Outback ProHarvest 208V Quick Start Manual

 Powered up  Generating, no faults  Faulted; for example, arc fault detected  “Off and Locked”; unit is disabled  Sleeping  Not generating 900-0202-01-00 REV B ©2016 OutBack Power Technologies. All Rights Reserved. IMPORTANT: Not intended for use with life support equipment. Buttons and Indicators ProHarvest 208V Quick Start Guide Date and Revision January 2017, Revision B This guide provides instructions for installation and setup of the product. It assumes knowledge of features, functions, and general operation. This guide is a supplement for the purpose of expediting installation. For complete information, see the ProHarvest Installation and Safety Manual. These instructions are for use by qualified personnel who meet all local and governmental code requirements for licensing and training for the installation of 3-phase electrical power systems with AC and DC voltage up to 1000 volts. ! CAUTION: EQUIPMENT DAMAGE  This system is to be connected to 208 Vac 3-phase wye input ONLY (three phases, neutral, ground).  This product has no user-serviceable parts. Tampering with the product will void the warranty.  Applying incorrect polarity to DC string inputs will result in damage. This will void the warranty.  The Communications Gateway is for indoor use only.  All conductors (L1, L2, L3, neutral, ground) must be connected. Neutral must be bonded to earth ground. Failure to do so can damage the inverter and void the warranty. B C A AC Cable (ordered separately)  CBL-208A-05 (5')  CBL-208A-15 (15')  CBL-208A-30 (30')  CBL-208A-50 (50') Button State Meaning Initial state. Once pressed, a dark blue color indicates the Gateway is in the process of discovering inverters. It will return to the initial state with an empty serial number list if no inverters are found. A dark red color indicates an error was found. Examples: “signal strength is too low”; “too much background noise on circuit”. The red color only clears when the user re-tries and the fault condition no longer applies. Once discovery has successfully occurred, this button returns to the initial state. Button Push 1 press 2 presses 3 presses Long press (> 2 secs) 1 press (after long press) 3 presses (after long press) 4 presses (after long press) Result  Make inverter beep; i.e. “Are you alive?”  “Off & Locked”. Unit is disabled.  Unit will not begin the 5-minute self-start.  Start generating immediately  If locked, unlock and generate immediately  If system is faulted, unit will unlock but will not generate  “Alternate functions” mode: Ready to accept further button pushes. This times out after 10 seconds.  Clear latched faults; for example, after residual-current device (RCD) test or arc-fault test has initiated a fault condition.  RCD-test activation. Successful activation of RCD test should cause a fault condition (rapid red flashing) until cleared.  Arc-fault test activation. Successful activation of arc-fault detection should cause a fault condition (rapid red flashing) until cleared. Button and LED Indicator Includes AC Connector Tool, DC Connector Tool TOOL-KIT-1 (ordered separately) ProHarvest 208V Inverter  PRO208-5k75  PRO208-5k75-AUX Communications Gateway (ordered separately)  PROGW-A-120 Includes SD card, Ethernet cable, 120 Vac cable AC Splice (optional component)  PROSPL-60

©2016 OutBack Power Technologies. All Rights Reserved. Installation E F Neutral L1, L2, L3 Ground Grid: Three-phase 208 Vac wye only (neutral, ground, and three phases) OCPD Dedicated branch circuit 60A max overcurrent protective device (OCPD) Additional dedicated branch circuits 15A OCPD Neutral, ground, and one phase OCPD Gateway Neutral, ground, and three phases Equipment ground supplied through AC connector Connector is means of DC disconnect (see H) ~ ~ = = ProHarvest 208V ProHarvest 208V Equipment ground PV String 1 PV String 2 Connector is means of AC disconnect (see D) OCPD ProHarvest 208V AC Splice box Inverter AC cable (5-foot to 50-foot lengths available) 5 I H ! CAUTION: EQUIPMENT DAMAGE Do not reverse the DC “+” and “–“ input polarities. This will damage the inverter and void the warranty. 1 G 1 2 3 4 6 5 7 2 8 9 10 ~ =