RGBlink FLEXpro 8 Operation & User’s Manual

Installation Safety Summary............................................................................................................... 4 Chapter 1 Your Product................................................................................................................................6 1.1 In the Box.........................................................................................................................................6 1.2 Product Overview...........................................................................................................................7 1.2.1 Front Panel..............................................................................................................................8 1.2.2 Rear Panel............................................................................................................................... 9 1.2.3 Dimension.............................................................................................................................10 Chapter 2 Install Your Product..................................................................................................................11 2.1 Plug in Signals.............................................................................................................................. 11 2.2 Plug in Main Power...................................................................................................................... 11 2.3 Turn on Your Product.................................................................................................................. 11 2.4 Connect Felxpro 8 and Computer...............................................................................................11 Chapter 3 Use Your Product......................................................................................................................12 3.1 Install XPOSE 2.0.............................................................................................................................. 12 3.2 XPOSE Controls Felxpro 8................................................................................................................ 16 3.2.1 Login in XPOSE...................................................................................................................... 16 3.2.2 Topology Diagram.................................................................................................................18 3.2.3 Input and Output Settings....................................................................................................22 Connect the Device........................................................................................................................22 Output Setting............................................................................................................................... 23 Input Setting...................................................................................................................................26 Device Overview............................................................................................................................ 33 3.2.4 Display System...................................................................................................................... 35 3.2.5 Layer Management...............................................................................................................40 3.2.6 Preset Management............................................................................................................. 45 3.2.7 Keyboard Setting...................................................................................................................51 3.2.8 System Setting...................................................................................................................... 53 Chapter 4 Order Codes..............................................................................................................................55 4.1 Product.............................................................................................................................................55 4.2 Options.............................................................................................................................................55 4.2.1 Input Options........................................................................................................................55 4.2.2 Output Options.....................................................................................................................55 4.2.3 Other.....................................................................................................................................55 Chapter 5 Support.......................................................................................................................................56 5.1 Contact Us.....................................................................................................................................56 Chapter 6 Appendix.................................................................................................................................... 57 6.1 Specification..................................................................................................................................57

6.3 Revision History............................................................................................................................68

This User Manual is designed to show you how to use this video processor quickly and make use of all the features. Please read all directions and instructions carefully before using this product. Declarations FCC/Warranty Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference. Guarantee and Compensation RGBlink provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults. RGBlink must be informed immediately in writing of any complains. The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant, RGBlink can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other service provided by RGBlink, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of RGBlink. If the purchaser or a third party carries out modifications or repairs on goods delivered by RGBlink, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by RGBlink either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.

The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed. Power Source This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply conductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the power cord is essential for safe operation. Grounding the Product This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired receptacle before connecting to the product input or output terminals. A protective-ground connection by way of the grounding conductor in the power cord is essential for safe operation. Use the Proper Power Cord Use only the power cord and connector specified for your product. Use only a power cord that is in good condition. Refer cord and connector changes to qualified service personnel. Use the Proper Fuse To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer fuse replacement to qualified service personnel. Do Not Operate in Explosive Atmospheres To avoid explosion, do not operate this product in an explosive atmosphere. Installation Safety Summary Safety Precautions For all Felxpro 8 processor installation procedures, please observe the following important safety and handling rules to avoid damage to yourself and the equipment. To protect users from electric shock, ensure that the chassis connects to earth via the ground wire provided in the AC power Cord. The AC Socket-outlet should be installed near the equipment and be easily accessible.

Before opening Felxpro 8 processor shipping box, inspect it for damage. If you find any damage, notify the shipping carrier immediately for all claims adjustments. As you open the box, compare its contents against the packing slip. If you find any shortages, contact your sales representative. Once you have removed all the components from their packaging and checked that all the listed components are present, visually inspect the system to ensure there was no damage during shipping. If there is damage, notify the shipping carrier immediately for all claims adjustments. Site Preparation The environment in which you install your Felxpro 8 should be clean, properly lit, free from static, and have adequate power, ventilation, and space for all components.

1.1 In the Box Note: AC Power Cable supplied as standard according to destination market. Upgrade tool package and user manual are stored in the USB disk, please keep it. Network Cable HDMI to DVI Cable RJ11 to DB9 Serial Cable Antistatic Bag SDI Cable DVI Cable USB Disk

FLEXpro8 is an all new video processing solution for modern large scale display applications. With support for over 18 mega pixels across eight outputs, FLEXpro8 is designed for professional applications. Fit up to 16 independent inputs integrating a range of video sources and signals utilized in commercial display systems. The innovative RGBlink modular signal system provides native on support for HDBaseT, Fiber and LED Control signals as well as conventional signals, embracing flexibility while being an efficient self-contained system. Whether for integration or proAV FLEXpro8 has the multi-signal, multi-layer technology for virtually any display application. Flexpro 8 Application Diagram

1 OLED Panel Show the input shot and output slot information, device status, COM. Version, IP address and serial address. 2 POWER Power button, long push the button, the device can be boot up. Under normal running state, push the button once, the info shown on OLED can be refreshed once ; long push the button, the OLED will pop up a confirm box, release the power button, push the power again before the confirm box disappears, and the power can be turned off.

