Opticon F-100 SR Specification Manual

This manual provides specifications for the F-100 SR fixed position 1D scanner. 1st

Document History Model Number: F-100 SR Specification Number: SS17028 Edition: 1st Original Spec Number: (SS17027) Date: 21-February-2018 © 2018 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers Please read this manual carefully before installing or using the product. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase excluding batteries. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your product or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184 Support USA Europe Phone: 800-636-0090 Phone: +31235692728 Email: [email protected] Email: [email protected] Web: www.opticonusa.com Web: www.opticon.com

Edition Date Page Section Description of Changes First 2018/02/21 - -

1 Overview ....................................................................................................................... 1 2 Model details ................................................................................................................ 2 3 Standard ................................................................................................................................... 2 3.1 Model Description ..................................................................................................................... 2 3.2 Basic Specifications .................................................................................................... 3 4 Detailed View ................................................................................................................ 5 5 Detailed View ........................................................................................................................... 5 5.1 LED Indicator Specifications .................................................................................................... 6 5.2 Electrical Specifications .............................................................................................. 7 6 RS-232C Specification ............................................................................................................. 7 6.1 USB Specification ..................................................................................................................... 7 6.2 Optical Specifications .................................................................................................. 8 7 Basic Optical Specifications ..................................................................................................... 8 7.1 Focal Plane (F.P) ..................................................................................................................... 8 7.2 Optical Axis and Dead Zone ..................................................................................................... 8 7.3 Technical Specifications .............................................................................................. 9 8 Barcode Test Sample ............................................................................................................... 9 8.1 Scan Area ............................................................................................................................... 10 8.2 Depth of Field ......................................................................................................................... 10 8.3 Printed Contrast Signal (PCS)................................................................................................ 11 8.4 Minimum Resolution ............................................................................................................... 11 8.5 Barcode Width ........................................................................................................................ 11 8.6 Pitch, Skew and Tilt ................................................................................................................ 12 8.7 Curvature ................................................................................................................................ 12 8.8 Motion Tolerance .................................................................................................................... 13 8.9 Interface Specification ............................................................................................... 14 9 RS-232C Interface (D-Sub 9pin) ............................................................................................ 14 9.1 9.1.1 Communication Initial Setting ......................................................................................... 14 9.1.2 Signal Specification ........................................................................................................ 14 9.1.3 Pin Assignment ............................................................................................................... 14 9.1.4 RS-232C D-Sub 9pin Circuit ........................................................................................... 15 9.1.5 RS-232C D-Sub 9pin Interface Cable ............................................................................ 15 RS-232C Interface (Loose End) ............................................................................................. 16 9.2 9.2.1 Communication Initial Setting ......................................................................................... 16 9.2.2 Signal Specification ........................................................................................................ 16 9.2.3 Pin Assignment ............................................................................................................... 16 9.2.4 RS-232C Loose End Circuit............................................................................................ 17 9.2.5 RS-232C Loose End Interface Cable ............................................................................. 17 USB Interface ......................................................................................................................... 18 9.3

9.3.2 USB Connector ............................................................................................................... 18 9.3.3 USB Interface Circuit ...................................................................................................... 19 9.3.4 USB Interface Cable ....................................................................................................... 19 Environmental Specifications ................................................................................... 20 10 Temperature ........................................................................................................................... 20 10.1 Humidity .................................................................................................................................. 20 10.2 Ambient Light Immunity .......................................................................................................... 21 10.3 Dust and Drip Proof ................................................................................................................ 21 10.4 Scan Key Durability ................................................................................................................ 22 10.5 Cable Strength ....................................................................................................................... 22 10.6 Cable Bending Strength ......................................................................................................... 22 10.7 Vibration Strength (without packing) ...................................................................................... 23 10.8 Vibration Strength (in individual packing) ............................................................................... 23 10.9 Drop Impact Strength (without packaging) ......................................................................... 23 10.10 Drop Impact Strength (in individual packaging).................................................................. 23 10.11 Electrical Specifications ...................................................................................................... 23 10.12 Regulatory Compliance ............................................................................................. 24 11 LED Safety ............................................................................................................................. 24 11.1 Product Safety ........................................................................................................................ 24 11.2 EMC ........................................................................................................................................ 24 11.3 RoHS ........................................................................................................................... 24 12 Reliability .................................................................................................................... 24 13 Precautions ................................................................................................................. 25 14 Product Display .......................................................................................................... 26 15 Product Label ......................................................................................................................... 26 15.1 UL Label ................................................................................................................................. 26 15.2 Packaging Specifications .......................................................................................... 27 16 Individual Packaging Specification (RS-232C) ....................................................................... 27 16.1 Individual Packaging Specification (USB) .............................................................................. 28 16.2 Collective Packaging Specification ........................................................................................ 29 16.3 Physical Features ....................................................................................................... 30 17 Dimensions ............................................................................................................................. 30 17.1 Weight .................................................................................................................................... 30 17.2 Mechanical Drawing ............................................................................................................... 30 17.3 Factory Setting ........................................................................................................... 31 18 Default Setting (Part 1: Readable Codes) .............................................................................. 31 18.1 Default Setting (Part 2: Read Options, Illumination LED, Trigger, Buzzer) ........................... 32 18.2 Default Setting (Part 3: Communication Settings).................................................................. 33 18.3 18.3.1 RS-232C ......................................................................................................................... 33 18.3.2 USB ................................................................................................................................. 33 Optional AC Adapter .................................................................................................. 34 19

