Videotec MAXIMUS MVXHD Instruction Manual

ENGLISH MAXIMUS MVXHD High-spec ex-proof HD camera in a compact design Manual B

3 MNGCMVXHDCAM_1813_EN Contents ENGLISH 1 1 About this manual ....................................................................................................................5 1.1 Typographical conventions ................................................................................................................................................ 5 2 Notes on copyright and information on trademarks .............................................................5 3 Identification .............................................................................................................................5 3.1 Product marking ..................................................................................................................................................................... 5 4 Installation ................................................................................................................................6 4.1 Range of use ............................................................................................................................................................................. 6 4.2 Connection of the power supply line .............................................................................................................................. 6 4.3 Connection of the Ethernet cable .................................................................................................................................... 7 4.4 Signal cable connection ....................................................................................................................................................... 7 4.4.1 Alarm and relay connections ...............................................................................................................................................................7 4.4.1.1 Connecting an alarm with dry contact ....................................................................................................................................................................7 4.4.1.2 Relays connection ...........................................................................................................................................................................................................8 4.5 Washing system connection .............................................................................................................................................. 8 5 Switching on .............................................................................................................................8 5.1 Before powering the product in an explosive atmosphere .................................................................................... 8 5.2 First start-up ............................................................................................................................................................................. 8 6 Configuration ............................................................................................................................9 6.1 Default IP address................................................................................................................................................................... 9 6.2 Web interface ........................................................................................................................................................................... 9 6.2.1 First access to the web pages ..............................................................................................................................................................9 6.3 Inserting an SD Card .............................................................................................................................................................. 9 7 Maintenance ...........................................................................................................................10 7.1 Factory Default ......................................................................................................................................................................10 8 Information on disposal and recycling .................................................................................10 9 Troubleshooting .....................................................................................................................11 10 Technical data .......................................................................................................................11 10.1 Cameras .................................................................................................................................................................................11

5 MNGCMVXHDCAM_1813_EN 1 About this manual Read all the documentation supplied carefully before installing and using this unit. Keep the manual in a convenient place for future reference. This document has been compiled and published using product descriptions and specifications available at the time of publication. The contents of this document and the specifications of the products discussed herein are subject to change without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the information contained in this document; or (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein. 1.1 Typographical conventions DANGER! High level hazard. Risk of electric shock. Disconnect the power supply before proceeding with any operation, unless indicated otherwise. CAUTION! Medium level hazard. This operation is very important for the system to function properly. Please read the procedure described very carefully and carry it out as instructed. INFO Description of system specifications. We recommend reading this part carefully in order to understand the subsequent stages. 2 Notes on copyright and information on trademarks The mentioned names of products or companies are trademarks or registered trademarks. AVIGILON, the AVIGILON logo, and AVIGILON CONTROL CENTER are trademarks of Avigilon Corporation. Other names or logos mentioned herein may be the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of ownership of the related trademark. ONVIF® is a trademark of Onvif, Inc. 3 Identification 3.1 Product marking See the label attached to the product.

6 MNGCMVXHDCAM_1813_EN 4 Installation CAUTION! Device installation and maintaining must be performed by specialist technical staff only. The external multipolar cable shield (armature) must be earthed. All disconnected wires must be electrically isolated. The product comes with a multipolar cable or a cable tail for coupling purposes. When installing the device with the multipolar cable, keep at least 250mm free space from the bottom of the housing to allow for the minimum curvature radius of the multipolar cable. 4.1 Range of use For indoors and outdoors installation. Installation temperature: from -40°C (-40°F) up to +60°C (140°F). Operating temperature: • -40 °C to 55 °C (-40 °F to 131 °F), in enclosed space • -40 °C to 60 °C (-40 °F to 140 °F), with ambient convection Relative humidity: from 10% up to 95% (no condensation). 4.2 Connection of the power supply line Electrical connections must be performed with the power supply disconnected and the circuit-breaker open. When commencing installation make sure that the specifications for the power supply for the installation correspond with those required by the device. Check that the power supply is adequately dimensioned. The device can be provided with different power supply voltages. The power supply voltage is indicated on the product identification label. (3.1 Product marking, page 5). The multicore cable has the power and earth cables inside. Perform the connections following the instructions reported in the table . CONNECTION OF THE POWER SUPPLY LINE Power supply 24Vac/ 24Vdc/ 12Vdc Colour Terminals Black 1 (+) L (Phase) Black 2 (-) N (Neutral) Yellow/Green Tab. 1

