Dual XDMA6700 Installation & Owner's Manual

XDMA6700

Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove trim ring from unit, • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. Consult a qualified technician if you are unsure. • Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place. • Mount the iplug™ adapter to any smooth clean surface using the supplied double-sided tape or #2 x 3/8” Phillips head screws. XDMA6700 INSTALLATION Preparation

make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDMA6700 uses one 10 amp ATM fuse located beside the wiring connector. XDMA6700 INSTALLATION Wiring Diagram BLACK Front Preamp Output WHITE 10-pin Female Mini-DIN IPC2M Connection (sold separately) BLACK 8-pin Female Mini-DIN BTM60 Connection (sold separately) Yellow Auxiliary Input Antenna Connector

CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track search - even while a song is currently playing! Function keys 7, 8, 9 and 0 apply to Bluetooth, iPod and MP3/WMA operation only. XDMA6700 OPERATION Control Locations - Receiver Release Band/Play/Pause/Key * Volume/Audio/Setup Mode/Search Preset 4/Menu Preset 1/Repeat Preset 5/Folder Down Preset 2/Random Preset 3/Intro Eject Preset 6/Folder Up 1 2 3 4 5 6 7 8 9 10 11 EQ/Key 9 Mute/End Call Display/Key 0 Tuner Scan/Key 8 Call/Redial Return/Key 7 Auto Store/Preset Scan/Enter/Key # Power Tune/Track Down Tune/Track Up 12 13 14 15 16 17 18 19 20 21 19 21 18 17 16 15 14 13 12 1 2 3 5 6 7 8 9 10 11 4 20

General Operation XDMA6700 OPERATION 5 Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Remove trim ring, and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Press POWER or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press POWER to turn the unit off. Press MODE to select between AM/FM, CD player, auxiliary input, iPod (optional), and Bluetooth (optional). Modes of operation are indicated in the display. Note: CD, iPod, and Bluetooth modes will not appear unless a CD is inserted, IPC2M (iPod cable - sold separately) and iPod are attached, or BTM60 (Bluetooth module - sold separately) is attached. Adjust volume using rotary encoder (00-46). Press and hold POWER for 3 seconds to program currently selected volume level. "P-VOL" and the current volume level will momentarily appear in the display. Press MUTE to silence the audio. “MUTE” will flash in the display. Press MUTE again to cancel. Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK and OFF (default) equalization curves. Any adjustment to the Bass or Treble settings automatically cancels the current EQ curve (if one is selected).

information, such as radio frequency, CD track/elapsed time, or MP3/WMA/iPod song information. With the unit on, press and hold DISP until the clock begins to flash, then release. Press TUNE nn to adjust the hours and TUNE ll to adjust the minutes. Press DISP momentarily to save the selected time. The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). The desired requency spacing can be selected through the setup menu. Press to RESET the unit upon initial installation or if abnormal operation occurs. The reset button is located behind the faceplate. Press and hold the rotary encoder for more than 3 seconds to access the setup menu. Press the rotary encoder momentarily to select between the menu functions and rotate the rotary encoder left/right to adjust or activate the desired function. Display Set the Clock 12/24-hour Clock Reset Setup Menu XDMA6700 OPERATION General Operation

Menu Function Options Action Loudness Curve LOUD OFF Disables the loudness function. LOUD ON Enables the loudness function. Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes. Tuner Frequency Spacing FREQ USA Programs the unit to USA tuner spacing. (200kHz for FM and 10kHz for AM) FREQ EUR Programs the unit to European tuner spacing. (50kHz for FM and 9kHz for AM) Clock Display CLK OFF Programs the unit to not display the clock when the power is off. CLK ON Programs the unit to display the clock when the power is off. Auxiliary Mode AUX ON Enables access to auxiliary mode. AUX OFF Disables access to auxiliary mode. Beep Confirmation BEEP OFF Disables the confirmation beep. BEEP ON Enables the confirmation beep. Local/Distance Tuning LOC OFF Activates distance tuning. LOC ON Activates local tuning for strong station reception only. Power on Message MSG OFF Disables power on message. MSG ON Enables power on message to be displayed. Demonstration Mode DEMO ON Enables the "BT READY AND IPOD READY" message. DEMO OFF Disables the demonstration mode.

