Kramer PT-872xr Quick Start Manual

P/N: 2 9 0 0 - 3 0 1 0 0 5 QS Rev: 1 Scan for full manual PT-872xr Quick Start Guide This guide helps you install and use your PT-872xr for the first time. Go to www.kramerav.com/downloads/PT-872xr to download the latest user manual and check if firmware upgrades are available. Step 1: Check what’s in the box PT-872xr HDMI 4K Line Receiver 4 Rubber feet 1 Quick start guide 1 Power adapter and cord 1 Bracket set Step 2: Get to know your PT-872xr # Feature Function 1 LED Indicators IN Lights when an active source is connected to HDMI IN on the WP-871xr. 2 OUT Lights when an active acceptor is connected to HDMI OUT on the PT-872xr. 3 ON Lights when power is connected to the device. 4 HDMI OUT Connector Connect to an HDMI acceptor. 5 SETUP DIP-switches Set the operation DIP-switches. Both DIP-switches are set to OFF (up) by default. Always set the DIP-switches identically on transmitter and receiver devices. DIP-switch 1: Compression Options OFF (up) – Standard compression level. ON (down) – High compression level for additional range extension. DIP-switch 2: Compression Setup OFF (up) – Enable compression (mandatory). ON (down) – For future use. 6 DGKAT2 IN RJ-45 Connector Connect to the DGKat-2.0 OUT connector on the WP-871xr using twisted pair cable. 7 12V DC Connector Connect the power adapter to the device. Step 3: Install the PT-872xr Install PT-872xr using one of the following methods: • Attach the rubber feet and place the unit on a flat surface. • Fasten a bracket (included) on each side of the unit and attach it to a flat surface. For more information go to www.kramerav.com/downloads/PT-872xr. • Mount the unit in a rack using an optional RK-4PT rack adapter. Step 4: Connect the inputs and outputs Always switch OFF the power on each device before connecting it to your PT-872xr. For best results, we recommend that you always use Kramer high-performance cables to connect AV equipment to the PT-872xr.

both ends of the shield must be soldered to the connectors for the products to function properly. Do not use any jumpers, unshielded wall plates or mid-span cable connections. These extenders are not compatible with HDBaseT technologies. Prior to signal extension, ensure that the extension line cable is lying straight and not coiled. Step 5: Connect the power Connect the 12V power adapter to the PT-872xr and plug it into the mains electricity. This device provides power to its counterpart via DGKat 2.0. Each device can provide or accept power over cable (PoC) via DGKat 2.0. Safety Instructions Caution: There are no operator serviceable parts inside the unit. Warning: Use only the Kramer Electronics power supply that is provided with the unit. Warning: Disconnect the power and unplug the unit from the wall before installing. See www.KramerAV.com for updated safety information. Technical Specifications Inputs 1 DGKAT 2.0 On a female RJ-45 connector Outputs 1 HDMI On a female HDMI connector Video Transmitted Data Bandwidth Up to 18Gbps (6Gbps per graphic channel) Max Resolution 3840x2160@60Hz (4:4:4) 24bpp at high compression level 4096x2160@60Hz (4:4:4) 24bpp at standard compression level Compliance HDMI 2.0, HDCP 2.2, HDR 10 Reach Extension We recommend that you use Kramer shielded cables to achieve optimum extension ranges. Standard Compression Level Up to 40m (130ft) at 4K@60Hz (4:4:4) Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp) High Compression Level Up to 60m (200ft) at 4K@60Hz (4:4:4) Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp) Controls Front Panel IN, OUT and ON LEDs Rear Panel DIP-switches Power Consumption 12V DC, 600mA when coupled with a compatible transmitter Source 12V DC, 2A Environmental Conditions Operating Temperature 0° to +40°C (32° to 104°F) Storage Temperature -40° to +70°C (-40° to 158°F) Humidity 10% to 90%, RHL non-condensing Regulatory Compliance Safety CE, UL Environmental RoHs, WEEE Enclosure Size Pico Tool Net Dimensions (W, D, H) 6.2cm x 5.2cm x 2.5cm (2.4" x 2.05" x 1") Shipping Dimensions (W, D, H) 15.7cm x 12cm x 8.7cm (6.2" x 4.7" x 3.4") Net Weight 0.1kg (0.2lbs) Shipping Weight 0.52kg (1.2lbs) approx. Type Aluminum Cooling Convection ventilation Accessories Included 1 Power adapter, 1 power cord Specifications are subject to change without notice at www.kramerav.com