19.1 Mechanical Drawing / Dimensions ......................................................................................... 34 19.2 Table of Figures Figure 1: Detailed View of F-100 SR ....................................................................................................... 5 Figure 2: Reading distance ...................................................................................................................... 8 Figure 3: Optical axis and Dead zone ..................................................................................................... 8 Figure 4: Scan area and resolution ....................................................................................................... 10 Figure 5: Barcode width ......................................................................................................................... 11 Figure 6: Pitch, Skew and Tilt ................................................................................................................ 12 Figure 7: Curvature ................................................................................................................................ 12 Figure 8: Barcode moving vertically ...................................................................................................... 13 Figure 9: Barcode moving horizontally .................................................................................................. 13 Figure 10: RS-232C D-Sub9pin Connector ........................................................................................... 14 Figure 11: Interface Circuit (RS-232C D-sub 9pin) ............................................................................... 15 Figure 12: RS-232C D-sub 9pin Interface Cable................................................................................... 15 Figure 13: Interface Circuit (RS-232C Loose End)................................................................................ 17 Figure 14: RS-232C Loose End Interface cable.................................................................................... 17 Figure 15: USB Plug (A) Pin Assignment .............................................................................................. 18 Figure 16: Interface Circuit (USB) ......................................................................................................... 19 Figure 17: USB Interface Cable ............................................................................................................ 19 Figure 18: Ambient Light Immunity ........................................................................................................ 21 Figure 19: Scan key durability ............................................................................................................... 22 Figure 20: Cable Bending Strength ....................................................................................................... 22 Figure 21: Drop Impact Strength ........................................................................................................... 23 Figure 22: Product Label ....................................................................................................................... 26 Figure 23: UL Label ............................................................................................................................... 26 Figure 24: Individual Packaging (RS-232C) .......................................................................................... 27 Figure 25: Individual Packaging (USB) ................................................................................................. 28 Figure 26: Collective Packaging ............................................................................................................ 29 Figure 27: Mechanical Drawing ............................................................................................................. 30 Figure 28: AC adapter Mechanical Drawing .......................................................................................... 34 Figure 29: DC plug Mechanical Drawing ............................................................................................... 34 Figure 30: AC plug Mechanical Drawing ............................................................................................... 34

linear imager scanner capable of reading up to 80mm wide barcodes. Overview 2 The F-100 SR is a small size fixed position 1D linear imager scanner that allows for high speed reading of up to 80mm wide barcodes at a distance of 35mm. Its main features are as follows:  Industry’s smallest size A new optical system enabled us to create the smallest fixed mount scanner in the industry without compromizing the performance.  High-speed 700 scans/second Industry’s fastest class 700 scans/second makes reading of high speed moving barcodes possible.  Reliable reading Reliable and instant reading of up to 80mm wide barcodes at a distance of 35mm.  Installation assistant function The F-100 features a read rate mode in which the reading performance is indicated by a 3-color status LED and the buzzer. This mode greatly simplifies the optimal installation in your application.  Configure / Waveform acquisition application To configure the F-100, the “Universal Config” PC program is available which can generate serial commands and menu barcodes. It is also possible to acquire waveforms for analysis of the reading performance.  120mm width model The F-100 SR is capable of reading up to 80mm wide barcodes at a distance of 35mm. For applications that use wider barcodes there is also the WA model, capable of reading up to 120mm wide barcodes at a distance of 64mm. This allows for the use of an imager based scanner in applications that were previously only possible with laser scanners.  The scanner is a RoHS compliant product as declared by OPTOELECTRONICS Co., Ltd.

Model name Focus Interface Cable length Optional AC Adapter F-100 SR or WA -RS232C None None or +PS -USB-COM or -USB or -RS232C(9P) or -RS232C(LE) None Standard 3.1 The following specs are the standard products. Standard Description F-100 SR-RS232C 80mm width model, RS-232C F-100 SR-USB 80mm width model, USB-HID F-100 WA-RS232C 120mm width model, RS-232C F-100 WA-USB 120mm width model, USB-HID Note: Other combinations only as special order, please contact sales offices for this. Model Description 3.2  Reading width / Focus Symbol Description SR 80mm width model (focus distance: 35mm) WA 120mm width model (focus distance: 64mm)  Interface Cable Symbol Description -RS232C RS-232C cable (external AC adapter power supply spec) is connected. -USB-COM USB cable is connected and interface default setting is USB-COM. -USB USB cable is connected and interface default setting is USB-HID. -RS232C(9P) RS-232C cable (power supply input connected to D-sub 9 pin 9) is connected. -RS232C(LE) RS-232C loose end cable is connected.  Cable length Symbol Description None Cable length 2.0m Note: Interface cable length is customizable only as special order.  Optional AC adapter Symbol Description None AC adapter not included. +PS AC adapter for RS-232C external power supply is included.