Chassis Module Structure 1 2 slots for input modules, support DVI, HDMI and SDI optional module 4 Communication 2 2 slots for output modules, support DVI, HDMI, SDI, HDBaseT and Subito Sender optional modules 5 Genlock 3 Independent PVW output ports 6 PSU Module

2.1 Plug in Signals Connect signals to the product (ensure all the device are all power off first).Tighten connector screws/locks where provided. 2.2 Plug in Main Power Connect IEC cable to device and plug into wall socket. Turn on power at wall socket. 2.3 Turn on Your Product Turn on the power switch on the real panel. OLED display will show as below,completing initialization before loading the latest settings and input/output configuration. The system begins to work,and the OLED module shows the input slot and output slot information, device status, COM. Versions. IP address and serial number. 2.4 Connect Felxpro 8 and Computer Use network cable to connect the Felxpro 8 and computer with USBA-B cable from In the Box. Set the IP address of the computer and make sure the computer and the device are in same network range. IP address of the device is available on the OLED screen after it is powered on. For example if the IP of the device is 192.168.110.1, just make sure the IP of the computer is in 192.168.xxx.x, but not exact the same as the device.

3.1 Install XPOSE 2.0 Environment Requirements: Window Processor: 1 GHz or above 32 bit or 64 bit processor Memory: 4 GB or more Graphics: Support DirectX 9 128M or above (open AERO effect) Hard disk space: Above 16G (primary partitions, NTFS format) Monitor: Resolution must be 1920x1080 pixel or above (it can not display normally if the resolution is lower than 1920x1080) Operating system: Windows 7 or above (full version, not Ghost version or compact version) CPU:i5 and above Mac Monitor: Resolution must be 1680x1050 pixel or above (it can not display normally if the resolution is lower than 1680x1050) CPU:i5 and above Double click ,it will pop-up the installer language box, select the language, for example, select “English”, and click “OK” to confirm. Click “Next” to install:

Click “Install”: During installation, it will pop up the window of Install Shield Wizard for Virtual Com port:

Then click “Install", as shown in the figure below:

Click “Finish” and is ready to run the XPOSE :

3.2.1 Login in XPOSE Double click this icon ,and enter the log on interface as follow The initial language of XPOSE2.0 is self adjusted based on the operation system language of the computer. Click Register and fill in the blank with first name, last name, email, company and country and then click Register Now. Registration complete. Please note that the email shall be invalid and complete otherwise registration cannot be completed. Click Activate and scan the QR code an email from RGBlink Registrations will be sent to the Register email address.

Keep the user name as “Admin” and password blank and then click Start Now. Note: If exact Name and Password are needed, users can set up them in Authorization Setting under System Setting. After login, users can find the management including:Topology Diagram,Search,Display System, Layer Management, Preset Management, Keyboard Settings. The details of each hierarchy will be described hereafter. In the following text, we are going to show how to use XPOSE 2.0 to control Felxpro 8.

XPOSE 2.0 offers the feature of making topology diagram which can assist users to import the actual input and output connection into XPOSE control. 1. Drag device, input source device and output device from the list on the left based on the field application. For example, drag Flexpro 8 from Device, Laptop from Input and LDC from Output list as follows: 2. Click the icon at the right bottom corner and open the setting interface as following: 2.1. After Flexpro 8 is dragged into the topology diagram interface, users can find how many Flexpro 8 devices currently linked in the same network from the drop-down arrow after SN.

address of the chosen one. 2.2 In and Out port will show according to the topology diagram. For example topology diagram as follow: The chosen port of board of In and Out indicated by red dot as below:

4. If there are not enough devices in the device list on the left column, users can select and load more devices to the list from the Library.

Connect the Device After Topology Diagram is finished, users can move to next step, the exact setting on each input and output board. Click icon and enter the operation interface. First, choose the device from All Devices for example Flexpro 8 SN:ffff Then click icon behind Flexpro 8 in Chosen Device,IP and SN of this device is shown on the left top corner of the interface ,which indicates that the device is connected to the computer and it can be operated by XPOSE 2.0 from now on.

the port now. A red rectangle flashes around the chosen port when it is clicked. 2.1 After 2K DVI or HDMI port is selected, users can do the following settings in the edit section after clicking icon , Resolution setting, Test Pattern, DE Setting, OSD Setting. 2.1.1 Resolution Setting Output Switch: Slide On or OFF Format Rage: Slide to select ALL or Module. (For output modules on Flexpro, there is no difference between selecting All or Module as there is only one port on each each module) Format Type:Standard or Customize.

