EAW MQV1366e Specifications

508 234 6158 Toll Free 800 992 5013 FAX 508 234 8251 [email protected] www.eaw.com EAW products are continually improved. All specifications are therefore subject to change without notice. MQV1366e/0002690/002/2 pp October 2003 Printed in USA FEATURES DESCRIPTION PERFORMANCE APPLICATION • Full-range, 3-way system • 15-in LF; 10-in horn-loaded MF; 2-in exit Neodymium HF • 60° x 60° beamwidth • Horizontally configured to create vertical arrays A 3-way, full-range system in a vented trapezoidal enclosure. Includes a slot-loaded 15-in woofer, a horn-loaded 10-in MF cone with Radial Phase Plug™, and a 2-in exit/3-in diaphragm Neodymium compression driver. The MF and HF horns provide a nominal 60° x 60° beamwidth. An internal passive crossover with jumpers on the input panel allows user selection of either bi-amplified or passive operation. In either case digi- tal signal processing is required to achieve specified perform- ance. The enclosure features a comprehensive system of 3/8”- 16 threaded suspension points. The MQV1366e combines the MQ Series LF/MF/HF components into a full-range, single-enclosure loudspeaker. It is horizon- tally configured for arraying in vertical columns. This arrange- ment is typically used in sports arenas and other venues where the array must address wide, vertical audience angles. The MF/HF horns in the MQV1366e feature a rigid but well-damped construction using wood veneer backed by structural foam. A no-compromise design means the mid and high frequency horns are truly large enough to provide optimal pattern con- trol throughout each passband. Application Usage: Install Houses of Worship Auditoriums Theatres Arenas Performing Arts Centers Stadiums Calculated Maximum Output (dB SPL @ 1m) LF Peak/Long Term 128/122 MF/HF Peak/Long Term 140/134 MF Peak/Long Term 141/135 HF Peak/Long Term 134/128 Nominal Coverage Angle, -6 dB Points (degrees) Horizontal 60 Vertical 60 Recommended High-Pass Frequency 24 dB/Octave 50 Hz Frequency Response ±3 dB 70 Hz to 15 kHz -10 dB 50 Hz Axial Sensitivity (dB SPL, 1 Watt @ 1m) LF 95 MF/HF 108 MF 109 HF 106 Impedance (Ohms) LF 8 MF/HF 8 MF 8 HF 8 Power Handling, AES Standard (Watts) LF 550 MF/HF 400 MF 400 HF 150 LF Subsystem 1x 15-in woofer MF Subsystem 1x 10-in horn loaded cone HF Subsystem 2-in exit/3-in diaphragm com- pression driver on constant directivity horn Configuration Three-way, full range Powering Bi- or Tri-amplified Enclosure Materials Exterior grade Baltic birch plywood Finish Wear-resistant textured black paint Connectors Terminal barrier strip Suspension Hardware 16x 3/8”-16 threaded mounting points (4 each on top, bottom and sides Grille Powder coated perforated steel Dimensions inches millimeters Height (front) 26.65 677 Height (rear) 15.3 389 Width 56.25 1429 Depth 25.59 650 Trapezoid Angle 12.5 Degrees per Side Weights pounds kilograms Net Weight 215 97.7 Shipping Weight 240 109.1

One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX 508 234 8251 [email protected] www.eaw.com EAW products are continually improved. All specifications are therefore subject to change without notice. MQV1366e/0002690/002/2 pp October 2003 Printed in USA Manufacturing tolerances are +/-0.13 and +/-1° A 15.34 25.59 BACK INPUT L C L RIGHT SIDE LC C 8.09 15.71 A VIEW A-A GRILLE PARTIALLY SHOWN FRONT NOTES: 1. SYMBOL INDICATES MOUNTING POINT, 3/8-16 THREADED HOLE (PI ANGLE). 2. SYMBOL INDICATES CENTER OF BALANCE. 3. WEIGHT APPROX. 215 LBS. 4. SHIPPING WEIGHT APPROX. 240 LBS. 56.25 52.35 DIMENSIONS APPLY TO TOP AND BOTTOM 0002330(A) 9/3/02 26.65 4.00 13.30 27.50 5.00 (15.30) 12.75 25° DIMENSIONS APPLY TO BOTH SIDES 7.50 (1.95) 12.50 19.55 2X ACCESS PANEL The 3-way full-range loudspeaker shall incorporate a 15-in slot-loaded woofer, a 10-in MF cone with Radial Phase Plug™, and a 2-in exit/3-in diaphragm HF compression driver. The MF and HF devices shall be loaded on horns that provide a nom- inal 60° x 60° beamwidth. An internal passive crossover net- work shall offer either bi- or tri-amplified operation, config- urable via jumpers on the input panel. System frequency response shall vary no more than 63 dB from 70 Hz to 15 kHz measured on axis. The LF section shall pro- duce a sound pressure level of 95 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of produc- ing a peak output of 128 dB SPL on axis at 1 meter. The LF section shall handle 550 watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 ohms. When operated in bi-amplified mode, the MF/HF section shall produce a sound pressure level of 108 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 140 dB SPL on axis at 1 meter. The MF/HF section shall handle 400 watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 ohms. When operated in tri-amplified mode, the MF section shall produce a sound pressure level of 109 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 141 dB SPL on axis at 1 meter. The MF section shall handle 400 watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 ohms. The HF section shall produce a sound pressure level of 106 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 134 dB SPL on axis at 1 meter. The HF section shall handle 150 watts of amplifier power (AES Standard) and shall have a nominal impedance of 8 ohms. The loudspeaker enclosure shall be trapezoidal in shape. It shall be constructed of exterior grade Baltic birch plywood and shall employ extensive internal bracing. It shall be fin- ished in wear-resistant textured black paint. Input connectors shall be a terminal strip. A total of 16x 3/8”-16 threaded mounting/suspension points (4 each top, bottom, and sides) shall be provided. The front of the loudspeaker shall be cov- ered with a powder coated perforated steel grille. The 3-way full-range loudspeaker shall be the EAW model MQV1366e.