Genelec 1032A Installation Manual

for 1032A, S30C, 1037B/C, HT210, HT210B and HT312A Installation Manual Kit Contents The following hardware is included with this rack adapter kit: One 7U Rack mount chassis unit with cable and connectors in place, one Speaker cable adapter and four 4 x 2 mm screws. The bolts and nuts for attaching the rack adapter into an equipment rack are not included in this kit. Cables to go between the amplifier and speaker are not included in this kit. To complete the installation, one of the fol­ lowing cable kits is needed: Order code Length 1039-203 2 meters 1039-204 5 meters 1039-205 10 meters 1039-206 15 meters 1039-207 20 meters If you choose to build the cables yourself, note that the maximum speaker cable length is 20 meters and the conductor wire used should be at least 2.5mm² (13 AWG) Note that the cabling in this rack mount kit does not support the Mode indicator LED function on the Genelec S30D Digital Monitoring System. Assembly Place the speaker face down on a flat sur­ face. Remove the amplifier from the rear of the speaker cabinet by loosening the six M4 screws at the edge of the longer sides.Take special care not to stress the speaker cable that connects the amplifier and speaker cabinet. Disconnect the speaker cable from the amplifier. Connect the speaker cable to the speaker cable adapter’s connector (see fig. 1 overleaf). Attach the speaker cable adapter to the speaker box with four 4 x 12 mm screws. If your speaker is Genelec type S30C, you may notice that the speaker cable wire colour pattern is not the same as on the adapter’s connector. This is normal, the wire sequence is correct despite the difference in colour coding. Place the amplifier and the rack adapter side by side on a flat surface and connect the rack adapter cable (see fig 2 overleaf) to the amplifier board. Place the amplifier on the rack adapter chassis and fix it with six M4 screws. Ensure that the rack adapter cable does not tighten or press against any amplifier components. The rack adapter can now be mounted into a standard 19 inch rack. Leave at least ten centimeters (4 inches) free space above and below the amplifier to ensure cooling. Connect the amplifier to the speaker with two Speakon 8- and 4-pole cables (Genelec part no 1039-204 or 1039-205) and place the speaker in its recess. Now the system is ready for operation. 1037B/C, S30C AND 1032A SPEAKER CONNECTOR PIN NUMBER SIGNALS 1 + T+ T- T+ 1 - T- T+ T- 2 + M+ M+ N/C 2 - M- M- N/C 3 + B+ B+ B+ 3 - B- B- B- 4 + N/C N/C N/C 4 - N/C N/C N/C 1037B/C, S30C AND 1032A LED CONNECTOR PIN NUMBER SIGNALS 1 + CLIP LED + 1 - CLIP LED - 2 + POWER LED + 2 - POWER LED - HT210 AND HT210B SPEAKER CONNECTOR PIN NUMBER SIGNALS 1 + T+ 1 - T- 2 + CLIP LED 2 - N/C 3 + B+ 3 - B- 4 + N/C 4 - N/C HT210 AND HT210B LED CONNECTOR PIN NUMBER SIGNALS 1 + N/C 1 - N/C 2 + POWER LED + 2 - POWER LED - HT312A SPEAKER CONNECTOR PIN NUMBER SIGNALS 1 + T+ 1 - T- 2 + M+ 2 - M- 3 + B+ 3 - B- 4 + N/C 4 - N/C HT312A LED CONNECTOR PIN NUMBER SIGNALS 1 + POWER LED 1 - LED GND 2 + N/C 2 - CLIP LED Connector wiring

International enquiries: Genelec, Olvitie 5 FIN-74100, Iisalmi, Finland Phone +358 17 83881 Fax +358 17 812 267 Email [email protected] In the U.S. please contact: Genelec, Inc., 7 Tech Circle Natick, MA 01760, U.S.A. Phone +1 508 652 0900 Fax +1 508 652 0909 Email [email protected] www.genelec.com Option 11 (1037-412)Rack Adapter for 1032A, S30C, 1037B/C, HT210, HT210B and HT312A Installation Manual Dimensions W H D Rack mount chassis (mm) 483 310 82* (inches) 19 121/4 31/2* Speaker cable adapter (mm) 118 67 57 (inches) 45/8 25/8 21/4 * Without Speakon connecting cable. Cable connectors require additional 100 mm (4 inches) of space behind the amplifier Fig. 1. Installing the speaker cable adapter 1 Speaker cable connector 2 Speaker cable adapter 3 4 x 12 mm screw 4 Speakon 8- and 4-pole cables (not included in the kit) Fig. 2. Mounting the amplifier into the rack adapter chassis 1 M4 screw 2 Amplifier unit 3 Rack adapter cable connector 4 Rack adapter chassis 5 Speakon 8- and 4-pole cables (not included in the kit) 1 2 3 4 5 In Sweden please contact Genelec Sverige Ellipsvägen 10B P.O. Box 5521, S-141 05 Huddinge Phone +46 8 449 5220 Fax +46 8 708 7071 Email [email protected] In China please contact: Beijing Genelec Audio Co. Ltd. Jianwai SOHO, Tower 12, Room 2306 39 East 3rd Ring Road Chaoyang District Beijing 100022, China Phone +86 0 5869 7915, Fax +86 10 5869 7914