If Customize is chosen, users can put in desired resolution (Width, Height, Refresh Rate) based on field application. 2.1.2 Test Pattern slide ON/OFF the Status. After slide ON the test pattern. 2.1.3 DE Setting Output Port：choose current port HDMI Output Type: DVI or HDMI Color Range: Image or Video Bits：8 bits for DV, 8bits/10bits/12bits for HDMI Brightness：0-128 2.1.4 OSD Setting： Output port: the current port

X/Y:the starting horizontal and vertical position Width/Height:the horizontal and vertical size of the text Font：font of the text,all fonts installed in the computer is available Font Type：Normal,Italic,Bold,Bold Italic Font size：0-300 pixels Pixel alignment：Left, Right, Center to Horizontal,Vertical Center Right, Align Bottom Right, Align left bottom, Vertical center left, Vertical center, Horizontal center bottom Font Transparent, Background Transparent Scroll Speed：0-16 Scroll Direction：Scroll Off, Scroll Left, Scroll Right Input Text:The exact content of the text. After setting, users choose Save OSD,Clear OSD(if the setting is not desired) or Close All OSD.

settings to the board now. A red rectangle flashes around the chosen port when it is clicked. 2.1 When DVI is chosen, Property, EDID Setting could be done. 2.1.1 Property Input Port：Current port Source:CVBS,YPbPr, VGA, DVI (DVI module for Flexpro 8 support for CVBS,YPbPr, VGA signal via adapter) Scale X/Y：Vertical and horizontal position Width/Height：Vertical and horizontal size Crop： Left:crop left Top:crop top Width:horizontal size after crop Height:vertical size after crop Display mode：Live or Freeze Picture Adjustment Mirror：ON or OFF Alpha：transparency adjustment, range from 0~128. Mini Delay mode:On or Off. Select this mode on the output and input is simultaneously, without refresh rate delay. Under this mode, the image is under the best state. Saturation：slide to adjust Hue：slide to adjust Color Temperature Red：Slide to adjust Green：Slide to adjust Blue：Slide to adjust

Green：Slide to adjust Blue：Slide to adjust

Customized EDID EDID Template : RGB-DVI and RGB-HDMI to choose White Height Frequency: automatically show current port. 2.2 When 2K HDMI port is select, users can do setting of Property and EDID 2.3When 12G SDI port is select, users can do setting of Property , DSK, LOGO and Source Merge. 2.3.1 DSK Setting： Input Port:Current Port Preset：Customize,White on Black 1,White on Black 2,Black on White 1,Black on White 2,Green on Black 1,Green on Black 2,Green on White 1,Green on White 2,Red on Black 1,Red on Black 2,Red on White 1,Red on White 2 DSK Setting switch：On or Off Operation Mode：0 or 1,automatically show according to user’s Preset choice Transparent：0-255,automatically show according to user’s Preset choice

Red, Green Min：0-255,automatically show according to user’s Preset choice 2.3.2 Logo Input Port：Current Port Select Logo capture or Set Logo Logo Catpure Logo ID：select from Logo1-Logo10 Slide to enable Logo capture Set Logo Logo ID: select from Logo1-Logo 10 Slide to enable Show Logo

2.6 Select any port is selected of 4K board (HDMI 2.0, HDMI 1.4, DP, Dual Link DVI ) There comes Property,4K Setting ,EDID Setting 2.6.1 EDID Setting Input Port Current Port and Type Customized EDID EDID Template：RGB-DVI ortRGB-HDMI Width, Height, Frequency:current

Input Module: current module position Operation mode: 4K x 2K, 4K x 1K, 2K x 1K, PIP 4K x 2K Input type 1: select from DVI, HDMI and DP Splice Height: no more than 2160 4K x 1K

Splice Width 1& Splice Width 2: no more than 10000 2K x 1K Input type 1&Input type 2: select from DVI, HDMI and DP PIP Select Main and Subsidiary picture from DVI,HDMI,DP

Overview show Device Info, board info in each slot. IP：select Auto IP addres or manually type in the IP address, MASK and Gateway Factory setting：Remove Logo and/or Remove EDID Power on：0-255S Fan Control：Auto adjustment,Fan speed 0-99

Display System is for users to set layout of outputs. Click this icon first and then click enter the interface as follow: Template： There are 16 types of basic “Display Area” which is used to contain output interface,and could be regarded as layout of output. Drag a layout for example 2x4 (4680x2160) from the template list to the middle interface.

XPOSE 2.0 allows multiple modes running on one same interface, to differentiate each mode, different color is given to each mode. Click this icon to cancel the monitor in Display Area Long pressing this icon to cancel the Display Area Use the bar under the interface and type in the parameter to set resolution and position of monitor

below template, user can type in the width, height ,Row and Column, according to actual display in field, click .It will automatically calculate the width and height of each monitor based on the parameter above, as the following example, creat a 4000x2000 display area. To save this display area, just click Used: Show the already used or saved “Display Area”, all the used “Display Area” can be kept unless users “Delete All” Monitor Show all the output ports (monitors) of this device. If the monitor is in dark (black), it indicates that this monitor is used, otherwise it is in grey.

