Sealey WB951LED Instructions

and properly maintained, give you years of trouble free performance. 1. SAFETY INSTRUCTIONS IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. 1.1 GENERAL SAFETY Familiarise yourself with this product's application and limitations, as well as any specific potential hazards peculiar to the beacon. Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty. DO NOT use the beacon for any purpose other than for which it is designed. DO NOT allow children to operate the beacon. DO NOT operate the beacon if any parts are missing or damaged as this may cause failure or possible personal injury. When not in use switch the beacon off and where appropriate remove plug from power supply. 2. TECHNICAL SPECIFICATIONS Voltage:...................................................................................12V-24V dc Current:..........................................................................................450mA Number of LEDs: .................................................................................. 40 Index of protection (EN 60598-1): .....................................................IP56 Operating Temperature:....................................................-30°C to +50°C Radio Interference Filter:.......................... ......... EC95/54 EMC approved Approvals:......................................................................................ECE65 3 . INTRODUCTION Model No’s: WB951LED,WB952LED,WB953LED,WB954LED,WB955LED INSTRuCTIONS FOR: LED WARNING BEACONS 12/24Volt VARIOUS FITTINGS Heavy-duty ABS bases. Quick release uV stabilised domes will not fade when exposed to sunlight. Features 40 LEDs for an increased output of light. 3-Function control allows for different LED configuration depending on operation. CE Approved and E-Marked. WB951LED ø128mm Overall height: 200mm Length of mounting: 40mm WB952LED ø140mm Height: 190mm WB953LED ø128mm Height: 200mm WB955LED ø128mm Height: 250mm ø140mm Height: 170mm WB954LED WB951LED,WB951LED,WB953LED, WB954LED,WB955LED ISSuE: 1 12/12/13 Original Language Version © Jack Sealey Limited

All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. 4. FIxING INSTRUCTIONS 4.1 WB951LED: 12mm Single Bolt Fixing 4.1.1. Drill a 13mm mounting hole in a suitable point on the vehicle. 4.1.2. Connect to cables of at least 2mm² section and use an 8A fuse; check polarities. 4.1.3. Fix the beacon by using nuts and washers according to the type and shape of the mounting surface 4.2 WB952LED: Three Bolt Fixing Base 4.2.1. Drill mounting holes using the beacon base as a template. Also make provision to route cables into the vehicle. 4.2.2. Connect to cables of at least 2mm² section and use an 8A fuse; check polarities. 4.2.3. Fix the beacon with 3 x M6 screws. 4.3 WB953LED: Fixed Spigot Base ●� Use�in�connection�with�DIN�spigot (a range of DIN mountings is available: please see Sealey catalogue). ●� DIN�adaptor�mounts�to�vehicle�allowing�removal/installation�without�tools. ●� Suitable�for�situations�where�security�is�a�problem. 4.3.1. Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical. 4.3.2. use cables of at least 2mm² section and use an 8A fuse; check polarities. 4.3.3. Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut. 4.3.4. When the beacon is removed, always close the adapter socket outlet using the rubber cap. 4.4 WB954LED: Magnetic Base ●� Fitted�with�high�power�magnet�strong�enough�to�cope�with�normal�road�speeds. ●� Supplied�with�3mtr�coiled�flex�and�universal�auxiliary�power�outlet�plug. 4.4.1. The beacon must be placed on a surface parallel to the ground. 3.4.2. The surface should be flat and clean to ensure good adherence. 4.5 WB955LED: Flexible Base with DIN Spigot Mounting. 4.5.1. Fit a suitable adapter socket onto the vehicle. Make sure it is perfectly vertical. 4.5.2. use cables of at least 2mm² section and use an 8A fuse; check polarities. 4.5.3. Push the beacon spigot down fully onto the adapter socket and secure by tightening the wing nut. 4.5.4. When the beacon is removed, always close the adapter socket outlet using the rubber cap. The beacons will switch between 12V and 24V automatically. 6.1. Three flash patterns are available by selecting one of the three switch positions as in fig.2. The switch is accessed by removing the dome as in fig.1. 6.2. Switch 1: Rotating flash; flash rotates mimicking a rotary beacon. Switch 2: Six rapid flashes followed by a break. Switch 3: Two flashes followed by a break. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No responsibility is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from purchase date. Proof of purchase will be required for any claim. INFORMATION: Please call us for a copy of our latest catalogue on 01284 757525, leaving your name, address and postcode. Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk 6. FLASH PATTERN SELECTION 5. VOLTAGE SELECTION fig.1 fig.2 WEEE Regulations. Dispose of this product at the end of its working life in compliance with the Eu Directive on Waste Electrical and Electronic Equipment. When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information. WB951LED,WB951LED,WB953LED, WB954LED,WB955LED ISSuE: 1 12/12/13 Original Language Version © Jack Sealey Limited