Volume (default), Bass, Treble, Balance and Fader. Press rotary encoder until BAS appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press rotary encoder until TRE appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum). Press rotary encoder until BAL appears then rotate encoder left/right to adjust (BAL L 12-BAL 00-BAL R 12). BAL 00 represents equal balance. Press rotary encoder until FAD appears then rotate encoder left/right to adjust (FAD F 12-FAD 00-FAD R 12). FAD 00 represents equal fader. Individual bass and treble settings are retained in memory for AM, FM, CD, AUX, iPod and Bluetooth modes. This allows you to save the bass and treble settings separately for each mode. Note: Any adjustment to the bass or treble settings automatically cancels the current EQ curve (if one is selected). Audio Bass Treble Balance Fader Source Audio Memory XDMA6700 OPERATION General Operation BASS VOLUME TREBLE BALANCE FADER

Station Presets Automatically Store Stations Preset Scan Press TUNE nn or TUNE ll momentarily to seek the next strong station. Press TUNE nn or TUNE ll for more than two seconds, then release. "MANUAL" will momentarily appear in the display. Press TUNE nn or TUNE ll momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for five seconds, the unit will return to seek tuning mode (default). "AUTO" will momentarily appear in the display. Press SCN to preview strong stations on the current band, pausing for five seconds at each. Press SCN again to cancel. Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to 18 FM stations and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear in the display. The station can be recalled at any time by pressing the corresponding preset button. Note: Function keys 7, 8, 9 and 0 apply to Bluetooth, iPod and MP3/WMA operation only. Press AS/PS for more than two seconds to automatically store the six strongest stations in the current band. Automatic local tuning is activated during the initial band scan. Press AS/PS for less than two seconds to scan presets 1-6 on the current band, pausing for five seconds at each. Press AS/PS again to cancel. XDMA6700 OPERATION AM/FM Tuner Operation

Pause Scan Repeat Random CD-R/CD-RW Compatibility With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation (AM, FM, auxiliary input, iPod or Bluetooth). If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD. Press TRACK ll to skip to the beginning of the next track. Press TRACK nn to return to the beginning of the current track. Pressing TRACK nn again skips to the beginning of the previous track. Press and hold TRACK ll or TRACK nn to fast forward or reverse a track. Press l/ II to temporarily stop CD playback. Press l/ II again to resume playback. Press INT to play the first 10 seconds of each track. Press INT again to cancel. Press RPT to continuously repeat selected track. Press RPT again to cancel. Press RDM to play all tracks in random order. Press RDM again to cancel. Random mode is retained in memory when selecting between AM/FM tuner, iPod, CD player, auxiliary input and Bluetooth modes and when the unit is turned on/off. Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. The following CDs may also be incompatible with this unit: - CDs exposed to extreme temperatures or direct sunlight for extended periods of time, - CDs recorded in which a recording session failed or a re- recording was attempted - Encrypted or copy-protected CDs which do not conform to the audio CD-DA red book recording standard. XDMA6700 OPERATION CD Player Operation

Playing an MP3/WMA Disc Displaying Information Title Icon Artist Icon Album Icon Folder Icon Character Support When an MP3/WMA encoded disc is first inserted, “READING” will appear in the display. Depending on the number of files and folders, this may take several seconds. Press DISP to select between track number/elapsed time (default), clock, track name, directory name, title, artist and album. “NO ID3 TAG” will be displayed if the MP3 file contains no ID3 tag information. “UNKNOWN” will be displayed if the WMA file contains no WMA tag information. “ROOT” will be displayed if the directory name of a root folder is not labeled. This icon will illuminate when the song title is displayed. This icon will illuminate when the artist name is displayed. This icon will illuminate when the album name is displayed. This icon will illuminate when the folder name is displayed. Maximum character display information • Track name – 32 character maximum • Directory name – 23 character maximum • *Song title – 30 character maximum • *Artist name – 30 character maximum • *Album name – 30 character maximum *Song title, Artist Name, and Album Name, will only be displayed if included with the MP3/WMA file. When referring to MP3/WMA playback, the following terms are synonymous: • File name and track name • Folder name and directory name