PST|PGM, Matrix|Aux, Parameter works the same as the bar under interface. Parameter under under the mode of Presentation, PST|PGM, Matrix|Aux mode LED cabinet Flexpro8 support to install RGBLink Subito sender designed to take direct control LED display. Led cabinet is offered to do cabinet settings.

Drag the boarder of the display area to move its place in the interface. Click icon to shrink,Click to enlarge the proportion of display area on interface.

Layer Management is designed to manage the layer of each monitor. Click this icon to enter the interface: Display Area Here is to show all the Display Area set in previous step System Management. Click to cancel or use the corresponding Display Area. Signal To show the signal list of 16 inputs. Drag source from signal list to monitor Numbers on Monitor Numbers on monitor is to show how many layers at present allowed to put in the monitor . Each monitor (output port) can contain layers no more than 4. Any 1 input signal cross 1 border of a monitor is regarded as 2 layers.

1. Use the bar under the interface Choose one layer and the bar shows its signal source, type in position and size. 2. Layer Scale or Crop Layer Movement Place the cursor on the layer, it turns to a palm icon , press the left of mouse, the icon turns to a fist , moving the mouse can drag the layer.

Layer Max Click this icon , to cover up all monitors in the same Display Area with the one signal, as the following: Layer Copy Press Ctrl and mouse left at the same time, move the mouse the layer selected can be copied and place in any monitor in the same Display Area but it doesn’t work when cross over display area.

When the layer is locked, any movement or removal to the layer is invalid H.264 Slide H.264 to ON Module Index: H.264 Image Quality: to choose from 1:1,1:2,1:3,1:4,1:5,1:6, the higher the ratio the better the preview input image but if band width of network is not good enough, high ratio image quality may cause problem. We usually suggest user to choose 1:4 as the attached picture.

Save to Bank Automatically When one Bank (where the set is contained) is finished, click next Bank, previous set is saved to bank.

Preset Management is designed to switch bank (scene setting done in last step). Preset Management Mode：1 Manual Mode, 2 Schedule Mode Manual Mode Fade Time 0.0-10.0S Black out, slide to ON or OFF The tick on the bank indicates that the bank is selected. Cut|Take Cut, switch from PST to PGM without any effect. Take, switch from PST to PGM with chosen effect in set Fade Time. Transition Effect

Slide Disply to ON , Click and select the Display Area when users need to switch scene from eg. Bank 1 to Bank 2 but want to keep Display Area 2 and 3 the same as Bank 1. Follow the steps below to do the setting. Step1: click Bank 2 and open Display Area Step 2: click the icon behind to cancel the display area of 2 and 3 and click to confirm, Step 3:TAKE or Cut Keep|Swap Only when separate Display switching is OFF can Keep|Swap work. Under the Keep status, users need to select a bank and use Cut or Take to switch image from PST to PGM. Under Swap status, users select a bank, then use Take or Cut to swap this bank and the bank before this one.

Save Bank to Page Select a bank,click Page,select Page X,the bank is saved in the page. The page turns green then become grey, indicating the bank is saved in the page. Load bank from Page Click Load Page, pages with bank saved are green, select one from them and the selected one becomes red. The bank is loaded from page to PST. Script Save and Load Save Script Click ,fill in the blank with the name of setting and Save Load and Delete Script After the script is saved, the bank name will appear in the load list. Select the file and click Load Select the file and click Delete, the chose file can be deleted from list.

(Bank) Click the color block after Color Selection and choose a new color for the boarder of chosen bank. For exmaple change Bank1to RBGLINK, with green boader Display Area is to let users to choose which display areas to display on the PGM and allow users to set transition effect for each display area so that they can switch from PST to PGM in desired effect.

Schedule Mode This mode is designed to set auto bank (scene/preset) switch. Loop Click under , select a bank and set Start Time and End Time. Click OK , the bank will be added to the loop list on the left. Enable Loop to On

(Note, Loop need to be disabled first, if a bank need to be removed from loop list)

Keyboard setting is designed to fit for different operation systems such as Windows and Mac. Users can set short cut keys for Input, Output, Layer and Preset. Drag Input, Output, Layer and Preset from the list to the keys you desired as follow: Input, Output, Layer and Preset. Please note the keyboard area where allows to set short cut keys as follow: If the setting goes wrong or no need for short cut keys any more, click to clear some keys or clear all. Clear: is to clear some keys, the keys need to selected before hand. Clear all: is to remove all already set short cut keys.