7 MNGCMVXHDCAM_1813_EN 4.3 Connection of the Ethernet cable The Ethernet cable shield must always be earthed via the connector. Always use a shielded RJ45 connector. Use of Ethernet cables with the following characteristics is highly recommended: • STP (shielded) • Category 5E (or higher) The product can be directly connected to an Ethernet switch. Carry out the connections as described in the table (according to the standard specifications: TIA/EIA- 568-B). CONNECTION OF THE ETHERNET CABLE Pin number Cable color 1 Orange-White 2 Orange 3 Green-White 4 Blue 5 Blue-White 6 Green 7 Brown-White 8 Brown Tab. 2 The example below shows a typical installation. Switch Personal Computer Fig. 1 4.4 Signal cable connection CAUTION! TNV-1 installation type. The installation is type TNV-1, do not connect it to SELV circuits. SIGNAL CABLE CONNECTION Colour Function White RS-485 A (+) Yellow RS-485 B (-) Pink Relay 1, Terminal A Violet (blue, cable tail version) Relay 1, Terminal B Red (brown, cable tail version) Alarm/Digital input Green GND/Common alarm Grey Reset Tab. 3 4.4.1 Alarm and relay connections The external relay and alarm cable shield must be earthed. The unit is equipped with the alarms and relays indicated in the table (Tab. 3, page 7). 4.4.1.1 Connecting an alarm with dry contact In case of free contact alarm make the connection as shown in the figure. AL1 COM dry contact Fig. 2 AL1: Alarm 1. COM: Common alarms. The dry contact alarm can be NO (normally open) or NC (normally closed).

8 MNGCMVXHDCAM_1813_EN 4.4.1.2 Relays connection The relays are usable with the specifications described below. Working voltage: up to 15Vac or 30Vdc. Current: 1A max. Use suitable cable sections with the following characteristics: from 0.25mm² (23AWG) up to 1.5mm² (15AWG). Due to the absence of polarity, both terminals of the same relay can be connected either to alternating or direct current voltages. 4.5 Washing system connection For further details on configuration and use, refer to the relative manual. 5 Switching on The automatic pre-heating procedure (De- Ice) activates for 2 hours if on device switch on an ambient temperature is detected under -10 °C (+14°F). The procedure is necessary to guarantee correct operation of the devices even at low temperatures. The full functionality of the product is guaranteed from the following ambient temperature: -40°C. Do not turn on the unit when the ambient temperature is lower than indicated: -40°C. The unit is switched on by connecting the power supply. To switch off the unit disconnect the power. 5.1 Before powering the product in an explosive atmosphere Make sure that all parts are fastened down firmly and safely. Make sure that the unit and other components of the installation are closed so that it is impossible to come into contact with live parts. Make sure that the device has been connected to an earth link as described. Ensure the rear cover plate is correctly closed. Ensure the product is correctly closed. Ensure that the sealing of cable entry systems (if any) has been performed properly and the time of glue hardening has been observed. 5.2 First start-up Make sure that the unit and other components of the installation are closed so that it is impossible to come into contact with live parts. Make sure that all parts are fastened down firmly and safely.

