 Copper Ethernet Ports The RUGGEDCOM RS8000T supports several 10/100Base-TX Ethernet ports that allow connection to standard Category 5 (CAT-5) unshielded twisted-pair (UTP) cables with RJ45 male connectors. The RJ45 connectors are directly connected to the chassis ground on the device and can accept CAT-5 shielded twisted-pair (STP) cables. RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 19

The following is the pin-out for the RJ45 male connector: 1 8 Figure 4.2 RJ45 Ethernet Port Pin Configuration Pin Name Description 1 RX+ Receive Data+ 2 RX- Receive Data- 3 TX+ Transmit Data+ 4 Reserved (Do Not Connect) 5 Reserved (Do Not Connect) 6 TX- Transmit Data- 7 Reserved (Do Not Connect) 8 Reserved (Do Not Connect) Case Shield (Chassis Ground) For specifications on the available copper Ethernet ports, refer to "Copper Ethernet Port Specifications (Page 21)". 4.2 Fiber Optic Ethernet Ports Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Registered Jack) or LC (Lucent Connector) connectors. Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. 2 1 1 Tx Connector 2 Rx Connector Figure 4.3 MTRJ Port 2 1 1 Tx Connector 2 Rx Connector Figure 4.4 LC Port For specifications on the available fiber optic Ethernet ports, refer to "Fiber Optic Ethernet Port Specifications (Page 22)". 20 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

5.1 Power Supply Specifications Input Range Power Supply Type Minimum Maximum Internal Fuse Ratinga b Maximum Power Consumptionc 12-24 VDC 10 VDC 36 VDC 6.3 A(F) 24 VDC 18 VDC 36 VDC 5 A(F) 48 VDC 36 VDC 59 VDC 3.15 A(T) HI (125/250 VDC)d 88 VDC 300 VDC 3.15 A(T) HI (110/230 VAC)d 85 VAC 265 VAC 3.15 A(T) 15 W a (F) denotes fast-acting fuse b (T) denotes time-delay fuse. c Power consumption varies based on configuration. 10/100Base-TX ports consume roughly 1 W less than fiber optic ports. d This is the same power supply for both AC and DC. 5.2 Failsafe Relay Specifications Voltage Current 30 VAC 0.3 A 30 VDC 1 A 80 VDC 0.3 A 5.3 Copper Ethernet Port Specifications The following details the specifications for copper Ethernet ports that can be ordered with the RUGGEDCOM RS8000T. Speeda 10/100Base-TX Connector RJ45 Duplexa FDX/HDX Cable Typeb > CAT-5 Wiring Standardc TIA/EIA T568A/B Maximum Distanced 100 m (328 ft) RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 21

Isolatione 1.5 kV a Auto-negotiating. b Shielded or unshielded. c Auto-crossover and auto-polarity. d Typical distance. Dependent on the number of connectors and splices. e RMS 1 minute. 5.4 Fiber Optic Ethernet Port Specifications The following details the specifications for fiber optic Ethernet ports that can be ordered with the RUGGEDCOM RS8000T. 5.5 Operating Environment The RUGGEDCOM RS8000T is rated to operate under the following environmental conditions. Ambient Operating Temperaturea -40 to 85°C (-40 to 185 °F) Ambient Storage Temperature -40 to 85°C (-40 to 185 °F) Ambient Relative Humidityb 5% to 95% Maximum Altitude 2000 m (6562 ft) a Ambient Temperature as measured from a 30 cm radius surrounding the center of the enclosure. b Non-condensing 5.6 Mechanical Specifications Weight 2.25 kg (5 lbs) Ingress Protection IP30 Enclosure 18 AWG Galvanized Steel 5.7 Dimension Drawings Note All dimensions are in millimeters, unless otherwise stated. 22 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 23

24 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

conformance with recognized standards and has received approval from recognized regulatory agencies. 6.1 Approvals This section details the standards to which the RUGGEDCOM RS8000T complies. 6.1.1 CSA This device is certified by the CSA Group to meet the requirements of the following standards: • CSA-C22.2 NO. 62368-1 Information Technology Equipment – Safety – Part 1: General Requirements (Bi- National standard, with UL 62368-1) • UL 62368-1 Information Technology Equipment – Safety – Part 1: General Requirements) 6.1.2 European Union (EU) This device is declared by Siemens AG to comply with essential requirements and other relevant provisions of the following EU directives: • EN 62368-1 Information Technology Equipment – Safety – Part 1: General Requirements • EN 61000-6-2 Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments • EN 50581 Technical Documentation for the Assessment of Electrical and Electronic Products with Respect to the Restriction of Hazardous Substances • EN 60825-1 Safety of Laser Products – Equipment Classification and Requirements RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 25

and methods of measurement The device is marked with CE and European Explosive Atmosphere symbols and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens AG. For contact information, refer to "Contacting Siemens (Page vii)". 6.1.3 FCC This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense. IMPORTANT Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. 6.1.4 ISO This device was designed and manufactured using a certified ISO (International Organization for Standardization) quality program that adheres to the following standard: • ISO 9001:2015 Quality management systems – Requirements 6.1.5 ACMA This device meets the requirements of the following Australian Communications and Media Authority (ACMA) standards under certificate ABN 98 004 347 880: • Radiocommunications (Compliance Labelling – Devices) Notice 2014 made under Section 182 of the Radiocommunications Act 1992 26 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

