EAW FB1SB Installation Instructions

FRONT HOLE FOR QUICK DISCONNECT PIN HOLE FOR QUICK DISCONNECT PIN HINGE TUBE 2X USER SUPPLIED SHACKLE 1 2 Eastern Acoustic Works Whitinsville, MA USA Tel: (508) 234-6158 WARNING Working Load Limit (WLL): 2000 lb / 907 kg MAX Twelve (12) SB1002 in succession, 155 lb / 70.3 kg ea. Fly-Bar = 20 lb / 9.1 kg. 1 REMOVE QUICK DISCONNECT PIN 2 3 RAISE HINGE LOWER FLY-BAR AND FULLY INSERT HINGE INTO HINGE TUBE HINGE TUBE HINGE 4 5 1 2 Eastern Acoustic Works Whitinsville, MA USA Tel: (508) 234-6158 WARNING Working Load Limit (WLL): 2000 lb / 907 kg MAX Twelve (12) SB1002 in succession, 155 lb / 70.3 kg ea. Fly-Bar = 20 lb / 9.1 kg. ALIGN HOLES IN HINGE TUBE AND HINGE. FULLY INSERT QUICK DISCONNECT PIN TO LOCK FLY-BAR TO ENCLOSURE ALIGN HOLES IN HINGE TUBE AND HINGE. FULLY INSERT QUICK DISCONNECT PIN TO LOCK FLY-BAR TO ENCLOSURE Installation Instructions FB1SB Fly-Bar & Rigging Warning: Suspending Loudspeakers should be done with extreme caution and by a certified professional who is qualified to determine the requirements for and to implement overhead rigging. Failure to follow proper precautions may result in damage to the equipment, injury, or death. Working Load Limit (WLL): vertical pull FB1SB Fly-Bar WLL: 2000 lb/ 907 kg maximum twelve (12) SB1002 in succession Weights: SB1002: 155 lb/70 kg, Fly-Bar: 20 lb/9 kg ENCLOSURE TO FLY-BAR 1 2 Eastern Acoustic Works Whitinsville, MA USA Tel: (508) 234-6158 WARNING Working Load Limit (WLL): 2000 lb / 907 kg MAX Twelve (12) SB1002 in succession, 155 lb / 70.3 kg ea. Fly-Bar = 20 lb / 9.1 kg. FLY-BAR POSITIONED ABOVE PALLET OF SB1002 LOUDSPEAKERS ENCLOSURE TO ENCLOSURE CASTER PALLET FROM ENCLOSURE Description: The FB1SB Fly-Bar is used to suspend up to 12 SB1002 loudspeakers. These instructions enable a technician to suspend 2 SB1002 Loudspeakers from the Fly-Bar. To suspend additional SB1002 loudspeakers, refer to the SB1002 Installation Manual. Rigging Points on the SB1002 Array: These instructions follow the same sequence a technician must follow when flying an array of SB1002 enclosures. The figure to the right shows, from the top down, the three rigging operations: A. Enclosure to Fly-Bar, B. Enclosure to Enclosure C. Caster Pallet from Enclosure The three rigging operations are defined by the following three assembly illustrations. Rigging tubes, hinges, and their tethered quick disconnect pins are attached to both sides of the SB1002 Loudspeaker. These instructions apply to both the right and left sides of the Fly-Bar, Loudspeakers, and Caster Pallet. To disassemble the array reverse the sequence of the operations defined in these instructions. A. Enclosure to Fly-Bar:

DISCONNECT PIN TO UNLOCK LEFT SIDE OF CASTER PALLET FROM ENCLOSURE RAISE ARRAY UP AND AWAY FROM CASTER PALLET REMOVE RIGHT QUICK DISCONNECT PIN TO UNLOCK RIGHT SIDE OF CASTER PALLET FROM ENCLOSURE 11 10 If you have questions about these FB1SB Fly-Bar & Rigging Installation Instructions please contact the EAW Application Support Group: Tel 800-992-5013 (USA only) Tel 508-234-6158 Fax 508-234-8251 E-mail [email protected] Thank you for purchasing EAW products One Main Street, Whitinsville, MA 01588 tel: 800 992 5013 / 508 234 6158 fax: 508 234 8251 web: www.eaw.com T h e L a w s o f P h y s i c s | T h e A r t o f L i s t e n i n g EAW is the worldwide technological and market leader in the design and manufacture of high-performance professional loudspeaker systems. RD0423 (A) JUNE 07 REMOVE RIGHT AND LEFT QUICK DISCONNECT PINS UNLOCKING HINGES FROM HINGE TUBES RAISE RIGHT AND LEFT HINGES ALIGN HOLES IN HINGES AND HINGE TUBES THEN FULLY INSERT BOTH QUICK DISCONNECT PINS TO LOCK ENCLOSURES TOGETHER 7 8 9 LOWER ENCLOSURE FITTING ITS BOTTOM RUNNERS INTO THE RECESSES ON THE TOP OF LOWER ENCLOSURE RIGHT LEFT 6 C. Caster Pallet from Enclosure: B. Enclosure to Enclosure: STORE QUICK DISCONNECT PINS AS SHOWN SWING DOWN CASTER PALLET’S PIVOT BRACKETS INTO THEIR CLOSED POSITION 13 14 Storing Caster Pallet’s Pivot Brackets & Quick Disconnect Pins