Default: 9600 bps USB Full Speed 12 Mbps (HID/COM) Indicator Status LED Upper panel 3 colors LED (Green, Orange, Red) Buzzer Rumble at 3000Hz when reading success Optical Section Linear Sensor Technology Linear imager sensor Effective pixels 2496 x1 pixels Scan rate 700 scan/sec Light source Red LED x 2pcs Wavelength: 624nm Supported 1D Symbologies Symbologies 1D Code UPC-A/E, UPC Add-on, EAN-13/8, EAN Add- on, JAN-13/8, Industrial 2 of 5, IATA, Interleaved 2 of 5, Codabar, Code 39, Code 93, Code 128, MSI/Plessey, ISBN code, Code-11, Korean Postal Authority code(Code 3 of 5), UK/Plessey, GS1 DataBar(RSS), S- Code, Telepen, Tri-Optic Minimum resolution Code 39: 0.125mm PCS 0.9 Skew: 15° Pitch, Tilt: 0° Room temperature, room humidity Ambient Light: 500 to1000lx Curvature Radius ≥ 30 mm (EAN/JAN-13) Radius ≥ 20 mm (EAN/JAN-8) Barcode width Possible to read: Code 39 with 80 mm width and resolution 0.19mm (DOF: 35 mm) Depth of Field Code 39 Resolution (0.125-) 30 - 40mm Resolution (0.19-) 25 - 45mm Scan angle Pitch ±6° Skew excludes the dead zone (-10° < β < 10°) Skew -30° ≤ β ≤ -10°, 10° ≤ β ≤ 30° Tilt ±10° Minimum PCS 0.45 or higher Power Section Operating voltage 5.0V ±5% Current consumption Reading 340mA (Typ), 500mA(Max) Ambient temperature: 25°C Standby 100mA (Typ) Note: This product is intended to be supplied by a Listed Power Unit marked "Class 2" or "LPS" and rated from 5Vdc±5%, minimum 0.5A.

Humidity Operating 20 to 85% (No condensing, no frost) Storage 20 to 90% (No condensing, no frost) Ambient light immunity Fluorescent light Incandescent light 5,000 lx or less EAN/JAN 0.26mm Optical axis angle 75° Distance 35 mm Sun light 10,000 lx or less Vibration Vary the frequency of vibration from 10 Hz to 100 Hz at an acceleration velocity of 19.6m/s2 for 60 minutes in X, Y and Z- directions Drop Drop the scanner 18 times (6 faces x 3) from the height of 60 cm onto a concrete floor Dust and drip proof IP42 equivalent Regulatory Compliance Product safety UL60950-1,CSA C22.2 No.60950-1-07 LED safety IEC 62471:2006 Exempt Risk Group Peak Wavelength : 624 nm EMI/RFI VCCI/EN55032/FCC Class B For residential, commercial and light- industry environments European conformity CE marking Electromagnetic compatibility (EMC) EN55024 (EN61000-6-1) Class B For residential, commercial and light- industry environments Immunity Test ESD immunity No destruction Air discharge (direct):±15 kV Condition: IEC61000-4-2 compliant No malfunction Contact discharge (direct / indirect): ±6kV Air discharge (direct):±8 kV Radio- frequency electromagn etic field. Amplitude modulation Frequency 80 to 1000 MHz Condition: IEC61000-4-3 compliant Level 3 V/m AM 80% (AM) Fast transient Voltage Alternating-current input cable: ±1 kV Condition: IEC61000-4-4 compliant Pulse 5 / 50 ns (Tr / Tw) Frequency 5 kHz Surge Pulse 1.2 / 50 ns (Tr / Th) Condition: IEC61000-4-5 compliant Voltage From L to P : ±2 kV (closed-loop voltage) From L to L : ±1 kV (closed-loop voltage) Radio- frequency common mode Frequency 0.15 to 80 MHz Condition: IEC61000-4-6 compliant Level 3 V AM 80% (AM) Power frequency magnetic field Frequency 50 and 60 Hz Condition: IEC61000-4-8 compliant Level 3 A/m Voltage dip, momentary voltage drop, fluctuation Dip 1 Drop 30%, 0.5 cycles Condition: IEC61000-4-11 compliant Dip 2 Drop 60%, 5 cycles Momentary drop Drop 95%, 250 cycles Physical Features Dimensions Approx. 45.5 (W) ×20.25 (D) ×19 (H) (mm) Except protruding portion Weight Approx. 15g Excluding the cable Housing color Black Switch plate color Black

