Point Mobile PM85 Manual 

and battery cover. Unauthorized personnel are strictly prohibited from disassembling the phone. Make sure to use only the power adapter (5V 2A Output AC/DC) that came with PM85. In case your phone does not work as expected, you are strongly recommended to restart it by pressing and holding the power button for at least 12 seconds until the startup screen appears. If your phone has encountered a serious error and cannot be recovered, you should reset your phone to factory settings by using the menu, either “Backup & Reset”, or “Factory Reset”. For more details, please refer to “Factory data reset” section on page 32. Note: Please be cautious while performing the factory data reset. Because this will erase personalized settings and data saved in your phone, such as SMS, Contacts, Music, etc. Body-worn Operation This device was tested for typical bodyworn operations with the Front & back of the device kept 0.39 inches (1cm) between the user’s body and the Front & back of the device. To comply with FCC RF exposure requirements, a minimum separation distance of 0.39 inches (1cm) must be maintained between the user’s body and the Front & back of the device. Any beltclips, holsters, and similar accessories containing metallic components may not be used. Body-worn accessories that cannot maintain 0.39 inches (1cm) separation distance between the user’s body and the Front & back of the device, and have not been tested for typical body- worn operations may not comply with FCC RF exposure limits and should be avoided.. PROTECT YOUR HEARING To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your device near your ear while the loudspeaker is in use. www.sar-tick.com

1 Getting Started ........................................................ 3 1.1 Major Parts .......................................................... 3 1.2 Accessary ............................................................ 5 1.3 Setup PM85 ......................................................... 6 1.4 Charge PM85 ...................................................... 10 1.5 Turn On/Off PM85................................................ 11 2 Learning the basics ................................................ 12 2.1 Use a keypad ...................................................... 12 2.2 Using a keypad ......................................................... 13 2.3 Use a touch screen .............................................. 13 2.4 Home Screen, Apps and Widget ............................. 15 2.5 Status & Notifications Icons .................................. 18 2.6 Make a call ......................................................... 20 2.7 Add to a contact .................................................. 21 2.8 Send a message ........................................................ 22 3 OS Update .......................................................... 26 3.1 OS Image update from a Storage ................................ 26 3.2 OS Image update from the FOTA ............................... 28 4 Factory data reset................................................... 30 4.1 Factory data reset from Settings ............................ 30 4.2 Factory data Reset .............................................. 32

1.1 Major Parts 16 TPU 2 1 3 Ear jack 5 14 Side deco 12 13 15 USB 8 4 6 7 Pogo pin

17 TPU Texture MT11010 (PC) 18 9 11 10 19 20 1 Front cover 11 Battery locker 2 Front deco receiver 12 Power button 3 Front camera 13 Volume button 4 Front deco speaker 14 Scan button 5 Touch screen 15 Sos button 6 Keypad 16 Scan window 7 Keypad pad 17 Camera window 8 Function deco 18 Flash window 9 Rear housing 19 Cap screw 10 Battery cover 20 Hand strap

Micro USB C Type Cable AC plug (US/EU/UK) Battery (2900mAh) Battery (5800mAh) Hand Strap

1.3.1 Remove the Battery Cover 1. Push down the Battery locker. 2. Lift up the Battery Cover. 3. Remove the Battery Cover.

Insert “Battery” from top area first and then put in top area. 1.3.3 Close the Battery Cover Insert “Battery Cover” from the bottom area first and then put in top area. Press battery cover with both hand firmly.

You must insert your SIM card to make phone calls. Please power off your phone before inserting or removing the SIM card. 1. Remove the Battery Cover and the Battery. 2. Lift up the SIM rubber. 3. Insert the SIM-SAM card into the slot. (Gold plate should face down). Make sure that it is correctly inserted. 4. To remove the card, repeat step1 and step2, then remove the card out of the slot. Note: Your device only supports SIM cards. Do not attempt to insert other SIM types such as “Micro” and “Nano” SIM card, this may cause damage to your device. If you have to use different SIM card types, please use “SIM adaptor”. SAM

1. Remove the Battery Cover and the Battery. 2. Lift up the SIM rubber. 3. Insert the microSD card into the slot (Gold plate should face down). 4. To remove the microSD card, repeat step1 and step2, then remove the card out of the slot. Note: To avoid data loss and SD card damage, please power off your phone before inserting or removing the SD card.

