OpenEye OE-C3012T4 Quick Start Manual

All Rights Reserved. Information contained in this document is subject to change without prior notice. OpenEye does its best to provide accurate information but cannot be held responsible for typos or mistakes. Liberty Lake, WA, USA 509.232.5261 openeye.net QUICK START GUIDE OE-C3012T4 4MP | Autofocus | Turret This quick start guide provides only basic information on the camera’s settings and operation for initial installation. Please read the user manual for optimal camera confi gurations. 37465AB openeye.net CONNECTIONS 1 RJ-45 RJ-45 For network and PoE connections For network and PoE connections 2 Power Power (12vDC) (12vDC) 1 12vDC 12vDC Power connection Power connection 11 2 Waterproof Cable 1 Thread lock cap Thread lock cap 4 Rubber “O” ring Rubber “O” ring 2 Rubber plug Rubber plug 5 Camera cable Camera cable 3 RJ45 enclosure RJ45 enclosure 5 4 3 2 1 1 1 Reset Button Reset Button To restore the camera to factory To restore the camera to factory defaults: defaults: 1. 1. Disconnect power for 30 Disconnect power for 30 seconds. seconds. 2. 2. Reconnect power and wait Reconnect power and wait 30 seconds. 30 seconds. 3. 3. Press and hold the reset Press and hold the reset button for 20 seconds. button for 20 seconds. 2 MicroSD Card Slot MicroSD Card Slot Supports up to 512GB microSD Supports up to 512GB microSD card for Edge storage. card for Edge storage. Do not add or remove the Do not add or remove the microSD card when the camera microSD card when the camera is powered on. is powered on. 2

and Power over Ethernet (PoE). If you are connecting 12vDC power, verify the polarity of the power connection. CONTENTS Selecting multiple cameras and enter- ing IP address 192.168.51.2 will set an IP address on all selected cameras, starting at 192.168.51.2 and increase per camera. 1. Open the Network Camera Manager application. 2. Select applicable camera(s). 3. Input starting IP address, Subnet Mask, Gateway, DNS. OE-C3012T4 Turret Camera PRODUCT FEATURES Camera Maximum Resolution 2688x1520 Frame Rate at Maximum Resolution 30FPS @ 4MP H.264/H.265 Total Streams Dual Streaming ONVIF Profi le S / G / T Compliant Day/Night True Day / Night Wide Dynamic Range True WDR Environmental and Power Power Consumption 8.16W maximum Input Voltage 12vDC / PoE Operating Temperature -40°~140°F (-40°~60°C ) IP Rating IP67 Self-Tapping Screws & Plastic Anchors Waterproof Cable Connector Quick Start Guide ETHERNET CABLE CONNECTIONS Connect a network cable to the camera using the RJ45 input and connect the other end of the cable to your network switch or recorder. INSTALLATION Connect a network cable to the camera using the RJ45 input and connect the other end of the cable to your network switch or recorder. 1. Apply template sticker to desired camera location. 2. Drill anchor holes using included mounting template. 3. Remove mounting template. 4. Insert anchors. 5. Mount camera. 6. Connect network cable with included waterproof cable connector. 7. Adjust camera view. NOTE: Refer to your Apex recorder manual or quick start guide for instruction on adding cameras. Passwords must be 8-16 characters, contain at least 1 capital and 1 lowercase letter, 1 number, and 1 unique character. Mounting Template ASSIGNING AN IP ADDRESS OpenEye IP cameras are set to DHCP by default. If a DHCP server is not detected after 4 minutes, the camera will default to IP address 192.168.51.2. If you are not using a DHCP server, NCM will allow you to batch confi gure a static IP address. The IP address for the camera network on your Apex recorder is 192.168.51.1. NOTE: To change this IP address please refer to your Apex recorder manual. NOTE: NCM requires entry in all fi elds. 4. Apply changes. 5. Wait 60 seconds before refreshing NCM. CONNECTING TO THE IP CAMERA To access the camera setup menu, you need to open Network Camera Manager (NCM) utility. NCM is pre- installed on all OpenEye Recorders, and is also available for download on the OpenEye website for installation on your personal computer or laptop. 1. Open Network Camera Manager. 2. Locate your camera on the Network Camera Manager list. 3. To open the web browser, select the camera and click LOAD. NOTE: OpenEye IP cameras ship without a default password. DEFAULT USERNAME AND PASSWORD The admin user password can be set using the following methods: 1. OpenEye recorders running Apex 2.1 or newer will automatically set a new unique password if: Connected to an M-Series recorder with a built in PoE switch. Connected to a network switch through the camera network port and selected then added in setup, if a new password has not already been set. 2. Connect to the camera directly through a Web Browser and follow the onscreen prompts. 3. Use the Network Camera Manager (NCM) Utility. Username: admin NOTE: The NCM software manual can be found at https://www.openeye.net/ncm-manual