No. Name Description 1 Scan key By pressing this key, the scanner starts reading barcodes. Pressing for more than 5seconds, the scanner shifts to read rate mode. Ends by pressing key again or inputting trigger signal. 2 Status LEDs Indicates reading result and USB communication status. In read rate mode, the read rate is indicated by these 3-color LEDs. Refer to section 5.2 for details. 3 Scan Window Light paths of the imager and LED illumination. Ensure that the lens is free from dust and dirt before scanning. 4 Mounting holes Screw holes that can be used to mount the scanner. Screw hole is M3, maximum depth is 4mm and tightening torque is 0.5 Nm. ④ ③ ① ②

5.2 The status LED’s indicate the reading result and USB communication status. In read rate mode, the reading success rate is indicated by these three 3-color LED’s. Below is a more in-deapth description on these LED’s.  Normal LED indication LED Status LED Status LED Status Reading success Waiting for USB connection Communication/ reading error  Read rate mode LED indication By pressing the scan key for more than 5 seconds or by sending a serial command, the scanner shifts to read rate mode. The status LED’s then show the read rate according to the following table. To exit read rate mode, either press the scan key, send a serial command or activate the trigger signal. Reading rate Less than 50% Less than 75% Less than 95% 95% or more Marking beside status LED Status LED * Status LED legend : OFF : Blinking : ON Note: Refer to the user’s manual for more details.

the imager section, a ‘Communication Control Section’ that takes care of the communication with a host and finally a ‘Power Supply Section’ that generates the power supply voltages for the entire scanner. RS-232C Specification 6.1 Input power supply voltage DC 5.0 V Range of working voltage 4.75 to 5.25 V Power ripple 100 mVp-p max (10 to 100 kHz, power supply voltage 5.0 V) Current consumption* 340 mA (Typ.), 500mA (Max) during reading operation 100 mA (Typ.) in stand-by mode USB Specification 6.2 Input power supply voltage 500 mA (High-Power) Current consumption* 340 mA (Typ.), 500mA (Max) during reading operation 100 mA (Typ.) in stand-by mode * The current consumption was measured at 25°C. The current consumption was measured by placing a 1Ω series resistor in the power supply lines and by measuring the voltage across this resistor. Current value may very depend on the connected host type.

7.1 Item Characteristics Scanning Technology Linear imager sensor - Number of effective pixels Line sensor 2496 x 1 pixels Image capture speed (*1) Scan speed 700±10% scan/s Focal distance Distance from the front edge of scanner 35mm Illumination light source (LED × 2) Red LED 624nm *1 The fastest speed of image capture Focal Plane 7.2 The focal plane is located at 35mm from the front of the scanner. This is the position where the optical performance is at its best. It is recommend to set the barcode at this position, especially when reading a high resolution or a low PCS barcode. It is possible to read up to 80mm wide barcodes at this distance. Figure 2: Reading distance Optical Axis and Dead Zone 7.3 The optical axis is at 6.25±1mm from the bottom of the scanner. Please make sure to position the barcode in this area and respect the possible tolerance. Make sure to tilt the barcode at least by ±10°. The scanner may be unable to read when the barcode has a tilt angle between 0° and ±10° due to specular (mirror like) reflection. Figure 3: Optical axis and Dead zone Focal Plane (F.P) 80 35 [Unit: mm] Barcode Dead zone 0 to 10° 0 to 10° Dead zone Optical axis (6.25) [Unit: mm]

Conditions Ambient Temperature and Humidity Room temperature, room humidity Ambient Light 500 to 1500 lux Angles α = 0°, β = +15°, γ = 0° (refer to figure 6) Curvature R = ∞ Power Supply Voltage 5.0 V PCS 0.9 or higher Scanning Test More than 630 times success during 700 scans. Barcode Test Sample Specified in each section Barcode Test Sample 8.1 Code39 Resolution Code type PCS Barcode width* Quiet Zone Digits 1.0mm Code 39 0.9 53mm 20mm 1 0.5mm 54mm 10mm 4 0.25mm 42mm 5.1mm 8 0.19mm 60mm 5.1mm 17 80mm 5.1mm 24 0.15mm 60mm 5.1mm 10 0.125mm 16mm 5.1mm 4 0.19mm 0.45 60mm 5.1mm 17 EAN/JAN Resolution Code type PCS Barcode Width* Quiet Zone Digits 0.26mm EAN/JAN 0.9 30mm 10mm 13 0.26mm EAN/JAN 0.9 22.5mm 10mm 8 * The width includes the quiet zone.