Click this icon and enter the interface System Info,Software Version and Language options with English and Russia to choose. Communication Setting,this is to decide how XPOSE to communicate with the device By serial port,ethernet connection,or both are chosen Find Device：choose the devices that users need to be connected Authorization setting：type in the password and to set up subordinate user’s authorization. Display Setting：Slide Expanding Mode to On, 16 displays can be viewed on XPOSE. Slave Unit： Slave Unit is to control multiple devices simultaneously, which are connected to same network. (“In the same network” means the the the third section in the IP address digits are the same )

there are two devices linked to the same network, one with IP IP192.168.0.112 SN 0027, the other 192.168.0.129 SN 3344 as followed: If users need to back up operation from current running device 3344 to 0027, slave unit shall be used. First fill in the quantity of to be linked devices, click Set Numbers, Index, Device IP and State will come up. Fill in the blank with the IP address of the other device, e.g 0027,IP192.168.0.112 and click ON , the red dot behind turns to green indicating that the device has been connected Click OFF , the connection is cut off.

4.1 Product 710-1008-01-0 Felxpro 8 4.2 Options 4.2.1 Input Options 4.2.2 Output Options 4.2.3 Other 190-1001-09-0 Single HDBaseT Input Module-Dual Bracket 190-0001-10-2 Single USB Input and Backup Module 190-0001-07-2 Single 3G-SDI Input/ Loop Module 190-0001-13-2 Single HDMI Input Module 190-0001-04-2 Single DVI Input Module 790-0001-22-0 Single HDMI Output Module 790-0001-21-0 Single DVI Output Module 790-0001-24-0 3G SDI Output Module 790-0001-27-0 Single DP Output Module 790-1001-28-0 Subito Quatro Sender 190-1001-29-0 Single HDBaseT Output Module-Dual Bracket 980-000X-01-0 Input EXT Interface-Single Braceket 980-000Y-01-0 Input EXT Interface-Dual Braceket 980-000Z-01-0 Output EXT Interface-Dual Braceket

6.1 Specification Single DVI Input Module Interface Appearance Board Size 40x20mm Number of Connectors 1 Connector DVI-I (Compatible with DVI,CVBS,YPbPr, VGA) Supported Standards Single Link DVI Supported Resolution SMPTE 480i | 576i | 720p@50/59.94/60 | 1080i@50/59.94/60 | 1080p@50/59.94/60 VESA 800×600@60 |1024×768@60 |1280×768@60 I 1280×1024@60 | 1600×1200@60 | 1920×1080@60 | 1920×1200@60 | 2048×1152@60 Single USB Input/Backup Module Interface Appearance Board Size 40×38mm Number of Connectors 2 (1 In/1 Backup) Connector USB-A Supported Standard USB 2.0 Midia Types Video Formats MPEG1| MPEG2 | MPEG4 | H264 | RM | RMVB| MOV | MJPEG | VC1 | DIVX | FLV Image Formats JPEG | BMP | PNG Audio Formats WMA | MP3 |M4A|AAC Video Formats File Type File Extension Encoding Max Resolution Max Bitrate MPEG1 .DAT | .MPG | .MPEG 1920x1080 @30 20Mbps MPEG2 .MPG 1920x1080 @30 20Mbps MPEG4 .AVI | .MP4 | .3GP | .ASF DVIX | XVID 1920×1080 @30 20Mbps RM | RMVB .RM | .RMVB RV8 | RV9 | RV10 1280×720@ 30 10Mbps

MPEG | DVIX | H264 1920×1080 @30 20Mbps VC1 .WMV | .ASF VC1 1920×1080 @30 20Mbps FLV .FLV H264 1920×1080 @30 20Mbps Picture Formats File Type Max Resolution Compression Supported Resolution JPEG 15360×8640 Progressive JPEG Support 1024×768 only Baseline （“Standard”） Full Range Baseline Optimized Full Range BMP 9600×6400 Monochrome Full Range 16-color Full Range 256-color Full Range 16 bit Full Range 24 bit Full Range 32 bit Full Range PNG 9600×6400 Non-interlaced Full Range Single 2K HDMI Input Module Interface Appearance Board Size 40x20mm Number of Connectors 1 Connector HDMI-A Supported Resolution SMPTE 480i | 576i | 720p@50/59.94/60 | 1080i@50/59.94/60 | 1080p@50/59.94/60 VESA 800×600@60 | 1024×768@60 | 1280×720@50/59.94/60 | 1280×800@60 | 1280×960@60 | 1280×1024@60 | 1400×1050@60 | 1600×1200@60 | 1920×[email protected]/24/25/29.97/30/50/59.94/60 Supported Standard HDMI 1.3 3G-SDI Input /Loop Module