Press SRCH for more than three seconds to select between the following modes: • Direct File Select • Alphanumeric File or Folder Search • File or Folder Navigate Press SRCH for more than three seconds, then release. “MP3 T*" or “WMA T*” will flash in the display. Use the buttons in the above table (three keystroke maximum input), or the rotary encoder to enter the desired file number. Press to confirm the selected file number or wait for the input cycle to time out (approximately five seconds). If the file is not available, “NO FILE” will be displayed momentarily and the current file will continue to play. Direct Select, Search and Navigate Modes Direct File Select Step 1 Step 2 Refer to the following button function table when selecting, searching or navigating MP3/WMA files and folders: MP3/WMA Button Function Table Button Function SRCH Direct Select, Search and Navigate Modes Enter/Confirm Preset #1 A, B, C, 1 Preset #2 D, E, F, 2 Preset #3 G, H, I, 3 Preset #4 J, K, L, 4 Preset #5 M, N, O, 5 Preset #6 P, Q, R, 6 Key #7 S, T, U, 7 Key #8 V, W, X, 8 Key #9 Y, Z, /, 9 Key #0 -, _, +, 0 Rotary Encoder (push) Character Shift Rotary Encoder (rotate) Character Select (A, B, C ~ 8, 9, 0) MUTE Character Backspace

Press SRCH again, an "*" will flash in the display. Use the buttons in the table on page 12 (32 character maximum input) or the rotary encoder to enter the desired alphanumeric search characters. Press MUTE to advance one character to the right. Press to initiate the selected alphanumeric search. Turn the rotary encoder to preview the search results. If the search returns a folder, the icon will illuminate. Press to select the desired file or folder. If a folder is selected, "/ /" will be displayed. Turn the rotary encoder to the right to begin searching files in the folder. Press to select the desired file within the folder. Note: If the file is not available, “NO FILE” will be displayed momentarily and the current file will continue to play. Press SRCH for more than three seconds, then release. Press SRCH again two times to navigate files/folders on the disc. The current folder name will scroll one time followed by available files and folders. Turn the rotary encoder to preview files/folders in the current folder. If a folder is selected, the icon will illuminate. Press to select the desired file or folder. If a folder is selected, "/ / " will be displayed. Turn the rotary encoder to the right to begin searching files in the folder. Press to select the desired file within the folder. When navigating folders (and “/ /“ is displayed), press MUTE to access the previous level (up one level). *Only available on MP3/WMA discs recorded with more than one folder. Alphanumeric File or Folder Search Step 1 Step 2 Step 3 Step 4 Step 5 File/Folder Navigate Step 1 Step 2 Step 3 Step 4 *Folder Access (Up one level) CD Player Operation - MP3/WMA Files XDMA6700 OPERATION

XDMA6700 OPERATION Navigating Note *Folder Access File Repeat File Repeat (Current Folder Only) Disc Random Folder Random Disc Intro Folder Intro After navigating by direct select, alphanumeric search or file/folder navigate modes, the track number and elapsed time will be displayed by default. Press DISP momentarily to select clock, track name, directory name, title, artist and album. Press to select the previous folder. Press to select the next folder. *Folder access is only available on MP3/WMA discs recorded with more than one folder. Press RPT momentarily to continuously repeat selected file. Press RPT again to cancel. Press RPT for more than two seconds to consecutively repeat all files in the current folder only. The icon will appear in the display when in folder repeat mode. Press RPT again to cancel. Press RDM momentarily to play all files on entire disc in random order. Press RDM again to cancel. Press RDM for more than two seconds to play all files in current folder only in random order. The icon will appear in the display when in folder random mode. Press RDM again to cancel. Press INT momentarily to play the first 10 seconds of each file on the entire MP3/WMA disc. Press INT again to cancel. Press INT for more than two seconds to play the first 10 seconds of each file in the current folder only. The icon will appear in the display when in folder intro mode. Press INT again to cancel. Note: File repeat (current folder only), folder random and folder intro functions are only available on MP3/WMA discs recorded with more than one folder.