Figure 4: Scan area and resolution When the barcode print quality or the conditions stated at the beginning of section 8 are not satisfied, the above reading range may not be reached. Please check the readability beforehand and decide appropriate installation conditions. Depth of Field 8.3 Code Resolution (mm) Code type PCS Depth of Field (mm) Maximum reading width 0.125 – below 0.19 Code 39 0.9 35±5 60mm 0.19 – 1.08 Code 39 0.9 35±10 80mm Note: Maximum reading width of the barcode includes the quiet zone. 35 5 5 10 10 60 80 Resolution: 0.125 - Resolution: 0.19 - [Unit: mm]

8.4 PCS 0.45 or higher Conditions MRD ≥ 32% (≥ 80% reflectivity of space and quiet zone) Distance 35 mm from the front edge of the scanner Barcode width Maximum 60mm Barcode Code 39. Resolution = 0.19mm / PCS 0.45, specified in Section 8.1. MRD = Minimum reflectance of white space – Maximum reflectance of black bar PCS = Reflectance of white space – Reflectance of black bar. Reflectance of white space Note: Be sure to keep the optical window clean without dirt or scratches, or it may deteriorate the reading performance. Minimum Resolution 8.5 0.125mm (Code 39 specified in Section 8.1) Conditions Bar code Above code specified in Section 8.1. Distance 35±5 mm from the front edge of the scanner Angle α = 0°, β = + 15°, γ = 0° Curvature R = ∞ Barcode Width 8.6 80 mm Conditions Barcode Code 39. Resolution = 0.19mm / PCS 0.9, specified in Section 8.1. Distance 35 mm from the front edge of the scanner Angle α = 0°, β = + 15°, γ = 0° Curvature R = ∞ Figure 5: Barcode width 80 [Unit: mm] 35

8.7 Pitch α = ±6° Skew -30° ≤ β ≤ -10°, 10° ≤ β ≤ 30° Tilt γ = ±10° Conditions Barcode Code 39. Resolution = 0.19mm / PCS 0.9, specified in Section 8.1. Distance 35 mm from the front edge of the scanner Curvature R =∞ Angle Pitch β = +15°, γ = 0° Skew, Dead zone α = 0°, γ = 0° Tilt α = 0°, β = +15° Figure 6: Pitch, Skew and Tilt Curvature 8.8 0.26 mm 13-digit EAN/JAN R ≥ 30 mm 0.26 mm 8-digit EAN/JAN R ≥ 20 mm Conditions Barcode Sample EAN/JAN PCS 0.9 specified in Chapter 8.1 Distance 35 mm from the front edge of the scanner Angle α = 0°, β =+15°, γ = 0° Figure 7: Curvature Tilt Pitch Skew α β γ - - + + + - R Barcode 35 [Unit: mm]

almost the same performance as when it is reading non moving barcodes. The scanning performance is only reduced when a barcode is moved at very high speed or when the height of the barcode is very small. Figure 8: Barcode moving vertically However, when scanning barcodes that are moving horizontally as shown in figure 9, the scanning performance will be reduced rapidly at increasing speed. Therefore, make sure to stop the barcode for a brief moment when the barcode is aligned at the center of the scanner. Figure 9: Barcode moving horizontally Note: When scanning barcodes on moving items as described above, scanning performance may decline rapidly, depending on operating conditions. t

RS-232C Interface (D-Sub 9pin) 9.1 9.1.1 Initial Communication Settings Basic communication specs are as follows. Item Communication spec Default setting Baud rate 150 to 115200 bps 9600 bps Data length 7 / 8 bits 8 bits Parity bits None / Even / Odd parity None Stop bits 1 / 2 bit 1 bit 9.1.2 Signal Specification Signal names are based on the signals transmitted from the scanner to the host. Signal Level RS-232C communication line Signal Name IN/OUT Voltage(V) Mark Space TxD OUT -5 to -15 +5 to +15 RxD IN -3 to -15 +3 to +15 RTS OUT -5 to -15 +5 to +15 CTS IN -3 to -15 +3 to +15 9.1.3 Pin Assignment Signal Name Pin No. Note (NC) 1 Open (not connected) TxD 2 RS-232C communication line RxD 3 RS-232C communication line (NC) 4 Connect to pin 6 GND 5 (NC) 6 Connect to pin 4 CTS 7 RS-232C communication line RTS 8 RS-232C communication line (NC) 9 Open (not connected) 1 6 5 9 Figure 10: RS-232C D-Sub9pin Connector

Figure 11: Interface Circuit (RS-232C D-sub 9pin) 9.1.5 RS-232C D-Sub 9pin Interface Cable Cable length 2000 mm Wire conductors diameter AWG28 Cable diameter φ3.8mm Weight Approx. 75g Figure 12: RS-232C D-sub 9pin Interface Cable Barcode reader main circuit VCC TxD RxD RTS CTS S-GND F-GND TxD RxD CTS RTS External device F-100 DC JACK φ3.8 10 2000+50 0 100±10

9.2 9.2.1 Initial Communication Settings Basic communication specs are as follows. Item Communication spec Default setting Baud rate 150 to 115200 bps 9600 bps Data length 7 / 8 bits 8 bits Parity bits None / Even / Odd parity None Stop bits 1 / 2 bit 1 bit 9.2.2 Signal Specification Signal names are based on the signals transmitted from the scanner to the host. Signal Level Sequencer Signal (loose end only) Signal Name IN/OUT Voltage(V) ON OFF Trigger IN 0V to 1.5V 3.0 V to Vcc OK OUT 0.3V/5mA OC output/24V(max)* NG OUT 0.3V/5mA OC output/24V(max)* * OC output: Open Collector output 9.2.3 Pin Assignment Signal Name Pin No. Note TxD Green RS-232C communication line RxD White RS-232C communication line RTS Gray RS-232C communication line CTS Blue RS-232C communication line Trigger Brown External trigger input terminal S-GND Black Signal line GND Vcc Red Power-supply (5V) NG Orange NG output terminal OK Yellow OK output terminal F-GND Black (tick) Frame GND (cable shielded wire)

