Playcraft 1932 Installation Instructions

www.playcraftsystems.com For Customer Service Call 800.333.8519 (U.S.A.) or 541.955.9199 (International) HAND SPIN CYCLER INSTALLATION INSTRUCTIONS Rev B 4/7/2020 1932 Page 1 of 3 See Installation Manual Sections 09 Collars and 11 Clamps (A) Use liquid thread lock (such as Loctite ®) with all threaded hardware. Important: Liquid thread lock (prior to curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a lubricant during assembly. (B) Refer to Installation Manual for 09 Collars and 11 Socket Clamps assembly instructions. NOTE: R5 Hand Spin Cycler shown. Other configurations will vary slightly, but does not affect assembly. FIGURE 1 Hand Spin Cycler R5

800.333.8519 (U.S.A.) or 541.955.9199 (International) HAND SPIN CYCLER INSTALLATION INSTRUCTIONS Rev B 4/7/2020 1932 Page 2 of 3 3/8" x 2" Barrel Nut KNOB KNOB SPACER MAIN PANEL SPINNER FACE 3/8" x 7/8" O.D. Washer 3/8" x 2-1/2" Button Head Bolt SPINNER FACE FIGURE 1 3/8" x 1" O.D. Washer 12" 305mm SIDE ELEVATION SOCKET CLAMP TOP 6mm Washer 1/4" x 1" Socket Head Screw MOUNTING LUG SOCKET CLAMP BOTTOM 3/8" x1/2" Socket Set Screw FIGURE 2 Step 1 (Factory Assembled) Assemble Spin Cycler components as shown in Figure 1. (See Note A) Step 3 Attach Mounting Lugs to collars as shown in Figure 2. (See Notes A and B)

800.333.8519 (U.S.A.) or 541.955.9199 (International) HAND SPIN CYCLER INSTALLATION INSTRUCTIONS Rev B 4/7/2020 1932 Page 3 of 3 MAIN PANEL 3/8" x 1" O.D. Washer 3/8" x 1-1/2" Button Head Bolt MOUNTING LUG FIGURE 3 Step 4 Attach Main Panel to mounting lugs as shown in Figure 3. (See Note A) Step 5 Fully tighten all fasteners according to the "TIGHTENING TORQUE FOR HARDWARE" section of the Installation Manual. HAND SPIN CYCLER MAIN PANEL, SPINNER FACE, CENTER SPACER, KNOB SPACER AND KNOB: Shall be made from high density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked- on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. Parts List Assembled Parts List R5 Hand Spin Cycler Part # DESCRIPTION QTY GF-7007 Mounting Lug R5 2 HS-1001-R5 Socket Clamp Set R5 2 9103072-TR Bolt Button Head 3/8" x 1-1/2" 2 9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 2 R35 Hand Spin Cycler Part # DESCRIPTION QTY. GG-8113 Mounting Lug R3.5 2 HS-1001-R35 Socket Clamp Set R3.5 2 9103072-TR Bolt Button Head 3/8" x 1-1/2" 2 9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 2 Part # DESCRIPTION QTY EE-0102-CS Hand Spin Cycler - Center Spacer 1 EE-0102-K Hand Spin Cycler - Knob 2 EE-0102-KS Hand Spin Cycler - Knob Spacer 2 EE-0102-MP Hand Spin Cycler - Main Panel 1 EE-0102-SF Hand Spin Cycler - Spinner Face 2 9103112-TR Bolt Button Head 3/8" x 2-1/2" 2 9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 2 9333042 Washer Flat 3/8" x 7/8" O.D. 2 9443092-TR Nut Barrel 3/8" x 2" BH 2 Periodically tighten all screws, bolts and nuts. A periodic inspection of all parts is necessary. If a part is broken or worn, replace immediately. For general maintenance please refer to our Playground Maintenance Manual. Maintenance