• CD-ROM (ISO), CD-R, CD-RW • CD-DA • MP3 data • WMA data The following types of discs/files are not compatible: • WMA files that are protected by DRM (Digital Rights Management). • WMA lossless format • Discs recorded with Track At Once or packet writing • MP3 PRO format • MP3 playlists • WAV format MP3/WMA playback sequence is based on recorded order of files and begins in the root folder of the disc. Any empty folders or folders that do not include MP3/WMA files are skipped. This unit may not play files in the order they were recorded in. Refer to your recording software’s user manual for more information. • ISO9660 level 1 • ISO9660 level 2 • Yellow Book MODE 1 • Yellow Book MODE 2 FORM 1 • Multi session • Maximum folders and files - 256 • Maximum folder levels - 8 • MPEG-1/2/2.5 Audio Layer - 3 ISO9660 standards: • Maximum nested folder depth is 8 (including the root folder). • Valid characters for folder/file names are letters A-Z (all caps), numbers 0-9, and “_” (underscore). Some characters may not be displayed correctly, depending on the character type. • This device can play back discs in Joliet, Romeo and other standards that conform to ISO9660. MP3/WMA written in the formats other than the above may not play and/or their file names or folder names may not be displayed properly. Media Compatibility Playback Order Compatible Recording Formats CD Player Operation - MP3/WMA Files XDMA6700 OPERATION

An internal buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping. When playing a disc recorded with regular audio files (CD-DA or .WAV) and MP3/WMA files, the unit will play the MP3/WMA files only. Only MP3 files with filename extension (.mp3) can be played. Only WMA files with filename extension (.wma) can be played. Do not attempt to play discs which contain non-MP3/WMA files with the MP3/WMA extension. 8kHz ~ 48kHz 32kHz ~ 48kHz 8kbps ~ 320kbps constant Variable bit rates 32kbps ~ 192kbps constant Variable bit rates Note: Some files may not play or be displayed correctly, depending on sampling rates and bit rates. ID3 tags Version 1.x This model will not display ID3 Version 2.0 or greater tags. For best results, use the following settings when burning an MP3 disc: 128kbps or higher constant bit rate 44.1kHz or higher sampling frequency For best results, use the following settings when burning a WMA disc: 64kbps or higher constant bit rate 32kHz or higher sampling frequency Additional MP3/WMA Information Sampling Frequency Rates MP3 WMA Transfer Bit rates MP3 WMA MP3 Tag Display Recommended Settings

Once connected, press MODE until "IPOD" appears in the display. The iPod will automatically begin playback. If a song is playing on the iPod before it is connected, it will continue to play. Press DISP to select between elapsed time (default), track number, clock, title, artist and album. “UNKNOWN ARTIST” will be displayed if the file contains no artist tag information. “UNKNOWN ALBUM” will be displayed if the file contains no album tag information. Press MENU once to enter the search mode. Turn the rotary encoder to select between playlist, artist, album and song. Press MENU to select the desired search type. Press RTN to to access the previous level (up one level). Turn the rotary encoder to select between playlists. Press MENU to select desired playlist. Turn the rotary encoder to select between songs from the chosen playlist. Press to begin playback. Turn the rotary encoder to select between artists. Press MENU to select desired artist. Turn the rotary encoder to select between albums from the chosen artist. Press MENU to select desired album from the chosen artist. Turn the rotary encoder to select between songs from the chosen album. Press to begin playback. Turn the rotary encoder to select between albums. Press MENU to select desired album. Turn the rotary encoder to select between songs from the chosen album. Press to begin playback. Turn the rotary encoder to select between songs. Press to begin playback. Press ll to skip to the beginning of the next song. Press nn to return to the beginning of the current song. Pressing nn again skips to the beginning of the previous song. Connect iPod (Not Included) Displaying Information Search Functions Playlist Search Artist Name Search Album Name Search Song Name Search Song Select XDMA6700 OPERATION iPod® Operation (Optional)

song. Press l/ II to temporarily stop playback. Press l/ II again to resume playback. Press INT to play the first 10 seconds of each song. Press INT again to cancel. Press RPT to continuously repeat selected song. Press RPT again to cancel. It is not possible to select songs in repeat mode. Press RDM to play all songs in random order. Press RDM again to cancel. Random mode is retained in memory when selecting between Tuner, CD player, Aux, iPod and Bluetooth modes and when the unit is turned on/off. Only alphanumeric characters can be displayed (ASCII type). "NO SUPPORT" will be displayed if the file contains characters that can not be displayed. "NO SONG" will be displayed if there are no songs in the selected playlist. Maximum character display information • Song title – 30 character maximum • *Artist name – 30 character maximum • *Album name – 30 character maximum *Artist Name and Album name will only be displayed if included with the file. The following models are supported: • Third generation iPod - Version 2.3 • Fourth generation iPod - Version 3.1.1 • Fifth generation iPod - Version 1.1.2 • iPod Photo - Version 1.2.1 • iPod Mini - Version 1.4.1 • iPod Nano - Version 1.2.0 Refer to your iPod instruction manual for details on how to obtain the latest software. Fast Forward and Reverse Pause Intro Repeat Random Character Support iPod Compatibility XDMA6700 OPERATION iPod® Operation (Optional)