Figure 13: Interface Circuit (RS-232C Loose End) 9.2.5 RS-232C Loose End Interface Cable Cable length 2000 mm Wire cable length 60mm Wire conductors diameter AWG28 Insulator outer deameter 0.58mm Wire length 7mm Cable diameter φ3.8mm Weight Approx. 55g Figure 14: RS-232C Loose End Interface cable Barcode reader main circuit VCC DC 5V + load Maximum DC 24V + TxD RxD RTS CTS OK / NG Trigger Trigger S-GND F-GND TxD RxD CTS RTS External device F-100 2000 φ3.8 60 7 ±5 ±1 [Unit: mm] ±50

(Communication Device Class). COM allows for bidirectional serial communication and is used for command transmission from the host device to the scanner in addition to receiving barcode data. Note: For the USB-COM interface model, the Opticon USB-COM driver must be installed on your host device. Please use the latest of the USB-COM version driver. While using USB-COM and the host COM port is not actively open, scan data cannot be sent and F-100 SR will make an error sound. 9.3.1 USB Interface Specifications Bus-power class 500 mA (high-power) Speed Full speed (12 Mbps) Interface HID/COM (Virtual COM Port) Note: The USB interface models are bus powered and no AC adapter is needed. Do not use the host keyboard when using USB-HID to transmit barcode data. Data may be lost as a result. Item Explanation Transfer Speed USB2.0 Full Speed Vendor ID 065A Product ID (HID) 0001 Product ID (COM) 0009 9.3.2 USB Connector Pin No. Signal name 1 VBUS 2 D- 3 D+ 4 GND Figure 15: USB Plug (A) Pin Assignment 1 2 3 4 Front View

Figure 16: Interface Circuit (USB) 9.3.4 USB Interface Cable Cable length 2000 mm Cable diameter φ3.8mm Weight Approx. 60g Figure 17: USB Interface Cable Full Speed USB Transceiver Buffers +3.3V Pin No. Signal 1 VBUS 2 D- 3 D+ 4 GND Shell FG USB A Connector 2000 φ3.8 ±50 #1 #4 [Unit: mm]

Operating Temperature 0 to 40 °C Storage Temperature -10 to 60 °C Conditions Barcode EAN/JAN-13 Resolution = 0.26 mm / PCS 0.9, specified in chapter 8.1 Distance 35 mm from the front edge of the scanner Angle α = 0°, β =15°, γ = 0° Curvature R = ∞ Humidity 10.2 Scanning performance is guaranteed when the ambient humidity is within the following ranges: Operating Humidity 20 to 85%RH (no condensation, no frost) Storage Humidity 20 to 90%RH (no condensation, no frost) Conditions Barcode EAN/JAN-13 Resolution = 0.26 mm / PCS 0.9 Specified in chapter 8.1 Distance 35 mm from the front edge of the scanner Angle α = 0°, β =15°, γ = 0° Curvature R = ∞

10.3 Scanning performance is guaranteed when the illumination on a barcode surface is between zero and the following values: Incandescent light 5,000 lx Fluorescent light 5,000 lx Sunlight 10,000 lx Conditions Barcode EAN/JAN-13 Resolution 0.26 mm / PCS 0.9 specified in chapter 8.1 Distance 35 mm from the front edge of the scanner Illuminance Illuminance is uniform on the barcode surface. Angle α = 0°, β = +15°, γ = 0° Curvature R = ∞ Figure 18: Ambient Light Immunity Note: Avoid direct or specular reflection from the light source to get the best scanning performance. When the illuminance is not uniform on the barcode surface, the scanner may fail to read. Dust and Drip Proof 10.4 IEC IP42 equivalent Protection against solid objects: Level 4 equivalent Protected against solid objects greater than 1.0 mm Protection against liquids: Level 2 (JIS IPX2)* equivalent Protected against dripping water from the vertical when tilted up to 15° * () is JIS drip-proof type. Illuminance measuring surface 15 35

10.5 Activating the scanner by pressing the trigger shall be possible after the following scan key strength test. Scan Key Strength Test: Affix the scanner as shown in the following picture. Press and release the scan key by a push rod with a diameter of 10mm with a force of 9.8N (1kgf) and repeat this 5 million times. Figure 19: Scan key durability Cable Strength 10.6 There shall be no malfunction after the following cable strength test. Cable Strength Test: Affix the scanner to an immovable object and pull the cable using a force of 24.5N (2.5 kgf static loading) for 60 seconds. Cable Bending Strength 10.7 There shall be no malfunction after the following cable bending test. Cable Bending Test: Add a load of 4.9 N (500 gf) to the cable and flex it 60° in both directions. Repeat this 700 times. Figure 20: Cable Bending Strength 60° 60°