1. Connect the AC/DC adaptor to your device and wall socket respectively. 2. LED indicator will display charging status. Steady Red Battery is charging or Battery level is low Blinking Red Battery level is critical low Steady Green Battery is fully charged PM85 Battery Specification Standard Battery 2,900mAh 3.85V Backup Battery 5,800mAh 3.85V Charging time About 5 hours Note: Always use an original charger and cable from the Point Mobile. Other chargers and cables may damage PM85. In addition, make sure connector, charger, cables are not wet.

Turn On 1. Press and hold down the “Power Key” for a few seconds. 2. When PM85 enter to the boot mode, it will display “SMART BEYOND RUGGED” logo with short vibration. 3. Release the “Power Key” and wait until PM85 finish booting. Note: If you cannot turn on your PM85, try below steps: - To turn on PM85, battery needs to be charged certain level. Please charge first. - Press and hold the “Power key” for 12 seconds to force reboot. Turn Off 1. Press and hold the “Power Key” until you see the power menu. 2. Among the menu, tap “Power off”.

2.1 Use a keypad Power key Press - Lock the screen / Light up the screen. Press and hold - Display the power menu “Power off / Restart”. Press and hold for over 12seconds - Forced to reboot. Press and hold the “Power” key and “Volume Down” key together - Screen capture. Volume keys In general - Adjusts the ringtone volume or “Mute” the ringtone of an incoming call. In call mode - Adjusts the earpiece or headset volume. In Music / Video / Streaming - Adjusts the media volume. In camera preview - Take the photo by pressing Volume Up or Down key.

Front panel Recent Apps key - Press to see recently used apps. Home key - From any apps or screens, press to return to the Home screen. Back key - Press to go back to the previous screen, or to close a dialog box, options menu, notification panel, etc. 2.3 Use a touch screen Touch One-finger press Double touch One-finger press, lift, one-finger press, lift for “Zoom in” Long press One-finger press, wait, lift for “Select an item”

One-finger press, move, lift for “Scroll” or “Tilt” Long-press drag One-finger press, wait, move, lift for “Pick up and move” or “select multiple items” Scroll Vertical or horizontal swipe in a single direction Pinch Open & Close Two-finger press, move outwards and inwords, lift for “Zoom in and out” Rotate When PM85 is turning sideways, screen orientation is changing

Status Bar - Status / Notification - Drag down to open the “Quick Setting Panel” Search Bar - Touch 1 to search by text - Touch 2 to search by voice Touch an icon to run an app, open folder, etc. Favorite tray apps - Touch to run an app - Touch and hold to reorganize App Drawer Touch to enter “Apps and Widget” Remove the app icon from home screen - Long press the app icon and then drag it to the “Remove” area and then release

- Long press the app icon to other app icon. This will create the “App Folder” - To set the folder name, touch the “Unnamed Folder” and rename it Notification panel When there are notifications from the Android (system) or the App, you can check details by drag down the “Status Bar”.

You can access “Quick setting panel” by drag down the “Notification panel”. You can enable / disable functions or change modes easily. By touching the “App drawer” icon, all installed apps are listed in the tab, alphabetically. - Tap app icon to run. - Long press, specific app icon to place to the “Home Screen”.

- On the home screen, touch and hold an empty area of the screen. - Touch "WIDGETS". - Long press, specific widget to place to the “Home Screen”. 2.5 Status & Notifications Icons Status icons GPRS connected GPRS in use EDGE connected EDGE in use 3G connected 3G in use 4G connected 4G in use Signal strength No signal Roaming Airplane mode No SIM card installed

Connected to a Bluetooth device Battery is full Battery is partially drained Battery is low Battery is very low Battery is charging GPS is on Alarm is set Speaker phone is on Headset connected Vibrate mode/ Mute Phone mic is mute Notification icons Missed call New SMS or MMS message New Email Connected to VPN network Upcoming event Screenshot captured Preparing SD card SD card removed, unexpectedly OTG device connected File uploaded File downloaded There are more notification Other input method available

Touch icon in the Favorite tray apps. Slide to access the “Favorites”, “Recents” and “Contacts”. - Touch to use a dialer - To make a call from recent call list or missed call, select “Recents” tab - To make a call from your contact list, select “Contracts” Suggested phone number(s) Phone number can be saved to “CONTACTS” Touch and hold the dial pad #1, to access voicemail.