2 (1 Input, 1 Loop) Connector BNC Supported Resolution SMPTE 480i | 576i | 720p@50/60 | [email protected]/60 | [email protected]/24/25/29.97/30/59/59.94/60 | [email protected]/24/25/29.97/30 Supported Standard SMPTE 425M (Level A & B) | SMPTE 424M | SMPTE 292M | SMPTE 259M-C | DVB-ASI HDBaseT Input Module Interface Appearance Board Size 40(L)×38(W)（mm） Number of Connectors 1 Connector RJ45 Supported Resolution SMPTE 720p@50/59.94/60 | [email protected]/24/25/29.97/30/50/59.94/60 VESA 800×600@60/75/85 | 1024×768@60/75/85 | 1280×768@60 | 1280×800@60 |1280×1024@60/75/85 | 1360×768@60 | 1366×768@60 |1400×900@60 | 1600×1050@60 | 1600×1200@60 |1680×1050@60 | 1920×1080@60 | 1920×1200@60 | 2048×1152@60 | 2560×812@60 | 2560×816@60 Standard HDBaseT 1.0

Interface Appearance Board Size 40(L)×38(W)（mm） Number of Connectors 1 Connector Standard DVI-I Socket Supported Resolution SMPTE 720p@50/59.94/60| 1080p@50/59.94/60 VESA 800x600@60 |1024x768@60/75/85 |1280x720@50/59.94/60 |1280x800@60 |1280x960@60 | 1280x1024@60/75/85 | 1400x1050@60 |1600x1200@60 |[email protected]/24/25/29.97/30/50/59.94/60 |2048x1152@60 3G SDI Output Module Interface Appearance Board Size 40(L)×38(W)（mm） Number of Connectors 2 (Single Chanel dual port) Connector BNC interface Supported Standard SMPTE 425M (Level A & B) | SMPTE 424M | SMPTE 292M | SMPTE 259M-C | DVB-ASI Supported Resolution SMPTE 720p/50/59.94/60 | 1080i/50/59.94/60 |1080p/50/59.94/60 2K HDMI Output Module Interface Appearance Board Size 40(L)×38(W)（mm） Number of Connectors 1 Connector HDMI-A Supported Resolution SMPTE 720p50/59.94/60 | 1080i50/59.94/60 | 1080P50/59.94/60 VESA 800×600@60 | 1024×768@60 | 1280×768@60 | 1280×1024@60 | 1600×1200@60 | 1920×1080@50/60 Format Standard HDMI 1.3

Interface Apperance Board Size 40(L)×38(W)（mm） Number of Connectors 1 Connector DisplayPort Supported Resolution SMPTE 720p50/59.94/60 | 1080i50/59.94/60 | 1080P50/59.94/60 VESA 800×600@60 | 1024×768@60 | 1280×768@60 | 1280×1024@60 | 1600×1200@60 | 1920×1080@50/60 Format Standard DP 1.1 HDBaseT Output Module Interface Appearance Number of Connectors 1 Connector RJ45 Supported Resolution SMPTE 720p@50/59.94/60 | 1080i@50/59.94/60 | [email protected]/24/25/29.97/30/50/59.94/60 VESA 800×600@60/75/85 | 1024×768@60/75/85 | 1280x768@60 | 1280×800@60 |1280×1024@60/75/85 | 1360×768@60 | 1366×768@60 |1400×900@60 | 1600×1050@60 | 1600×1200@60 |1680×1050@60 | 1920×1080@60 | 1920×1200@60 | 2048×1152@60 | 2560×812@60 | 2560×816@60 Supported Standards HDBaseT 1.0 Subito Quatro Sender Interface Appearance Number of Connectors 4×RJ45 Supported Resolution VESA 1024×768@60 | 1280×1024@60 | 1440×900@60 | 1600×900@60 | 1600×1050@60 | 1920×1080@60 |

Capacity 655,360 pixels ( each port) Horizontal Range 3840 pixels( each port) Vertical Range 2048 pixels( each port) Communication Interface Appearance Genlock Number of Connectors 2 Connector BNC (1 In | 1 Loop) Control Number of Connectors 2 Connector 1×RJ11 |1× RJ45 PVW Interface Appearance Number of Connectors 2 (1 HDMI | 1 H.264) Connector 1×HDMI-A |1× RJ45 Extras Power Supply 100-240V IEC-3 Working Environment 0°C~45°C Stored Environment 10% to 90% Product Warranty 3 years parts and labor warranty