10.8 There shall be no malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an acceleration velocity of 19.6m/s2 (2.0 G) for 30 minutes in the non-operating state. Repeat this twice for each of X, Y and Z direction. Vibration Strength (in individual packing) 10.9 There shall be no malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an acceleration velocity of 19.6 m/s2 (2.0 G) for 30 minutes in individually packaged state. Repeat this twice for each of X, Y and Z direction. Drop Impact Strength (without packaging) 10.10 There shall be no malfunction after the following drop test. Drop test: Drop the scanner 18 times (3 times at each of 6 orientations), from a height of 60 cm onto a concrete floor. Figure 21: Drop Impact Strength Drop Impact Strength (in individual packaging) 10.11 There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. Electrical Specifications 10.12 Electrostatic discharge* immunity* No destruction ±15 kV (air discharge, direct) No malfunction ±8 kV (air discharge, direct) ±6 kV (contact discharge, direct / indirect) * Testing method is compliant with IEC-61000-4-2. (150 pf, 330 ohm) 60cm Concrete floor

conditions: ( 1 ) this device may not cause harmful Interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation. Regulatory Compliance 11 LED Safety 11.1 IEC 62471:2006 Exempt Risk Group Product Safety 11.2 UL 60950-1, 2nd Edition, 2014-10-14 CAN/CSA C22.2 No. 60950-1-07, 2nd Edition, 2014-10 IEC 60950-1:2005 +A1:2009 +A2:2013 EN 60950-1:2006 +A11:2009 +A1:2010 +A12:2011 +A2:2013 EMC 11.3 EN 55032:2012 EN 55024:2010 FCC Part 15 Subpart B Class B VCCI-CISPR 32:2016 Class B RoHS 12 RoHS compliance. RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2011/65/EU Reliability 13 MTBF (Mean Time Between Failures) 50,000 hours Note: This is calculated based on standard operation of the product within the operating environment parameters and without extreme electronic or mechanical shock. This is a Class B product, to be used in a domestic environment, based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.

(1) Shock: ・ Do not drop this product from a height greater than specified in this manual. ・ Do not swing the product around by the cable. ・ Do not place this product under or between heavy items. (2) Temperature Conditions: ・ Do not use this product at temperatures outside the specified range. ・ Do not pour boiling water on this product. ・ Do not throw this product into fire. ・ Do not bend the cable at extremely low temperatures. (3) Foreign Materials: ・ Do not immerse this product in water or any other liquid. ・ Do not expose this product to chemicals. (4) Others ・ Do not plug/unplug the connectors while power is supplied. ・ Do not disassemble this product. ・ This product may be affected by a momentary voltage fluctuation caused by lightning. ・ Do not wrap F-100 SR cable around a host device (PC, tablet etc.). This may cause malfunction.

Refer 17.3 (Mechanical Drawing) for the allocation. Figure 22: Product Label UL Label 15.2 Example of UL label attached to the scanner is shown below. Refer 17.3 (Mechanical Drawing) for the allocation. Figure 23: UL Label

16.1 Package size Approx. 122 x 112 x 38 (WDH mm) Weight Approx. 105 g (RS-232C model) Figure 24: Individual Packaging (RS-232C) BOX Mirror mat * Short side down. Place the bundled cable under the mirror mat. Put QUICK START GUIDE on top. Do not fold at the Barcode position, when stick label on to the box. BARCODE LABEL for BOX Display for the serial-No. From『 000001 』to 『 999999 』 Same number as the scanner. Number of six digits. *Continuous Number. Twist ties QUICK START GUIDE(ENG)

16.2 Package size Approx. 122 x 112 x 38 (WDH mm) Weight Approx. 110 g (USB model) Figure 25: Individual Packaging (USB) BOX Mirror mat * Short side down. Place the bundled cable under the mirror mat. Put QUICK START GUIDE on top. Do not fold at the Barcode position, when stick label on to the box. BARCODE LABEL for BOX Display for the serial-No. From『 000001 』to 『 999999 』 Same number as the scanner. Number of six digits. *Continuous Number. Twist ties QUICK START GUIDE(ENG)

