Sena HelloDevice Pro PS110 Quick Start Manual

Quick Start Guide PS110 Set DIP Switch & Pin-outs Connection Configuration Set serial DIP switch according to your serial device requirements(RS-232/422/485) * Please note that the power of the Pro Series should be turned off before changing the serial communication type. User can choose one of the following processes 1. Configuration using the HelloDevice manager 2. Configuration using the Hyper terminal or Telnet 3. Configuration using the Web Connect to host PC. Then, slide Data/Console switch to the Console side. Set up the serial configuration parameters of the terminal emulation program as follows: DIP Switch Setting RS232 (console and serial ports) RS422 (serial ports only) RS485 (serial ports only) 1 DCD Tx+ Tx+ 2 Rx RX+ RX+ 3 Tx RTS+ - - - - 4 DTR CTS+ 5 GND GND GND 6 DSR TX- TX- 7 RTS RTS- 8 CTS RX- RX- DB-9 Pinouts 9 - CTS- ON RS-232 Mode ON RS-422/485 Full Mode ON RS-485 Half Mode Serial Device Connect serial device Insert CD www.sena.com Connect Ethernet cable Connect Power supply Data/console 9600 Baud rate/8 Data bits/None Parity/ 1 Stop bits/No Hardware flow control Copyright 1998-2005, Sena Technologies, Inc. All rights reserved. Visit us at www.sena.com HelloDevice Manager and User Manual are available for download from CD or Sena website at http://www.sena.com/support/downloads/. For more information, refer to the user manual.

Quick Start Guide PS410 www.sena.com Set DIP Switch & Pin-outs Connection Configuration Set serial DIP switch according to your serial device requirements(RS-232/422/485) * Please note that the power of the Pro Series should be turned off before changing the serial communication type. User can choose one of the following processes 1. Configuration using the HelloDevice manager 2. Configuration using the Hyper terminal or Telnet Connect the host PC and PS410's console port using a serial console cable. Set up the serial configuration parameters of the terminal emulation program as follows: DIP Switch Setting RS232 (console and serial ports) RS422 (serial ports only) RS485 (serial ports only) 1 DCD Tx+ Tx+ 2 Rx RX+ RX+ 3 Tx RTS+ - - - - 4 DTR CTS+ 5 GND GND GND 6 DSR TX- TX- 7 RTS RTS- 8 CTS RX- RX- DB-9 Pinouts 9 - CTS- ON RS-232 Mode ON RS-422/485 Full Mode ON RS-485 Half Mode Serial Device Connect serial device Connect Ethernet cable Connect Power supply 3. Configuration using the Web Insert CD www.sena.com PC 9600 Baud rate/8 Data bits/None Parity/ 1 Stop bits/No Hardware flow control Copyright 1998-2005, Sena Technologies, Inc. All rights reserved. Visit us at www.sena.com HelloDevice Manager and User Manual are available for download from CD or Sena website at http://www.sena.com/support/downloads/. For more information, refer to the user manual.

Quick Start Guide PS810 Pin-outs Connection Configuration User can choose one of the following processes 1. Configuration using the HelloDevice manager 2. Configuration using the Hyper terminal or Telnet Connect the host PC and PS810's console port using a serial console cable. Set up the serial configuration parameters of the terminal emulation program as follows: 9600 Baud rate/8 Data bits/None Parity/ 1 Stop bits/No Hardware flow control Serial Device Connect serial device 3. Configuration using the Web Insert CD www.sena.com PC Connect Ethernet cable * User can change the serial communication type using software such as hyper terminal, telnet or web management interface. RS232 (console and serial ports) RS422 (serial ports only) RS485 (serial ports only) 1 DCD Tx+ Tx+ 2 Rx RX+ RX+ 3 Tx RTS+ - 4 DTR CTS+ - 5 GND GND GND 6 DSR TX- TX- 7 RTS RTS- - 8 CTS RX RX- DB-9 Pinouts 9 - CTS- - Connect Power cord Copyright 1998-2005, Sena Technologies, Inc. All rights reserved. Visit us at www.sena.com HelloDevice Manager and User Manual are available for download from CD or Sena website at http://www.sena.com/support/downloads/ For more information, refer to the user manual.