The following terms and definitions are used throughout this guide.  “ASCII”: American Standard for Information Interchange. The standard code consisting of 7-bit coded characters (8 bits including parity check) used to exchange information between data processing systems, data communication systems, and associated equipment. The ASCII set contains control characters and graphic characters.  “Aspect ratio”: The relationship of the horizontal dimension to the vertical dimension of an image. In viewing screens, standard TV is 4:3, or 1.33:1; HDTV is 16:9, or 1.78:1. Sometimes the “:1” is implicit, making TV = 1.33 and HDTV = 1.78.  “AV”: Audio visual, or audio video.  A “Background” is an unscaled source, typically originating from a computer. A background source appears at the system’s lowest priority — visually in back of all other sources.  “Baudrate”: Named of J.M.E. Baudot, the inventor of the Baudot telegraph code. The number of the electrical oscillations per second, called baud rate. Related to, but not the same as, transfer rate in bits per second (bps).  “Blackburst”: The video waveform without the video elements. It includes the vertical sync, horizontal sync, and the chroma burst information. Blackburst is used to synchronize video equipment to align the video output. One signal is normally used to set up an entire video system or facility. Sometimes it is called House sync.  “BNC”: Bayonet Neill-Concelman. A cable connector used extensively in television and named for its inventors. A cylindrical bayonet connector that operates with a twist-locking motion. To make the connection, align the two curved grooves in the collar of the male connector with the two projections on the outside of the female collar, push, and twist. This allows the connector to lock into place without tools.  “Brightness”: Usually refers to the amount or intensity of video light produced on a screen without regard to color. Sometimes called “black level.  “CAT 5”: Category 5. Describes the network cabling standard that consists of four unshielded twisted pairs of copper wire terminated by RJ-45 connectors. CAT 5 cabling supports data rates up to 100 Mbps. CAT 5 is based on the EIA/TIA 568 Commercial Building Telecommunications Wiring Standard.  “Color bars”: A standard test pattern of several basic colors (white, yellow, cyan, green, magenta, red, blue, and black) as a reference for system alignment and testing. In NTSC video, the most commonly used color bars are the SMPTE standard color bars. In PAL video, the most commonly used color bars are eight full field bars. In the computer, the most commonly used color bars are two rows of reversed color bars.  “Color burst”: In color TV systems, a burst of subcarrier frequency located on the back porch of the composite video signal. This serves as a color synchronizing signal to establish a frequency and phase reference for the chroma signal. Color burst is 3.58 MHz for NTSC and 4.43 MHz for PAL.

source. The higher the color temperature, the bluer the light. The lower the temperature, the redder the light. Benchmark color temperature for the A/V industry include 5000°K, 6500°K, and 9000°K.  “Contrast ratio”: The radio of the high light output level divided by the low light output level. In theory, the contrast radio of the television system should be at least 100:1, if not 300:1. In reality, there are several limitations. In the CRT, light from adjacent elements contaminate the area of each element. Room ambient light will contaminate the light emitted from the CRT. Well-controlled viewing conditions should yield a practical contrast ratio of 30:1 to 50:1.  “DVI”: Digital Visual Interface. The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins that handles both digital and analog video.  “EDID”: Extended Display Identification Data – EDID is a data structure used to communicate video display information, including native resolution and vertical interval refresh rate requirements, to a source device. The source device will then output the optimal video format for the display based on the provided EDID data, ensuring proper video image quality. This communication takes place over the DDC – Display Data Channel.  “Ethernet”: A Local Area Network (LAN) standard officially known as IEEE 802.3. Ethernet and other LAN technologies are used for interconnecting computers, printers, workstations, terminals, servers, etc. within the same building or campus. Ethernet operates over twisted pair and over coaxial cable at speeds starting at 10Mbps. For LAN interconnectivity, Ethernet is physical link and data link protocol reflecting the two lowest layers of the OSI Reference Model.  “Frame”: In interlaced video, a frame is one complete picture. A video frame is made up of two fields, or two sets of interlaced lines. In a film, a frame is one still picture of a series that makes up a motion picture.  “Gamma”: The light output of a CRT is not linear with respect to the voltage input. The difference between what you should have and what is actually output is known as gamma.  “HDMI” - High – Definition Multimedia Interface: An interface used primarily in consumer electronics for the transmission of uncompressed high definition video, up to 8 channels of audio, and control signals, over a single cable. HDMI is the de facto standard for HDTV displays, Blu-ray Disc players, and other HDTV electronics. Introduced in 2003, the HDMI specification has gone through several revisions.  “HDSDI”: The high-definition version of SDI specified in SMPTE-292M. This signal standard transmits audio and video with 10 bit depth and 4:2:2 color quantization over a single coaxial cable with a data rate of 1.485 Gbit/second. Multiple video resolutions exists including progressive 1280x720 and interlaced 1920x1080 resolution. Up to 32 audio signals are carried in the ancillary data.  “JPEG” (Joint photographic Expects Group): Commonly used method of lossy compression for photographic images using a discreet cosine transfer function. The