9 MNGCMVXHDCAM_1813_EN 6 Configuration 6.1 Default IP address The unit is configured to obtain an IP address from a DHCP server. The IP address acquired via DHCP is visible in the DHCP server log file. If the DHCP server is not available, the unit automatically configures itself with a self-generated IP address in the 169.254.x.x/16 subnet. Configuring the IP address of the PC as belonging to the same subnet (example: IP address: 169.254.1.1, subnet mask: 255.255.0.0). Use an ONVIF compliant VMS or the Avigilon™ Camera Configuration Tool to find the IP address of the device. 6.2 Web interface Browsers supported (the latest version): Microsoft Edge, Google Chrome, Mozilla Firefox. 6.2.1 First access to the web pages The first operation in configuring the device consists in connecting to the web interface. To access the web interface of the product, simply use a browser to connect to http://ip_address. On first access, the Home page will be displayed. Additional information about setting up and using the device is available in the following guides: • Web Interface User Guide — Avigilon High Definition H4 and H5 IP Cameras • Avigilon Camera Configuration Tool User Guide • Designing a Site with Avigilon Video Analytics • Avigilon Control Center™ Client User Guide These guides are available on help.avigilon.com and on the Avigilon website: avigilon.com/support-and- downloads. 6.3 Inserting an SD Card For instruction about opening and closing the camera, please refer to Manual A. For onboard video storage capabilities, please insert an industrial grade microSD card into the slot as show (Fig. 3, page 9). Fig. 3

10 MNGCMVXHDCAM_1813_EN 7 Maintenance Read the product Manual A before performing any operation. Please provide the device serial number when requesting any replacement parts. 7.1 Factory Default It is possible to reset to the factory default settings. Follow the procedure below: • Power the unit. Wait for 3 minutes. • Connect the signal cable grey and green wires ( Tab. 3, page 7). • Wait for 3 minutes. • Switch off the unit. Disconnect the previously connected green and grey wires. • Power the unit. 8 Information on disposal and recycling The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE) mandates that these devices should not be disposed of in the normal flow of municipal solid waste, but they should be collected separately in order to optimize the recovery stream and recycling of the materials that they contain and to reduce the impact on human health and the environment due to the presence of potentially hazardous substances. The symbol of the crossed out bin is marked on all products to remember this. The waste may be delivered to appropriate collection centers, or may be delivered free of charge to the distributor where you purchased the equipment at the time of purchase of a new equivalent or without obligation to a new purchase for equipment with size smaller than 25cm (9.8in). For more information on proper disposal of these devices, you can contact the responsible public service.

11 MNGCMVXHDCAM_1813_EN 9 Troubleshooting Contact an authorized support centre if the problems listed below persist or you have any other issues that are not described here. Read the product Manual A before performing any operation. PROBLEM Video streaming is not visible. CAUSE Incorrect IP address settings. SOLUTION Check the device IP address and the configuration of the computer network card. CAUSE Automatic preheating procedure (De-Ice) in progress. SOLUTION Wait until the end of the pre- heating procedure. If the ambient temperature is too low the unit will remain blocked. PROBLEM The wash system is blocked and does not respond to commands. CAUSE The wash system is not enabled. SOLUTION Check the configuration of the settings. PROBLEM The wash system settings are incorrect. CAUSE Wrong settings in the configuration. SOLUTION Check the configuration of the settings. 10 Technical data 10.1 Cameras Resolution: Full HD 1080p (1920x1080pixel) Image Sensor: 1/2.8" Progressive Scan CMOS Focal length: from 4.3mm (wide) up to 129mm (tele) Zoom: 30x Max Aperture: F1.6 Horizontal Angle of View Based on Aspect Ratio:(16:9) 2.3°-66° Electronic Shutter Control: Automatic, Manual White balance: Automatic, Manual Wide Dynamic Range: 120dB Exposure Control: Automatic, Manual, Priority (Iris Priority, Shutter Priority), Brightness, Custom De-fog: On/Off Privacy Zones: Yes Day/Night Control: Automatic, Manual Flicker Control: 60Hz, 50Hz Backlight Compensation: On/Off

Via Friuli, 6 - I-36015 Schio (VI) - Italy Tel. +39 0445 697411 - Fax +39 0445 697414 Email: [email protected] France Videotec France SARL Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf 91140 Villebon sur Yvette - France Tel. +33 1 60491816 - Fax +33 1 69284736 Email: [email protected] Asia Pacific Videotec (HK) Ltd Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street Kwai Chung, New Territories - Hong Kong Tel. +852 2333 0601 - Fax +852 2311 0026 Email: [email protected] Americas Videotec Security, Inc. Gateway Industrial Park, 35 Gateway Drive, Suite 100 Plattsburgh, NY 12901 - U.S.A. Tel. +1 518 825 0020 - Fax +1 518 825 0022 Email: [email protected] www.videotec.com