Overview Connecting a Bluetooth device requires first connecting the Dual BTM60 module (sold separately). When connected to a Dual Bluetooth Ready head unit, the BTM60 supports the HFP (hands-free profile), A2DP (advanced audio distribution profile) and AVRCP (audio video remote control profile). Preparation Before you can use a mobile device with this head unit, it must be connected and authenticated - commonly referred to as "pairing" a device. Please make sure that Bluetooth is activated on your mobile device before you begin the pairing process. Refer to the owner's manual of your mobile device for more details. Bluetooth Pairing 1) To pair a Bluetooth enabled mobile phone to your head unit, press on the head unit or BTM60, or press MODE until "DUAL_BTM60" is displayed. 2) Press and hold on the head unit or the BTM60 for 5 seconds, until "PAIRING" is displayed, the Bluetooth icon will flash every second. The head unit will begin to broadcast a signal for 60 seconds. 3) Complete the pairing from the Bluetooth menu of your mobile device by searching for new devices. Please refer to your mobile device instructions for further information on Bluetooth pairing and connections. The Bluetooth icon will illuminate solid. The BTM60 device name is "DUAL_BTM60." The password for the DUAL BTM60 is 1234. General Notes •Due to the differences in Bluetooth technology, some mobile devices may be incompatible or function improperly when used with the BTM60. •The BTM60 will store the last eight (8) devices that have been paired in its memory. If more than eight devices are paired, the head unit will remove the oldest device from its memory and that device will have to be paired again. Connection Notes •If ACNT is set to OFF, you must press to connect after pairing. •From Bluetooth standby mode, press MUTE to disconnect your mobile device from the BTM60. •From Bluetooth standby mode, press to reconnect your mobile device to the BTM60. •To connect a different mobile device, the currently connected mobile device must be disconnected. If this device has been paired previously, you may reconnect using the mobile device's Bluetooth menu, or repeat the above pairing instructions.

Function Description Making a Phone Call Press once. An "_" will appear on the display. Input the desired phone number using the 0-9, *, # buttons on the head unit front panel. Press to begin dialing. A phone call may also be placed from your mobile device using the keypad, phone book or speed dial. Last Number Dialing To enter last number dialing mode, press , then press a second time. The head unit will display "Last Number Dialing." Press KEY 0 to cycle through the received, dialed or missed call categories. Rotate the rotary encoder to cycle through the last 5 calls in the selected category. Note: You have 5 seconds to make a choice before the head unit returns to Bluetooth standby mode. Press to begin dialing the selected number. Receiving a Phone Call If an incoming call is detected, the head unit will automatically switch to Bluetooth mode, muting any current audio. The incoming phone number will scroll across the display, the phone icon will flash on the display, and a ring tone will be audible from the vehicle speakers. See Bluetooth Settings for speaker configurations. NOTE: The ring audio level will depend the mobile device and head unit ring volume and audio settings. If the ringer on the mobile device is off, you may not hear an incoming ring tone. Press on the head unit or BTM60 to receive a call. The phone icon will illuminate solid. Refusing a Call To refuse an incoming phone call, press and hold MUTE for 3 seconds. During a Phone Call The head unit will display the elapsed time of the phone call. The rotary encoder will adjust the volume of the call. Press MUTE to select between microphone on (MIC ON) and microphone off (MIC OFF). Audio Transfer To transfer the phone call between the head unit and the mobile device, press and hold DISP for 3 seconds during a call. Tip: transfer audio to your mobile device before turning the head unit off. Call Waiting When a second call is incoming, press to activate call waiting. The current call will be placed on hold, and the second call will be active. Press again to return to the first call. Ending a Phone Call Hold MUTE for 3 or more seconds to end a call. If the phone call was received, the head unit will return to previous mode when call is ended.

