KickAss OUTBACK Series Manual 

before using the refrigerator. TABLE OF CONTENTS 1 1 1 2 2 2 3 3 4 5 5 6 7 Features Features Safety Instructions Safety Instructions Notes on using the product Notes on using the product Operation Operation Power Power Cable Specification Cable Specification Using The Fridge Using The Fridge Single Zone Single Zone Dual Zone Dual Zone USB Charging Port & Thermostat Override Switch USB Charging Port & Thermostat Override Switch Cleaning and Maintenance Cleaning and Maintenance Troubleshooting Troubleshooting Error Codes Error Codes Features Safety Instructions Notes on using the product Operation Power Cable Specification Using The Fridge Single Zone Dual Zone USB Charging Port & Thermostat Override Switch Cleaning and Maintenance Troubleshooting Error Codes

Ÿ Efficient electronic technology, low energy consumption Ÿ Multi-voltage system (DC 12-24 Volt) and (AC 100-120/220-240 Volt) Ÿ Digital Battery Protection - protects your vehicle battery effectively Safety Instructions Ÿ Warning: Do not touch exposed cables. Ÿ Warning: Do not use fridge if you suspect any connections could be wet. Ÿ When using the fridge please ensure the circuit being used is fused. Ÿ Any installation of DC power sources should be handled by a qualified professional. Ÿ Make sure the source voltage is correct. Please refer to the technical data label for the voltage data. Ÿ Do not place any electrical devices inside the refrigerator as moisture could harm these devices. Notes On Using The Product Ÿ Your refrigerator requires good ventilation, especially around the vents of the refrigerator; allow a gap of at least 200mm around the vents and 100mm around the rest of the unit. Ÿ Avoid humidity: humidity inside the appliance can form frost and impair cooling. Do not allow frost to build up. Ÿ Do not wash the appliance using a hose or running water and do not submerge the unit, as water will damage the electronics. Ÿ Avoid placing your refrigerator near a heat source. A cooler environment helps the refrigerator work more efficiently and keep the contents cool. Ÿ Place the refrigerator on a flat surface and away from any edges. When using the fridge in a vehicle, please use a fastening device to secure it. 1

(24V System) to operate. If the voltage drops below this, the fridge will stop running. Cable Specification The DC cables must have a suitable cross-section for their length, according to this table: *Note: The length is from the battery to the refrigerator. Cable Area 12V Max Cable Length* 24V Max Cable Length* [mm2] AWG [m] [ft.] [m] [ft.] 2.5 13 2.5 8 5 16 4 11 4 13 8 26 6 9 6 20 12 39 10 7 10 33 20 66 2 DC SOCKET AC ~ 100-240V 12V ANDERSON SOCKET Operation Power The electronic control module powers the compressor motor and has the function of a three stage battery protection. When the input voltage drops below the minimum, the compressor will cut out; when the voltage comes back up to the cut-in value, the compressor will restart automatically.

3 Press The TEMPERATURE SETTING MENU will open. Within this menu you can use the or buttons to change the setting. If you want to continue normal operation, wait 5 seconds for the fridge to return to the home screen or press again to enter the TEMPERATURE TYPE MENU. Within the TEMPERATURE TYPE MENU you can use the or buttons to change the setting from CELSIUS to FAHRENHEIT. If you want to continue normal operation, wait 5 seconds for the fridge to return to the home screen or press again to enter the BATTERY PROTECTION MENU Within the BATTERY PROTECTION MENU you can use the or buttons to change the setting from Low (LO) to Medium (NE) to High (HI). The three voltage settings are as follows : (KickAss recommends you keep the setting on HI) SET SET SET Setting Cut Out Voltage Cut In Voltage LO NE HI 10.1 11.4 11.8 11.1 12.2 12.6 ON/OFF button + Button - Button Set button Digital display Single Zone: To Turn ON: 1. Plug in the AC or DC power cable. 2. Hold the button for 4 seconds, until the green LED is illuminated. * When the unit is plugged in and OFF, an orange LED will be illuminated.

