SAMCHULLY QJC Instruction Manual

척 사용 중 이상발생시 아래와 같은 점을 재확인하시고 당사에 연락을 주시면 친절히 설명하여 드리겠습니다. If the chuck malfunctions, stop the lather and try the following countermeasures. 문제점 Nonconformity 원인 Cause 대책 Action 척이 작동하지 않는다. Chuck will not operate 척 부품이 파손되어 있다. The inside of the chuck is broken. 분해 후 교환한다. Disassemble and replace part. 습동부가 늘어붙어 있다. Slide way seizes. 분해 후 늘어붙은 부위를 제거 수정 � ...

3-4. 기능 및 취급 Thrn rod of hexagon socket which supports each jaw and be available for moving handle exists. When you try to change base jaws, should change the base jaws in unclamping status. (1) Turning turn rod to counterclockwise (to the un- lock③ (see Fig.9)) by T-handle activates the CAM bolt which causes the serrations on the wedge bar to disengage from the base jaws. (2) The position of the base jaws can be easily ad- justed by moving to inner or outer. (3) To remove T-handle, turning handle to clockwise should be adjusted with the groove ...

Quick Jaw Change Chuck IDF Instruction Manual www.samchully.com Korea Production monitored Type tested Produktion uberwacht Bauart gepruft “ s ISO 9001:2008 Samchully Machinery [405-820] 인천광역시 남동구 남동대로 99 TEL. +82-32-822-4811 FAX. +82-32-822-4377 [405-820] 99, Namdong-daero, Namdong-gu, Incheon, Korea TEL. +82-32-899-8965 FAX. +82-32-721-7607 40 Power Chuck ...

K1 K2 ι2(3x120˚) ι1(3x120˚) T1 U V N P Q F L2 B E J C A L1 H G W T2 ι2(3x120˚) ι1(3x120˚) T1 U T2 QJC-206 QJC-208 QJC-210 QJC-212 QJC-215 QJC-220 죠스트로크 직경 [mm] Jaw Stroke Dia. 11.4 14.4 16 16 17 20 플런져 스트로크 [mm] Plunger Stroke 20 25 28 28 32 42 허용최대입력 [kN(kgf)] Pemissible Input Force 30(3059) 54(5404) 65(6628) 90(9177) 133(13562) 120(12236) 최대정적 파악력 [kN(kgf)] Max.static Gripping Force 45(4538) 100(10197) 115(11726) 160(16315) 240(24473) 250(25492) 허용최고 회전속도 [min -1] Max. R.p.m. 6000 55 ...

9. 부품도 2 29 3 26 11 4 10 1 5 21 24 22 12 15 16 13-E 6 8 19 13-C 7 13-B 17 13-D 18 13-A 24 14 20 9 28 27-B 27-A 25 34 Power Chuck ...

For the cylinder, refer to the instruction manual. ! CAUTION 주 의 ! CAUTION ! WARNING 경 고 ! WARNING 경 고 ! WARNING ! WARNING If the drawpipe is insufficiently screwed into the draw- nut, the thread will be damaged, thus eliminating the gripping force momentarily. It will result danger due to discharge of workpiece. (4) Mount the chuck to the spindle (back plate) Turn the joint handles so that the chuck is prorerly attached to the spindle mounting face of lathe. Uniformly tighten chuck mounting b ...

부에 플러그를 파악합니다. 이때 플러그가 경사가나지 않도록 척 단면에 플러그를 밀착시켜 파악 해 주십시오. Grip the plug at the Ø D- forned part by operating the valve. At this time grip with it pressed against the front face of chuck lest the plug should decline. Ø d 플러그를 파악한 상태에서 공작 물 파악부(Ød＇)를 성형합니 다. Ød＇부는 공작물의 파악 부 직경과 같은 크기(H7 정도)에 서 표면조도는 6S 이하로 가공 해 주십시오. 성형시의 압력은 ...

3-4. 기능 및 취급 Thrn rod of hexagon socket which supports each jaw and be available for moving handle exists. When you try to change base jaws, should change the base jaws in unclamping status. (1) Turning turn rod to counterclockwise (to the un- lock③ (see Fig.9)) by T-handle activates the CAM bolt which causes the serrations on the wedge bar to disengage from the base jaws. (2) The position of the base jaws can be easily ad- justed by moving to inner or outer. (3) To remove T-handle, turning handle to clockwise should be adjusted with the groove ...