Menu Function Options Action Bluetooth Mode BT ON Enables the BTM60 Bluetooth Interface Module (sold separately). The Bluetooth icon will flash every 10 seconds. BT OFF Disables Bluetooth support. Auto Connect ACNT ON Allows the BTM60 to automatically (re)connect to the most recently connected mobile device. Note: Some mobile devices do not support this feature. ACNT OFF Disables the auto connect feature. You must press every time to connect a mobile device. Auto Answer AANS OFF Disables the auto answer feature. Press to receive an incoming call. AANS ON All incoming calls will be answered automatically - without notification. Bluetooth Audio SPK 2-CH Directs the Bluetooth audio to the front speakers. SPK 4-CH Directs the Bluetooth audio to all 4 speakers. The BTM60 supports A2DP wireless streaming audio from your Bluetooth mobile device directly to your head unit. You can also control your music from the front panel of the head unit using AVRCP. To stream music to your head unit, your mobile device must support the following criteria: • A2DP profile to stream audio • AVRCP profile to control your music. Check the owner's manual or manufacturer of your device for compatibility. • Streaming audio must be enabled from your mobile device. This option will vary depending on the device. Example: "Set as wireless stereo." • Disabling AV MODE must be done from your mobile device. After enabling streaming audio from a compatible mobile device, the head unit will display "AV MODE." The following functions can be used to control music: • The ll button will skip to the next available audio track. • The nn button will skip to the previous audio track. • The l/ II button will toggle between play and pause during playback. • The MUTE button will stop the audio playback. NOTE: If you are experiencing problems with these functions, try playing music from the mobile device. On some mobile devices, it may be necessary to control the music from the device. Bluetooth Streaming Audio Operation (AV MODE)

This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period. Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A. What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. What to do? 1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call. 2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center. 3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment. 4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods: • Call us toll-free at 1-866-382-5476 • E-mail us at [email protected] Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.

(no power) Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) Black wire not connected Check connection to ground Fuse blown Replace fuse Unit has power (but no sound) Speaker wires not connected Check connections at speakers One or more speaker wires touching each other or touching chassis ground Insulate all bare speaker wires from each other and chassis ground Unit blows fuses Yellow or red wire touching chassis ground Check for pinched wire Speaker wires touching chassis ground Check for pinched wire Incorrect fuse rating Use fuse with correct rating Excessive skipping Unit is not mounted correctly or backstrap is not secure Check mounting sleeve and backstrap support Physical defect in media (CD, CD-R or CD-RW) Check media for scratches ERROR-01 appears on display Disc read error Press eject or RESET ERROR-02 appears on display Focus error or disc is in upside down Press eject or RESET PROTECT appears on display The WMA file is copy-protected by DRM (Digital Rights Management) Write disc using WMA files that are not copy-protected NO FILE appears on display Selected file is not available in direct or alphanumeric search modes Repeat search using valid parameters INVALID appears on display The file format is incompatible Write disc using valid audio files with .mp3 or .wma file extensions Unit will not accept a disc CD mechanism position out of alignment Press and hold EJECT for 3 seconds to reset CD mechanism position CD transit screws still in place Remove 2 transit screws located on top of the unit PAIRING FAILED appears on the display Pairing attempt has exceeded 60 seconds Retry pairing sequence. Pairing must complete within 60 seconds Phone is not setup correctly to connect to a bluetooth hands free device Check the owners manual for instructions on enabling bluetooth Bluetooth device is not compatible with the BTM60 Call 1-866-382-5476 for the latest compatibility information BTM60 reset Reset the BTM60 to clear the memory of previously paired mobile devices and to clear recent dialed/missed/received phone calls from memory From Bluetooth standby mode, press and hold MODE for BTM60 reset. Note: ACNT will be set to OFF after the BTM60 is reset. Troubleshooting - General XDMA6700 OPERATION

Channel separation @ 1kHz: >65dB D/A converter: 1 Bit Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 8.5dBf 50dB quieting sensitivity: 10dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz Tuning range: 530kHz-1710kHz Usable sensitivity: 22uV Frequency response: 30Hz-2.2kHz Operating voltage: 11-16 VDC, negative ground Speaker output impedance: 4~8 ohms Line output voltage: 2 Volts Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm) Design and specifications subject to change without notice. CD Player FM Tuner AM Tuner General CEA-2006 Power Standard Specifications (reference: 14.4VDC +/- 0.2V, 20Hz~20kHz) Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms) Dual Electronics Corp. Toll Free: 1-866-382-5476 www.dualav.com ©2007 Dual Electronics Corp. All rights reserved. Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and or other countries. iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Movon is under license. Other trademarks and trade names are those of their respective owners. NSA0307-V01