Duerkopp Adler 512/532 Operating Manual

13 4 Operating manual 4.1 Threading the needle thread 1. Put the thread reel on the thread stand and guide the needle thread and the hook thread through the unwinder arm. • The unwinder arm must be in a horizontal position above the thread reels. 2. Thread the needle thread as illustrated in the following figure. Fig. 1: Threading the needle thread 3. After threading, pull about 4 cm of the needle thread out through the needle. This guarantees a safe start to sewing. 4. If you are using silicone oil, additionally thread the ne ...

Potsdamer Str. 190 D-33719 Bielefeld Germany Phone +49 (0) 521 925 00 E-Mail: [email protected] www.duerkopp-adler.com Subject to design changes - Printed in Germany - © Dürkopp Adler AG - Original Instructions - 0791 512741 - 01.0 - EN - 03/2013 ...

5 2 Safety instructions This chapter contains basic instructions for your safety. Read these instructions carefully before you install, program, maintain or operate the machine. Always follow the provisions in the safety instructions. Failure to observe can lead to severe injury and damage to property. 2.1 General Safety Precautions Only authorised persons must work on or with the machine. Every person working on or with the machine must read the Operating Guide before do- ing so. The machine must only be used as described in ...

Operating manual 512/532 Version 01.0 - 03/2013 33 Fig. 13: Stitch coordinates in MS Excel or in a text editor 1. Entering stitch coordinates. The coordinates are accurate to a precision of 0.1 mm and are thus separated in an MS Excel table, or comma-separated in a text editor. Note: For stitch coordinates in the text editor, the last line of coordinates must be terminated with a line end so that the cursor sits in the next empty line. 2. Memorize the file. • File name: HSR2000 ~ HSR2099 • File format: CSV 3. Memorize the file on a USB stick. ...

13 4 Operating manual 4.1 Threading the needle thread 1. Put the thread reel on the thread stand and guide the needle thread and the hook thread through the unwinder arm. • The unwinder arm must be in a horizontal position above the thread reels. 2. Thread the needle thread as illustrated in the following figure. Fig. 1: Threading the needle thread 3. After threading, pull about 4 cm of the needle thread out through the needle. This guarantees a safe start to sewing. 4. If you are using silicone oil, additionally thread the ne ...

53 8.3.7 Fitting the collecting container Fig. 24: Fitting the collecting container 1. Place the bracket (2) in the drill hole on the table top (6) and fasten with 3 screws (1). 2. Bolt the oil catchment container (5) onto bracket (2). 3. Insert the oil line (3) into the oil catchment container (5) 4. Push the rubber supports (4) into the table top (6). 8.4 Electrical connections 5 6 1 2 3 4 (1) - Screw (2) - Bracket (3) - Oil line (4) - Rubber support (in the oil catchment tray) (5) - Oil catchment container Risk of in ...

15 4.3 Adjusting the thread regulator Fig. 3: Adjusting the thread regulator The thread regulator (3) controls the quantity of needle thread required for stitch formation. The thread regulator must be precisely adjusted for an optimum result. With correct setting the needle-thread loop must slide with low tension over the thickest point of the hook. 1. Release the screw (1). 2. Adjusting the position of the thread regulator (3). Thread regulator to the left = more needle thread Thread regulator to the right = less needle thread ...

Operating manual 512/532 Version 01.0 - 03/2013 25 5.4 Scaling axes 5.4.1 Changing the X-axis 1. Press the Selection button until the X-axis LED is lit. 2. Press the +/- Function key until you reach the X-axis value. 100 % corresponds to the stated dimensions for the selected sewing pattern. 5.4.2 Changing the Y-axis 1. Press the Selection button until the Y-axis LED is lit. 2. Press the +/- Function button until you reach the Y-axis value. 100 % corresponds to the stated dimensions for the selected sewing pattern. 5.4.3 Converting the buttonhole gap (class 532) The butto ...