Sealey TJ150E Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. 1. SAFETY INSTRUCTIONS 2. INTRODUCTION & SPECIFICATION � Maintain the jack in good condition (use an authorised service agent). � Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. � Locate the jack in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the jack and the transmission unit. DO NOT operate the jack on tarmacadam, as the surface may be unstable. � Keep the jack clean for best and safest performance. � The maximum transmission unit weight is 150kg. DO NOT exceed this rated capacity. � Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair. � Keep hands and fingers clear of the scissor mechanism during use. � Maintain correct balance and footing, DO NOT over reach. Ensure that the floor is not slippery and wear non-slip shoes. � Keep children and unauthorised persons away from the work area. � DO NOT use the jack for a task it is not designed to perform. � DO NOT use the jack as a vehicle lifting device. � DO NOT operate the jack if damaged. � DO NOT operate the jack when you are tired or under the influence of alcohol, drugs or intoxicating medication. � DO NOT allow untrained persons to operate the jack. � DO NOT make any modifications to the jack. � Before storing, ensure that all parts are clean and the jack is fully lowered. Store jack in a safe, dry, childproof area.  WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. 3. OPERATING INSTRUCTIONS Model No: .................................................TJ150E Capacity: ..................................................... 150kg Minimum Saddle Height:...........................195mm Maximum Saddle Height:..........................585mm Base Dimensions: ........................... 400 x 420mm Ratchet Drive Socket Size: .................. ½" Square ●� Suitable�for�raising�and�lowering�gearbox�and�differential�units. ●� Easy�to�operate�scissor�mechanism�for�precision�when�fitting�the�transmission�unit.� ●� The�saddle�is�fitted�with�a�webbing�strap�with�metal�roller�buckle�to�hold�the�load�securely�and�has�a�5°�tilt�adjustment. ●� Four�heavy-duty�castors�provide�flexibility�of�movement�within�the�workplace. Refer to fig.2. 3.1. Ensure that the vehicle being worked on is securely immobilised. If any wheels are removed it MUST be supported securely on axle stands. NEVER WORK UNDER A VEHICLE SUPPORTED BY A JACK ONLY. 3.2. Unfasten the webbing strap and roll the jack to immediately below the unit to be removed. 3.3. Using a ½" ratchet drive inserted into the drive socket, raise the saddle into light contact with the load. DO NOT use an impact wrench with this product. 3.4 The�saddle�may�be�tilted�by�up�to�5°�to�allow�better�registration�with�the�transmission�unit�being�removed. Slacken the wingnuts on both sides to allow adjustment of the saddle and re-tighten to lock in position. DO NOT attempt to adjust tilt whilst under load. fig.1 Original Language Version © Jack Sealey Ltd © Jack Sealey Ltd TJ150E Issue: 1 13/12/12

without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. 01284 757500 01284 703534 [email protected] www.sealey.co.uk Web email 3.5. Secure the transmission unit to the saddle using the webbing strap and remove fastenings holding the transmission unit to the vehicle. It may be neccessary to maneouvre the jack gently to allow the fastenings to be withdrawn cleanly. 3.6. When the transmission unit is free, reverse the ratchet to lower the saddle allowing removal from beneath the vehicle. 3.7. It is recommended that, for maximum stability, the saddle is lowered fully before moving under load. 3.8. Re-installation is the reverse of the above proceedure. fig.2 4.1. Apply a good-quality grease periodically to all moving parts, paying particular attention to the lead screw (fig.2). 4.2. Replace the securing strap if it becomes torn or damaged in any way. Original Language Version © Jack Sealey Ltd © Jack Sealey Ltd TJ150E Issue: 1 13/12/12 Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR