Oriental motor BMU Series Quick Start Manual

BMU Series HM-5191-3 CN1 : 3 pin CN4 : 9 pin □ Connector □ Motor □ Driver □ Mounting screw set Package contents Motor (sold separately) The fgure shows an example of the combination type. ∗ Be sure to match the motor output power with the driver output power. Supplied with the combination type. □ OPERATING MANUAL □ OPERATING MANUAL To connect the motor and driver, the dedicated connection cable is always needed. Connection cable (sold separately) □ QUICK START GUIDE (this document) CN1 : 3 pin CN4 : 12 pin • 30 W to 120 W • 200 W to 400 W This document describes for when the motor is of the connector type. The descriptions other than "connection for motor and cable" are common to the BMU Series. 2 Operating a motor The figure shows the 30 W to 120 W driver. Thank you for purchasing an Oriental Motor product. Use the product correctly after thoroughly reading the section "Safety precautions" of the operating manual. This document describes methods till rotating the motor after connecting it to the driver. For details about how to use the product, refer to the supplied with the driver. OPERATING MANUAL The package includes the items shown below. FWD REV 1 2 3 FWD REV The fgure is an example for when the product is of a single-phase 100 VAC. P U S H - S E T FWD REV Rotation speed 0 r/min (standstill) [ Example: 50 → 1000 r/min ] The motor rotates. 50 r/min (factory setting) Setting dial Operation switch Set the operation switch to Rotation direction switch Switch the motor rotation direction using the rotation direction switch. [ STAND-BY ] [ RUN ] FWD REV The motor stops. To stop the motor Start of motor Change of motor speed AC power ON Power ON The display blinks If the power supply is turned on while the operation switch is set to the [RUN] side, the alarm is generated. 【 How to reset 】Set the operation switch to [STAND-BY]. The alarm is reset, and the motor rotation speed is displayed. [ STAND-BY ] Adjustment Decelerate Accelerate When the setting dial is pressed, the display changes to lighting from blinking, and the speed will be set. When you start the motor next time, it will rotate at the set speed. Press When the setting dial is turned, the display blinks. You can change the speed while blinking. Set © Copyright ORIENTAL MOTOR CO., LTD. 2015 ORIENTALMOTOR CO.,LTD. Published in December 2019

Connect a power supply cable according to the power-supply voltage specifcations of the driver. Prepare the power supply cable since it is not supplied with the product. Connection cable CN3 CN1 CN1 CN1 CN1 This is an example for when the cable is "leading in direction of output shaft." CN1 CN1 CN1 Ground Insert the lead wire to the connector so that the tip part (copper wires after stripping the insulation cover) does not become loose. The loose tip part (copper wires) may cause short-circuiting, leading to damage to the product. Note Connection for motor and cable 1 Remove CN2 Grounding Be sure to ground using the Protective Earth Terminal . Be sure to ground the product. Failure to do so may result in electric shock or damage to the product. Static electricity may cause damage to the product if the Protective Earth Terminals are not grounded. Note Protective Earth Terminal M4 Protective Earth Terminal M4 Connector cap The 400 W type is indicated L1, L2, and L3 only. The connector cannot be inserted if the locking lever is turned down. Insert into CN1 2 Attach Be sure to turn down the locking lever till the position shown in the fgure. 3 Secure 10 mm Insert the lead wire while pushing the button of the orange color with a screwdriver. Lead wire Button of the orange color Screwdriver AWG18～14 （0.75～2.0 mm2） Locking lever Cable outlet in output shaft direction Cable outlet in opposite to output shaft direction Cable outlet in vertical direction Model: CC_____F Model: CC_____B Model: CC_____V Prepare a grounding wire since it is not supplied with the product. AWG18～14（0.75～2.0 mm2) 30 W to 120 W 200 W to 400 W