Kramer ASPEN-32UFX Quick Start Manual

P/N: 2 9 0 0 - 3 0 0 9 4 2 QS Rev: 2 Scan for full manual ASPEN-32UFX Quick Start Guide This guide helps you install and use your ASPEN-32UFX for the first time. Go to www.kramerav.com/downloads/ASPEN-32UFX to download the latest user manual and check if firmware upgrades are available. Step 1: Check what’s in the box ASPEN-32UFX Programmable 32 port 12G SDI Router 1 Set of rack ears 1 Quick start guide 1 Power adapter and cord 4 Rubber feet Step 2: Get to know your ASPEN-32UFX # Feature Function 1 RS-232 (G,Rx,Tx) Terminal Block Connector Connect to a PC or remote controller. 2 POWER 12V DC Terminal Block Connector Dual power supply for redundancy: PS 1 – primary power connector PS 2 – redundant power connector (optional). Connect each power adapter into a separate branch circuit employing a separate service ground. 3 RESET Button Press briefly to restart the system. Press for 5 seconds to reset IP settings to factory default values. The device powers up and loads the factory default values: IP address: 192.168.1.39; Mask: 255.255.255.0; Gateway 192.168.1.1. 4 ETHERNET RJ-45 Connector Connect to a PC via LAN and also used for firmware upgrade. 5 LOOP BNC Connector Connect to the GENLOCK connector of the next unit in the daisy chain or terminate with 75Ω. 6 GENLOCK BNC Connector Connect to the GENLOCK source. 7 PORTS BNC Connectors (32) Connect to sources and acceptors. Step 3: Install ASPEN-32UFX Install ASPEN-32UFX using one of the following methods: • Remove the three screws from each side of the unit, reinsert those screws through the rack ears and mount on a 19" rack. • Attach the rubber feet and place the unit on a flat surface.

Each ASPEN-32UFX port can be defined as an input or an output, enabling flexible configurations such as 1x31distribution amplifiers, 31x1 routers or any other possible input-output combination. By default, the ASPEN-32UFX is set to operate as a 16x16 router: PORT 1 to PORT 16 as the inputs, and PORT 17 to PORT 32 as the outputs. Always switch OFF the power on each device before connecting it to your ASPEN-32UFX. Optionally, daisy-chain the ASPEN-32UFX by looping the genlock source to the next machine. RJ-45 Pinout: PIN EIA /TIA 568B PIN Wire Color 1 Orange / White 2 Orange 3 Green / White 4 Blue 5 Blue / White 6 Green 7 Brown / White 8 Brown Step 5: Connect the power Connect the 12V DC power supply to ASPEN-32UFX and plug it into the mains electricity. You can add a second power supply (not supplied in the package) for backup. Safety Instructions Caution: There are no operator serviceable parts inside the unit. Warning: Use only the Kramer Electronics power supply that is provided with the unit. Warning: Disconnect the power and unplug the unit from the wall before installing. See www.KramerAV.com for updated safety information.

Web Pages: RS-232 and Ethernet: RS-232 Protocol 3000 Baud Rate: 115,200 Stop Bits: 1 Data Bits: 8 Parity: None Command format example (define port 1 as an input port): #PORT-DIRECTION 1,IN ~01@PORT-DIRECTION 1,IN TCP/IP Parameters IP Address: 192.168.1.39 UDP Port #: 50000 Subnet mask: 255.255.0.000 Maximum UDP Connections: 20 Default gateway: 192.168.0.1 TCP Port #: 5000 Maximum TCP Connections: Unlimited Full Factory Reset Web Page: Device Settings Web page. Protocol 3000: Use “Factory” command: #FACTORY Rear panel RESET button: Press RESET for 5 seconds while the machine is on. The device automatically resets and powers up again, loading factory default values. Authentication User: Admin Password: Admin Configure the ports via the Video Switching Web page: • Define each port as an input or output by clicking a port number. • Toggle Mute (M) on each output. • Click a white button in the matrix to switch an input to an output. = current input to output routing state = optional input to output routing

Video 75Ω on BNC connectors (by default, 1 to 16 are set as inputs and 17 to 32 are set as outputs) 1 Genlock 75Ω on a BNC connector 1 Genlock Loop Passive loop output on a BNC connector SMPTE Standards 12G-SDI SMPTE ST-2082-1 3G HD-SDI SMPTE 424M HD-SDI SMPTE 292M SDI SMPTE 259M/344M Video Max Resolution 4K@60Hz (4:2:2) Max Bandwidth 12Gbps Controls Remote RS-232 Ethernet Web pages Reach SD Signals Up to 300m HD Signals For 1.5GHz, up to 200m For 3GHz, up to 100m For 6GHz, up to 100m UHD Signals For 12GHz, up to 80m Coupling DC Power Consumption 12V DC, 2A Source 12V DC, 5A Environmental Conditions Operating Temperature 0° to +40°C (32° to 104°F) Storage Temperature -40° to +70°C (-40° to 158°F) Humidity 10% to 90%, RHL non-condensing Regulatory Compliance Safety CE Environmental RoHs, WEEE Enclosure Size 19”, 1U Type Aluminum Cooling Fan ventilation General Net Dimensions (W, D, H) 43.64cm x 10cm x 4.36cm (17.18" x 4" x 1.72") Shipping Dimensions (W, D, H) 55cm x 27.6cm x 10.7cm (21.7" x 10.87" x 4.21") Net Weight 1kg (2.2lbs) Shipping Weight 1.9kg (4.2lbs) approx. Accessories Included Power cord Specifications are subject to change without notice at www.kramerav.com