Mercia Garden Products 0628WKNE0405LBDD2SW-V1 Instructions Manual

22 Gable - 4000mm QTY 2 AI-0628WKNE0405LBDD2SW-G-V1 23 Starter Board - 66x28x4000mm QTY 2 LB28RT66-A-4000 24 Log Board - 120x28x4000mm QTY 19 LB28-A-4000 25 Log Board - 120x28x3036mm QTY 12 LB28-B-3036 26 Log Board - 120x28x232mm QTY 30 LB28-B-232 Log Board - 120x28x232mm QTY 12 LB28-C-232 27 Log Board - 120x28x5000mm QTY 26 LB28-A-5000 Log Board - 120x28x2200mm QTY 18 LB28-B-2200 Log Board - 110x28x5000mm QTY 1 LB28RG110-A-5000 Roof Purlin - 45x120x5004mm QTY 3 F45120-A-5004 Bearer - 44x44x2316mm QTY 26 F4444-2316-PT Bearer ...

P 12 39 Step 19 Parts Needed - No. 39 QTY 44 Place the frst foor board (No. 39) inside the building fush to the log board on one side. Continue adding the foor boards (internally) making sure to interlock each individual board. You have been issued with 44 foor boards, but in reality you may only need to use 43. *Do NOT secure the boards until the last board has been measured and cut. Following the same method outlined previously measure the gap between the bottom of the tongue (on the last board placed) and the log board. Using ...

P 11 40mm screw Pre drill hole *Cut to ft Step 17 Parts needed - No. 40 QTY 92 Place the frst two roof board’s (No. 40) onto the log cabin on each side, making sure the boards are fush to the end of the roof purlin. Once in position fx to each purlin using 3x40mm screws. Use the spacer (No. 43) to create an expansion gap between each roof board if installing during low levels of moisture (summer). This creates an expansion gap for the boards to move into during high levels of moisture (winter). Once in position fx to each pur ...

IMPORTANT : Pre-drill before fxing screws. Pre drill hole 30mm screw Step 26 Parts Needed - No. 18 QTY 2 No. 19 QTY 1 No. 20 QTY 1 Fit the Dead Lock (No. 19) into the recess in the master door (No. 9) and secure using the screws provided. Attach the Key Plate (No. 20) to the slave door (No. 10) with 4x30mm screws. After fxing the Dead lock, add the pull handles (No. 18) with 4x30mm black screws each. Be sure that the screws fx into the framing on the otherside of the door. **You have been provided with an additional set o ...

Once the boards are square, lift up the log board (No. 27) and fx the starter boards in place. Fix each of the starter boards to the frame by screwing through the notch into the frame as shown in the illustration. 4x70mm Screws 23 Pre drill hole 70mm screw Step 4 Parts Needed - No. 23 QTY 2 No. 27 QTY 2 Place the starter boards (No’s. 23) on to assembled base frame along the shortest sides and place the frst two log boards (No. 27) in the notch as shown. Ensure the boards sit squ ...

Step 6 Parts Needed - No. 11 QTY 1 No. 12 QTY 1 No. 13 QTY 1 No. 14 QTY 1 Arrange the left, right, top & bottom door frames (No’s. 11, 12, 13 & 14) onto a level surface. Secure the top and bottom frames to the uprights using 2x80mm screw per corner, ensuring the screws do NOT protrude through the front of the door framing. 8x80mm Screws Pre drill hole 80mm screw 14 12 IMPORTANT : Pre-drill before fxing screws. The internal lip of the door frame should be postioned on the inside of the building. 14 12 13 11 IMP ...