Siemens 5TC1585 Operating Instructions Manual

Détecteur de mouvement Betriebsanleitung Operating Instructions Manual de instrucciones Manuel d'utilisation 2516534149_01

• Rectangular detection area (max. 14 m x 17 m). • Mixed light measurement suitable for fluorescent lamps (FL/PL/ESL), halogen/incandescent lamps and LEDs • Integrated button • Different models: • 5TC1585 Motion detector for normal requirements • 5TC1586 For Master /Slave Switching. Proper Use • The detector controls the lighting. • It is designed for wall mounting in an interior switch range, e.g. in a corridor, staircase, cellar, toilet, etc. • For use in normal ambient conditions. Connection Use the same external conductor for all detectors. Secure device with an upstream type B or type C circuit breaker (EN 60898-1) with a maximum of (10 A L/L). Individual switching (3 – wire detector) As master, the detector detects presence and brightness and controls lighting. 2516534149_01 5TC1585

If the detection area covered by a single detector is insufficient (in large rooms), then several detectors can be operated in parallel by connecting the P terminals. The master 5TC1585 measures brightness and controls the lighting. The other detectors, slaves 5TC1586, merely provide presence information. A maximum of 6 detectors can be connected over a length of 50 m. Installation For installation in device housing, concealed housing size 1. Observe the recommended installation height of 0.8 m – 1.2 m! Ensure that there are no obstructions as infrared rays cannot pass through solid objects. The detector is not suitable for intruder alarm systems! Detection Area 5TC1585 5TC1586 5 2516534149_01

 Disconnect power source.  Connect detector according to the wiring diagram (see section connection)  Screw down the detector in the flush-mounted box   Position the button and frame on the detector    Position the adapter frame ④ Note: The frames should be ordered separately in function of the series Miro or Style. The button and adapter frame ④ should be ordered separately according to the following table: Description and settings MLFBs Description 5TG6278-5TW00 Adapter frame and button, titan white 5TG6278-5WH00 Adapter frame and button,polar white 5TG6278-5AM00 Adapter frame and button,aluminium metallic 5TG6278-5CM00 Adapter frame and button,carbon metallic 5TG6278-5SW00 Adapter frame and button,matt white 5TG6278-5SB00 Adapter frame and button,matt black 5TG6278-5AC00 Adapter frame and button,anthracite 5TG6278-5PM00 Adapter frame and button, platinum metallic 5TG6278-5CH00 Adapter frame and button, chocolate 2516534149_01    ④    ④

You can set different brightness values with the brightness potentiometer (factory setting 500 lx). Set potentiometer to desired switch-on brightness (5 to 1000 lux/on). On the on setting the detector always responds to movement, regardless of the brightness. Turn the potentiometer to Teach-in ; after 20 s (red LED flashes) the detector saves the current surrounding brightness as the new switch-on brightness. Setting the time delay (TIME) If the detector detects no further movement, it switches off after the set time delay. If you want to change the preset time (factory setting 10 min) Set the potentiometer to the desired time (10 s, 1 min, 5 min, 10 min, 30 min). If you wish to use the pulse function (e.g. for a staircase light timer switch) Set the potentiometer to . As long as motion is detected, the contact closes every 10 s for 0.5 s. Test detection area (walking test) The walking test is used to test the detection area and to restrict it if necessary. Set the time potentiometer (TIME) to test ▻ The detector always responds to movements (regardless of brightness and configuration type). ▻ After the detector has detected a movement, the contact switches on for 2 s. Performing the walking test using the button (only for slave devices) Press the button for 10 s ▻ If motion is detected the red LED on the slave lights up. ▻ Test mode is activated for 10 min. Briefly press the button ▻ The test mode is ended and the detector returns to normal operation.  Recommended guide values 2516534149_01

Staircase light function – corridor off/corridor on With the corridor off staircase light function the light can be switched on and off manually using the button at any time. With corridor on it can be switched on manually but not switched off. The light will not be switched off again until after the set time delay. Configuration type – auto/man auto = fully automatic The lighting is switched on and off automatically (based on presence, absence and brightness) man = semi-automatic The lighting is always switched on manually. It is switched off by the detector. Manual operation using the button (internal or external) The button can be used to manually switch the lighting at any time. Switching on manually When the button is pressed briefly, the light switches on for a certain time (depending on the duration of motion and the set time delay). Switching off manually If the light is switched on, it can be switched off for a certain time by briefly pressing the button (depending on the duration of the motion and the set time delay). Afterwards, the detector returns to normal operation. Normal Operation Normal Operation > 30 s + set follow-up time > 30 s + set follow-up time 2516534149_01

intervals The detector is in the start -up phase Flashes rapidly Error flashing, the detector has found an error Flickers for 20 s Teach-in via potentiometer is activated Lights up or flickers irregularly The detector is in walking test mode. Troubleshooting Fault Cause Light does not switch on or off if presence is detected and in darkness Lux value is set too low; detector set to semi- automatic; light was switched off manually via button; person not within detection area; obstruction(s) interrupting detection; time delay set too short Light stays on with detection of presence despite sufficient brightness Lux value is set too high; light was briefly switched on manually via button detector is in test mode Light does not switch off, or light switches on spontaneously when no one is present Thermal sources of interference in the detection area: fan heaters, incandescent lamps/halogen spotlights, moving objects (e.g. curtains hanging in open windows); load (EBs, relays) not cleared Button does not work Device still in the start-up phase Device does not respond Short circuit or several phases in parallel switching! Disconnect detector from the power supply for 5 min (thermal fuse) Error flashing (4 x per second) Error in self-test; device not functional! 2516534149_01

Frequency: 50/60 Hz Standby output: 0.4 W +/– 15% Switching load: L/L: 10 A with cos ϕ = 1, (not with 5TC1586) Minimum load: 10 mA, (not with 5TC1586) Contact type A: µ contact, (not with 5TC1586) Switching capacity A: Incandescent/halogen 2300W, (not with 5TC1586) Compact/fluorescent lamps: 1150 VA, (not with 5TC1586) LED lamps < 2 W: type. 40 W > 2 W: type. 450 W, (not with 5TC1586) Protection rating: IP 20 in accordance with EN 60529 Operating temperature: –15 °C … +45 °C Brightness setting range: 5 - 1000 lx, (not with 5TC1586) Lighting time delay: 10 s (pulse) -30 min, (not with 5TC1586) Installation height 0.8 – 1.2 m Detection angle: 170° Detection area: – across 14 x 17 m – frontal 12 x10 m Dimensions 10 mm 5TC1585 5TC1586 Rigid cable 2516534149_01 * Note: for P terminal max 1,5mm2, solid rigid conductor. *