Larson Electronics EPLC2-LED-50W-RT-JB5 Instruction Manual

Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1 of 2 50W Explosion Proof LED Flood Light Fixture C1D2, C2D1/C2D2 - Serviceable Junction Box Instruction Manual This explosion proof light is designed for illumination of industrial locations. It uses the latest in solid state lighting technology for long life, low maintenance and high efficiency. The unique design focuses the light where it is needed, giving improved efficiency over a conventional HID luminaire. An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any nominal 100-277V AC 50/60 Hz or 11-25 Volts AC/DC power supply (depending on model) without any variation in light output. WARNING To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and maintained by a qualified electrician only, in accordance with all applicable electrical codes. To avoid electric shock: • Be certain electrical power is OFF before and during installation and maintenance. • Luminaire must be connected to a wiring system with an equipment-grounding conductor. To avoid explosion: • Make sure the supply voltage is within the luminaires’ voltage rating. • Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere. • Do not operate in ambient temperatures above those indicated on the luminaire nameplate. • Do not operate if the lens is cracked or damaged. All fasteners should be properly seated. For supply connections, use wire rated for at least 110°C Recommended mounting height is 25-40 feet. MOUNTING This fixture offers an adjustable surface mounting system that allows this fixture to be mounted to any flat surface including walls and ceilings. A single ½-13 bolt is used to mount the fixture to the surface. MOUNTING HOLE ADJUSTMENT SCREW TIGHTEN ADJUSTMENT SCREW ONCE IN DESIRED ANGLE

Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2 of 2 WIRING (see attached wiring diagram) This unit comes preconfigured with selected voltage, and beam angle. Position device near work area for operation. Run cable to nearby power source. Insert and twist-lock explosion-proof plug into a compatible receptacle within the hazardous environment. See plug operation below. PLUG OPERATION Electrical connection between plug and compatible receptacle is accomplished after plug fully inserts into receptacle and rotated clockwise. 1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug straight all the way into receptacle until it cannot go further. 2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also mechanically locks plug into receptacle so it cannot be pulled out. 3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out. Follow all applicable NEC, local, and state electrical codes. MAINTENANCE Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing maintenance. Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void the warranty. 1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine checks to be made on a yearly basis. Frequency of use and environment should determine this. It is recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B: Recommended practice for Electrical Equipment. 2. The lens should be cleaned periodically as needed to ensure continued photometric performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid cleaner. 3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed. 4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated. THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [email protected] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE. PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION. WARNING: CHECK NAMEPLATE FOR PROPER VOLTAGE. DAMAGE FROM IMPROPER VOLTAGE MAY VOID WARRANTY.