1. If your device is unlocked, in the call notification window, tap ANSWER or DECLINE. 2. If your device is locked . • Swipe up to answer a call. • Swipe down to reject a call. • Touch to reject the call and send a preset message to the caller. 3. When Settings > Accessibility > Power button ends call is turned on, press the Power key to dismiss the call. Tip: To mute the ringtone volume of an incoming call, press the “Volume down” key. 2.7 Add to a contact Touch “App Drawer” icon and then icon . CREATE A NEW CONTACT You can manually create the new contact.

Touch to add a new contact SIGN IN TO AN ACCOUNT You can sync with your contacts in the Google account. IMPORT CONTACTS You can import contact in the storage (.vcf file) or SIM card. 2.8 Send a message Touch icon in the Favorite tray apps. Touch icon to edit a new message.

Touch to type a name, phone number or email Suggest contact display here. Touch “Contacts” to compose a message Your message display here Touch to send the composed message You can attach photo, saved picture, voice or location Note: You may allow granting “Message App” access specific app or service.

3.1 OS Image update from a Storage To update OS image, copy or place OS image file into the root folder of “Internal Storage” or “External Storage”. Touch “App Drawer” - “Settings” - "System" and then “About phone” Touch “System Updates”

Touch “Update” button By touching the “CONTINUE” button, your PM85 start to update the OS image. During this time, you cannot use your PM85. Please save the data before start, the OS update process.

Tap icon for the advanced option Touch “FOTA Client” PM85 will compare the OS image between FOTA server and current OS image. If there is newer OS image in the FOTA server, FOTA server will suggest downloading.

the image in the FOTA server You can cancel OS image download process Note: Default OS image download setting of FOTA Client is “Download over Wi-Fi only” Please connect to the nearby Wi-Fi network for FOTA service.

4.1 Factory data reset from Settings When your PM85 system is unstable and abnormal behavior occur but could not recover by rebooting, you may need to “Factory data reset” your PM85. Touch “App Drawer” - “Settings” and then “Reset options” Touch “Erase all data (factory reset)”

restored to “Factory default” and this process cannot “Undo”. Touch to start “RESET PHONE” process Touch to confirm erase of “ERASE EVERYTHING”

Force Factory data reset your PM85 You can perform “force” factory data reset your PM85. When your PM85 turned off, press “Power” + “Volume up” + “Home” button all together. After short vibration from your PM85, you may release the buttons. PM85 enter to the “Android Recovery” mode. In this mode, “Volume up” is “Move Up” in the menu tree and “Volume down” is “Move Down” in the menu tree. “Power Button” is “Select”. Press Power +

Select “Yes” to perform the “Factory data reset”. After that, your PM85 start wiping the data. After data wiping, please select “Reboot system now” to finish the “Force Factory data reset” process. DO NOT select

following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help Caution: Any changes or modifications to this device not expressly approved by the party responsible for compliance could void your authority to operate the equipment. IC warning This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si lebrouillage est susceptible d’en compromettre le fonctionnement.

Cet appareil est restreint a l'utilisation a l'interieur seulement dans la bande 5.15 ~ 5.35GHz. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC/IC. Cet equipement est conforme aux limites d'exposition aux radiations FCC / IC definies pour un environnement non controle. Cet emetteur ne doit pas etre colocalise ou fonctionner en conjonction avec une autre antenne ou un autre emetteur, a moins d'etre autorise a le faire par le FCC / IC. E-label (FCC ID & IC, etc) Users can able to access the FCC/IC in 3steps in device’s manu. The actual steps are : - Settings -> About phone -> Certificates WCDMA/LTE feature is optional Some product options only include WLAN feature. WLAN PHONE FCC ID V2X-PM85W V2X-PM85G IC ID 10664A-PM85W 10664A-PM85G