made under Section 182 of the Radiocommunications Act 1992 • Radiocommunications (Compliance Labelling – Electromagnetic Radiation) Notice 2003 made under Section 182 of the Radiocommunications Act 1992 • Telecommunications Labelling (Customer Equipment and Customer Cabling) Notice 2001 made under Section 407 of the Telecommunication Act 1997 The device is marked with an RCM symbol to indicate compliance when sold in the Australian region. A copy of the Declaration of Conformity is available via Siemens Industry Online Support at https://support.industry.siemens.com/cs/ww/en/view/89855782. 6.1.6 RoHS This device is declared by Siemens AG to meet the requirements of the following RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: • China RoHS 2 Administrative Measure on the Control of Pollution Caused by Electronic Information Products A copy of the Material Declaration is available online at https:// support.industry.siemens.com/cs/ww/en/view/109738831. 6.2 EMC and Environmental Type Tests The RUGGEDCOM RS8000T has passed the following EMC and environmental tests. IEC 61850-3 Type Tests Test Description Test Levels Severity Levels Enclosure Contact ±8 kV 4 IEC 61000-4-2 ESD Enclosure Air ±15 kV 4 IEC 61000-4-3 Radiated RFI Enclosure ports 20 V/m x Signal ports ±4 kV @ 2.5 kHz x IEC 61000-4-4 Burst (Fast Transient) DC Power ports ±4 kV 4 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 27

Test Description Test Levels Severity Levels AC Power ports ±4 kV 4 Earth ground ports ±4 kV 4 Signal ports ±4 kV line-to-earth, ±2 kV line-to-line 4 DC Power ports ±2 kV line-to-earth, ±1 kV line-to-line 3 IEC 61000-4-5 Surge AC Power ports ±4 kV line-to-earth, ±2 kV line-to-line 4 Signal ports 10 V 3 DC Power ports 10 V 3 AC Power ports 10 V 3 IEC 61000-4-6 Induced (Conducted) RFI Earth ground ports 10 V 3 IEC 61000-4-8 Magnetic Field Enclosure ports 40 A/m continuous, 1000 A/m for 1 s DC Power ports 30% for 0.1 s, 60% for 0.1 s, 100% for 0.05 s IEC 61000-4-29 30% for 1 period, 60% for 50 periods IEC 61000-4-11 Voltage Dips and Interrupts AC Power ports 100% for 5 periods, 100% for 50 periods Signal ports 2.5 kV common, 1 kV differential mode @ 1 MHz 3 DC Power ports 2.5 kV common, 1 kV differential mode @ 1 MHz 3 IEC 61000-4-12 Damped Oscillatory AC Power ports 2.5 kV common, 1 kV differential mode @ 1 MHz 3 Signal ports 30 V Continuous, 300 V for 1 s 4 IEC 61000-4-16 Mains Frequency Voltage DC Power ports 30 V Continuous, 300 V for 1 s 4 IEC 61000-4-17 Ripple on DC Power Supply DC Power ports 10% 3 Signal ports 2 kVAC  (Fail- Safe Relay output) DC Power ports 1.5 kVDC Dielectric Strength AC Power ports 2 kVDC Signal ports 5 kV  (Fail-Safe Relay Output) IEC 60255-5 HV Impulse DC Power ports 5 kV 28 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

Test Description Test Levels Severity Levels AC Power ports 5 kV IEEE 1613 (C37.90.x) EMC Immunity Type Tests Note The RUGGEDCOM RS8000T meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for copper ports. IEEE Test IEEE 1613 Clause Description Test Levels Enclosure Contact ±8 kV C37.90.3 9 ESD Enclosure Air ±15 kV C37.90.2 8 Radiated RFI Enclosure ports 35 V/m Signal ports ±4 kV @ 2.5 kHz DC Power ports ±4 kV AC Power ports ±4 kV Fast Transient Earth ground ports ±4 kV Signal ports 2.5 kV common mode @ 1MHz DC Power ports 2.5 kV common and differential mode @ 1MHz C37.90.1 7 Oscillatory AC Power ports 2.5 kV common and differential mode @ 1MHz Signal ports 5 kV (Failsafe Relay) DC Power ports 5 kV HV Impulse AC Power ports 5 kV Signal ports 2 kVAC (Failsafe Relay) DC Power ports 1.5 kVDC C37.90 6 Dielectric Strength AC Power ports 2 kVAC Environmental Type Tests Test Description Test Levels Severity Levels IEC 60068-2-1 Cold Temperature Test Ad -40 °C (-40 °F), 16 Hours IEC 60068-2-2 Dry Heat Test Bd 85 °C (185 °F), 16 Hours IEC 60068-2-30 Humidity (Damp Heat, Cyclic) Test Db 95% (non- condensing), 55 °C (131 °F), 6 cycles IEC 60255-21-1 Vibration 2 g @ 10-150 Hz Class 2 IEC 60255-21-2 Shock 30 g @ 11 ms Class 2 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05 29

30 RUGGEDCOM RS8000T Installation Manual, 01/2021, C79000-G8976-1023-05

https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens AG Digital Industry Process Automation Postfach 48 48 90026 NÜRNBERG GERMANY