TEUCER LR-TW Quick Start Manual
Text of the manual
Single Zone Controller - LR-TW
page 1
Feature
* Touch sensitive remote & colour Wheel
* 20 Automatic Play modes to choose from
* Last settings memory function when powered On
Parameter
PART NO.
INPUT
VOLTAGE
OPERATION
FREQUENCY
DIMENSIONS
(mm)
REMARKS
LR-TW
3.6VDC
2.4GHZ
52x110x20
2xAAA
BATTERIES
Product Size
The single zone Tunable white controller enables control of the tunable
white LED Strip lighting. This remote allows the user to access 3 pre-set
lighting levels from the touch of a button and adjust the lighting levels
with smooth dimming (5%-100%) via the touch sensitive wheel.
* 5%-100% Smooth Dimming
Remote
Reciever
PART NO.
INPUT
VOLTAGE
CURRENT
OUTPUT
REMARKS
LRR-TW
12-24VDC
2x6A
2x(72-144)W
RF
Receiver
52mm
110mm
20mm
* Dimming & colour changing
* Wireless RF range of 10 - 20 meters (Dependent
on signal obstacles within the installation area)
* Remote and receiver supplied together as
standard
Reciever Wiring Diagram
RF technology allows for great flexibility when it comes to controlling simple or complex lighting installations
without the need of wiring. There are limitations in some cases due to receivers installed in enclosed
electrical boxes or in ceiling voids hence reducing the RF signal strength and the communication range.
In order to overcome these RF signal restrictions we suggest the following procedure when synchronising
our RF controllers and receivers:
*Keep the distance between the controller and the receiver within10 meters.
*When expanding your lighting, we recommend the use of ‘power repeater's, if synchronisation of the
additional strips is required.
*Never synchronise more than 4 receivers to a single zone (if kept on a single colour).
*Never synchronise more than 1 receiver to a single zone.
The controller & receiver do not have a MASTER / SLAVE function, meaning if you connect several
receivers to the same controller, the LED Strip will become unsynchronised when put into a colour
changing programme.
on
off
ON Button
Brightness low
High Brightness
Low Brightness
High Brightness
Medium Brightness
OFF Button
Warm White colour temperature
White colour temperature
Synchronising The Remote To Receiver
Page 3
Please Note: All controllers & receivers sold in a pack are pre-synchronised. There is no need to sync the
remote to the receiver.
*Only follow the instructions below if you are adding another receiver with the same remote
NOTE: Steps 2 & 3 must be conducted within 2 seconds. Make sure power to the receiver is switched
off before step 1
Insert 2 x AAA working batteries in the remote. This will ensure the Remote is powered up.
Turn ON the power to the Driver / Receiver. (depending on which accessory the Strip is
connected to.
1) Ensure the Remote has power
2) Turn the LED Strip ON
3) Press the “high brightness” button on the Remote.
4) The LED Strip will flash twice if the synchronisation is successful.
5) Just repeat the learning process to synchronise several receivers to the same controller.
6) To clear the synchronisation, simply press the “High Brightness” button three times after switching
on the LED Strip.
on
off
High Brightness
Brighter For Longer
page 4
Safety and Warnings
Products must be installed and serviced by qualified electrician
* Please ensure this product is mounted in a water proof enclosure
* Always ensure products are mounted in areas with adequate ventilation to avoid any overheating.
* Please ensure outputs of any power supplies used in conjunction with this product comply with its working voltage.
* Never install product whilst connected to power and double check connections before switching on to avoid short
circuits.
* For any further help or advice please contact Teucer on 0207 350 4429 or find us online at
www.teucerled.co.uk
* Any defects caused by negligence, high temperature, humidity or harmful chemicals.
* Damage caused by transport, Fire or abnormal voltage surges.
Warranty Agreement
* 3 Year Warranty: This warranty is for free repair and replacement of the product and covers manufacturing faults
only.
* Any faults beyond warranty boundaries are subject to charge for parts and labour.
Warranty Limitations
1) Turning the LED Strip ON and OFF
2) Adjusting the Brightness of the LED Strip
Warm White
Cool White
Dim Down
Dim UP
Use the ON and OFF buttons on the remote to witch the LED Strip ON and OFF.
Use the Dimming Ring by lightly sliding your finger around the ring to adjust the brightness of the Strip
Controlling Your LED Strip