storage size and image quality. JPEG typically achieves 10:1 compression with little perceptible loss in image quality. Produces blocking artifacts.  “MPEG”: Motion Picture Expect Group. A standard committee under the auspices of the International Standards Organization working on algorithm standards that allow digital compression, storage and transmission of moving image information such as motion video, CD-quality audio, and control data at CD-ROM bandwidth. The MPEG algorithm provides inter-frame compression of video images and can have an effective compression rate of 100:1 to 200:1.  “NTSC”: The color video standard used in North America and some other parts of the world created by the National Television Standards Committee in the 1950s. A color signal must be compatible with black-and-white TV sets. NTSC utilizes an interlaced video signals, 525 lines of resolution with a refresh rate of 60 fields per second (60 Hz). Each frame is comprised of two fields of 262.5 lines each, running at an effective rate of 30 frames per second.  “Operator”: Refers to the person who uses the system.  “PAL”: Phase Alternate Line. A television standard in which the phase of the color carrier is alternated from line to line. It takes four full pictures (8 fields) for the color-to-horizontal phase relationship to return to the reference point. This alternation helps cancel out phase errors. For this reason, the hue control is not needed on a PAL TV set. PAL, in many transmission forms, is widely used in Western Europe, Australia, Africa, the Middle East, and Micronesia. PAL uses 625-line, 50-filed (25 fps) composite color transmission system.  “PIP”: Picture-in-Picture. A small picture within a larger picture created by scaling down one of the images to make it smaller. Each picture requires a separate video source such as a camera, VCR, or computer. Other forms of PIP displays include Picture-by-Picture (PBP) and Picture-with-Picture (PWP), which are commonly used with 16:9 aspect display devices. PBP and PWP image formats require a separate scaler for each video window.  “Polarity”: The positive and negative orientation of a signal. Polarity usually refers to the direction or a level with respect to a reference (e.g. positive sync polarity means that sync occurs when the signal is going in the positive direction).  “RJ-45”: Registered Jack-45. A connector similar to a telephone connector that holds up to eight wires, used for connecting Ethernet devices.  “RS-232”: An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either DB-9 or DB-25 connectors. This standard is used for relatively short-range communication and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length, and type of connector to be used. The standard specifies component connection standards with regard to the computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard.  “Saturation”: Chroma, chroma gain. The intensity of the color, or the extent to which

color or the greater its saturation. On a display device, the color control adjusts the saturation. Not to be confused with the brightness, saturation is the amount of pigment in a color, and not the intensity. Low saturation is like adding white to the color. For example, a low-saturated red looks pink.  “Scaling”: A conversion of a video or computer graphic signal from a starting resolution to a new resolution. Scaling from one resolution to another is typically done to optimize the signal for input to an image processor, transmission path or to improve its quality when presented on a particular display.  “SDI”: Serial Digital Interface. The standard based on a 270 Mbps transfer rate. This is a 10-bit, scrambled, polarity independent interface with common scrambling for both component ITU-R 601 and composite digital video and four channels of (embedded) digital audio.  “Seamless Switching”: A feature found on many video switchers. This feature causes the switcher to wait until the vertical interval to switch. This avoid a glitch (temporary scrambling) which normally is seen when switching between sources.  “SMPTE”: Society of Motion Picture and Television Engineers. A global organization, based in the United States, that sets standards for baseband visual communications. This includes film as well as video and television standards.  “S-Video”: A composite video signal separated into the luma (“Y” is for luma, or black and white information; brightness) and the chroma (“C” is an abbreviation for chroma, or color information).  “Sync”: Synchronization. In video, sync is a means of controlling the timing of an event with respect to other events. This is accomplished with timing pulses to insure that each step in a process occurs at the correct time. For example, horizontal sync determines exactly when to begin each horizontal scan line. Vertical sync determines when the image is to be refreshed to start a new field or frame. There are many other types of sync in video system.(Also known as “sync signal” or “sync pulse.”)  “TCP/IP”: Transmission Control Protocol/Internet Protocol. The communication protocol of the Internet. Computers and devices with direct access to the Internet are provided with a copy of the TCP/IP program to allow them to send and receive information in an understandable form.  “USB”: Universal Serial Bus. USB was developed by seven PC and telecom industry leaders (Compaq, DEC, IBM, Intel, Microsoft, NEC, and Northern Telecom). The goal was easy plug-and-play expansion outside the box, requiring no additional circuit cards. Up to 127 external computer devices may be added through a USB hub, which may be conveniently located in a keyboard or monitor. USB devices can be attached or detached without removing computer power. The number of devices being designed for USB continues to grow, from keyboards, mice, and printers to scanners, digital cameras, and ZIP drives.  “VESA”: Video Electronics Standards Association. A nonprofit number organization dedicated to facilitating and promoting personal computer graphics through improved standards for the benefit of the end-user. www.vesa.org

with TTL level separate horizontal and vertical sync. The video outputs to a 15-pin HD connector and has a horizontal scan frequency of 31.5 kHz and vertical frequency of 70 Hz (Mode 1, 2) and 60 Hz (Mode 3). The signal is non-interlaced in modes 1, 2, and 3 and interlaced when using the 8514/A card (35.5 kHz, 86 Hz) in mode 4. It has a pixel by line resolution of 640×480 with a color palette of 16 bits and 256,000 colors.  “YCrCb”: Used to describe the color space for interlaced component video.  “YPbPr”: Used to describe the color space for progressive-scan (non-interlaced) component

The table below lists the changes to the Video Processor User Manual. Format Time ECO# Description Principal V1.0 2019-09-01 0000# Release Fanny