16.3 Assembled package size Approx. 588 × 514 × 285 (WDH mm) Weight Approx. 14 kg (RS-232C model) Approx. 12.5 kg (USB model) ‘Ro mark’ on the trays and boxes indicates that the product is RoHS compliant as is declared by OPTOELECTRONICS Co., Ltd Figure 26: Collective Packaging Note: The above drawing shows the collective packing example of a RS-232C model. 【原産国表示】～country of origin～ 中国生産（produced in China）＝MADE IN CHINA 日本生産（produced in Japan）＝MADE IN JAPAN ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑬ ⑪ ⑫ ⑭ ⑮ ⑲ ⑱ ⑰ ⑯ ⑳ Packaged 100 sets into the carton box. CARTON BOX Barcode Serial Label Missing Serial Number Label Barcode Serial Label for Packaging Box: Stick the labels on both front and back side of the box. Missing Serial Number Label: Attach this label when there are more than 3 labels of which serial numbers are out of order (not in a correct sequence). • C/No.△△ 3 * △ △ △ △ △ △ * Missing Serial Number Missing Q'ty △△ 4 5 6 7 8 9 1 0 1 1 1 2 * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * * △ △ △ △ △ △ * OPTOELECTRONICS CO.,LTD. MADE IN ▲▲▲▲▲ OSE C/No.△△ MADE IN ▲▲▲▲▲ Product Spec#EUR Q'ty *△△* △△/△△△ S/N(from) S/N(to) Missing Serial Number Missing Q'ty △ 1 *△△△△△△* 2 *△△△△△△* Shipping Date 20△△/△△/△△ OPTOELECTRONICS CO.,LTD. Ｒｏ *△△△△△△* *△△△△△△* ROM Ver. TC24J01 OSE PO# Spec#USA Spec#JPN *△△△△- △△* *OF1F100B* F-100 SR-RS232C *XXXXX* *XXXXXXX-XX* TC24J△△

Weight 17.2 Approx. 15 g (excluding cable) Mechanical Drawing 17.3 Figure 27: Mechanical Drawing Mounting holes M3 Depth4 Scan window Illumination LED lens Imaging lens Scan key Status LED (30) (12.8) (19) (6.25) (20.25) (45.5) [Unit: mm]

18.1 Code type Read Minimum digits Transmit CD Calculate CD Transmit other Prefix Suffix UPC-A  -   - RS-232C USB- COM “CR” / USB-HID “ENTER” UPC-A Add-on  -   UPC-E  -   UPC-E Add-on  -   EAN-13  -   EAN-13 Add-on  -   EAN-8  -   EAN-8 Add-on  -   Code 39  1   Not transmit ST/SP Tri-Optic  - - - Codabar / NW-7  5   Not transmit ST/SP Industrial 2 of 5  5   Interleaved 2 of 5  6   S-Code  5   Code 93  1 -  Code 128  1 -  GS1-128 (EAN-128) *5  1 -  MSI/Plessey  3 CD1 CD1 UK/Plessey  2   Telepen  1   Matrix2of5  5   IATA  5   CODE11  1   GS1 DataBar Omnidirectional (RSS-14)  -   Transmit AI GS1 DataBar Expanded (RSS Expanded)  1 -  GS1 DataBar Limited (RSS Limited)  -   Transmit AI GS1 DataBar Truncated (RSS-14 Truncated)  -   Transmit AI (1) “Reading” column  Read  Not read - Not supported (2) “Transmit CD” column  Transmit  Not transmit - Not supported (3) “Calculate CD” column  Calculate  Not calculate - Not supported (4) “Prefix” column - No prefix setting (5) GS1-128 (EAN-128) barcodes are processed as Code 128 and “FNC1” data will be ignored.

18.2 Item Default Setting the number of characters Fixed length OFF all codes Read mode Single read Multiple read reset time 500 msec Add-on wait mode 500 msec Redundancy*1 Read 1 times, redundancy = 0 Multiple columns read Disable multiple columns read Read time 2seconds Trigger input Enable Buzzer durations 50msec Buzzer tone 3.0kHz Buzzer loudness Loud (maximum) Indicator duration (Green LED) 200msec (*1) In case of the following symbologies, because of the prevention of miss-decoding, the reading times are increased once and redundancy is also increased once. Symbology Length Code 39 5 or less Codabar / NW-7 All IATA 8 or less Industrial 2 of 5 8 or less Interleaved 2 of 5 8 or less MSI/Plessey 4 or less Code 11 5 or less TELEPEN 8 or less S-code 7 or less Matrix 2 of 5 8 or less Chinese Post Matrix 2 of 5 8 or less Code 128 2 or less

18.3 18.3.1 RS-232C Item Default Baud rate 9600 bps Parity bit None Data bit 8 bits Stop bit 1 bit Handshaking No ACK / NAK No CTS time out Indefinitely ACK / NAK time out 1 sec Command header ESC Command terminator CR Response to command Disable 18.3.2 USB Item Default Keyboard language USA (USB-HID) Send “new line key “after data Enable Send “TAB key “after data Disable Send “→ key “after data Disable Other CDC-ACM compliant (USB-COM)* * The Opticon USB-COM driver must be installed on your host to use in USB-COM. Please contact sales offices for the manual and setting tools.

19 Electrical Specifications 19.1 Rated output voltage 5.0V Rated output current 2.0A Mechanical Drawing / Dimensions 19.2 Figure 28: AC adapter Mechanical Drawing Figure 29: DC plug Mechanical Drawing Figure 30: AC plug Mechanical Drawing 71.3 1 1800 45 53.6 1 16.1 0.2 32.6 1 69.0 1 [Unit: mm] 4.0 1.7 EIAJ Voltage type2 (EIAJ#2) [Unit: mm]