METHVEN Aroha 01-9267 Installation Manual

ABN 15 104 813 390 Melbourne, Australia www.methven.com WMKA21005 IMPORTANT Please read all of the instructions before installation MA019267 Aroha Bidet Mixer 01-9267 Use of this product is recommended for domestic and commercial applications. All pipework must be thoroughly flushed prior to the installation of the mixer. Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles damaging the ceramic head works. Do not remove the ceramic cartridge from the mixer when installing. Methven recommends a licensed plumber carry out all installations in compliance with the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations. June 2012 Installation Guide Installation Tip: Install product on bench before connecting second hose to mixer. 1. Cut a single 35mm diameter hole into the mounting surface. The mounting surface can be a maximum of 40mm thick. 2. Insert o-ring (3) into the groove in the bottom of the mixer (1). 3. Feed the mixer’s (1) threaded fastening tube through the hole cut in the mounting surface. 4. Position the mixer (1) as desired and fit the rubber washer (4) over the threaded fastening tube. Tighten the mounting nut (5) in place using the tube spanner (9) from under the mounting surface. 5. Insert the flexible hoses (7) through the hole in the mounting surface (from the underside) and screw them into the base of the mixer body (1). 6. Connect the flexible hoses to the hot and cold supplies (hot on the left, cold on the right). Note: It is recommended that the inline filter washers supplied are fitted during this connection. 7. Fit “pop-up” waste outlet (B) into Bidet bowl. 8. Remove side nut (C) and insert rod with ball (D). Fit washer supplied and replace side nut (C). 9. Join extension rod (E) to “pop-up” lever (A) under bowl. 10. Using “universal joint” provided (F) join and adjust rods to maintain “pop-up” action. www.methven.com Customer Care Hotline: 1300 METHVEN (638 483) Email: [email protected] Hot Max 40mm ø35mm Min ø38mm Max Cold

HOSE OR SWAGED ENDS CORRECT INCORRECT DO NOT STRETCH OR TWIST HOSES Tube spanner 9 Stream shaper Fast Fit Tube O-Ring Rubber Washer Pop up Waste Flexible inlet hose: cold hot Mounting Nut Mixer Body Technical Specification Inlet Connections: All 1/2" BSP Operating Pressure: 150kPa - 500kPa For optimum performance hot and cold water pressures should be equal. AS/NZS 3500 stipulates a 500kPa maximum operating pressure at any outlet within a building. Where normal pressure exceeds 500kPa, a pressure limiting valve must be installed. Operating Temperature: Recommended hot water supply 50°C, maximum 70°C. AS/NZS 3500 requires all hot water supplies to any sanitary fitting to be tempered to 50°C. Ceramic cartridges: Ceramic cartridge can be damaged due to the presence of the following within the water supply: Copper tube pieces Plastic pieces Sand, dirt or stones Thread tape Other objects not normally present in the potable water supplies Hose Requirement for Mixers Do not hydrostatic test* the installation with this mixer installed. Damage to the ceramic cartridge may occur. *Hydrostatic testing refers to placing the system under pressure, above the recommended operating pressure, to determine water tightness and to uncover leaks or weak joints within the system. Care and Cleaning Never use abrasives to clean this product. Clean regularly with contamination free warm soapy water and a damp soft cloth. www.methven.com Customer Care Hotline: 1300 METHVEN (638 483) Email: [email protected] Pop Up Waste Parts Please check every component in accordance with the table below A Pop up lever 1 B Pop up waste outlet 1 C Nut 1 D Rod with ball 1 E Extension rod 1 F Universal joint 1 F A E B CD 1 3 4 5 7