or buttons to change the setting. If you want to continue normal operation, wait 5 seconds for the fridge to return to the home screen or press again to enter the RIGHT ROOM TEMPERATURE SETTING MENU. The RIGHT ROOM TEMPERATURE SETTING MENU will open. Within this menu you can use the or buttons to change the setting. If you want to continue normal operation, wait 5 seconds for the fridge to return to the home screen or press again to enter the TEMPERATURE TYPE SCREEN. Within the TEMPERATURE TYPE MENU you can use the or buttons to change the setting from CELSIUS to FAHRENHEIT. If you want to continue normal operation, wait 5 seconds for the fridge to return to the home screen or press again to enter the BATTERY PROTECTION MENU. Within the BATTERY PROTECTION MENU you can use the or buttons to change the setting from Low (V ) to Medium (V ) to High (V ). L M H The three voltage settings are as follows : (KickAss recommends you keep the setting on V ) H Dual Zone ON/OFF button + Button Set button 888 V VL VM VH 888 888 Left Room Compressor Running Power Compressor Running WiFi Indicator (App) Fault Notification Battery Protection High Battery Protection Medium Battery Protection Low Source Voltage Left Room Temp Right Room Temp Right Room Compressor Running - Button SET SET SET SET Setting Cut Out Voltage Cut In Voltage VL VM VH 10.1 11.4 11.8 11.1 12.2 12.6 4

Thermostat Override Switch USB Charging Outlet Ÿ USB Port – This USB port can be used to charge small devices. E.g. mobile phones and remote controllers. The socket is rated to 500mA / 5 Volts. Ÿ Thermostat Override Switch – If your digital thermostat fails and you are unable to set the temperature, turn this switch to Emergency override. This enables the fridge to run until you reach a service centre to replace the faulty component. Please Note: If emergency override is enabled the compressor will attempt to run 100% of the time. This removes the ability to set the internal temperature and will increase power usage (Total consumption) and is not recommended for everyday use. 5 Cleaning and Maintenance Ÿ Clean the appliance inside and out with a damp cloth every week. If it is dirty, use sodium bicarbonate dissolved in lukewarm water to clean the unit. Ÿ Do not use abrasive products, detergents or soap. After washing, rinse with clean water and dry carefully. Ÿ Do not leave the refrigerator off with food inside or lid closed. Ÿ Never clean the appliance under running water.

Ÿ Check if the plug and the socket have a good connection Ÿ Check if the fuse has been burned out Ÿ Check if the appliance has been turned on (Press and hold button for 4 seconds) The appliance is not turning on Ÿ Too much food inside the refrigerator Ÿ The lid is unlocked/or open Ÿ The lid seal is broken, obstructed or deformed Ÿ Problems arising from poor ventilation Ÿ There is too much warm product inside Ÿ There is no room around the fridge and vents Ÿ There is a heat source near the unit Ÿ The temperature setting is inappropriate Bad performance in refrigeration Ÿ This is normal, due to the flow of the refrigerant. Sound of water from inside the unit Ÿ The setting temperature is too low Ÿ Thermostat override switch is enabled The food inside is frozen Ÿ The refrigerator is not placed on a level surface Ÿ Some part has come loose inside the refrigeration compartment (contact KickAss Products) Unusual noise when refrigerator is working 6

four seconds. Code Reason / Solution ERR1 or ERR2 (On Display instead on temperature) Faulty temperature probe Ÿ Contact KickAss 1 Flash Low Voltage § Please check the source voltage to ensure it is above the cut out. Try lowering the voltage cut out setting to LO. § The vehicle cabling may be inadequate or unsuitable, please refer to cable specifications table for correct cable thickness. § Try the refrigerator on a different power source. 2 Flashes Fan or compressor running issue § Fan is drawing too many Amps (Over 1 Amp) – Replace Fan. § The compressor is drawing too many Amps (Over 12 Amps). § Possible Electronic Box or compressor fault § Contact KickAss 3 Flashes The compressor speed is too low § Reduce products / items inside unit § Move unit to a lower ambient temperature § Clean vents and ensure clear air flow over compressor 4 Flashes Ambient Temperature too high § Clean vents and ensure clear air flow § Fan Fault – Replace fan 7